Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NEUTRON SCIENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Delayed neutron fraction and prompt decay constant measurement in the MINERVE reactor using the PSI instrumentation

The critical decay constant (B/A), delayed neutron fraction (B) and generation time (A) of the Minerve reactor were measured by the Paul Scherrer Institut (PSI) and the Commissariat a l'Energie Atomique (CEA) in September 2014 using the Feynman-alpha and Power Spectral Density neutron noise measurement techniques. Three slightly subcritical configuration were measured using two 1-g {sup 235}U fission chambers. This paper reports on the results obtained by PSI in the near critical configuration (-2g). The most reliable and precise results were obtained with the Cross-Power Spectral Density technique: B = 708.4±9.2 pcm, B/A = 79.0±0.6 s{sup -1} and A 89.7±1.4 micros. Predictions of the same kinetic parameters were obtained with MCNP5-v1.6 and the JEFF-3.1 and ENDF/B-VII.1 nuclear data libraries. On average the predictions for B and B/A overestimate the experimental results by 5% and 11%, respectively. The discrepancy is suspected to come from either a corruption of the data or from the inadequacy of the point kinetic equations to interpret the measurements in the Minerve driven system. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

In Vivo Protein Dynamics on the Nanometer Length Scale and Nanosecond Time Scale

Selectively labeled GroEL protein was produced in living deuterated bacterial cells to enhance its neutron scattering signal above that of the intracellular milieu. Quasi-elastic neutron scattering shows that the in-cell diffusion coefficient of GroEL was (4.7 ± 0.3) × 10 –12 m 2 /s, a factor of 4 slower than its diffusion coefficient in buffer solution. Furthermore, for internal protein dynamics we see a relaxation time of (65 ± 6) ps, a factor of 2 slower compared to the protein in solution. Comparison to the literature suggests that the effective diffusivity of proteins depends on the length and time scale being probed. Retardation of in-cell diffusion compared to the buffer becomes more significant with the increasing probe length scale, suggesting that intracellular diffusion of biomolecules is nonuniform over the cellular volume. This approach outlined here enables investigation of protein dynamics within living cells to open up new lines of research using “in-cell neutron scattering” to study the dynamics of complex biomolecular systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cyclic-loading Induced Lattice-Strain Asymmetry in Loading and Transverse Directions

Cyclic-loading effects on a nickel-based superalloy are investigated with in-situ neutron-diffraction measurements. The thermoelastic-temperature evolution subjected to cyclic loading is estimated based on the lattice-strain evolution. The atomic thermoelastic responses are compared with the measured bulk temperature evolution. Two transitions in the temperature-evolution are observed. The first transition, observed with the neutron-measurement results, is associated with the cyclic hardening/softening-structural transformation. The second transition is observed at larger number of fatigue cycles. It has a distinct origin and is related to the start of irreversible structural transformations during fatigue. A lattice-strain asymmetry behavior is observed. The lattice-strain asymmetry is quantified as a grain-orientation-dependent transverse/loading parameter (P-ratio). The P-ratio parameter evolution reveals the irreversible plastic deformation subjected to the fatigue. The irreversible fatigue phenomena might relate to the formation of the microcracks. At elevated temperatures the cyclic hardening/softening transition starts at lower fatigue cycles as compared to room temperature. A comparison between the room-temperature and the elevated-temperature fatigue experiments is performed. The P-ratio parameters show the same irreversible trends at both the room and the elevated temperatures.

36 MATERIALS SCIENCE↗

A Brief Review of the Impact of Neutron Irradiation Damage in Tungsten and Its Alloys

Neutron irradiation poses a substantial challenge in the development and application of tungsten (W) and its alloys, predominantly in the framework of nuclear fusion and fission environments. Although W is well-acknowledged for its unique properties like its high melting temperature and higher resistance to sputtering, transmutation products, such as Re and Os, form and impact the alloy properties as a result of neutron irradiation. This transmutation effect accompanied by significant microstructure damage due to neutron irradiation can lead to the significant degradation of mechanical properties. This review surveys the literature focusing on the microstructural modifications post-irradiation and its impacts on the irradiation hardening. This review provides insights into the elaborative understanding on the neutron radiation damage on W and W alloys by exploring the microstructural evolution and hardness changes post-irradiation. The gaps and future opportunities for understanding neutron radiation damage in W are briefly summarized.

