Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle Size Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

CeO{sub 2} nanocrystals: Seed-mediated synthesis and size control

This work reports on seed-mediated synthesis and size control of monodispersed CeO{sub 2} nanoparticles. CeO{sub 2} nanoparticles of mean size smaller than 2 nm were first prepared by a simple mixing of aqueous solution of cerium (IV) sulfate and ammonia solution at ambient conditions. Using these as-prepared fine particles as the tiny seeds, tunable sizes of CeO{sub 2} nanoparticles were achieved via a facile hydrothermal treatment. All samples were characterized by X-ray diffraction (XRD), infrared (IR) spectroscopy, UV-vis spectroscopy, and thermogravimetric analysis (TGA). It is shown that in comparison with other inorganic cerium salts such as cerium (III) nitrates, cerium (IV) sulfate appears more suitable for forming CeO{sub 2} nanoparticles at room temperature. Sulfate groups are strongly thermodynamically adsorbed on CeO{sub 2} nanoparticle surfaces. The formation mechanism, surface hydration and sulfation characteristics of the resulting CeO{sub 2} nanoparticles are also discussed.

36 MATERIALS SCIENCE↗

Effect of cooling rate and Mg addition on the structural evaluation of rapidly solidified Al-20wt%Cu-12wt%Fe alloy

The present work examines the effect of Mg contents and cooling rate on the morphology and mechanical properties of Al{sub 20}Cu{sub 12}Fe quasicrystalline alloy. The microstructure of the alloys was analyzed by scanning electron microscopy and the phase composition was identified by X-ray diffractometry. The melting characteristics were studied by differential thermal analysis under an Ar atmosphere. The mechanical features of the melt-spun and conventionally solidified alloys were tested by tensile-strength test and Vickers micro-hardness test. It was found that the final microstructure of the Al{sub 20}Cu{sub 12}Fe samples mainly depends on the cooling rate and Mg contents, which suggests that different cooling rates and Mg contents produce different microstructures and properties. The average grain sizes of the melt spun samples were about 100–300 nm at 35 m/s. The nanosize, dispersed, different shaped quasicrystal particles possessed a remarkable effect to the mechanical characteristics of the rapidly solidified ribbons. The microhardness values of the melt spun samples were approximately 18% higher than those of the conventionally counterparts. - Highlights: •Quasicrystal-creating materials have high potential for applications. •Different shaped nanosize quasicrystal particles were observed. •The addition of Mg has an important impact on the mechanical properties. •H{sub V} values of the MS0, MS3 and MS5 samples at 35 m/s were 8.56, 8.66 and 8.80 GPa. •The volume fraction of IQC increases with increasing cooling rates.

36 MATERIALS SCIENCE↗

MICRO/NANO-STRUCTURAL EXAMINATION AND FISSION PRODUCT IDENTIFICATION IN NEUTRON IRRADIATED AGR-1 TRISO FUEL

Advanced microscopic and microanalysis techniques were developed and applied to study irradiation effects and fission product behavior in selected low-enriched uranium oxide/uranium carbide TRISO-coated particles from fuel compacts in six capsules irradiated to burnups of 11.2 to 19.6% FIMA. Although no TRISO coating failures were detected during the irradiation, the fraction of Ag-110m retained in individual particles often varied considerably within a single compact and at the capsule level. At the capsule level Ag-110m release fractions ranged from 1.2 to 38% and within a single compact, silver release from individual particles often spanned a range that extended from 100% retention to nearly 100% release. In this paper, selected irradiated particles from Baseline, Variant 1 and Variant 3 type fueled TRISO coated particles were examined using Scanning Electron Microscopy, Atom Probe Tomography; Electron Energy Loss Spectroscopy; Precession Electron Diffraction, Transmission Electron Microscopy, Scanning Transmission Electron Microscopy (STEM), High Resolution Electron Microscopy (HRTEM) examinations and Electron Probe Micro-Analyzer. Particle selection in this study allowed for comparison of the fission product distribution with Ag retention, fuel type and irradiation level. Nano sized Ag-containing features were predominantly identified in SiC grain boundaries and/or triple points in contrast with only two sitings of Ag inside a SiC grain in two different compacts (Baseline and Variant 3 fueled compacts). STEM and HRTEM analysis showed evidence of Ag and Pd co-existence in some cases and it was found that fission product precipitates can consist of multiple or single phases. STEM analysis also showed differences in precipitate compositions between Baseline and Variant 3 fuels. A higher density of fission product precipitate clusters were identified in the SiC layer in particles from the Variant 3 compact compared with the Variant 1 compact. Trend analysis shows precipitates were randomly distributed along the perimeter of the IPyC-SiC interlayer but only weakly associated with kernel protrusion and buffer fractures. There has been no evidence that the general release of silver is related to cracks or significant degradation of the microstructure. The results presented in this paper provide new insights to Ag transport mechanism(s) in intact SiC layer of TRISO coated particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TAUOLA update for decay channels with e + e – pairs in the final state

