Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Frequency control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Novel Active Combustion Control Valve

This project presents an innovative solution for active combustion control. Relative to the state of the art, this concept provides frequency modulation (greater than 1,000 Hz) in combination with high-amplitude modulation (in excess of 30 percent flow) and can be adapted to a large range of fuel injector sizes. Existing valves often have low flow modulation strength. To achieve higher flow modulation requires excessively large valves or too much electrical power to be practical. This active combustion control valve (ACCV) has high-frequency and -amplitude modulation, consumes low electrical power, is closely coupled with the fuel injector for modulation strength, and is practical in size and weight. By mitigating combustion instabilities at higher frequencies than have been previously achieved (approximately 1,000 Hz), this new technology enables gas turbines to run at operating points that produce lower emissions and higher performance.

Caspermeyer, Matt↗
NASA NTRS1987

Frequency-shaped large-angle maneuvers

The paper considers the problem of maneuvering a flexible spacecraft through large angles in finite time. The basic control problem is divided into two parts. The first part consists of generating a frequency-shaped open-loop solution for the nonlinear rigid body as the nominal solution. The resulting two-point boundary-value problem is solved by introducing a continuation method for altering the mass distribution and boundary conditions for the spacecraft. For the second part, a feedback control is designed by linearizing the flexible body response about several points along the rigid body nominal solution. The perturbation gains are designed by using a frequency-shaped cost functional approach. The gains are linearly interpolated to produce smooth control time-histories as the linear piecewise constant plant models change during the maneuver.

Chun, Hon M.↗
NASA NTRS2005

Epstein-Barr virus shedding by astronauts during space flight

Patterns of Epstein-Barr virus (EBV) reactivation in 32 astronauts and 18 healthy age-matched control subjects were characterized by quantifying EBV shedding. Saliva samples were collected from astronauts before, during, and after 10 space shuttle missions of 5-14 days duration. At one time point or another, EBV was detected in saliva from each of the astronauts. Of 1398 saliva specimens from 32 astronauts, polymerase chain reaction analysis showed that 314 (23%) were positive for EBV DNA. Examination by flight phase showed that 29% of the saliva specimens collected from 28 astronauts before flight were positive for EBV DNA, as were 16% of those collected from 25 astronauts during flight and 16% of those collected after flight from 23 astronauts. The mean number of EBV copies from samples taken during the flights was 417 per mL, significantly greater (p<.05) than the number of viral copies from the preflight (40) and postflight (44) phases. In contrast, the control subjects shed EBV DNA with a frequency of 3.7% and mean number of EBV copies of 40 per mL of saliva. Ten days before flight and on landing day, titers of antibody to EBV viral capsid antigen were significantly (p<.05) greater than baseline levels. On landing day, urinary levels of cortisol and catecholamines were greater than their preflight values. In a limited study (n=5), plasma levels of substance P and other neuropeptides were also greater on landing day. Increases in the number of viral copies and in the amount of EBV-specific antibody were consistent with EBV reactivation before, during, and after space flight.

Randomized Controlled Trial↗
NASA NTRS1973

Suppression of flutter

An active aerodynamic control system to control flutter over a large range of oscillatory frequencies is described. The system is not affected by mass, stiffness, elastic axis, or center of gravity location of the system, mode of vibration, or Mach number. The system consists of one or more pairs of leading edge and trailing edge hinged or deformable control surfaces, each pair operated in concert by a stability augmentation system. Torsion and bending motions are sensed and converted by the stability augmentation system into leading and trailing edge control surface deflections which produce lift forces and pitching moments to suppress flutter.

Nissim, E.↗
NASA NTRS1989

A simple active controller to suppress helicopter air resonance in hover and forward flight

A coupled rotor/fuselage helicopter analysis with the important effects of blade torsional flexibility, unsteady aerodynamics, and forward flight is presented. This model is used to illustrate the effect of unsteady aerodynamics, forward flight, and torsional flexibility on air resonance. Next, a nominal configuration, which experiences air resonance in forward flight, is selected. A simple multivariable compensator using conventional swashplate inputs and a single body roll rate measurement is then designed. The controller design is based on a linear estimator in conjunction with optimal feedback gains, and the design is done in the frequency domain using the loop-transfer recovery method. The controller is shown to suppress the air resonance instability throughout wide range helicopter loading conditions and forward flight speeds.