36 MATERIALS SCIENCE↗

A Combined Global and Local Approach to Elucidate Spatial Organization of the Mycobacterial ParB-parS Partition Assembly

Combining diverse sets of data at global (size, shape) and local (residue) scales is an emerging trend for elucidating the organization and function of the cellular assemblies. We used such a strategy, combining data from X-ray and neutron scattering with H/D-contrast variation and X-ray footprinting with mass spectrometry, to elucidate the spatial organization of the ParB-parS assembly from Mycobacterium tuberculosis. The ParB-parS participates in plasmid and chromosome segregation and condensation in predivisional bacterial cells. ParB polymerizes around the parS centromere(s) to form a higher-order assembly that serves to recruit cyto-skeletal ParA ATPases and SMC proteins for chromosome segregation. A hybrid model of the ParB-parS was built by combining and correlating computational models with experiment-derived information about size, shape, position of the symmetry axis within the shape, internal topology, DNA-protein interface, exposed surface patches, and prior knowledge. This first view of the ParB-parS leads us to propose how ParB spread on the chromosome to form a larger assembly.

59 BASIC BIOLOGICAL SCIENCES↗

Resolving Rapid Variation in Energy for Particle Transport

Resolving the rapid variation in energy in neutron and thermal radiation transport is needed for the predictive simulation capability in high-energy density physics applications. Energy variation is difficult to resolve due to rapid variations in cross sections and opacities caused by quantized energy levels in the nuclei and electron clouds. In recent work, we have developed a new technique to simultaneously capture slow and rapid variations in the opacities and the solution using homogenization theory, which is similar to multiband (MB) and to the finite-element with discontiguous support (FEDS) method, but does not require closure information. We demonstrated the accuracy and efficiency of the method for a variety of problems. We are researching how to extend the method to problems with multiple materials and the same material but with different temperatures and densities. In this highlight, we briefly describe homogenization theory and some results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Sensitivity and Limitations of Structures from X-ray and Neutron-Based Diffraction Analyses of Transition Metal Oxide Lithium-Battery Electrodes

Lithium transition metal oxides are an important class of electrode materials for lithium-ion batteries. Binary or ternary (transition) metal doping brings about new opportunities to improve the electrode’s performance and often leads to more complex stoichiometries and atomic structures than the archetypal LiCoO 2 . Rietveld structural analyses of X-ray and neutron diffraction data is a widely-used approach for structural characterization of crystalline materials. But, different structural models and refinement approaches can lead to differing results, and some parameters can be difficult to quantify due to the inherent limitations of the data. Here, through the example of LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA), we demonstrated the sensitivity of various structural parameters in Rietveld structural analysis to different refinement approaches and structural models, and proposed an approach to reduce refinement uncertainties due to the inexact X-ray scattering factors of the constituent atoms within the lattice. Furthermore, this refinement approach was implemented for electrochemically-cycled NCA samples and yielded accurate structural parameters using only X-ray diffraction data. The present work provides the best practices for performing structural refinement of lithium transition metal oxides.

25 ENERGY STORAGE↗

Further Evaluation of the Neutron Resonance Transmission Analysis (NRTA) Technique for Assaying Plutonium in Spent Fuel

This is an end-of-year report (Fiscal Year (FY) 2011) for the second year of effort on a project funded by the National Nuclear Security Administration's Office of Nuclear Safeguards (NA-241). The goal of this project is to investigate the feasibility of using Neutron Resonance Transmission Analysis (NRTA) to assay plutonium in commercial light-water-reactor spent fuel. This project is part of a larger research effort within the Next-Generation Safeguards Initiative (NGSI) to evaluate methods for assaying plutonium in spent fuel, the Plutonium Assay Challenge. The second-year goals for this project included: (1) assessing the neutron source strength needed for the NRTA technique, (2) estimating count times, (3) assessing the effect of temperature on the transmitted signal, (4) estimating plutonium content in a spent fuel assembly, (5) providing a preliminary assessment of the neutron detectors, and (6) documenting this work in an end of the year report (this report). Research teams at Los Alamos National Laboratory (LANL), Lawrence Berkeley National Laboratory (LBNL), Pacific Northwest National Laboratory (PNNL), and at several universities are also working to investigate plutonium assay methods for spent-fuel safeguards. While the NRTA technique is well proven in the scientific literature for assaying individual spent fuel pins, it is a newcomer to the current NGSI efforts studying Pu assay method techniques having just started in March 2010; several analytical techniques have been under investigation within this program for two to three years or more. This report summarizes work performed over a nine month period from January-September 2011 and is to be considered a follow-on or add-on report to our previous published summary report from December 2010 (INL/EXT-10-20620).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Cobalt-based pyroxenes: A new playground for Kitaev physics

