Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,729 records · Page 96

Multiscale investigation of the mechanism of biomass deconstruction in the dimethyl isosorbide/water Co-solvent pretreatment system

In the context of promoting a circular bioeconomy, the development of green and efficient lignocellulosic biomass pretreatment technologies so as to realize high value-added biomass utilization is of intense interest. We demonstrated the potential of the bio-based green solvent dimethyl isosorbide (DMI) for the fractionation of Eucalyptus biomass with excellent performance. Here, to investigate the mechanisms involved in biomass fractionation, microimaging and microspectroscopic techniques were employed together with molecular dynamics (MD) simulation and COSMO-RS quantum chemical calculations to derive multiscale information. Both the microstructure and regional chemistry of the cell wall vary significantly with the volume ratio of DMI/H 2 O. The strongest effects were found at DMI/H 2 O = 9:1 and showed visible cell wall tearing cracks and cell wall deformation and collapse as well as the lowest values of cell wall thickness and circularity. From the MD simulations, lignin exhibits collapsed-like structure in pure H 2 O with low solvent accessibility surface area (SASA) and radius of gyration (R g ). In contrast, lignin in DMI/H 2 O shows extended structure with high SASA and solvent interactions dominated by van der Waals forces, with maximal contact in the 9:1 (v/v) system. Further, the COSMO-RS calculated sigma (σ-) potential suggests the intermolecular interactions in DMI and DMI/H 2 O co-solvent are weak, leading to stronger interaction with lignin and correspondingly higher lignin dissolution. The radial distribution functions and σ-potential all show that again DMI/H 2 O at 9:1 is an optimal volume ratio for high lignin dissolution. Finally, this study provides a solvent-ratio dependent mechanism for the action of polar aprotic solvents in the deconstruction of biomass.

09 BIOMASS FUELS↗

Unraveling interphase-driven failure pathways in LiMn0.6Fe0.4PO4/graphite pouch cells

LiMnxFe1−xPO4 (LMFP) is a promising high-voltage, thermally stable, and earth-abundant cathode material, yet its practical application is limited by interphase instability and Mn dissolution. In this work, we systematically evaluate LiMn0.6Fe0.4PO4/graphite pouch cells using three electrolyte formulations including control carbonate electrolyte, control + 2 wt% vinylene carbonate (VC), and control + 2 wt% VC + 1 wt% 1,3,2-dioxathiolane 2,2-dioxide (DTD), to establish how electrolyte composition governs interphase chemistry and long-term degradation. Electrochemical testing shows that both additives are preferentially reduced prior to ethylene carbonate (EC) during cell formation, generating robust cathode-electrolyte interphase (CEI) and solid-electrolyte interphase (SEI) layers that suppress gas evolution and raise the first-cycle coulombic efficiency to 89.3%. Additionally, the dual-additive electrolyte delivers the most stable performance, retaining over 85% capacity after 600 cycles while minimizing impedance growth under long-term cycling at C/3 and 40 °C. Soft X-ray absorption spectroscopy confirms that VC + DTD effectively suppresses electrolyte oxidation at the cathode surface, and micro-X-ray fluorescence shows substantially reduced Mn dissolution and deposition on the graphite anode. Density functional theory simulations further provided insights into the structural and energetic influences of alkoxide species on the cathode surface, proposing a Mn2+ extraction mechanism. The combined experimental and computational findings establish a mechanistic link between electrolyte composition and interphase evolution, highlighting the effectiveness of electrolyte engineering for extending the operational lifetime of LMFP-based lithium-ion batteries.

Chak, Chanmonirath Michael↗

Solvent-mediated contaminant removal from plastic waste using thermodynamic modeling

Plastics recycling is hindered by the compositional complexity of plastic waste, which can include numerous polymer components as well as low concentrations of additives and non-intentionally added substances. These latter small-molecule species, which we collectively refer to as contaminants, can harm human health and will build up in recycled plastic causing environmental and downstream processing challenges if not removed. In this work, we present molecular modeling approaches using the COnductor-like Screening MOdel for Real Solvents (COSMO-RS) to guide the selection of solvents that are capable of removing targeted contaminants from plastic waste. By considering the thermodynamic partitioning of contaminant species between a solvent phase and polymer phase, we identify guidelines for solvent selection to promote either the low-temperature extraction of contaminants from plastic waste or the removal of contaminants as part of a dissolution-based plastics recycling process. We present four case studies to illustrate the application of the computational approach to the removal of brominated flame retardants, phthalates, and selected perfluoroalkyl substances, and compare to both literature and newly collected experimental data to illustrate model prediction accuracy. Furthermore, the case studies highlight the capability of the modeling approach to help design recycling processes that explicitly account for contaminant removal, thereby increasing product purity during dissolution-based recycling or facilitating chemical recycling of contaminant-free plastics.