Friedmann, P. P.↗
NASA NTRS1998

Jet Injection Used to Control Rotating Stall in a High-Speed Compressor

In a joint effort between the Massachusetts Institute of Technology (MIT) and the NASA Lewis Research Center, a new technology was demonstrated to identify and control rotating stall and surge in a single-stage, high-speed compressor. Through the use of highvelocity, high-frequency jet injectors, the instabilities of surge and stall were controlled in a high-speed compressor rig. Through the use of active stall control, modal instabilities that normally occur in the pressure measurements prior to stall were normalized and the range of the compressor was extended. Normally the events of rotating stall and surge instabilities limit the operation of the aeroengine compressor to a region below the surge line. To enhance the performance of the compressor, the Lewis/MIT team used active stall control methods to extend the normal operation of the compressor beyond the original stall point.

Bright, Michelle M.↗
DOE OSTI2023

Effect of Wind Gusts on Local Run-of-River Hydro Plants

In this work, we focus on the integration of wind farms in a hydro dominated power system, and analyze the challenges and solutions associated with this integration. Due to sudden increase in wind power, the system frequency can increase, causing excessive reduction in the run-of-river (ROR) system’s power. This can result in damage to the physical structure due to water level violations and cause issues for downstream customers. To prevent excessive and prolonged ROR power deviations, and to prevent tie-line deviations, we are proposing a wind-hydro centralized coordination scheme, which is not existing currently. The controller showed promising results by reducing the system frequency extrema by 0.8Hz.

13 HYDRO ENERGY↗
NASA NTRS2013

Millimeter-Wave Localizers for Aircraft-to-Aircraft Approach Navigation

Aerial refueling technology for both manned and unmanned aircraft is critical for operations where extended aircraft flight time is required. Existing refueling assets are typically manned aircraft, which couple to a second aircraft through the use of a refueling boom. Alignment and mating of the two aircraft continues to rely on human control with use of high-resolution cameras. With the recent advances in unmanned aircraft, it would be highly advantageous to remove/reduce human control from the refueling process, simplifying the amount of remote mission management and enabling new operational scenarios. Existing aerial refueling uses a camera, making it non-autonomous and prone to human error. Existing commercial localizer technology has proven robust and reliable, but not suited for aircraft-to-aircraft approaches like in aerial refueling scenarios since the resolution is too coarse (approximately one meter). A localizer approach system for aircraft-to-aircraft docking can be constructed using the same modulation with a millimeterwave carrier to provide high resolution. One technology used to remotely align commercial aircraft on approach to a runway are ILS (instrument landing systems). ILS have been in service within the U.S. for almost 50 years. In a commercial ILS, two partially overlapping beams of UHF (109 to 126 MHz) are broadcast from an antenna array so that their overlapping region defines the centerline of the runway. This is called a localizer system and is responsible for horizontal alignment of the approach. One beam is modulated with a 150-Hz tone, while the other with a 90-Hz tone. Through comparison of the modulation depths of both tones, an autopilot system aligns the approaching aircraft with the runway centerline. A similar system called a glide-slope (GS) exists in the 320-to-330MHz band for vertical alignment of the approach. While this technology has been proven reliable for millions of commercial flights annually, its UHF nature limits its ability to operate beyond the 1-to-2-meter precisions associated with commercial runway width. A prototype ILS-type system operates at millimeter-wave frequencies to provide automatic and robust approach control for aerial refueling. The system allows for the coupling process to remain completely autonomous, as a boom operator is no longer required. Operating beyond 100 GHz provides enough resolution and a narrow enough beamwidth that an approach corridor of centimeter scales can be maintained. Two modules were used to accomplish this task. The first module is a localizer/glide-slope module that can be fitted on a refueling aircraft. This module provides the navigation beams for aligning the approaching aircraft. The second module is navigational receiver fitted onto the approaching aircraft to be re fueled that can detect the approach beams. Since unmanned aircraft have a limited payload size and limited electrical power, the receiver portion was implemented in CMOS (complementary metal oxide semiconductor) technology based on a super-regenerative receiver (SRR) architecture. The SRR achieves mW-level power consumption and chip sizes less than l mm2. While super-regenerative techniques have small bandwidths that limit use in communication systems, their advantages of high sensitivity, low complexity, and low power make them ideal in this situation where modulating tones of less than 1 kHz are used.