Recent advances in the study of cobaltites have unveiled their potential as a promising platform for realizing Kitaev physics in honeycomb systems and the Ising model in weakly coupled chain materials. In this manuscript, we explore the magnetic properties of pyroxene SrCoGe 2 O 6 using a combination of neutron scattering, ab initio methods, and linear spin-wave theory. Through careful examination of inelastic neutron scattering powder spectra, we propose a modified Kitaev model to accurately describe the twisted chains of edge-sharing octahedra surrounding Co 2+ ions. The extended Kitaev–Heisenberg model, including a significant anisotropic bond-dependent exchange term with K/|J| = 0.96, is identified as the key descriptor of the magnetic interactions in SrCoGe 2 O 6 . Furthermore, our heat capacity measurements reveal an effect of an external magnetic field (approximately 13 T) which shifts the system from a fragile antiferromagnetic ordering with T N = 9 K to a field-induced state. We argue that pyroxenes, particularly those modified by substituting Ge with Si and its less extended p orbitals, emerge as a platform for the Kitaev model. This opens up possibilities for advancing our understanding of Kitaev physics.

36 MATERIALS SCIENCE↗

Neutron Imaging of Al6061 Prepared by Solid-State Friction Stir Additive Manufacturing

Solid-state Friction Stir Additive Manufacturing has recently gained attention as a result of its capacity to fabricate large-scale parts while preserving the mechanical properties of the feedstock material. However, the correlation between the quality of layer-by-layer bonding of the deposited metal and processing parameters has remained unknown. Neutron imaging techniques, with 90% total transmission per cm, are employed for Al6061 parts fabricated by MELD ® Technology as a non-destructive evaluation approach for the first time to investigate the layer-by-layer structure of a stadium-shaped ingot in different sections. The post-processed results show the fabricated parts with an optimized set of processing parameters are void-free. However, the hydrocarbon-based feedstock lubricant segregates between the layers, which consequently may lead to non-uniform weaker mechanical properties along the build direction and stimulate crack initiation during mechanical loading. The tensile test results show 14% lower strain-to-failure values in alleged contaminated areas in transmission imaging results. Additionally, layer bonding is significantly impacted by hot-on-hot and hot-on-cold layer deposition schemes, especially for larger layer thicknesses.

36 MATERIALS SCIENCE↗

Empirical Investigation of Properties for Additive Manufactured Aluminum Metal Matrix Composites

Laser additive manufacturing with mixed powders of aluminum alloy and silicon carbide (SiC) or boron carbide (B4C) is investigated in this experiment. With various mixing ratios of SiC/Al to form metal matrix composites (MMC), their mechanical and physical properties are empirically investigated. Parameters such as laser power, scan speed, scan pattern, and hatching space are optimized to obtain the highest density for each mixing ratio of SiC/Al. The mechanical and thermal properties are systematically investigated and compared with and without heat treatment. It shows that 2 wt% of SiC obtained the highest strength and Young’s modulus. Graded composite additive manufacturing (AM) of MMC is also fabricated and characterized. Various types of MMC devices, such as heat sink using graded SiC MMC and grid type three-dimensional (3D) neutron collimators using boron carbide (B4C), were also fabricated to demonstrate their feasibility for applications.

