Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Polymer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of Dilute DIO Additive on Local Microstructure of Fluorinated, pNDI‐Based Polymer Solar Cells

The performance of all‐polymer solar cells is often enhanced by incorporating solvent additives during solution processing. Here, in particular, blends based on the model all‐polymer system PBDBT:N2200 have been shown to have increased short‐circuit current and fill factor when processed with dilute diiodooctane (DIO). However, the morphological mechanism that drives the increase in performance is often not well understood due to limitations in common characterization techniques. In this study, it is shown that a combination of X‐ray techniques with cryogenic high‐resolution transmission electron microscopy (HRTEM) analysis can provide a quantitative and spatially resolved picture of polymer chain orientation and alignment in all‐polymer blends. It is found that DIO induces vertical phase separation in PBDBT‐2F:F‐N2200 and increases donor crystallite thickness in the pi‐stacking direction leading to an acceptor‐rich film surface. However, it is also shown that DIO does not disrupt the formation of face‐on donor–acceptor interfaces. These findings suggest that dilute DIO primarily affects crystalline domain formation in single component regions as opposed to mixed regions; thus, dilute DIO can impact vertical charge transport pathways without sacrificing donor–acceptor interfacial connectivity.

Cheng, Christina↗
DOE OSTI2025

Stereochemical Control of Water Transport Properties in Thiol‐yne Polymers

Barrier polymers underpin almost every commercial sector, yet the needs of several emerging areas remain unmet by commercially‐available materials, including temporary orthopedic implants, transient health monitors, neural implants, and other long‐term implants. The ability to tune polymer composition independently of polymer structure positions thiol‐yne click chemistry as a promising platform to serve these emerging technologies. Here, this work describes the differences in the hierarchical structure of stoichiometrically identical materials which differ only in the proportion of the cis versus trans backbone alkene stereochemistry. Varying the isomer content in this way directs different temperature and rate dependent crystallization behavior, which affords control over micron‐scale structure. This investigation focuses on how these stereochemical features affect the water vapor permeation process by several methods and develops an understanding of how this unique structural regularity improves barrier performance relative to a commercially available water barrier polymer, poly(ethylene terephthalate).

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Improving Charge Transport and Environmental Stability of Carbohydrate-Bearing Semiconducting Polymers in Organic Field-Effect Transistors

Semiconducting polymers offer synthetic tunability, good mechanical properties, and biocompatibility, enabling the development of soft technologies previously inaccessible. Side-chain engineering is a versatile approach for optimizing these semiconducting materials, but minor modifications can significantly impact material properties and device performance. Carbohydrate side chains have been previously introduced to improve the solubility of semiconducting polymers in greener solvents. Despite this achievement, these materials exhibit suboptimal performance and stability in field-effect transistors. In this work, structure–property relationships are explored to enhance the device performance of carbohydrate-bearing semiconducting polymers. Toward this objective, a series of isoindigo-based polymers with carbohydrate side chains of varied carbon-spacer lengths is developed. Material and device characterizations reveal the effects of side chain composition on solid-state packing and device performance. With this new design, charge mobility is improved by up to three orders of magnitude compared to the previous studies. Processing–property relationships are also established by modulating annealing conditions and evaluating device stability upon air exposure. Notably, incidental oxygen-doping effects lead to increased charge mobility after 10 days of exposure to ambient air, correlated with decreased contact resistance. Bias stress stability is also evaluated. This work highlights the importance of understanding structure–property relationships toward the optimization of device performance

36 MATERIALS SCIENCE↗
DOE OSTI2017

Toward High Efficiency Polymer Solar Cells: Rearranging the Backbone Units into a Readily Accessible Random Tetrapolymer