Tang, Adrian J.↗
NASA NTRS1995

An investigation of the effects of pitch-roll (de)-coupling on helicopter handling qualities

An investigation of the effects of pitch-roll coupling on helicopter handling qualities was performed by the US Army and DLR, using a NASA ground-based and a DLR inflight simulator. Over 90 different coupling configurations were evaluated using a roll-axis tracking task. The results show that although the current ADS-33C coupling criterion discriminates against those types of coupling typical of conventionally controlled helicopters, it not always suited for the prediction of handling qualities of helicopters with modern control systems. Based on the observation that high frequency inputs during tracking are used to alleviate coupling, a frequency domain pitch-roll coupling criterion that uses the average coupling ratio between the bandwidth and neutral stability frequency is formulated. This criterion provides a more comprehensive coverage with respect to the different types of coupling and shows excellent consistency.

CONTROL COUPLING↗
NASA NTRS1972

Off-line data analysis and data reduction from digitally controlled random test systems.

This paper discusses the merits of employing the new computer-controlled random environment control systems for fast and efficient large-scale data analysis when they are not being used for test control. Hardware and software requirements are stated. Several of the more familiar frequency functions are defined from the Fourier coefficients, the main product of the Fourier processors used in these control systems. Another function, the probability density function, is defined and suggestions for its application are made. An analysis example is presented. Some programming tips are listed, and the accuracy and reliability of frequency analysis measurements are considered.

Chapman, C. P.↗
NASA NTRS1985

Robust Control Design for Large Space Structures

The control design problem for the class of future spacecraft referred to as large space structures (LSS) is by now well known. The issue is the reduced order control of a very high order, lightly damped system with uncertain system parameters, particularly in the high frequency modes. A design methodology which incorporates robustness considerations as part of the design process is presented. Combining pertinent results from multivariable systems theory and optimal control and estimation, LQG eigenstructure assignment and LQG frequency shaping, were used to improve singular value robustness measures in the presence of control and observation spillover.

Eastman, W. L.↗
NASA NTRS2013

Microwave Kinetic Inductance Detector with Selective Polarization Coupling

A conventional low-noise detector requires a technique to both absorb incident power and convert it to an electrical signal at cryogenic temperatures. This innovation combines low-noise detector and readout functionality into one device while maintaining high absorption, controlled polarization sensitivity, and broadband detection capability. The resulting far-infrared detectors can be read out with a simple approach, which is compact and minimizes thermal loading. The proposed microwave kinetic inductance detector (MKID) consists of three basic elements. The first is the absorptive section in which the incident power is coupled to a superconducting resonator at far-infrared frequency above its superconducting critical frequency (where superconductor becomes normal conductor). This absorber's shape effectively absorbs signals in the desired polarization state and is resonant at the radio frequency (RF) used for readout of the device. Control over the metal film used in the absorber allows realization of structures with either a 50% broadband or 100% resonance absorptance over a 30% fractional bandwidth. The second element is a microwave resonator - which is realized from the thin metal films used to make the absorber as transmission lines - whose resonance frequency changes due to a variation in its kinetic inductance. The resonator's kinetic inductance is a function of the power absorbed by the device. A low-loss dielectric (mono-crystalline silicon) is used in a parallel-plate transmission line structure to realize the desired superconducting resonators. There is negligible coupling among the adjacent elements used to define the polarization sensitivity of each detector. The final component of the device is a microwave transmission line, which is coupled to the resonator, and allows detection of changes in resonance frequency for each detector in the focal plane array. The spiral shape of the detector's absorber allows incident power with two polarizations to couple to the detector equally. A stepped impedance resonator was used that allows the incident power absorbed in the detecting membrane area to be uniformly distributed in the detector's transmission line at the RF readout frequency. This maximizes the sensitivity of the detector. The signal is read out via a frequency multiplexing technique that requires a minimum number of interface transmission lines for readout. This reduces the packaging complexity and coupling to the device's thermal environment.

