Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SEPARATION PROCESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Effect of Viscosity of a Deep Eutectic Solvent on CO 2 Capture Performance in an Energy-Efficient Membrane Contactor-Based Process

Greenhouse gas contributions to climate change have driven intense interest in the separation of CO 2 from wet flue gas streams. Deep eutectic solvents (DESs) are an emerging class of highly selective CO 2 absorbents. A prototypical DES, reline, is a mixture of choline chloride and urea. Reline is a thermally stable, nontoxic, and biodegradable solvent with negligible volatility and is inexpensive. We demonstrate a scalable and energy-efficient hollow fiber membrane contactor (HFMC)-based process using a green solvent for CO 2 capture. This process uses reline in HFMC to provide close interfacial interactions and contact between DES and CO 2 . This approach overcomes the disadvantages associated with direct absorption in DES and could potentially be applied to a variety of solvent-based CO 2 capture methods. Commercial, low-cost polymer hollow fiber membranes were evaluated for the capture of CO 2 with reline. From a mixed gas containing N 2 and CO 2 , the DES-based HFMC separated CO 2 with a purity of 97 mol %. The effect of the viscosity of reline on the CO 2 capture performance was investigated by adding water to the reline. The addition of water to reline significantly reduced its viscosity, which led to a permeate flux of 170 mmol/(m 2 ·h) at 35 °C, 4 bar, and 60 wt % water in solvent, which was approximately 8 times higher than that of the pure reline in the membrane contactor system. In situ Fourier transform infrared spectroscopy and nuclear magnetic resonance (NMR) revealed that reline absorbs CO 2 by physical absorption without forming new chemical compounds and that CO 2 separation by reline occurs via the pressure swing mechanism. This research provides fundamental insights about green physical solvent-based separation processes and a pathway toward industrial deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling and Scaling up of Membrane Modules Leveraging Dimensional Analysis

In the current analysis, we study the separation performance using membrane modules through dimensional analysis (DA). We formulate the main process equations to identify relevant dimensionless numbers inherent in the physics. In particular, we identify that the critical step in the separation process is mass transfer through the selective layer. Remarkably, the dimensionless feed flow (DFfeed) emerges as a crucial factor in describing this process. Not only does DFfeed directly appear in the governing equations, but it also holds a physical significance associated with the time scales for the mass transfer across the feed side and through the selective layer. Regarding the output performance variables, we consider the recovery, stage cut, productivity and purity. In this context, we profit from experimental data and CFD simulations to evaluate the separation performance of the modules when varying the input flowrate, the scale of the module, and the CO2 permeance. These datasets enable us to establish correlations between performance metrics and the dimensionless feed flow. Using simple power functions of DFfeed, we obtain R2 coefficients exceeding 0.99, indicating the accuracy of the correlations built in the present work. In the future, we wish to use DA to understand key transport mechanisms, predict and control module performance, and challenge the universality of these findings by testing various gas separations across different membrane modules beyond our case study.

Pedrozo, Hector A.↗

Preliminary Testing of a Continuous Cryopump for Primary Fusion Device Pumping and Direct Internal Recycling

Here, the concept of directly recirculating fusion machine exhaust gas, bypassing the tritium plant, to make fuel pellets was proposed in the 1990s and later termed direct internal recycling (DIR). In the DIR concept, the residual fusion fuel in the machine exhaust stream is separated from impurities locally and diverted directly to the fueling systems, bypassing isotopic separation and other processing equipment, and therefore significantly reducing the required size of the fuel processing plant, reducing plant inventory, and thus increasing the economic viability of fusion as an energy source. One concept for DIR consists of a series of cryogenic pumps to separate the impurities from the machine exhaust gas using different triple point temperatures and saturation curves of exhaust constituents. In this concept, the plasma exhaust is initially passed through an impurity trap operating at ~25–30 K to desublimate impurities such as hydrocarbons, argon, oxygen, and nitrogen. The resulting process stream will consist of DT fuel and helium. The process stream is then pumped by a continuous cryopump known as a “snail pump.” This pump is a steady-state continuous cryopump that desublimates all remaining exhaust gas constituents while allowing helium, a byproduct of the fusion reaction, to pass through. The helium is pumped to the tritium plant for processing while the desublimated material is continuously scraped off, heated up, and transported to the fueling system. This article will present the cryogenic DIR concept and outline the design and operation of the snail pump, along with results from preliminary testing. Tests to assess pumping and separation efficiency found that at D2 flows below 50.7 Pa ⋅ m3/s with 1% helium, the pump is capable of pumping and separating the gas with a resulting DIR fraction of >99%, with no helium entrained in the primary fuel exhaust stream. The main limitation is due to the thermal performance of the cryogenic circuits of the pump, which will be addressed in future testing.