With the arrival of high luminosity B-factories like the Belle II experiment, τ decay measurements have become more precise than ever, allowing rarer processes to be explored, and finer details of τ decays to be studied. These are important to understand the spectrum of intermediate particles produced in τ decays. Therefore Monte Carlo generators, like the TAUOLA program, have to facilitate precision analysis as well as confront new models that constantly emerge with the availability of high statistics experimental data. New decay channels and models may lead to large variation of matrix elements size within the available phase space, as in the case when e + e - pairs are present in final state. It requires appropriate presampler of the phase space generator and a proper documentation to help users introduce their own models. While releasing a new update, it is important for the TAUOLA Monte Carlo library to maintain the general structure of the previous versions to preserve backward compatibility. The aim is to minimize changes from the user perspective. Finally, this paper presents a demonstration of new models implementation facilitated by the current update.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - FY2018 Final Report

High-value R2R processing is used to support a wide range of products in applications which span many industrial business sectors. The overall R2R process technology can be considered as “mature” as the process methodology and has been in use for decades. This continuous processing technique traditionally involves deposition of material(s) onto moving webs or carriers or other continuous R2R, belt-fed, or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Current process technologies, which typify “roll to roll”, include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multi-layer technologies can be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable by the general consumer. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches.Within the DOE EERE AMO, it was recognized that establishment of a program supported at the DOE National Laboratories, along with their immense design of materials and equipment modelling capabilities enabled with use of high-performance computing, could take advantage of available R2R infrastructure to manufacture new technologies. In FY 2016, a R2R Consortium was established and provided with initial “seed” funding to take an approach that was envisioned to be supportable by advanced manufacturing R2R processes. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy product development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this collaborative project would leverage the capabilities and expertise at each of four laboratories to further the development of an enabling high-volume cost-competitive platform technology. The collaboration team that is comprised of ORNL, ANL, NREL and LBNL, coordinating with EPB and other selected industry partners, was formed in April 2016 to initially address enhancing battery electrode performance and R2R manufacturing challenges. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; to evaluate mixed, active, particle size deposition and drying for novel electrode materials; to model various process condition changes and the resulting morphology and electrode performance; and to develop and validate NDE techniques for in-line measurement of battery electrode material properties. These efforts carried through FY 2017 and completed at the end of FY 2018.The approach was to look at compositions of materials with different particle sizes to make electrode samples using a R2R manufacturing process. The shape, size, and morphology of the materials, the chemistry of the formulation, the nature of slurries, their coating rate, the rate of drying all play a role in determining the final coating architecture, quality, and performance. A commercial cathode material was selected to make a series of cathodes and anodes by single pass, dual pass and slot die methods. Analysis of all the compiled results for this battery electrode development were that the best performing cathodes included: dual-pass electrode with large particles near the foil, mixed small and large particles, and small particles only. Whereas, the best performing anodes were with a mix of small and large graphite particles. An additional core project was added in FY 2017 to conduct studies of fuel cell materials that can be produced using R2R processes. The goal of this project is to explore, understand and optimize material and process parameters to support increased throughput, increased quality, and reduced cost for high volume production of gas-diffusion electrodes (GDEs) for PEMFCs. Project work in FY 2018 were to use a R2R process to fabricate electrodes without ionomer overlayer that can produce the equivalent mass activity as spray-coated electrodes with an ionomer overlayer. Oxygen-limiting current measurements were utilized to optimize oxygen mass transport. Alcohol-rich solvents were investigated, and results were that the alcohol and water ratio can be tuned to control ionomer distribution. Water-rich solvents produce a more dispersed ink which results in better high-current density performance.

