Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Tuned and screened range-separated hybrid density functional theory for describing electronic and optical properties of defective gallium nitride

We apply a hybrid density functional theory approach, based on a tuned and screened range-separated hybrid (SRSH) exchange-correlation functional, to describe the optoelectronic properties of defective gallium nitride (GaN). SRSH and time-dependent SRSH (TDSRSH) are tuned to produce accurate energetics for the pristine material and applied to the study of a series of point defects in bulk GaN, a blue light-emitting material that degrades in the presence of defects. We first establish the accuracy of the method by comparing the predicted quasiparticle gap and low-energy excitation spectra of (TD)SRSH and many-body perturbation theory for both pristine GaN and GaN containing a single nitrogen vacancy. Aided by the reduced computational cost of (TD)SRSH, we then report on three additional technologically relevant point defects and defect complexes in GaN: the gallium vacancy, the carbon interstitial, and the carbon-silicon complex. We compute the low-energy optical absorption spectra for these defects and show the presence of defect-centered transitions. Furthermore, by estimating the Stokes shift, we predict, in agreement with previous studies, that the carbon substitutional defect is a candidate for the detrimental yellow luminescence in GaN. Furthermore, this study indicates that TDSRSH is a promising and computationally feasible approach for quantitatively accurate, first-principles modeling of defective semiconductors.

36 MATERIALS SCIENCE↗

Nonlinear optical properties of bulk cuprous oxide using single beam Z-scan at 790 nm

The two-photon absorption (TPA) coefficient β and the nonlinear index of refraction n{sub 2} for bulk cuprous oxide (Cu{sub 2}O) direct gap semiconductor single crystal have been measured by using a balance-detection Z-scan single beam technique, with an excellent signal to noise ratio. Both coefficients were measured at 790 nm using a 65 fs laser pulse at a repetition rate of 90.9 MHz, generated by a Ti:Sapphire laser oscillator. The experimental values for β were explained by using a model that includes allowed-allowed, forbidden-allowed, and forbidden-forbidden transitions. It was found that the forbidden-forbidden transition is the dominant mechanism, which is consistent with the band structure of Cu{sub 2}O. The low value for β found in bulk, as compared with respect to thin film, is explained in terms of the structural change in thin films that result in opposite parities of the conduction and valence band. The n{sub 2} is also theoretically calculated by using the TPA dispersion curve and the Kramers-Kronig relations for nonlinear optics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Synthesis, crystal and electronic structures, linear and nonlinear optical properties, and photocurrent response of oxyhalides CeHaVIO 4 (Ha = Cl, Br; VI = Mo, W)

Four heteroanionic oxyhalides, CeClMoO 4 , CeBrMoO 4 , CeClWO 4 , and CeBrWO 4 , have been studied as multifunctional materials, which show a combination of good second harmonic generation (SHG) response and photocurrent signals. Millimeter-sized CeHaVIO 4 (Ha = Cl, Br; VI = Mo, W) crystals were grown by halide salt flux. The crystal structure of CeHaVIO 4 crystals was accurately determined by single-crystal X-ray diffraction. CeClMoO 4 , CeBrMoO 4 , and CeBrWO 4 are isostructural to each other, and crystallize in the acentric LaBrMoO 4 structure type. CeClWO 4 crystallizes in a new structure type with unit cell parameters of a = 19.6059(2) Å, b = 5.89450(10) Å, c = 7.80090(10) Å, and β = 101.4746(8)°. The bandgaps of CeHaVIO 4 fall into the range of 2.8(1)–3.1(1) eV, which are much smaller than those of isotypic LaHaVIO 4 (Ha = Cl, Br; VI = Mo, W) in the range of 3.9(1)–4.3(1) eV. The narrowing of bandgaps in CeHaVIO 4 originates from the presence of partially filled 4f orbitals of cerium atoms, which was confirmed by density functional theory (DFT) calculations. The moderate bandgaps make CeHaVIO 4 suitable for infrared nonlinear optical (IR NLO) applications. CeBrMoO 4 and CeBrWO 4 exhibit moderate SHG responses of 0.58× AGS and 0.46× AGS, respectively, and are both type-I phase-matching materials. Moderate SHG response, easy growth of crystals, high ambient stability, and type-I phase-matching behavior make CeBrMoO 4 and CeBrWO 4 great materials for IR NLO applications. CeHaVIO 4 films also exhibited good photocurrent response upon light radiation. Furthermore, this work demonstrates the rich structural chemistry of the REHaVIO 4 (RE = Y, La–Lu; Ha = Cl, Br; VI = Mo, W) family and the potential presence of more multifunctional materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Controlling surface adatom kinetics for improved structural and optical properties of high indium content aluminum indium nitride