Abstract Two donor–acceptor (D–A) conjugated polymers composed of the same ratio of 5‐fluorobenzothiadiazole and thiophene subunits are synthesized through different routes, providing a precisely regioregular ( 2TRR ) and a random ( 2TRA ) polymer structures. Detailed structural analyses indicate that the backbone of regioregular 2TRR has only one donor segment of bithiophene, while the backbone of random 2TRA consists of three different donor segments: thiophene, bithiophene, and terthiophene (in a ratio of 0.16:0.68:0.16). Synergetic contributions from these segments allow the “tetrapolymer” 2TRA to achieve more favorable film morphology and a higher hole‐mobility relative to 2TRR . Consequently, the random polymer 2TRA achieves a substantially higher power conversion efficiency (8.8%) than the regioregular polymer 2TRR (5.1%). Notably, the “tetrapolymer” 2TRA is readily synthesized from two monomers, rather than through complex conventional preparation required for similar multipolymers. These findings provide a novel route toward the design and synthesis of multipolymeric materials and demonstrate their potential advantages in high‐performance organic electronic applications.

Zhou, Cheng↗
DOE OSTI2021

Polymers in Lithium‐Ion and Lithium Metal Batteries

Abstract Lithium‐ion batteries play a significant role in modern electronics and electric vehicles. However, current Li‐ion battery chemistries are unable to satisfy the increasingly heightened expectations regarding energy demand and reliability. To boost the overall energy density while ensuring the safety of Li batteries, researchers have focused on alternative battery materials, such as silicon, sulfur, and Li metal. These represent promising avenues, although numerous obstacles (e.g., Si cracking, polysulfide shuttling, Li dendrites, etc.) must be tackled before batteries based on these materials can enter mass production and penetrate the mainstream market. Polymers are a class of materials that are widely used in current battery systems; however, many novel polymer chemistries may offer better performance and reliability than the current ones, and even overcome the issues of the above‐mentioned new battery materials. In this review, selected polymeric materials for solving these issues are categorized into four parts: polymer electrolytes, polymer artificial solid‐electrolyte interphases, binders, and separators. Both the current progress and the characterization methods are included. Potential future directions of energy materials research are pointed out as well.

Li, Junheng↗
DOE OSTI2018

Bis‐isoindigos: New Electron‐Deficient Building Blocks for Constructing Conjugated Polymers with Extended Electron Delocalization

Abstract Incorporation of acceptor‐acceptor (A‐A) type moieties into donor‐acceptor (D‐A) type conjugated polymers becomes a new strategy to tune their electronic properties. In this work, we first demonstrate an efficient convergent route to prepare isoindigo‐based A‐A type building blocks ‐ bis‐isoindigos ‐ via the palladium‐catalyzed oxidative coupling. Bis‐isoindigo‐based polymers show high planarity and delocalized frontier molecular orbitals with lowered LUMO and intact HOMO energy levels, in comparison with their corresponding mono‐isoindigo counterparts. Moreover, fluorine substitution on donors only lowers HOMO levels of Bis‐IID polymers. This study asserts that the D‐A‐A strategy is effective in selectively tuning FMO energy levels of conjugated polymers, complementary to the D‐D‐A approach for the HOMO energy level tuning.

Luo, Xuyi↗
DOE OSTI2017

Unusual Internal Electron Transfer in Conjugated Radical Polymers

Abstract Nitroxide‐containing organic radical polymers (ORPs) have captured attention for their high power and fast redox kinetics. Yet a major challenge is the polymer's aliphatic backbone, resulting in a low electronic conductivity. Recent attempts that replace the aliphatic backbone with a conjugated one have not met with success. The reason for this is not understood until now. We examine a family of polythiophenes bearing nitroxide radical groups, showing that while both species are electrochemically active, there exists an internal electron transfer mechanism that interferes with stabilization of the polymer's fully oxidized form. This finding directs the future design of conjugated radical polymers in energy storage and electronics, where careful attention to the redox potential of the backbone relative to the organic radical species is needed.