Wollack, Edward↗
NASA NTRS2018

Electric Motor Noise from Small Quadcopters: Part II - Source Characteristics

The increased interest in electric motors for aircraft propulsion systems has driven interest in quantifying the contribution of electric motor noise to the overall sound levels and possibly human annoyance of the propulsion system. This work presents acoustic measurements of electric motors used for small quadcopters to quantify the sound produced by a number of outrunner motors with different types of controllers. Results are presented for loaded and unloaded motors as well as installed and uninstalled configurations. Motor resonance frequencies were measured and computed. Current probe measurements showed significant harmonic content in the supply current from the controllers for both the conventional and sinewave controllers. Acoustic results showed motor noise is typically radiated at frequencies near that for azimuthal vibration mode number 2 of the rotor which occurs at roughly 5000 Hz. Electric motor noise was evident in the spectra produced by many of the motor-controller combinations for motors loaded with propellers with levels often greater than those for the motor alone due to increases in the stator magnetic flux density with increased current. An installed quadcopter configuration produced increases in acoustic radiation over that of the uninstalled motor in a frequency range near the 1200 Hz azimuthal vibration mode 1 of the rotor.

Henderson, Brenda↗
NASA NTRS1983

Attitude control and stability of a Space Station

Certain problems arise in connection with the design and construction of a Space Station. These problems are partly related to the impossibility to predict in advance the ultimate form and size which the Space Station will assume. Due to the abatement of volume and strength constraints it will be desirable (for maximum utility of mass) to permit very low structural resonance frequencies, and due to complexity of the configuration there will be an extremely high density of modal frequencies. The basic approaches available to an attitude control system designer for coping with the dynamics of a plant with the considered characteristics are examined. In order to overcome difficulties related to a use of currently widely considered approaches, a technique is proposed whereby the degrees of freedom requiring active control are isolated mechanically from other superfluous vibratory modes.

Peters, W. H.↗
DOE OSTI2020

Control-Oriented Modeling of Lithium-Ion Batteries

Battery management systems (BMSs), which monitor and optimize performance while ensuring safety, require control-oriented models, i.e., models tailored to the design and implementation of estimation and control algorithms. Physics-based electrochemical models describe detailed battery phenomena, but are too computationally intensive for use in estimation and control applications. Single particle models (SPMs), which retain some of the physics of electrochemical models, are often used for control-oriented battery modeling since they are computationally efficient; however, they are only valid over very low frequency ranges and C-rates. Empirical equivalent circuit models (ECMs) are also used for control-oriented battery modeling since they are computationally efficient and can describe battery behavior over wide frequency ranges; however, they provide no physical understanding of the battery and, therefore, have limited applicability. Further, fractional order terms (e.g., Warburg impedances) are often employed, making the models unwieldy for use in the time domain. This work provides a control-oriented battery model that combines the benefits of SPM and ECM models, while overcoming their limitations. The proposed model incorporates some of the battery physics found in electrochemical models, can easily be used in both the time and frequency domains, and describes battery behavior over its entire frequency range. A linearized single particle model, which incorporates key electrochemical parameters, is used for modeling battery physics at very low frequencies. For low frequencies, integer-order linear systems are used to approximate diffusion physics described by Warburg impedances, and high frequency behavior is modeled by the double layer capacitance effect. The proposed battery model is more computationally efficient than full electrochemical models since it does not require the solution of PDEs, is accurate for a wider frequency range than the SPM considered in this paper, and does not suffer from the unwieldiness and limited applicability of empirical ECMs. Finally, the model is validated in the time and frequency domains via a comparison to pseudo-two-dimensional (P2D) model simulations and experimental data.

25 ENERGY STORAGE↗