A non-traditional, for AlInN, method of controlling adatom kinetics and a low temperature growth condition were employed to improve the quality of high indium content aluminum indium nitride films. Metal-rich surfaces were used to enhance adatom mobility and compensate for the low growth temperature (Tsub ≤ 400 °C) effect of reducing surface diffusion lengths. The metal-rich approach resulted in 12 times lower x-ray diffraction full-width at half-maximum rocking curve figures of merit when compared to literature. In addition to promising photoluminescence emission, these results indicate improved structural quality over other reported approaches. AlInN films with ∼70% indium content were characterized via x-ray diffraction, atomic force microscopy, and photoluminescence spectroscopy with each technique indicating an optimal growth temperature of 350 °C. Al0.3In0.7N grown above 400 °C exhibited phase separation and a reduction in quality, while samples grown colder were predominantly single-phase and displayed improved photoluminescence at ∼1.45 eV. The photoluminescence spectra suggest emission from quantum wire-like structures with dimensions ranging from 15 to 18 nm. These low-temperature, metal-rich findings for high indium content AlInN are promising for future long-wavelength III-nitride optical devices.

Engel, Zachary (ORCID:0000000205021981)↗

Physical and optical properties of Co{sup 2+}, Ni{sup 2+} doped 20ZnO + xLi{sub 2}O + (30 − x)K{sub 2}O + 50B{sub 2}O{sub 3} (5 ≤ x ≤ 25) glasses: Observation of mixed alkali effect

Graphical abstract: Composition dependence of density and Urbach energy of Co{sup 2+} and Ni{sup 2+} doped ZLKB glasses: (a) Co{sup 2+} doped glasses and (b) Ni{sup 2+} doped glasses. Both are exhibited mixed alkali effect. Highlights: ► Mixed alkali effect is observed. ► Band gap studies indicate that the glasses are structural stable. ► The glasses are observed to be partially covalent in nature. -- Abstract: Co{sup 2+} and Ni{sup 2+} ions doped 20ZnO + xLi{sub 2}O + (30 − x) K{sub 2}O + 50B{sub 2}O{sub 3} (5 ≤ x ≤ 25) mol% glasses are prepared using melt quenching technique. Structural changes of the prepared glasses by addition of transition metal oxides, CoO and NiO are investigated by UV–vis–NIR, FT-IR spectroscopy and XRD. The XRD pattern indicates the amorphous nature of prepared glasses. FT-IR measurements of the all glasses revealed that the network structure of the glasses are mainly based on BO{sub 3} and BO{sub 4} units placed in different structural groups in which the BO{sub 3} units being dominant. The optical absorption spectra suggest the site symmetry of Co{sup 2+} and Ni{sup 2+} ions in the glasses are near octahedral. Crystal field and inter-electronic repulsion parameters are also evaluated. The optical band gap and Urbach energies exhibited the mixed alkali effect. Various physical parameters such as density, refractive index, optical dielectric constant, polaron radius, electronic polarizability and inter-ionic distance are also determined.

36 MATERIALS SCIENCE↗

Measurement and Modeling of Vertically Resolved Aerosol Optical Properties and Radiative Fluxes Over the ARM SGP Site