Gebhart III, Trey E. [Oak Ridge National Laborator↗

Method and apparatus for bio-regenerative life support system

A life support system is disclosed for human habitation (cabin) which has a bioregenerative capability through the use of a plant habitat (greenhouse) whereby oxygen-rich air from the greenhouse is processed and used in the cabin and carbon dioxide-rich air from the cabin is used in the greenhouse. Moisture from the air of both cabin and greenhouse is processed and reused in both. Wash water from the cabin is processed and reused in the cabin as hygiene water, and urine from the cabin is processed and used in the greenhouse. Spent water from the greenhouse is processed and reused in the greenhouse. Portions of the processing cycles are separated between cabin and greenhouse in order to reduce to a minimum cross contamination of the two habitat systems. Other portions of the processing cycles are common to both cabin and greenhouse. The use of bioregenerative techniques permits a substantial reduction of the total consumables used by the life support system.

Cullingford, Hatice S.↗

A Robust, Gravity-Insensitive, High-Temperature Condenser for Water Recovery

Regenerative life support systems are vital for NASA's future long-duration human space exploration missions. A Heat Melt Compactor (HMC) system is being developed by NASA to dry and compress trash generated during space missions. The resulting water vapor is recovered and separated from the process gas flow by a gravity-insensitive condenser. Creare is developing a high-temperature condenser for this application. The entire condenser is constructed from metals that have excellent resistance to chemical attack from contaminants and is suitable for high-temperature operation. The metal construction and design configuration also offer greatest flexibility for potential coating and regeneration processes to reduce biofilm growth and thus enhancing the reliability of the condenser. The proposed condenser builds on the gravity-insensitive phase separator technology Creare developed for aircraft and spacecraft applications. This paper will first discuss the design requirements for the condenser in an HMC system that will be demonstrated on the International Space Station (ISS). Then, it will present the overall design of the condenser and the preliminary thermal test results of a subscale condenser. Finally, this paper will discuss the predicted performance of the full-size condenser and the development plan to mature the technology and enhance its long-term reliability for a flight system.

Chen, Weibo↗

Ultra-selective ligand-driven separation of strategic actinides

Abstract Metal ion separations are critical to numerous fields, including nuclear medicine, waste recycling, space exploration, and fundamental research. Nonetheless, operational conditions and performance are limited, imposing compromises between recovery, purity, and cost. Siderophore-inspired ligands show unprecedented charge-based selectivity and compatibility with harsh industry conditions, affording excellent separation efficiency, robustness and process control. Here, we successfully demonstrate a general separation strategy on three distinct systems, for Ac, Pu, and Bk purification. Separation factors (SF) obtained with model compound 3,4,3-LI(1,2-HOPO) are orders of magnitude higher than with any other ligand currently employed: 10 6 between Ac and relevant metal impurities, and over 10 8 for redox-free Pu purification against uranyl ions and trivalent actinides or fission products. Finally, a one-step separation method (SF > 3 × 10 6 and radiopurity > 99.999%) enables the isolation of Bk from adjacent actinides and fission products. The proposed approach offers a paradigm change for the production of strategic elements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Airtight metallic sealing at room temperature under small mechanical pressure