36 MATERIALS SCIENCE↗

One Dimensional Analysis Model of a Condensing Spray Chamber Including Rocket Exhaust Using SINDA/FLUINT and CEA

Modeling droplet condensation via CFD codes can be very tedious, time consuming, and inaccurate. CFD codes may be tedious and time consuming in terms of using Lagrangian particle tracking approaches or particle sizing bins. Also since many codes ignore conduction through the droplet and or the degradating effect of heat and mass transfer if noncondensible species are present, the solutions may be inaccurate. The modeling of a condensing spray chamber where the significant size of the water droplets and the time and distance these droplets take to fall, can make the effect of droplet conduction a physical factor that needs to be considered in the model. Furthermore the presence of even a relatively small amount of noncondensible has been shown to reduce the amount of condensation. It is desirable then to create a modeling tool that addresses these issues. The path taken to create such a tool is illustrated. The application of this tool and subsequent results are based on the spray chamber in the Spacecraft Propulsion Research Facility (B2) located at NASA's Plum Brook Station that tested an RL-10 engine. The platform upon which the condensation physics is modeled is SINDAFLUINT. The use of SINDAFLUINT enables the ability to model various aspects of the entire testing facility, including the rocket exhaust duct flow and heat transfer to the exhaust duct wall. The ejector pumping system of the spray chamber is also easily implemented via SINDAFLUINT. The goal is to create a transient one dimensional flow and heat transfer model beginning at the rocket, continuing through the condensing spray chamber, and finally ending with the ejector pumping system. However the model of the condensing spray chamber may be run independently of the rocket and ejector systems detail, with only appropriate mass flow boundary conditions placed at the entrance and exit of the condensing spray chamber model. The model of the condensing spray chamber takes into account droplet conduction as well as the degrading effect of mass and heat transfer due to the presence of noncondensibles. The one dimension model of the condensing spray chamber makes no presupposition on the pressure profile within the chamber, allowing the implemented droplet physics of heat and mass transfer coupled to the SINDAFLUINT solver to determine a transient pressure profile of the condensing spray chamber. Model results compare well to the RL-10 engine pressure test data.

Chemical Equilibrium↗

One Dimensional Analysis Model of a Condensing Spray Chamber Including Rocket Exhaust Using SINDA/FLUINT and CEA

Modeling droplet condensation via CFD codes can be very tedious, time consuming, and inaccurate. CFD codes may be tedious and time consuming in terms of using Lagrangian particle tracking approaches or particle sizing bins. Also since many codes ignore conduction through the droplet and or the degradating effect of heat and mass transfer if noncondensible species are present, the solutions may be inaccurate. The modeling of a condensing spray chamber where the significant size of the water droplets and the time and distance these droplets take to fall, can make the effect of droplet conduction a physical factor that needs to be considered in the model. Furthermore the presence of even a relatively small amount of noncondensible has been shown to reduce the amount of condensation [Ref 1]. It is desirable then to create a modeling tool that addresses these issues. The path taken to create such a tool is illustrated. The application of this tool and subsequent results are based on the spray chamber in the Spacecraft Propulsion Research Facility (B2) located at NASA's Plum Brook Station that tested an RL-10 engine. The platform upon which the condensation physics is modeled is SINDAFLUINT. The use of SINDAFLUINT enables the ability to model various aspects of the entire testing facility, including the rocket exhaust duct flow and heat transfer to the exhaust duct wall. The ejector pumping system of the spray chamber is also easily implemented via SINDAFLUINT. The goal is to create a transient one dimensional flow and heat transfer model beginning at the rocket, continuing through the condensing spray chamber, and finally ending with the ejector pumping system. However the model of the condensing spray chamber may be run independently of the rocket and ejector systems detail, with only appropriate mass flow boundary conditions placed at the entrance and exit of the condensing spray chamber model. The model of the condensing spray chamber takes into account droplet conduction as well as the degrading effect of mass and heat transfer due to the presence of noncondensibles. The one dimension model of the condensing spray chamber makes no presupposition on the pressure profile within the chamber, allowing the implemented droplet physics of heat and mass transfer coupled to the SINDAFLUINT solver to determine a transient pressure profile of the condensing spray chamber. Model results compare well to the RL-10 engine pressure test data.