In order to meet one of its goals - to relate observations of radiative fluxes and radiances to the atmospheric composition - the Department of Energy's Atmospheric Radiation Measurement (ARM) program has pursued measurements and modeling activities that attempt to determine how aerosols impact atmospheric radiative transfer, both directly and indirectly. However, significant discrepancies between aerosol properties measured in situ or remotely remain. One of the objectives of the Aerosol Intensive Operational Period (TOP) conducted by ARM in May 2003 at the ARM Southern Great Plains (SGP) site in north central Oklahoma was to examine and hopefully reduce these differences. The IOP involved airborne measurements from two airplanes over the heavily instrumented SGP site. We give an overview of airborne results obtained aboard the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) Twin Otter aircraft. The Twin Otter performed 16 research flights over the SGP site. The aircraft carried instrumentation to perform in-situ measurements of aerosol absorption, scattering, extinction and particle size. This included such novel techniques as the photoacoustic and cavity ring-down methods for in-situ absorption (675 nm) and extinction (675 and 1550 nm) and a new multiwavelength, filter-based absorption photometer (467, 530, 660 nm). A newly developed instrument measured cloud condensation nucleus concentration (CCN) concentrations at two supersaturation levels. Aerosol optical depth and extinction (354-2139 nm) were measured with the NASA Ames Airborne Tracking 14-channel sunphotometer. Furthermore, up-and downwelling solar (broadband and spectral) and infrared radiation were measured using seven individual radiometers. Three up-looking radiometers werer mounted on a newly developed stabilized platform, keeping the instruments level up to aircraft pitch and roll angles of approximately 10(exp 0). This resulted in unprecedented continuous vertical profiles of radiative fluxes, which we will compare to modeled fluxes using the aforementioned data as input.

Schmid, B.↗

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

Enhanced Far Ultra-Violet Optical Properties of Physical Vapor Deposited Aluminum Mirrors Through Fluorination

Astronomical instrumentation for measurements in the Far Ultra-Violet (FUV, 90-200 nm) typically use aluminum (Al) thin films due to their high reflectance over this wavelength range. However, the native aluminum oxide layer that forms on Al upon exposure to the atmosphere is strongly absorbing in this wavelength range, requiring that the films be protected with a dielectric that inhibits oxidation. Typically, magnesium fluoride (MgF 2 ) or lithium fluoride (LiF) coatings are used as protective layers, but each has shortcomings. For example, MgF 2 has an absorption cutoff at 115 nm reducing performance in a critical part of the FUV spectrum of observational interest. A viable option to access these lower wavelengths could be the use of the LiF overcoat as it has a lower absorption cutoff at 102.5 nm, but it is hygroscopic and thus susceptible to degradation in humid conditions. An approach to reduce the hygroscopic nature of LiF would be to implement a passivation process during the deposition of both Al+LiF coatings. Our team at GSFC has developed a new reactive Physical Vapor Deposition (rPVD) process that consists of a fluorination process with XeF 2 gas combined with our traditional PVD process. We have found that this new rPVD coating process offers a protected version of Al+LiF with a more environmentally stable and more transparent LiF layer, along with unprecedent reflectivity. The process starts with a bare optically smooth substrate that is coated with Al in an ultra-high vacuum (UHV) chamber by the conventional PVD process. Then, the bare Al mirror is immediately exposed to a reactive XeF 2 gas before and after the application of the flash PVD evaporated LiF layer. We have also been investigating the use of this rPVD coating process for potential efficiency enhancements of Si-based gratings. Since it is known that the XeF 2 vapor is a strong Si etchant, we are investigating if the native SiO 2 layer on Si is sufficient to protect the groove profile of e-beam-ruled Si gratings from degradation. We will report on the characterization of various Al+LiF witness mirror coatings (both on borosilicate and Si) performed under various deposition conditions using the XeF 2 passivation process. These tests include XPS to determine film stoichiometry and AFM/SEM to measure surface roughness and any etching on the Si substrate. We will also report on FUV reflectance and spectroscopic ellipsometry to characterize optical constants of these passivated films in the UV/Visible/NIR spectral ranges.

Engineering (General)↗

Electronic and Optical Properties of VSc 2 N@C 68 Fullerene

Here, we report a detailed investigation of structural, electronic, and spectroscopic properties of VSc 2 N@C 68 endohedral fullerene. First, the candidate structures of the ground state are obtained using a systematic approach in which 900 isomers of endohedral fullerenes were screened for their energetic stability. The stability of some of the most promising isomers was studied using density functional theory at the all-electron level using large polarized Gaussian basis sets. Although the dopant vanadium atom is also in the same charge state as Sc, the doping changes the structure and the spin state from that of Sc 3 N@C 68 . The d-orbitals of the V atom lead to a spin state with spin moment of 2 μ B for the endohedral fullerene. The spin–orbit coupling strength is, however, weak, leading to vanishingly small zero-field splitting of the spin levels. The ionization energy, electron affinity, and the quasi-particle gap of the most stable isomer are comparable to those of C 60 . The vibrational frequency analysis shows that the structure is stable. Finally, the infrared, Raman, and optical spectra of the most stable fullerene are calculated, which can aid in identification of the cluster in experiments.

