Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Forming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Technetium Waste Form Development - Progress Report

Analytical electron microscopy using SEM and TEM has been used to analyze a ~5 g. ingot with composition 71.3 wt% 316SS-5.3 wt% Zr-13.2 wt% Mo-4.0 wt% Rh-6.2 wt% Re prepared at the Idaho National Laboratory. Four phase fields have been identified two of which are lamellar eutectics, with a fifth possibly present. A Zr rich phase was found distributed as fine precipitate, ~10µm in diameter, often coating large cavities. A Mo-Fe-Re-Cr lamellar eutectic phase field appears as blocky regions ~30µm in diameter, surrounded by a Fe-Mo-Cr lamellar eutectic phase field, and that in turn is surrounded by a Zr-Fe-Rh-Mo-Ni phase field. The eutectic phase separation reactions are different. The Mo-Fe-Re-Cr lamellar eutectic appears a result of austenitic steel forming at lower volume fraction within an Mo-Fe-Re intermetallic phase, whereas the Fe-Mo-Cr lamellar eutectic may be a result of the same intermetallic phase forming within a ferritic steel phase. Cavitation may have arisen either as a result of bubbles, or from loss of equiaxed particles during specimen preparation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

High Precision Measurement of the Proton Elastic Form Factor Ratio at Low Q 2

Experiment E08-007 measured the proton elastic form factor ratio μ p G E /G M in the range of Q 2 = 0.3-0.7(GeV/c) 2 by recoil polarimetry. Data were taken in 2008 at the Thomas Jefferson National Accelerator Facility in Virginia, USA. A 1.2 GeV polarized electron beam was scattered off a cryogenic hydrogen target. The recoil proton was detected in the left HRS in coincidence with the elasticly scattered electrons tagged by the BigBite spectrometer. The proton polarization was measured by the focal plane polarimeter (FPP). In this low Q 2 region, previous measurement from Jefferson Lab Hall A (LEDEX) along with various fits and calculations indicate substantial deviations of the ratio from unity. For this new measurement, the proposed statistical uncertainty (< 1%) was achieved. These new results are a few percent lower than expected from previous world data and fits, which indicate a smaller G Ep at this region. Beyond the intrinsic interest in nucleon structure, the new results also have implications in determining the proton Zemach radius and the strangeness form factors from parity violation experiments.

08 HYDROGEN↗

A Generic Primary-Control Model for Grid-Forming Inverters: Towards Interoperable Operation & Control

This paper outlines an architectural vision centered around the notion of interoperability to integrate grid-forming inverter-based resources in large-scale grids. With the underlying principle of interoperability guiding developments, we focus on modeling the characteristics of droop, virtual synchronous machine, and virtual oscillator controls. Emphasis is placed on these three controllers since they are leading grid-forming control candidates and are likely to be commonplace as primary-control schemes in future systems. We show that these controllers can each be considered as instantiations of a more generic model and that all these controllers exhibit similar droop-like relations between pertinent terminal variables in steady state. This commonality between controllers gives interoperability among them such that automatic synchronization, power sharing, and voltage regulation can be achieved. Simulation results validate the models and demonstrate how the steady-state droop characteristics of these control methods can be aligned with the aid of the developed modeling paradigm.

control↗

Cast Alumina-Forming Austenitic Stainless Steels for High Temperature Heat Treatment Furnace Rolls

Alloy developers worldwide have struggled to create creep-resistant alumina-forming, iron-based austenitic stainless steels for use as high-temperature structural alloys, but with limited success in balancing alloy cost, oxidation, and creep resistance. Here, this article describes the research and development of a novel cast alumina-forming austenitic stainless steel. This work won the prestigious Engineering Materials Achievement Award presented at IMAT 2023 in Detroit.

36 MATERIALS SCIENCE↗

Demonstrating the Need for Adaptive Droop Control for Grid-Forming Inverters in Islanded and Grid-Connected Modes

This paper demonstrates the need of adaptive droop of grid-forming (GFM) inverters operating in different operation modes (grid-connected and islanded). A pure hardware microgrid comprising multiple grid-forming (GFM) inverters from different vendors, multiple grid-following inverters, and a diesel generator is used for the demonstration. The key findings are summarized as follows: Tighter droop slope should be used in the islanded mode, and looser droop slope should be used in the grid-connected mode to ensure stability. It is important to have adaptive droop control in GFM inverters to ensure stable and reliable microgrid operation.