Condensing Spray Model↗

The Next Breakthroughs in Neutrino Physics (LDRD Final Report)

The neutrino is an important fundamental particle, one of the building blocks of the universe. Abetter understanding of the neutrino will answer questions regarding the origin of mass, the matter and anti-matter asymmetry of the universe, and the nature of dark matter. The nation's research community has recognized that the answers to these and other questions are within reach and has assigned neutrino experiments the highest priority for both nuclear and particle physics programs. We are investigating three aspects of neutrino experimentation: detection techniques, target materials, and data analysis. Our efforts targeted multiple applications including experiments to measure neutrinoless double-beta-decay, neutrino-oscillation and neutrino mass. Our research objectives include (1) developing approaches that make detectors scalable to larger sizes and insensitive to background signals; (2) increasing the signal strength and reducing noise from targets; and (3) efficiently distinguishing background noise from signals during analysis. In this LDRD we have advanced all of these areas. We have demonstrated the scale up of a metal organic framework that can adsorb xenon directly from the air that will allow for large neutrino detectors made from xenon. We have studied the use of Cherenkov radiation to reduce the signal backgrounds. We demonstrated the cracking of hydrogen to make atomic tritium for neutrino mass measurements, and lastly we demonstrated the benefits of machine learning techniques to improve signal to noise during analysis

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Aeolian abrasion on Venus: Preliminary results from the Venus simulator

The role of atmospheric pressure on aeolian abrasion was examined in the Venus Simulator with a constant temperature of 737 K. Both the rock target and the impactor were fine-grained basalt. The impactor was a 3 mm diameter angular particle chosen to represent a size of material that is entrainable by the dense Venusian atmosphere and potentially abrasive by virtue of its mass. It was projected at the target 10 to the 5 power times at a velocity of 0.7 m/s. The impactor showed a weight loss of approximately 1.2 x 10 to the -9 power gm per impact with the attrition occurring only at the edges. Results from scanning electron microscope analysis, profilometry, and weight measurement are summarized. It is concluded that particles can incur abrasion at Venusian temperatures even with low impact velocities expected for Venus.

Marshall, J. R.↗

Mechanisms of Retention and Transport of Fission Products in Virgin and Irradiated Nuclear Graphite

To fulfill the design and licensing requirements for advanced reactors, the U.S. Department of Energy (DOE) is specifically interested in targeted research to quantify the mechanisms of fission product transport and retention in graphitic grades that will likely be used in next-generation very/high temperature reactors, fluoride salt-cooled high temperature reactors and molten salt reactors. We have examined an integrated experimental-computational approach to determine the diffusivities of selected fission products – ruthenium (Ru) and silver (Ag) in five nuclear graphite grades – POCO AXF-5Q, POCO ZXF-5Q, PCEA, IG110, and NBG-18. Experimental investigation for diffusion of other fission products (iodine, cesium, and krypton) in graphite could not be carried out due to extreme evaporation due to high vapor pressure, despite several attempts incorporating various experimental schemes. Experimental investigation with irradiated graphite could not be carried out because necessary approval to transport irradiated graphite could not be obtained due to procedural reasons at ORNL and national policy change in UK. An effort was made to “produce” by ion sputtering, but it was discontinued because the outcome did not adequately represent irradiated graphite. Thin film and “cup-and-cap” methods were employed to deposit fission products, diffusion annealed were carried out in an argon atmosphere, and concentration profiles were determined by dynamic secondary ion mass spectroscopy depth profiling technique. Regardless of graphite type, anomalous diffusion behavior of Ru (i.e., lower than expected based on Arrhenius temperature dependence) at an intermediate temperature, around 600 to 700 °C, was observed. Diffusion behavior of silver on the other hand agreed well to the Arrhenius temperature dependence although the excessive evaporation of silver hampered the accurate determination of diffusivities at temperature higher than 900 °C. In general, silver was observed to diffuse faster than Ru in the temperature range compared from 500 to 900 °C, had consistently had higher pre-exponential factor corresponding to higher jump frequency. To understand the abnormal diffusional behavior of Ru in graphite in intermediate temperature range, a detailed microstructural analysis was carried out. Clustering of Ru into particles on the surface of graphite was observed around 700 °C corresponding to de-wetting and spheroidization. This change would influence the boundary condition of diffusion, although features of clustering was much smaller (<1 mm) than the SIMS raster size (120 x 120 mm). Raman spectroscopy also demonstrated that Raman peak intensity for Ru decreased significantly for samples annealed higher than 700 °C and presence of Ru in graphite altered the crystallinity of graphite. To further elucidate the abnormal diffusion behavior observed in intermediate temperature investigated, the vibrational properties of graphene, bilayer graphene and Kr atoms in bilayer graphene were investigated with molecular dynamics. Krypton, which is a fission product, was introduced between a bilayer graphene system to evaluate (i) whether the phonon dispersion curves change with high temperature in bilayer graphene (ii) whether the addition of Kr atoms between the bilayer introduces any significant change in the vibrational properties, and (iii) whether any change in the vibrational properties can be correlated to the diffusive behavior of Kr atoms. The results show that the Kr atoms indeed exhibit an anomalous diffusive behavior at 550°C. Phonon analysis shows that a few phonon frequencies are enhanced as much as 20 to 30 % with the addition of just 0.2 at.% Kr. So, this may explain the unexpected self-diffusivity of fission products.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Enzymantic Conversion of Coal to Liquid Fuels