36 MATERIALS SCIENCE↗

Small-Scale Drop Size Variability: Impact on Estimation of Cloud Optical Properties

Most cloud radiation models and conventional data processing techniques assume that the mean number of drops of a given radius is proportional to volume. The analysis of microphysical data on liquid water drop sizes shows that, for sufficiently small volumes, this proportionality breaks down; the number of cloud drops of a given radius is instead proportional to the volume raised to a drop size-dependent nonunit power. The coefficient of proportionality, a generalized drop concentration, is a function of the drop size. For abundant small drops the power is unity as assumed in the conventional approach. However, for rarer large drops, it falls increasingly below unity. This empirical fact leads to drop clustering, with the larger drops exhibiting a greater degree of clustering. The generalized drop concentration shows the mean number of drops per cluster, while the power characterizes the occurrence frequency of clusters. With a fixed total number of drops in a cloud, a decrease in frequency of clusters is accompanied by a corresponding increase in the generalized concentration. This initiates a competing process missed in the conventional models: an increase in the number of drops per cluster enhances the impact of rarer large drops on cloud radiation while a decrease in the frequency suppresses it. Because of the nonlinear relationship between the number of clustered drops and the volume, these two opposite tendencies do not necessarily compensate each other. The data analysis suggests that clustered drops likely have a stronger radiative impact compared to their unclustered counterpart; ignoring it results in underestimation of the contribution from large drops to cloud horizontal optical path.

Knyazikhin, Y.↗

Validation of Surface Bio-Optical Properties in the Gulf of Maine as a Means for Improving Satellite Primary Production Estimates

One of the greatest challenges in providing sea-truth data for various ocean color sensors is climatology. This is particularly true in the Gulf of Maine since it is cloudy and foggy more than it is clear; the climatology shows on average, about one in four to five days has clear skies with clear days slightly more frequent in the late summer and early fall. Our strategy has been to use a ship of opportunity where one has choice of the sampling days. This provides much better flexibility to sample during clear periods with good satellite coverage. Our Sensor Intercomparison and Merger for Biological and Interdisciplinary Oceanic Studies (SIMBIOS) contract has been to use the M/S Scotia Prince ferry as a ship of opportunity, running between Portland, Maine and Yarmouth, NS. Measurements include continuous, surface, along-track fluorescence, two independent measures of backscattering, total light scattering, absorption, beam attenuation, above-water remote sensing reflectance, calcite-dependent light scattering, temperature, and salinity. Expendable bathythermography (XBT) drops allow acquisition of vertical temperature information, useful for defining isopycnal slope, which affects primary production. These data are comparable to a previous program from early 1982, where a ship of opportunity program (SOOP) was run on the truck ferry, M/V Marine Evangeline, which ran along the same transect. These surface data were combined with satellite-derived sea surface temperature fields to examine the Maine coastal current. Unfortunately, this program stopped in 1982. The ongoing SIMBIOS results will dovetail nicely with the previous work (which also had Coastal Zone Color Scanner (CZCS) coverage) for looking at any long-term changes in the Gulf of Maine hydrography, bio-optics, and biogeochemistry.

Balch, William M.↗

Optical properties and carrier dynamics of GaAs/GaInAs multiple-quantum-well shell grown on GaAs nanowire by molecular beam epitaxy

GaAs/GaInAs multiple-quantum-well (MQW) shells having different GaInAs shell width formed on the surface of self-catalyzed GaAs core nanowires (NWs) are grown on (100) Si substrate using molecular beam epitaxy. The photoluminescence emission from GaAs/GaInAs MQW shells and the carrier lifetime could be varied by changing the width of GaInAs shell. Time-resolved photoluminescence measurements showed that the carrier lifetime had a fast and slow decay owing to the mixing of wurtzite and zinc-blende structures of the NWs. Furthermore, strain relaxation caused the carrier lifetime to decrease beyond a certain thickness of GaInAs quantum well shells.