Metallic seals can be resistant to air leakage, resistant to degradation under heat, and capable of carrying mechanical loads. Various technologies – such as organic solar cells and organic light emitting diodes – need, at least benefit from, such metallic seals. However, these technologies involve polymeric materials and can tolerate neither the high-temperature nor the high-pressure processes of conventional metallic sealing. Recent progress in nanorod growth opens the door to metallic sealing for these technologies. Here, we report a process of metallic sealing using small well-separated Ag nanorods; the process is at room temperature, under a small mechanical pressure of 9.0 MPa, and also in ambient. The metallic seals have an air leak rate of 1.1 3 1023 cm3 atm/m2 /day, and a mechanical shear strength higher than 8.9 MPa. This leak rate meets the requirements of organic solar cells and organic light emitting diodes.

36 MATERIALS SCIENCE↗

Advanced Membrane Separation Technologies for Energy Recovery from Industrial Process Streams

Recovery of energy from relatively low-temperature waste streams is a goal that has not been achieved on any large scale. Heat exchangers do not operate efficiently with low-temperature streams and thus require such large heat exchanger surface areas that they are not practical. Condensing economizers offer one option for heat recovery from such streams, but they have not been widely implemented by industry. A promising alternative to these heat exchangers and economizers is a prototype ceramic membrane system using transport membrane technology for separation of water vapor and recovery of heat. This system was successfully tested by the Gas Technology Institute (GTI) on a natural gas fired boiler where the flue gas is relatively clean and free of contaminants. However, since the tubes of the prototype system were constructed of aluminum oxide, the brittle nature of the tubes limited the robustness of the system and even limited the length of tubes that could be used. In order to improve the robustness of the membrane tubes and make the system more suitable for industrial applications, this project was initiated with the objective of developing a system with materials that would permit the system to function successfully on a larger scale and in contaminated and potentially corrosive industrial environments. This required identifying likely industrial environments and the hazards associated with those environments. Based on the hazardous components in these environments, candidate metallic materials were identified that are expected to have sufficient strength, thermal conductivity and corrosion resistance to permit production of longer tubes that could function in the industrial environments identified. Tests were conducted to determine the corrosion resistance of these candidate alloys, and the feasibility of forming these materials into porous substrates was assessed. Once the most promising metallic materials were identified, the ability to form an alumina membrane layer on the surface of the metallic tubes was evaluated. Evaluation of this new style of membrane tube involved exposure to SO 2 containing gases as well as to materials with a potential for fouling. Once the choice of substrate and membrane materials and design were confirmed, about 150 tubes were fabricated and assembled into three modules. These modules were mounted on an industrial size boiler and their performance carefully monitored during a limited testing period. The positive results of this performance test confirm the feasibility of utilizing such a system for recovery of heat and water from industrial waste streams. The improved module design along with use of long metallic substrate tubes with a ceramic membrane on the outer surface resulted in the successful, limited scale demonstration of the Transport Membrane Condenser (TMC) technology in the GTI test facility. This test showed this technology can successfully recover a significant amount of heat and water from gaseous waste streams. However, before industry will make the investment to install a full scale TMC, a full scale system will need to be constructed, installed and successfully operated at a few industrial sites. Companies were identified that had an interest in serving as a host site for a demonstration system.

Keiser, James R.↗

Advanced Membrane Separation Technologies for Energy Recovery from Industrial Process Streams

Recovery of energy from relatively low-temperature waste streams is a goal that has not been achieved on any large scale. Heat exchangers do not operate efficiently with low-temperature streams and thus require such large heat exchanger surface areas that they are not practical. Condensing economizers offer one option for heat recovery from such streams, but they have not been widely implemented by industry. A promising alternative to these heat exchangers and economizers is a prototype ceramic membrane system using transport membrane technology for separation of water vapor and recovery of heat. This system was successfully tested by the Gas Technology Institute (GTI) on a natural gas fired boiler where the flue gas is relatively clean and free of contaminants. However, since the tubes of the prototype system were constructed of aluminum oxide, the brittle nature of the tubes limited the robustness of the system and even limited the length of tubes that could be used.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Processing iridium foil targets for the production of radioplatinum isotopes