Li, Fei↗
DOE OSTI2019

Topotactic Synthesis of Phosphabenzene-Functionalized Porous Organic Polymers: Efficient Ligands in CO 2 Conversion

Progress toward the preparation of porous organic polymers (POPs) with task-specific functionalities has been exceedingly slow—especially where polymers containing low-oxidation phosphorus in the structure are concerned. In this work, a two-step topotactic pathway for the preparation of phosphabenzene-based POPs (Phos-POPs) under metal-free conditions is reported, without the use of unstable phosphorus-based monomers. The synthetic route allows additional functionalities to be introduced into the porous polymer framework with ease. As an example, partially fluorinated Phos-POPs (F-Phos-POPs) were obtained with a surface area of up to 591 m 2 g –1 . After coordination with Ru species, a Ru/F-Phos-POPs catalyst exhibited high catalytic efficiency in the formylation of amines (turnover frequency up to 204 h –1 ) using a CO 2 /H 2 mixture, in comparison with the non-fluorinated analogue (43 h –1 ) and a Au/TiO 2 heterogeneous catalysts reported previously (<44 h –1 ). This work describes a practical method for synthesis of porous organic phosphorus-based polymers with applications in transition-metal-based heterogeneous catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mastering the Copolymerization Behavior of Ethyl Cyanoacrylate as Gel Polymer Electrolyte for Lithium‐metal Battery Application

Polymers with strong electron-withdrawing groups (e.g., cyano-containing polymers) are attractive for a wide range of applications due to their high dielectric constant and outstanding electrochemical stability. However, the polymerization of such monomers is difficult to control with trace of water affording instant reactions, and copolymerization with other monomers without using strong acid is even more challenging. The present study demonstrates a facile approach enabling efficient and controllable copolymerization of ethyl cyanoacrylate (ECA) without adding undesired additives, achieving mechanically robust and high ion-conduction gel polymer electrolyte (GPE) for safe and long cycle-life lithium-metal batteries (LMBs). The incorporated dual-lithium salts, i.e., lithium difluoro(oxalato)borate (LiDFOB) and lithium bis(trifluoromethanesulphonyl)imide (LiTFSI) not only facilitate radical polymerization of ECA monomers by suppressing their anionic polymerization, but also promote the formation of high-ionic conducting GPE. The incorporated methyl methacrylate (MMA) monomer accelerates the radical polymerization of ECA (confirmed by DFT calculations), achieving controlled copolymerization of ECA-based copolymers. Here, the mechanically robust polymer network made by the ECA copolymer enables LMBs with both LFP cathodes and high-voltage LCO cathodes (4.5 V) operatable at different temperatures with ultra-long cycle life at 1 C (capacity retention of 81.1 % and 83.8 %, respectively, over 1000 cycles).

Min, Weixing [Nankai University, Tianjin (China)]↗
DOE OSTI2025

Polymer Size–Catalytic Activity Relationships in Solution by Fluorescence Correlation Spectroscopy

Measuring the catalytic activity of specific sizes of polymers with active catalysts in solution is typically challenging, due to limited instrument detection sensitivity and/or dynamic range. Here, a fluorescence correlation spectroscopy (FCS) method is developed to determine the catalytic activity of living polymers of a specific apparent size in solution. Deviation from a single-component FCS data fitting, as assessed by χ2, is also introduced and developed as a “speciation index”—a method to evaluate and track changes in the relative amount of distinct polymer sizes with reaction progress. These methods are enabled by incorporating a selectively reactive fluorescent monomer into growing polydicyclopentadiene or polynorbornene during ring-opening metathesis polymerization (ROMP). Compared to polynorbornene, data showed that catalysts in aggregates of polyDCPD retained higher activity for longer—outcomes not directly inferable from simple diffusional-access predictions. Here, the ability to assign catalytic activity to polymers of specific sizes, and then to determine how this activity evolves with reaction progress, support long-term goals in the development and measurement of nano-objects that possess size-dependent catalytic activity.