36 MATERIALS SCIENCE↗

Phase stability, swelling, microstructure and strength of Ti 3 SiC 2 -TiC ceramics after low dose neutron irradiation

In this study, M n+1 AX n (MAX) phase Ti 3 SiC 2 materials were neutron irradiated at ~400, ~630, and 700 °C to a fluence of ~2 × 10 25 n/m 2 (E > 0.1 MeV). After irradiation at ~400 °C, anisotropic c-axis dilation of ~1.5% was observed. Room temperature strength was reduced from 445 ± 29 MPa to 315 ± 33 MPa and the fracture surfaces showed flat facets and transgranular cracks instead of typical kink-band deformation and bridging ligaments. XRD phase analysis indicated an increase of 10–15 wt% TiC. After irradiation at ~700 °C there were no lattice parameter changes, ~5 wt% decomposition to TiC occurred, and strength was 391 ± 71 MPa and 378 ± 31 MPa. The fracture surfaces indicated kink-band based deformation but with lesser extent of delamination than as-received samples. Finally, Ti 3 SiC 2 appears to be radiation tolerant at ~400 °C, and increasingly radiation resistant at ~630–700 °C, but a higher temperature may be necessary for full recovery.

36 MATERIALS SCIENCE↗

Structural properties of plastically deformed SrTiO 3 and KTaO 3

Dislocation engineering has the potential to open new avenues toward the exploration and modification of the properties of quantum materials. Strontium titanate (SrTi⁢O 3 , STO) and potassium tantalate (KTa⁢O 3 , KTO) are incipient ferroelectrics that show metallization and superconductivity at extremely low charge-carrier concentrations and have been the subject of resurgent interest. These materials also exhibit remarkable ambient-temperature ductility, and thus represent exceptional platforms for studies of the effects of deformation-induced dislocation structures on electronic properties. Recent work on plastically deformed STO revealed an enhancement of the superconducting transition temperature and the emergence of local ferroelectricity and magnetism near self-organized dislocation walls. Here, in this work, we present a comprehensive structural analysis of plastically deformed STO and KTO, employing specially designed strain cells, diffuse neutron and x-ray scattering, Raman scattering, and nuclear magnetic resonance (NMR). Diffuse scattering and NMR provide insight into the dislocation configurations and densities and their dependence on strain. As in the prior work on STO, Raman scattering reveals evidence for local ferroelectric order near dislocation walls in plastically deformed KTO. Our findings provide valuable information about the self-organized defect structures in both materials, and they position KTO as a second model system in which to explore the associated emergent physics.

36 MATERIALS SCIENCE↗

Determination of spallation neutron flux through spectral adjustment techniques

The Los Alamos Isotope Production Facility (IPF) creates medical isotopes using a proton beam impinged on a target stack. Spallation neutrons are created in the interaction of the beam with target. The use of these spallation neutrons to produce additional radionuclides has been proposed in this paper. However, the energy distribution and magnitude of the flux is not well understood. Finally, a modified SAND-II spectral adjustment routine has been used with radioactivation foils to determine the differential neutron fluence for these spallation neutrons during a standard IPF production run.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Additive Manufacturing of Research Reactor Control Elements and Subsequent Neutron Irradiation