14 SOLAR ENERGY↗

Effect of Cobalt Oxide Nanoparticles on the Nano-scale Free Volume and Optical Properties of Biodegradable CMC/PVA Films

Chemically prepared cobalt oxide nanoparticles (NPs) were added to biodegradable carboxymethyl cellulose (CMC) (20%)/polyvinyl alcohol (PVA) (80%) blend films. The structural properties of these films were investigated by X-ray diffraction, Fourier transformation infrared spectroscopy (FTIR) and differential thermal analysis (DTA). Co{sub 3}O{sub 4}/(CMC + PVA) films show a semi-crystalline structure and the degree of crystallinity decreases with adding Co{sub 3}O{sub 4} NPs. FTIR confirms the good interaction between the blend chains and Co{sub 3}O{sub 4} NPs. The melting temperature T{sub m} for CMC/PVA is about 212 °C then decreased with increasing Co{sub 3}O{sub 4} content, due to some decrease in the ordered association of the blend which results in a decrease in the blend crystallinity. Positron annihilation lifetime spectroscopy (PALS) measurements were carried out with a conventional fast–fast coincidence spectrometer. It was found that ortho-positronium lifetime τ{sub 3} and free volume V{sub f} increase while o-Ps intensity I{sub 3} still constant as Co{sub 3}O{sub 4} concentration increases. This is because adding Co{sub 3}O{sub 4} NPs encourages the formation of o-Ps. The swelling ratio SR% as a function of Co{sub 3}O{sub 4} concentration was also studied and its value increases with Co{sub 3}O{sub 4} addition. The optical study illustrated the decrease of the transmittance T of the films from 87 to 35.5% with increasing Co{sub 3}O{sub 4} content from 0 to 0.9 wt%. Also, both the direct and indirect optical band gaps of the films red-shifted from 4.05 to 3.75 eV and 3.3 to 2.75 eV, respectively. The influence of Co{sub 3}O{sub 4} on the refractive index of the films is also reported.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Vertical Structure and Optical Properties of Titans Aerosols from Radiance Measurements Made Inside and Outside the Atmosphere

Prompted by the detection of stratospheric cloud layers by Cassini's Composite Infrared Spectrometer (CIRS; see Anderson, C.M., Samuelson, R.E. [2011]. Icarus 212, 762-778), we have re-examined the observations made by the Descent Imager/Spectral Radiometer (DISR) in the atmosphere of Titan together with two constraints from measurements made outside the atmosphere. No evidence of thin layers (<1 km) in the DISR image data sets is seen beyond the three previously reported layers at 21 km, 11 km, and 7 km by Karkoschka and Tomasko (Karkoschka, E., Tomasko, M.G. [2009]. Icarus 199, 442-448). On the other hand, there is evidence of a thicker layer centered at about 55 km. A rise in radiance gradients in the Downward-Looking Visible Spectrometer (DLVS) data below 55 km indicates an increase in the volume extinction coefficient near this altitude. To fit the geometric albedo measured from outside the atmosphere the decrease in the single scattering albedo of Titan's aerosols at high altitudes, noted in earlier studies of DISR data, must continue to much higher altitudes. The altitude of Titan's limb as a function of wavelength requires that the scale height of the aerosols decrease with altitude from the 65 km value seen in the DISR observations below 140 km to the 45 km value at higher altitudes. We compared the variation of radiance with nadir angle observed in the DISR images to improve our aerosol model. Our new aerosol model fits the altitude and wavelength variations of the observations at small and intermediate nadir angles but not for large nadir angles, indicating an effect that is not reproduced by our radiative transfer model. The volume extinction profiles are modeled by continuous functions except near the enhancement level near 55 km altitude. The wavelength dependence of the extinction optical depth is similar to earlier results at wavelengths from 500 to 700 nm, but is smaller at shorter wavelengths and larger toward longer wavelengths. A Hapke-like model is used for the ground reflectivity, and the variation of the Hapke single scattering albedo with wavelength is given. Fits to the visible spectrometers looking upward and downward are achieved except in the methane bands longward of 720 nm. This is possibly due to uncertainties in extrapolation of laboratory measurements from 1 km-am paths to much longer paths at lower pressures. It could also be due to changes in the single scattering phase functions at low altitudes, which strongly affect the path length through methane that the photons travel. We demonstrate the effects on the model fits by varying each model parameter individually in order to illustrate the sensitivity of our determination of each model parameter.