14 SOLAR ENERGY↗

Sculpturing, forming, and spinning of large components for launch vehicles

At .the beginning of the S-IC booster contract, it was evident that certain manufacturing techniques would have to be developed before the proposed design could be put into full production. Much of the development activity that has been accomplished was initiated because the size of booster components was greater than the capacities of available equipment. This paper describes some of the more significant methods that have evolved from this development activity, and which demonstrate how the capability to manufacture S-IC components such as bulkhead gore segments, tank skins, Y-rings, and lox tunnels, has been acquired. The fabrication methods used to transform 2219 aluminum alloy plate into the large, sculptured, and contoured parts that make up the structural surfaces of the booster include hydraulic bulge forming, age forming, and adaptations of conventional skin milling and chemical milling processes. The importance of fixturing and the machining sequence related to fabrication of the Y-ring are pointed out. The shear-spinning process that is used to produce a seamless, one-piece lox tunnel 40 feet long from a cylindrical blank only 62 inches long is described. The presentation is concluded with a synopsis of the current design changes that are being implemented to improve strength-to-weight ratios. A brief statement of possible future activity is included.

Milling↗

Measurement of |Vcb| and the Form-Factor Slope in Bbar -> Dlnu Decays in Events Tagged by a Fully Reconstructed B Meson

We present a measurement of the Cabibbo-Kobayashi-Maskawa matrix element |V{sub cb}| and the form-factor slope {rho}{sup 2} in {bar B} {yields} D{ell}{sup -} {bar {nu}}{sub {ell}} decays based on 460 million B{bar B} events recorded at the {Gamma}(4S) resonance with the BABAR detector. {bar B} {yields} D{ell}{sup -} {bar {nu}}{sub {ell}} decays are selected in events in which a hadronic decay of the second B meson is fully reconstructed. We measure the differential decay rate and determine G(1)|V{sub cb}| = (43.0 {+-} 1.9 {+-} 1.4) x 10{sup -3} and {rho}{sup 2} = 1.20 {+-}0.09 {+-} 0.04, where G(1) is the hadronic form factor at the point of zero recoil. We also determine the exclusive branching fractions and find {Beta}(B{sup -} {yields} D{sup 0} {ell}{sup -}{bar {nu}}{sub {ell}}) = (2.31 {+-} 0.08 {+-} 0.09)% and {Beta}(B{sup 0} {yields} D{sup +} {ell}{sup -} {bar {nu}}{sub {ell}}) = (2.23 {+-} 0.11 {+-} 0.11)%.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nucleon form factors from high statistics mixed-action calculations with 2+1 flavors

We present new high-statistics results for nucleon form factors at pion masses of approximately 290, 350, 500, and 600 MeV using a mixed action of domain wall valence quarks on an improved staggered sea. We perform chiral fits to both vector and axial form factors and compare our results to experiment.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Semileptonic Form Factor ratio B_s->D_s/B->D and Its Application to BR(B^0_s->\mu^+\mu^-)

We present a (2+1)-flavor lattice QCD calculation of the form factor ratio between the semileptonic decays {bar B}{sub s}{sup 0} {yields} D{sub s}{sup +}l{sup -}{bar {nu}} and {bar B}{sup 0} {yields} D{sup +}l{sup -}{bar {nu}}. This ratio is an important theoretical input to the hadronic determination of the B meson fragmentation fraction ratio f{sub s}/f{sub d} which enters in the measurement of BR(B{sub s}{sup 0} {yields} {mu}{sup +}{mu}{sup -}). Small lattice spacings and high statistics enable us to simulate the decays with a dynamic final D meson of small momentum and reliably extract the hadronic matrix elements at nonzero recoil. We report our preliminary result for the form factor ratio at the corresponding momentum transfer of the two decays f{sub 0}{sup (s)} (M{sub {pi}}{sup 2})/f{sub 0}{sup (d)} (M{sub K}{sup 2}).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

ISR Hadron Production in e+e- Annihilations and Meson-Photon Transition Form Factors