The work in this project focused on the conversion of bituminous coal to liquid hydrocarbons. The major steps in this process include mechanical pretreatment, chemical pretreatment, and finally solubilization and conversion of coal to liquid hydrocarbons. Two different types of mechanical pretreatment were considered for the process: hammer mill grinding and jet mill grinding. After research and experimentation, it was decided to use jet mill grinding, which allows for coal to be ground down to particle sizes of 5 {mu}m or less. A Fluid Energy Model 0101 JET-O-MIZER-630 size reduction mill was purchased for this purpose. This machine was completed and final testing was performed on the machine at the Fluid Energy facilities in Telford, PA. The test results from the machine show that it can indeed perform to the required specifications and is able to grind coal down to a mean particle size that is ideal for experimentation. Solubilization and conversion experiments were performed on various pretreated coal samples using 3 different approaches: (1) enzymatic - using extracellular Laccase and Manganese Peroxidase (MnP), (2) chemical - using Ammonium Tartrate and Manganese Peroxidase, and (3) enzymatic - using the live organisms Phanerochaete chrysosporium. Spectral analysis was used to determine how effective each of these methods were in decomposing bituminous coal. After analysis of the results and other considerations, such as cost and environmental impacts, it was determined that the enzymatic approaches, as opposed to the chemical approaches using chelators, were more effective in decomposing coal. The results from the laccase/MnP experiments and Phanerochaete chrysosporium experiments are presented and compared in this final report. Spectra from both enzymatic methods show absorption peaks in the 240nm to 300nm region. These peaks correspond to aromatic intermediates formed when breaking down the coal structure. The peaks then decrease in absorbance over time, corresponding to the consumption of aromatic intermediates as they undergo ring cleavage. The results show that this process happens within 1 hour when using extracellular enzymes, but takes several days when using live organisms. In addition, live organisms require specific culture conditions, control of contaminants and fungicides in order to effectively produce extracellular enzymes that degrade coal. Therefore, when comparing the two enzymatic methods, results show that the process of using extracellular lignin degrading enzymes, such as laccase and manganese peroxidase, appears to be a more efficient method of decomposing bituminous coal.