Dissolving noble metals remains challenging because of their high reduction potentials and tendency to passivate as oxides. This barrier is acute for iridium metal targets used to produce platinum radioisotopes, where post-irradiation processing is costly and hazardous with conventional routes. Here, we report a rapid alkali-fusion method that converts Ir metal directly into chloride media compatible with downstream separations. In the process, an Ir foil is fused with Na 2 O 2 and KCl at temperatures above the KCl melting point; the molten salt enhances heat transfer and facilitates O 2− /Na + transport to the Ir surface, overcoming Ir's oxidation resistance. The fused cake is then cooled and leached in 10 M HCl, yielding Ir in solution without specialized microwave digestion or HF. Pt separation from bulk Ir was evaluated using extraction-chromatography resins. A newly formulated ionic-liquid resin containing Cyphos IL 104 (E104) was compared with two commercial resins (TrisKem TK200 and TK201). All resins achieved >90 % Ir recovery. Pt co-recovery depended on resin chemistry: TK200 recovered 85.9 % Pt, TK201 recovered 54.1 % Pt, and E104 recovered 72.9 % Pt. This study introduces a fast, scalable dissolution route for solid Ir targets and demonstrates resin choices that tune Ir/Pt separation, lowering the barrier to routine production and purification of Pt radioisotopes.

07 ISOTOPE AND RADIATION SOURCES↗

Heavy Quarks, QCD, and Effective Field Theory

The research supported by this OJI award is in the area of heavy quark and quarkonium production, especially the application Soft-Collinear Effective Theory (SCET) to the hadronic production of quarkonia. SCET is an effective theory which allows one to derive factorization theorems and perform all order resummations for QCD processes. Factorization theorems allow one to separate the various scales entering a QCD process, and in particular, separate perturbative scales from nonperturbative scales. The perturbative physics can then be calculated using QCD perturbation theory. Universal functions with precise field theoretic definitions describe the nonperturbative physics. In addition, higher order perturbative QCD corrections that are enhanced by large logarithms can be resummed using the renormalization group equations of SCET. The goal of my OJI-supported research was to apply SCET to the physics of heavy quarks, heavy quarkonium, and similar particles.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Development of processes for the production of solar grade silicon from halides and alkali metals, phase 1 and phase 2

High temperature reactions of silicon halides with alkali metals for the production of solar grade silicon are described. Product separation and collection processes were evaluated, measure heat release parameters for scaling purposes and effects of reactants and/or products on materials of reactor construction were determined, and preliminary engineering and economic analysis of a scaled up process were made. The feasibility of the basic process to make and collect silicon was demonstrated. The jet impaction/separation process was demonstrated to be a purification process. The rate at which gas phase species from silicon particle precursors, the time required for silane decomposition to produce particles, and the competing rate of growth of silicon seed particles injected into a decomposing silane environment were determined. The extent of silane decomposition as a function of residence time, temperature, and pressure was measured by infrared absorption spectroscopy. A simplistic model is presented to explain the growth of silicon in a decomposing silane enviroment.

Dickson, C. R.↗

Failure detection system design methodology

The design of a failure detection and identification system consists of designing a robust residual generation process and a high performance decision making process. The design of these two processes are examined separately. Residual generation is based on analytical redundancy. Redundancy relations that are insensitive to modelling errors and noise effects are important for designing robust residual generation processes. The characterization of the concept of analytical redundancy in terms of a generalized parity space provides a framework in which a systematic approach to the determination of robust redundancy relations are developed. The Bayesian approach is adopted for the design of high performance decision processes. The FDI decision problem is formulated as a Bayes sequential decision problem. Since the optimal decision rule is incomputable, a methodology for designing suboptimal rules is proposed. A numerical algorithm is developed to facilitate the design and performance evaluation of suboptimal rules.