We present several recent results from the BaBar collaboration in the areas of initial state radiation physics and transition form factors. An updated study of the processes e{sup +}e{sup -} {yields} K{sup +}K{sup -}{pi}{sup +}{pi}{sup -} and e{sup +}e{sup -} {yields} K{sup +}K{sup -}{pi}{sup 0}{pi}{sup 0} provides an improved understanding of the Y (2175) meson. A very precise study of the process e{sup +}e{sup -} {yields} {pi}{sup +}{pi}{sup -} improves the precision on the calculated anomalous magnetic moment of the muon and provides by far the best information on excited {rho} states. Our previous measurements of the timelike transition form factors (TFF) of the {eta} and {eta}' mesons at Q{sup 2} = 112 GeV{sup 2}, combined with new measurements of the their spacelike TFFs and those of the {pi}{sup 0} and {eta}{sub c} mesons, provide powerful tests of QCD and models of the distribution amplitudes of quarks inside these mesons. The {eta}{sub c} TFF shows the expected behavior over the Q{sup 2} range 1-50 GeV{sup 2}, and we are sensitive to next-to-leading-order QCD corrections. The {eta} and {eta}' TFFs are consistent with expected behavior, but those for the {pi}{sup 0} are not. Extracting the strange and nonstrange components of the {eta} and {eta}' TFFs, we find the nonstrange component to be consistent with theoretical expectations and inconsistent with the measured {pi}{sup 0} TFF.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Assessment of the Cast Stone Low-Temperature Waste Form Technology Coupled with Technetium Removal - 14379

The U.S. Department of Energy Office of Environmental Management (EM) is engaging the national laboratories to provide the scientific and technological rigor to support EM program and project planning, technology development and deployment, project execution, and assessment of program outcomes. As an early demonstration of this new responsibility, Pacific Northwest National Laboratory (PNNL) and Savannah River National Laboratory (SRNL) were chartered to implement a science and technology program addressing low-temperature waste forms for immobilization of DOE aqueous waste streams, including technetium removal as an implementing technology. As a first step, the laboratories examined the technical risks and uncertainties associated with the Cast Stone waste immobilization and technetium removal projects at Hanford. Science and technology gaps were identified for work associated with 1) conducting performance assessments and risk assessments of waste form and disposal system performance, and 2) technetium chemistry in tank wastes and separation of technetium from waste processing streams. Technical approaches to address the science and technology gaps were identified and an initial sequencing priority was suggested. A subset of research was initiated in 2013 to begin addressing the most significant science and technology gaps. The purpose of this paper is to report progress made towards closing these gaps and provide notable highlights of results achieved to date.

Cast Stone Low-Temperature Waste Form Technology C↗

Microstructure and Texture Evolutions in AISI 1050 Steel by Flow Forming

Hot rolled and annealed AISI 1050 steel cylindrical coupons were flow formed at different levels of deformation (66% and 90% wall thickness reduction). TEM studies revealed development of ultra fine (sub) grain cell structure due to severe plastic deformation. The transverse subgrain size changed from 10 m (beginning) to 300nm (66% deformation) to 40nm (90% deformation). EBSD study revealed decreased recrystallization fraction at 90% deformation compared with 66% deformation due to orientation pinning from preferred orientation along {002} planes. No evidence of dislocation pinning or cracking was observed on any samples. The aim of the present work is to study the deformation behaviour and microstructural evolution during conventional flow forming process. The study also sheds light on the strengthening behaviour and structural changes during severe straining.

Dynamic Recrystallization↗

Development of Cast Alumina-forming Austenitic Stainless Steel Alloys for use in High Temperature Process Environments

There is significant interest in the development of alumina-forming, creep resistant alloys for use in various industrial process environments. It is expected that these alloys can be fabricated into components for use in these environments through centrifugal casting and welding. Based on the successful earlier studies on the development of wrought versions of Alumina-Forming Austenitic (AFA) alloys, new alloy compositions have been developed for cast products. These alloys achieve good high-temperature oxidation resistance due to the formation of protective Al 2 O 3 scales while multiple second-phase precipitation strengthening contributes to excellent creep resistance. This work will summarize the results on the development and properties of a centrifugally cast AFA alloy. This paper highlights the strength, oxidation resistance in air and water vapor containing environments, and creep properties in the as-cast condition over the temperature range of 750°C to 900°C in a centrifugally cast heat. Preliminary results for a laboratory cast AFA composition with good oxidation resistance at 1100°C are also presented.