Additive manufacturing techniques have made major strides in recent years and are now capable of creating complex components in near-final form. The nuclear industry has many applications with complicated and even unique components that are time consuming, expensive, and more difficult to make using traditional fabrication routes. Modern fabrication techniques possess the potential to reduce fabrication lead-time and costs while increasing quality and efficiency. However, these methods have not been adopted due to the need for strict validation for nuclear applications. Unlike structural components that largely consist of a uniform material, for nuclear reactor core components incorporation of fissile or neutron poison materials inside a cladding becomes necessary. This in turn requires a more complex and flexible manufacturing method to produce these hybrid components. In this study, demonstration of ultrasonic additive manufacturing (UAM) process to produce components resembling research reactor control elements was carried out]. Specifically, the control elements for ORNL's High Flux Isotope Reactor (HFIR) were targeted. These control elements (consisting of an inner cylinder and four outer plates) are placed on the periphery of the circular HFIR core. The control elements consist of Al6061-T6 alloy with a 13-cm-long grey and a 56-cm-long black region, corresponding to 40 wt% of Ta and 30 wt% Eu{sub 2}O{sub 3} (europia) are incorporated along their length. In this study various fabrication parameters for production of aluminum blocks with and without embedded Eu{sub 2}O{sub 3} and Ta bearing compacts were explored. Select optimized specimens we then irradiated inside HFIR for one reactor cycle. The UAM process exploits ultrasonic energy to facilitate solid-state welding of metal foils in contact under pressure. This additive process is carried out in successive layers to build up the material and when coupled with CNC milling, it yields complex 3D components. The milling and subsequent additive steps may be used to embed foreign material into the material undergoing buildup. In this manner fissile or neutron poison elements may be incorporated into the complex structure, though in an inhomogeneous fashion. Multiple Al-6061 blocks were produced by UAM using 25 mm wide by 0.15 mm thick Al-6061-H18 tapes. The mechanical properties of these blocks in the as-fabricated condition was characterized in detail and it was shown that a great degree of anisotropy in the mechanical behavior exists between the direction in the tape plane and the direction perpendicular to the tapes (buildup direction) The latter exhibited reduced modulus and significantly smaller strength. Post production heat treatment appeared to greatly enhance the strength in the buildup direction. Multiple tensile specimens machined per SS-J3 geometry were prepared for irradiation testing. The tensile specimen matrix was set up to enable post irradiation examination of mechanical properties in various directions as well as after heat treatment. A small block with embedded Ta- and Eu{sub 2}O{sub 3}-bearing compacts, three of each kind, was also produced, as demonstrated previously. These compacts were 5.7 mm in diameter and 1.6 mm in height and contained 60 vol Ta or Eu{sub 2}O{sub 3}. The poison-bearing Al-6061 block alongside the tensile bars was loaded into a perforated rabbit (irradiation capsule) for irradiation in HFTK. The perforated rabbit allows penetration of HFIR water coolant into the Interior of the capsule in direct contact with the test specimens. The rabbit was loaded into the flux trap region at the uppermost position in the core. Irradiation temperature was 68 deg. C and fast neutron (E>0.1 MeV) fluence was 10{sup 25} neutrons/m{sup 2}. Currently PIE activities are ongoing that are focused on mechanical testing of irradiated tensile bars and metallographic examination of neutron poison bearing block.

36 MATERIALS SCIENCE↗

Effect of Applied Stress and Temperature on Residual Stresses Induced by Peening Surface Treatments in Alloy 600

In this study, the effects of applied tensile stress and temperature on laser shock peening (LSP) and cavitation shotless peening (CSP)-induced compressive residual stresses were investigated using neutron and x-ray diffraction. Residual stresses on the surface, measured in situ, were lower than the applied stress in LSP- and CSP-treated Alloy 600 samples (2 mm thick). The residual stress averaged over the volume was similar to the applied stress. Compressive residual stresses on the surface and balancing tensile stresses in the interior relax differently due to hardening induced by LSP. Ex situ residual stress measurements, using XRD, show that residual stresses relaxed as the applied stress exceeded the yield strength of the LSP- and CSP-treated Alloy 600. Compressive residual stresses induced by CSP and LSP decreased by 15-25% in magnitude, respectively, on exposure to 250-450 °C for more than 500 h with 10-11% of relaxation occurring in the first few hours. Further, 80% of the compressive residual stresses induced by LSP and CSP treatments in Alloy 600 were retained even after long-term aging at 350 °C for 2400 h.

36 MATERIALS SCIENCE↗

Second Target Station Bunker Shielding with Populated and Unpopulated Neutron Beamlines: Preliminary Design

At the U.S. Department of Energy’s Oak Ridge National Laboratory, the Second Target Station (STS) beamline sources for preliminary design have been used to perform a shielding analysis of the bunker. Prompt total effective dose rates (i.e., neutron plus photon effective dose rates when the proton beam is on) were calculated on top of the bunker roof and outside the bunker wall. These areas outside the bunker will be generally accessible, so the prompt total dose rate in these areas should not exceed 2.5 μSv . h -1 (0.25 mrem . h -1 ). This paper presents the required shielding thicknesses to meet this dose rate limit. In one instance, this dose rate limit is not met: For a combination of populated and unpopulated beamlines, the prompt total dose rate outside the bunker across from the unpopulated beamline, which has less shielding because of the lack of beamline shielding, slightly exceeds 2.5 μSv . h -1 . In conclusion, once more details are known regarding the STS high-density concrete density and composition, a future analysis will investigate the shielding modifications required to reduce the calculated prompt total dose rates for this configuration to less than 2.5 μSv . h -1 .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