01 COAL, LIGNITE, AND PEAT↗

Bioblendstocks to Optimize Mixing Controlled Compression Ignition (MCCI) Engines

In this project, a team of researchers from the University of Massachusetts Lowell, the University of Maine, and Mainstream Engineering developed an integrated process for the product of bioblendstocks to optimize mixing controlled compression ignition (MCCI) engines. The objective was to improve the energy density, sooting propensity, and cetane number of base diesel fuel while maintaining cold weather behavior. The process converts woody biomass (e.g. sawmill residues) into bio-oil through selective fast pyrolysis; the bio-oil is then selectively upgraded to form selectively oxygenated, minimally-branched hydrocarbons using non-noble metal catalysts in combination with metal-catalyzed hydrogenation. Advanced predictive models, in conjunction with existing property databases, and experimental testing are used to evaluate overall bioblendstock properties and their impact on base diesel fuel. An iterative, targeted upgrading approach was implemented to optimize the proposed bioblendstock’s properties. Assessment methodologies included techno-economic analysis, life-cycle assessment, property testing, and engine testing. Ultimately, the project team successfully produced a viable bioblendstock while identifying critical process points related to scale-up efforts. It was found that producing pyrolysis oils at 500 degrees C and with pine particle sizes of 1-2 mm led to bio-oil with a higher yield (of approximately 45 wt%) and rich amounts of aromatic alcohols. The resultant pyrolysis oil was then upgraded using a sequence of mild hydrotreating, followed by catalytic etherification and esterification, followed by another final mild hydrotreating to produce a blendstock containing saturated species with a limited, but non-zero, amount of oxygen. The aromatic alcohols produced by pyrolysis were especially helpful in this regard, as the resulting bicycloethers and derivatives exhibited high cetane numbers. While most bulk properties of the bioblendstock met or exceeded targeted thresholds, viscosity and cloud point notably fell outside the expected range; this could be addressed by blending limits and/or through the use of additives that are commonplace in current refinding practices. Identification of a bioblendstock that can be produced economically at scale while improving the performance and emissions characteristics of internal combustion engines positively affects the economy by boosting domestic fuel production and the environment by decreasing harmful emissions and increasing efficiency.

09 BIOMASS FUELS↗

Aerosol Formation from High-Pressure Sprays for Supporting the Safety Analysis for the Hanford Waste Treatment and Immobilization Plant - 13183

The Waste Treatment and Immobilization Plant (WTP) at Hanford is being designed and built to pretreat and vitrify waste currently stored in underground tanks at Hanford. One of the postulated events in the hazard analysis for the WTP is a breach in process piping that produces a pressurized spray with small droplets that can be transported into ventilation systems. Literature correlations are currently used for estimating the generation rate and size distribution of aerosol droplets in postulated releases. These correlations, however, are based on results obtained from small engineered nozzles using Newtonian liquids that do not contain slurry particles and thus do not represent the fluids and breaches in the WTP. A test program was developed to measure the generation rate, and the release fraction which is the ratio of generation rate to spray flow rate, of droplets suspended in a test chamber and droplet size distribution from prototypic sprays. A novel test method was developed to allow measurement of sprays from small to large breaches and also includes the effect of aerosol generation from splatter when the spray impacts on walls. Results show that the release fraction decreases with increasing orifice area, though with a weaker dependence on orifice area than the currently-used correlation. A comparison of water sprays to slurry sprays with 8 to 20 wt% gibbsite or boehmite particles shows that the presence of slurry particles depresses the release fraction compared to water for droplets above 10 μm and increases the release fraction below this droplet size. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Novel Approaches to Cellular Transplantation from the US Space Program

Research in the treatment of type I diabetes is entering a new era that takes advantage of our knowledge in an ever increasing variety of scientific disciplines. Some may originate from very diverse sources, one of which is the Space Program at National Aeronautics and Space Administration (NASA). The Space Program contributes to diabetes-related research in several treatment modalities. As an ongoing effort for medical monitoring of personnel involved in space exploration activities NASA and the extramural scientific community investigate strategies for noninvasive estimation of blood glucose levels. Part of the effort in the space protein crystal growth program is high-resolution structural analysis insulin as a means to better understand the interaction with its receptor and with host immune components and as a basis for rational design of a "better" insulin molecule. The Space Program is also developing laser technology for potential early cataract detection as well as a noninvasive analyses for addressing preclinical diabetic retinopathy. Finally, NASA developed an exciting cell culture system that affords some unique advantages in the propagation and maintenance of mammalian cells in vitro. The cell culture system was originally designed to maintain cell suspensions with a minimum of hydrodynamic and mechanical sheer while awaiting launch into microgravity. Currently the commercially available NASA bioreactor (Synthecon, Inc., Houston, TX) is used as a research tool in basic and applied cell biology. In recent years there is continued strong interest in cellular transplantation as treatment for type I diabetes. The advantages are the potential for successful long-term amelioration and a minimum risk for morbidity in the event of rejection of the transplanted cells. The pathway to successful application of this strategy is accompanied by several substantial hurdles: (1) isolation and propagation of a suitable uniform donor cell population; (2) management of host immune rejection; (3) protection from the autoimmune component of the disease; and (4) anatomic placement of the engrafted cells that permits timely response to blood sugar levels as well as effective release and deployment of insulin. Bioreactor technology may provide some critical advances for surmounting some of these scientific hurdles. The NASA bioreactor is a horizontally rotating cylinder that is completely filled with culture medium. Gaseous exchange is maintained by a concentric cylinder of permeable silicon. In slow rotation (15-25 rpm) particles of small mass such as cells and tissue aggregates remain suspended in the rotating body of fluid. This novel approach suspends cells without stirring thus, allowing objects of different size mass to colocate and interact in a very low shear environment. In fact, analysis of the forces acting on individual cells in the rotating bioreactor reveals that the cells are continuously falling through the fluid medium. The conditions in the bioreactor permit assembly of cells into aggregates. three-dimensional tissue growth, synthesis of intercellular matrix,10 differentiation, and some sinusoid formations that may serve as a surrogate vasculature for larger tissue segments.