Active catalyst↗
DOE OSTI2020

Supramolecular and Hybrid Bonding Polymers

Staudinger established a century ago the existence of covalent macromolecules, work that led to the development of transformative materials of great benefit to society and a “quantum leap” in our understanding of biological systems. Over the past few decades the concept of supramolecular polymers has emerged–chemical systems in which structural units bond strongly to each other non-covalently. Herein, we discuss how these dynamic systems actually exist in the natural world and can create soft materials with structures, properties, and functions beyond the ones we know in Staudinger polymers. We reflect here on the potential of novel systems in which covalent and supramolecular polymers are chemically integrated and describe them as hybrid bonding polymers. This paper describes the concept with recent examples from the Stupp laboratory, and discusses their potential functions as robotic materials that mimic living matter and structures that offer new ideas on how to recycle and reuse soft materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

A glucose sensor via stable immobilization of the GOx enzyme on an organic transistor using a polymer brush

Recently, there has been significant research in the area of organic electrochemical transistors (OECTs) because of their superior aptitude of chemical and biological sensing. Here it is shown for the first time the incorporation of polymer brushes to a transistor. Polymer brushes were chosen for their biocompatible properties and their ability to covalently tether enzymes and other biomolecules to different surfaces. OECTs were fabricated from the conducting polymer poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonate), PEDOT:PSS, and polymerized from the surface a mixed polymer brush of poly(glycidyl methacrylate) and poly(2-hydroxyethyl methacrylate). The brushes were functionalized with glucose oxidase and measured in terms of electrical performance and long-term stability.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Degradable cellulose‐based polymer brushes with controlled grafting densities

ABSTRACT Cellulose‐based polymer brushes with variable grafting densities and low dispersity were synthesized by grafting poly( n ‐butyl acrylate) (PBA) side chains from cellulose‐derived backbones via ATRP. Esterification of commercially available cellulose acetate with 2‐bromoisobutyryl bromide (2‐BiBB) in NMP provided cellulose‐based macroinitiators averaging one initiation site per double glucose unit. ATRP macroinitiators averaging up to 6 initiation sites per repeating double glucose unit were prepared by acylation of microcrystalline cellulose (MCC) in LiCl/DMAc solvent system with 2‐BiBB. A series of linear macroinitiators with narrow MWD were obtained by fractional precipitation process. The content of initiating sites was determined by elemental analysis. (Meth)acrylate side chains were then grafted from the cellulose‐based macroinitiators. The prepared cellulose‐based polymer brushes showed tunable degradation rates dependent on grafting density of the brush, following two different degradation pathways, either cleavage of the main chain or detachment of the side chains. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57 , 2426–2435

Olszewski, Mateusz↗
DOE OSTI2016

Modular Polymer Biosensors by Solvent Immersion Imprint Lithography

We recently demonstrated Solvent Immersion Imprint Lithography (SIIL), a rapid benchtop microsystem prototyping technique, including polymer functionalization, imprinting and bonding. Here, we focus on the realization of planar polymer sensors using SIIL through simple solvent immersion without imprinting. We describe SIIL’s impregnation characteristics, including an inherent mechanism that not only achieves practical doping concentrations, but their unexpected 4-fold enhancement compared to the immersion solution. Subsequently, we developed and characterized optical sensors for detecting molecular O2. To this end, a high dynamic range is reported, including its control through the immersion duration, a manifestation of SIIL’s modularity. Overall, SIIL exhibits the potential of improving the operating characteristics of polymer sensors, while significantly accelerating their prototyping, as it requires a few seconds of processing and no need for substrates or dedicated instrumentation. These are critical for O2 sensing as probed by way of example here, as well as any polymer permeable reactant.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2018

Ultrafast shock compression of PDMS-based polymers

The shock response of polymers is important for a number of commercial and defense–related applications, but it is difficult to obtain empirical shock response data over the wide range of preparations and aging conditions typically found in such applications. Ultrafast compression is useful to characterize polymer shock response over a wide range of polymer initial conditions due to the high throughput of this method. To establish greater confidence in ultrafast compression experiments and to characterize the detailed shock response of several variations in a single base polymer, the results of sub–nanosecond shock compression experiments in ~5 μm thick layers of the polydimethylsiloxane (PDMS)–based elastomeric rubbers Sylgard–184, SE1700, and an unfilled, end–linked model PDMS network are presented. The results of conventional ultrafast shock etalon measurements to time–of–flight measurements for similar thickness layers of irradiated and unirradiated SE1700 are compared. Here, good agreement between the shock response measured by these two ultrafast shock methods, as well as consistency between ultrafast data and long time scale gas gun data is found.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Review of the Effects of Polymer Binder Properties on Microstructure and Irreversible Volume Growth of Plastic Bonded Explosives Formulations