Chow, E. Y.↗

A Review of Low Frequency Electromagnetic Wave Phenomena Related to Tropospheric-Ionospheric Coupling Mechanisms

Investigation of coupling mechanisms between the troposphere and the ionosphere requires a multidisciplinary approach involving several branches of atmospheric sciences, from meteorology, atmospheric chemistry, and fulminology to aeronomy, plasma physics, and space weather. In this work, we review low frequency electromagnetic wave propagation in the Earth-ionosphere cavity from a troposphere-ionosphere coupling perspective. We discuss electromagnetic wave generation, propagation, and resonance phenomena, considering atmospheric, ionospheric and magnetospheric sources, from lightning and transient luminous events at low altitude to Alfven waves and particle precipitation related to solar and magnetospheric processes. We review in situ ionospheric processes as well as surface and space weather phenomena that drive troposphere-ionosphere dynamics. Effects of aerosols, water vapor distribution, thermodynamic parameters, and cloud charge separation and electrification processes on atmospheric electricity and electromagnetic waves are reviewed. We also briefly revisit ionospheric irregularities such as spread-F and explosive spread-F, sporadic-E, traveling ionospheric disturbances, Trimpi effect, and hiss and plasma turbulence. Regarding the role of the lower boundary of the cavity, we review transient surface phenomena, including seismic activity, earthquakes, volcanic processes and dust electrification. The role of surface and atmospheric gravity waves in ionospheric dynamics is also briefly addressed. We summarize analytical and numerical tools and techniques to model low frequency electromagnetic wave propagation and solving inverse problems and summarize in a final section a few challenging subjects that are important for a better understanding of tropospheric-ionospheric coupling mechanisms.

Simoes, Fernando↗

Laser-driven hydrothermal processing: a new, efficient technique to effect separation of silica from other oxides for analysis

We report on what appeared to be an unstudied regime of laser-matter interactions, when modest-intensity, modest-fluence laser pulses struck weakly-absorbing, silica-rich material that was submerged in water: material was efficiently removed from the surface and colorless particles were left behind, decorating crater's surface. One explanation for this color loss was a transient dissolution of the material, due to the pressure and temperature pulse caused by the laser absorption and thermally-driven expansion of the material. Yet, other explanations were possible. Here, we have studied this process with laser intensity and fluence so low that no crater was formed, when a sample of natural quartzite rock was submerged in deionized water and illuminated with 40 MW cm –2 , 527 nm laser pulses. After one hundred laser pulses, the treated surface of the originally colored quartzite was colorless. We cut the quartzite in cross section and examined the colorless material on the surface with x-ray fluorescence. We report that the transition element Fe was found to be significantly depleted in this colorless layer, while Si was not. This bolsters the hypothesis that the laser exposure led to a transient hydrothermal dissolution of the material, followed by a recrystallization process of the SiO 2 that preferentially released iron oxides into the submerging water.

36 MATERIALS SCIENCE↗

SQERTSS: Dynamic rank based throttling of transition probabilities in kinetic Monte Carlo simulations

Lattice based Kinetic Monte Carlo (KMC) simulations offer a powerful simulation technique for investigating large reaction networks while retaining spatial configuration information, unlike ordinary differential equations. However, large chemical reaction networks can contain reaction processes with rates spanning multiple orders of magnitude. This can lead to the problem of “KMC stiffness” (similar to stiffness in differential equations), where the computational expense has the potential to be overwhelmed by very short time-steps during KMC simulations, with the simulation spending an inordinate amount of KMC steps / cpu-time simulating fast frivolous processes (FFPs) without progressing the system (reaction network). In order to achieve simulation times that are experimentally relevant or desired for predictions, a dynamic throttling algorithm involving separation of the processes into speed-ranks based on event frequencies has been designed and implemented with the intent of decreasing the probability of FFP events, and increasing the probability of slow process events -- allowing rate limiting events to become more likely to be observed in KMC simulations. This Staggered Quasi-Equilibrium Rank-based Throttling for Steady-state (SQERTSS) algorithm designed for use in achieving and simulating steady-state conditions in KMC simulations. Lastly, as shown in this work, the SQERTSS algorithm also works for transient conditions: the correct configuration space and final state will still be achieved if the required assumptions are not violated, with the caveat that the sizes of the time-steps may be distorted during the transient period.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A Model of Cyclic Transcriptomic Behavior in Cyanobacterium Cyanothece sp. ATCC 51142