36 MATERIALS SCIENCE↗

Technoeconomic Benefits of Film-Forming Amine Products Applied to Steam Surface Condensers

In a conventional Rankine cycle, the majority of power plants employ surface condensers that use pumped cooling water to reject heat from the cycle. In such cases, heat rejection occurs in a shell and tube heat exchanger by film-wise condensation of low-pressure steam on stainless steel, titanium, brass, or copper-nickel tubing. To improve the thermal performance of steam surface condensers, a replenishable film-forming substance (FFS) can be ap-plied to the condenser tubing to promote efficient dropwise condensation. Conventionally, film-forming amine prod-uct (FFAP) coatings protect boiler surfaces from oxidative corrosion, which substantially reduces the operation and maintenance costs. To quantify the technical and economic benefits of FFAP coatings applied to condenser tubing due to the promotion of dropwise condensation, a thermal resistance network model was established. Using a rep-resentative steam surface condenser, the improvements in thermal performance (overall heat transfer coefficient) and process parameters (net plant efficiency, cooling water flowrate, and turbine backpressure) were determined due to the enhancement in the condensation heat transfer coefficient. Experimentally measured condensation heat transfer coefficients for common condenser materials were compared with the modeling results and were found to be within attainable bounds. Lastly, the trend in total heat exchanger cost reduction is generalized to understand the trade-off between reduced surface area for heat rejection and increase in coating application costs for a re-plenishable coating system.

20 FOSSIL-FUELED POWER PLANTS↗

Design Power Control Strategies of Grid-Forming Inverters for Microgrid Application: Preprint

This paper compares two control schemes in the application control layer of a non-PLL grid-forming (GFM) inverter to gain the insights and understanding of how the two schemes affect the dynamic responses of the GFM inverters and the transition operation of microgrids. Both schemes can achieve smooth microgrid transition operation and power tracking, however, the first scheme expects to exhibit more transients due to the feedforward of the inverse dynamic model of the output filter. Simulation results show that both control schemes achieve successful transition operation with smooth transients, and the second control scheme exhibits slightly better transients in the system frequency during islanding operation and the first one has slightly superior transients in the system frequency during reconnection operation. The power tracking performance in the grid-connected mode is evaluated, which shows that the first scheme has better active power tracking and the second one has better reactive power tracking. The analysis and results are useful to develop reliable control schemes for non-PLL GFM inverters because more and more inverters will work as non-PLL grid-forming sources in the future grids due to better stability and reliability.

grid-forming inverter↗

Small-Signal Stability Support from Dynamically Configurable Grid-Forming/Following Inverters for Distribution Systems: Preprint

As the penetration of inverter-based resources (IBRs) continues to increase in modern power systems, system stability is challenged by the insufficient inertia induced by IBRs; hence, there is a need to develop various methods to address the potential instabilities. In this paper, grid-forming (GFM) and grid-following (GFL) controls are implemented for inverters with flexible-mode transitions between them. The operation mode transition between GFM and GFL controls is adopted as an additional degree of control flexibility to adjust the small signal stability margin. Further, a holistic and detailed small signal model of the entire system with the dynamics from both synchronous generators (SGs) and IBRs is derived. The effectiveness of the proposed work in adjusting the system small signal stability margin is validated by conducting case studies with varying penetration levels of IBRs. A test system with one SG and five inverters was implemented in MATLAB/Simulink to demonstrate the effectiveness of the proposed approach. Index Terms - grid-following control, grid-forming control, operation mode transition, small-signal stability analysis

grid-following control↗

Modified Virtual Oscillator-Based Operation of Grid-Forming Converters with Single Voltage Sensor: Preprint

This paper proposes a virtual oscillator-based control architecture for a grid-forming converter with an inner current control loop. In general, the virtual oscillator is based on a Lienard type of oscillator equation with a cubic nonlinearity. A virtual oscillator alone cannot accommodate unbalanced or harmonic mitigation while operating converters in grid-forming mode. Therefore, to accomplish better tracking performance, incorporating the provision for nonlinear and/or unbalanced loads, an inner current control loop is utilized that is based on the Lyapunov energy function type control architecture. To reduce the overall cost of implementation and ensure proper phase difference in the generated voltages, the implemented virtual oscillator operates with only one voltage feedback from the point of common coupling. To verify the effectiveness of the proposed approach, the overall system has been modeled in MATTLAB/Simulink and PLECS domain. This paper also presents case studies showing the successful production of low harmonic load voltages under nonideal loading conditions, along with other important results.

dual second order generalized integrator↗