The rational design of effective polymeric binders for the formulation of plastic-bonded explosives (PBX) is challenging due to their inherent compositional complexity. The composites comprise irregularly shaped energetic material (EM) powders coated with low weight fractions of polymer via non-equilibrium processes such as slurry coating. Defects can deleteriously affect PBX stability and performance: nano- to micrometer-scale voids can act as loci for hot spots, lowering deflagration and detonation temperatures in unpredictable ways. Furthermore, some nominally desirable polymer properties are at odds with each other: e. g. good flow characteristics are desirable for coating and adhesion, but mechanical stiffness is needed to prevent deformation and cracking of PBX under mechanical stress. Good binder adhesion is critical, but the best means to predict and measure adhesion in PBX is not obvious. Experimental methods of determining binder adhesion on model surfaces may not capture polymer structural configurations relevant to deposition during coating. Molecular dynamics-based computational models have predicted key observables in PBX formulation, suggesting that they may be powerful tools for binder selection. In this review, primarily recent (~2006 and later) literature on polymeric binders for insensitive HE (IHE) is surveyed. We focus on how binder properties influence observable PBX properties as resistance to irreversible volume growth and void formation in PBX formulations mainly (but not exclusively) featuring 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the EM (e. g. PBX 9502, LX-17 and others). Conclusions from these studies yield useful guidelines for choosing HE binder candidates, as well as for the general design of highly-filled polymer composite materials. Finally, studies describing challenges in PBX formulation with the newer and more energetically dense high explosive, LLM-105, will be discussed.

adhesion↗
DOE OSTI2023

Layer-by-Layer-Processed Organic Solar Cells with 18.02% Efficiency Enabled by Regulating the Aggregation of Bottom Polymers

The fabrication of organic solar cells (OSCs) by a layer-by-layer (LBL) method has attracted growing attention in recent years. As already known, the pre-aggregates of conjugated polymers in solution have a profound impact on their microstructure morphology in films. Herein, by simply controlling the solution temperature and annealing processes, the pre-aggregation behavior of D18 polymer in solution can be fine-tuned and the microstructure of D18 bottom layer is well manipulated. The optimized D18 bottom layer can effectively regulate L8-BO upper-layer-forming suitable networks for efficient charge transportation. In addition, a vertical phase separation with a special D/D:A/A structure (P-i-N-type component distribution) is also formed. As a result, compared to the 16.43% power conversion efficiency (PCE) of the bulk heterojunction devices, such control enables bilayer OSC devices based on the polymer D18 and L8-BO to deliver an enhanced PCE of 18.02% with simultaneously improved short-circuit current density, open-circuit voltage, and fill factor. Importantly, it is also demonstrated in these results that the LBL deposition process utilizing the pre-aggregation of polymer and its fiber-network-forming ability is a very promising approach to improve charge dynamics, suppress carrier recombination, and fabricate highly efficient OSCs.

14 SOLAR ENERGY↗
DOE OSTI2018

Optical Properties of Amorphous Perfluorinated Polymers in the Terahertz Range

Novel amorphous perfluorinated polymers are synthesized and characterized using terahertz (THz) and x-ray spectra. The polymerization of such polymers in which all H atoms are replaced by F is examined. Their optical properties in the THz range show a record low index of refraction for solids in this range. The minimal possible index of refraction for such polymers is estimated. These materials are demonstrated to be highly transparent. The position of a weak absorption maximum in the range 1–2 THz is compared with the characteristic distance between the polymer structural elements that is obtained from an x-ray diffraction analysis of these materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