Systems biology attempts to reconcile large amounts of disparate data with existing knowledge to provide models of functioning biological systems. Useful and predictive models aim to summarize complex and dynamic processes and represent the relationships between these processes. The cyanobacterial Cyanothece species Strain sp. ATCC 51142 is an excellent candidate for such systems studies because: (i) it displays tight functional regulation as it must separate the opposing processes of oxygen-generating photosynthesis and oxygen-sensitive nitrogen fixation temporally in the same cell, ; (ii) it has robust cyclic patterns at the genetic, protein and metabolomic levels, ; and (iii) and it has potential applications for bioenergy and carbon sequestration, and thus a predictive model of its function is of practical use. We have represented the transcriptomic data from Cyanothece 51142 under diurnal light/dark cycles as a high-level functional abstraction and describe development of a predictive in silico model of diurnal and circadian behavior in terms of regulatory and metabolic processes in Cyanothece 51142. Our model provides a way to integrate disparate data types into a framework that can be used to explain behavior, generate high-quality predictions for validation, and to suggest future experiments. We show that incorporating network topology into the model improves performance in terms of our ability to explain the behavior of the system under new conditions. The model presented robustly describes transcriptomic behavior of Cyanothece 51142 under different cyclic and non-cyclic growth conditions robustly, and represents a significant advance in the understanding of gene regulation in this important organism.

59 BASIC BIOLOGICAL SCIENCES↗

3DBFSVBF (3D BatFinder Smart Video BioFilter and Multi-class BatFinder Smart Video BioFilter) [SWR-22-88]

Bats are notoriously difficult to study, therefore, identifying specific behavioral trends and the precise environmental conditions at the time of collision requires a monitoring solution that can reliably collect relevant data. To date, thermal infrared video surveillance has been extensively applied to study bats and has proven to be a powerful yet cumbersome tool. Current analytical approaches are time consuming because data processing data has not been fully automated. In the past, steps have been taken to record avian and bat activity in conjunction with complicated image processing techniques that separate species from other moving objects within the field of view (i.e. clouds and portions of the wind turbine). Once the videos are collected, the post-processing does not allow real time monitoring and identification, leading to a delay in both studying the behavior of these species and determining the effectiveness of any impact reduction strategy being studied. Moreover, object identification capability is lacking, thus limiting the usefulness of video data. To resolve these issues, we are using open source 3D computer vision and machine learning techniques allowing for automatic detection of objects in real-time with the ability to correlate these objects with environmental variables and recording the flight paths of each object. The machine learning has been trained on 3D data and allows for automated real-time data collection, identification and tracking, thereby eliminating the need for long and tedious post-analysis processing of the videos. This machine learning model is an added feature to the previous BatFinder Smart Video BioFilter and increases the accuracy of that systems classification by increasing the accuracy of identifying bats (90% accuracy) and insects (69% accuracy) to a 97% accuracy. There are two object classifier machine learning models, Binary and multi-classification. Binary object classifier labeled BatFinder_Smart_Video_BioFilter.h5 distinguishes between biological objects and non-biological objects. The main goal of this object classifier is to ignore the turbine blades while detecting biological object flying withing the rotor swept area of the turbine. Non-biological objects have a probability of 0 and biological objects have a probability of 1. Multi-classifier labeled Multiclass_BatFinder_Smart_Video_BioFilter.h5 distinguishes between bats, birds, insects and non-biological.

Yarbrough, John↗