Titan↗

Large Contribution of Coarse Mode to Aerosol Microphysical and Optical Properties: Evidence from Ground-Based Observations of a Transpacific Dust Outbreak at a High-Elevation North American Site

This work is motivated by previous studies of transatlantic transport of Saharan dust and the observed quasi-static nature of coarse mode aerosol with a volume median diameter (VMD) of approximately 3.5 μm. The authors examine coarse mode contributions from transpacific transport of dust to North American aerosol properties using a dataset collected at the high-elevation Storm Peak Laboratory (SPL) and the nearby Atmospheric Radiation Measurement (ARM) Mobile Facility. Collected ground-based data are complemented by quasi-global model simulations and satellite and ground-based observations. The authors identify a major dust event associated mostly with a transpacific plume (about 65% of near-surface aerosol mass) in which the coarse mode with moderate (~3 μm) VMD is distinct and contributes substantially to total aerosol volume (up to 70%) and scattering (up to 40%). The results demonstrate that the identified plume at the SPL site has a considerable fraction of supermicron particles (VMD ~3 μm) and, thus, suggest that these particles have a fairly invariant behavior despite transpacific transport. If confirmed in additional studies, this invariant behavior may simplify considerably parameterizations for size-dependent processes associated with dust transport and removal.

54 ENVIRONMENTAL SCIENCES↗

Multifunctional Cu 2 TSiS 4 (T = Mn and Fe): Polar Semiconducting Antiferromagnets with Nonlinear Optical Properties

In this work, Cu 2 TSiS 4 (T = Mn and Fe) polycrystalline and single-crystal materials were prepared with high-temperature solid-state and chemical vapor transport methods, respectively. The polar crystal structure (space group Pmn2 1 ) consists of chains of corner-sharing and distorted CuS 4 , Mn/FeS 4 , and SiS 4 tetrahedra, which is confirmed by Rietveld refinement using neutron powder diffraction data, X-ray single-crystal refinement, electron diffraction, energy-dispersive X-ray spectroscopy, and second harmonic generation (SHG) techniques. Magnetic measurements indicate that both compounds order antiferromagnetically at 8 and 14 K, respectively, which is supported by the temperature-dependent (100–2 K) neutron powder diffraction data. Additional magnetic reflections observed at 2 K can be modeled by magnetic propagation vectors k = (1/2,0,1/2) and k = (1/2,1/2,1/2) for Cu 2 MnSiS 4 and Cu 2 FeSiS 4 , respectively. The refined antiferromagnetic structure reveals that the Mn/Fe spins are canted away from the ac plane by about 14°, with the total magnetic moments of Mn and Fe being 4.1(1) and 2.9(1) μ B , respectively. Both compounds exhibit an SHG response with relatively modest second-order nonlinear susceptibilities. Density functional theory calculations are used to describe the electronic band structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Morphology and mixing state of aged soot particles at a remote marine free troposphere site: Implications for optical properties

The radiative properties of soot particles depend on their morphology and mixing state, but their evolution during transport is still elusive. In this paper, we report observations from an electron microscopy analysis of individual particles transported in the free troposphere over long distances to the remote Pico Mountain Observatory in the Azores in the North Atlantic. Approximately 70% of the soot particles were highly compact and of those 26% were thinly coated. Discrete dipole approximation simulations indicate that this compaction results in an increase in soot single scattering albedo by a factor of ≤2.17. The top of the atmosphere direct radiative forcing is typically smaller for highly compact than mass-equivalent lacy soot. Lastly, the forcing estimated using Mie theory is within 12% of the forcing estimated using the discrete dipole approximation for a high surface albedo, implying that Mie calculations may provide a reasonable approximation for compact soot above remote marine clouds.

54 ENVIRONMENTAL SCIENCES↗