Pellis, Neal R.↗

Electromagnetic diagnostic techniques for hypervelocity projectile detection, velocity measurement, and size characterization: Theoretical concept and first experimental test

A new measurement technique is suggested to augment the characterization and understanding of hypervelocity projectiles before impact. The electromagnetic technique utilizes magnetic diffusion principles to detect particles, measure velocity, and indicate relative particle dimensions. It is particularly suited for detection of small particles that may be difficult to track utilizing current characterization methods, such as high-speed video or flash radiography but can be readily used for large particle detection, where particle spacing or location is not practical for other measurement systems. In this work, particles down to 2 mm in diameter have been characterized while focusing on confining the detection signal to enable multi-particle characterization with limited particle-to-particle spacing. The focus of the paper is on the theoretical concept and the analysis of its applicability based on analytical and numerical calculation. First proof-of-principle experimental tests serve to further validate the method. Some potential applications are the characterization of particles from a shaped-charge jet after its break-up and investigating debris in impact experiments to test theoretical models for the distribution of particles size, number, and velocity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser-dust interaction and dust size distribution measurements on DIII-D

The determination of dust radius distributions from the measurement of laser scattering intensity in tokamaks is presented. The analysis takes into account non-Rayleigh regimes of light scattering for different complex refractive indices of dust materials, as well as dust evaporation due to heating by laser radiation. The model is applied to calculate the dust particle radius distribution in tokamaks during normal plasma operation. It is shown that a relatively small amount of large dust particles in the distribution may play a significant role for estimation of the dust mass inventory in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The magnetic and neutron diffraction studies of La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles prepared via molten salt synthesis

Series of single-phase La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles (x=0.25−0.47) with the size of about 50 nm was prepared in molten NaNO{sub 2}. TEM evidenced well dispersed particles that are not interconnected by sintering bridges in contrast to traditional products. Interestingly, some reduction of the perovskite cell volume, particularly at higher Sr-contents, was detected by XRD. Moreover, reduced magnetization and decreased Curie temperature in comparison to sol–gel samples were observed. Neutron diffraction analysis of the as-prepared nanoparticles and several comparative samples with x=0.37 indicated that the anomalous behavior of studied particles probably originate in the overdoped outer shell. The overdoping might result from both the surface oxygen chemisorption and from an increased Sr concentration in the shell. By all means, the overdoping would lead to compressive surface stress, driving the x=0.37 ground state toward a mixture of FM and A-type AFM ordering as observed by neutron diffraction. - Graphical abstract: La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles with the size of about 50 nm were prepared by newly established method in molten NaNO{sub 2}. TEM proved the formation of well-separated particles without sintering bridges, the major advantage over traditional preparation methods. - Highlights: • Series of La{sub 1−x}Sr{sub x}MnO{sub 3} nanoparticles was prepared by novel method in NaNO{sub 2} melt. • Lower magnetization and Curie temperature in comparison to sol–gel nanoparticles was observed. • Overdoping of outer shell was indicated by neutron diffraction and cerimetric titration. • Overdoping shifts La{sub 0.37}Sr{sub 0.63}MnO{sub 3} ground state to a mixture of FM and A-type AFM ordering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