Zhou, Panzheng [University of, Wisconsin, Madison,↗

Mechanistic understanding of carbon mineralization in fracture systems using microfluidics

Carbon mineralization in mafic and ultramafic rocks presents an opportunity for permanent carbon storage in the Earth's subsurface. However, due to their lower permeability, pre-existing fracture networks are key for mineralization to occur. Therefore, to fully develop this technology, a mechanistic understanding of the mineralization behavior in fractures with the consideration of hydrodynamic components is required. We use high-pressure microfluidics to investigate key mechanisms influencing dissolution–precipitation in a fracture network. The experiments were conducted in micromodels made of natural rocks with a comb-shaped flow channel to mimic a fracture network. This enabled studying the effect of injection rate on coupled dissolution–precipitation in advection and diffusion-dominated flow paths. We used gypsum carbonation as an analog reaction to allow for realistic experimental time frames due to its rapid reaction kinetics. The experimental work is coupled with high-fidelity numerical simulations to enhance our understanding of the parameters affecting the mineralization reaction. Our results demonstrate the importance of flow rate on the rate and nature of the gypsum carbonation reaction revealing that higher flow rates enable deeper penetration of the mineral precipitation front into the dead-end channels. This is an important finding since for sustained mineralization in a fracture network, precipitation in dead-ends while still allowing for flowing fractures is critical. Detailed characterization of the precipitates showed that lower flow rates led to porous and loose precipitates in the form of aragonite while higher flow rates mimicked supersaturation behavior leading to the formation of calcite. The reactive transport simulations further demonstrated the significance of flow velocity in advection-dominated channels to influence the efficiency of carbon mineralization in diffusion-dominated channels, potentially clogging of dead-end channels. These findings highlight the need for coupling chemical, mechanical, and hydrodynamic processes to evaluate the nature and extent of carbon mineralization in fractured media critical for permanent storage in mafic and ultramafic formations. This research further highlights the need for more investigation in potential subsurface fracture generation techniques to aid carbon mineralization.

25 ENERGY STORAGE↗

Atomic layer deposition of nickel sulfide thin films and their thermal and electrochemical stability

Nickel sulfides (NiS x ) show promise for a range of energy and other applications, but their (in)stability under processing and operating conditions is scarcely studied. Herein, we have developed a new NiS x atomic layer deposition process using an easily synthesized NiCl 2 (TMPDA) precursor (TMPDA = N,N,N′,N′-tetramethyl-1,3-propanediamine) with H 2 S. Thin films deposited at 165–225 °C consist mostly of the β-NiS phase and display low resistivity (∼40–120 μΩ cm), high purity (<3 at% impurities), and a rough morphology. The thermal stability of the NiS x thin films is studied using high-temperature X-ray diffraction, revealing that structural and compositional changes occur in reducing, inert, and oxidizing atmospheres at approximately 300–400 °C. Under electrochemical water splitting conditions, the films are unstable in acid due to dissolution, especially at oxidizing potentials. In an alkaline electrolyte, we do not observe Ni dissolution, but β-NiS transforms to Ni 3 S 2 under HER conditions, possibly supplemented with Ni and/or Ni(OH) 2 species. Under alkaline OER, all sulfur is lost and NiOOH is formed. In addition to offering an attractive, scalable route to the synthesis of NiS x thin films, our work highlights the importance of thermal and electrochemical (in)stability of sulfides as a crucial step for understanding and engineering materials for energy and other applications.

Mattinen, Miika [Univ. of Helsinki (Finland); Stan↗

Solubilization of PET in binary mixtures of HFIP and DCM

The dissolution of polyethylene terephthalate (PET) is a critical step for a solvent-based process, yet it typically requires highly corrosive or toxic solvents. Here, we investigate the solubilization and conformational behavior of PET in binary mixtures of hexafluoro-2-propanol (HFIP) and dichloromethane (DCM) as a strategy to reduce HFIP usage while maintaining effective dissolution. Small-angle neutron scattering (SANS) measurements reveal that PET remains molecularly dissolved in HFIP/DCM mixtures up to 50 vol% DCM. Analysis of PET chain conformations shows a transition from Gaussian behavior at low HFIP fractions to more swollen chains at intermediate compositions, accompanied by a counter-intuitive minimum in the radius of gyration at 50% HFIP. Complementary SANS measurements of the binary solvents demonstrate that compositional heterogeneity is maximized at this same solvent composition, suggesting a direct coupling between solvent microstructure and polymer dimensions. Molecular dynamics simulations corroborate the experimental findings, revealing solvent domain formation, preferential solvation of PET by HFIP, and a “caging” effect arising from solvent heterogeneity that leads to polymer coil compaction. Together, these results provide molecular-level insight into polymer behavior in mixed solvent systems and establish HFIP/DCM mixtures as a promising, more sustainable solvent platform for the PET post-process.

Arifuzzaman, Arif [ORNL]↗

Picolinate-based acyclic ligand for rare earth element extraction and separation

The rare earth elements (REEs) play an important role in many modern technologies, particularly those relevant to clean energy. Despite their increasing importance, obtaining them in elementally pure forms suitable for downstream applications is challenging due to their similar chemical properties. This problem has impeded efforts to efficiently and selectively extract them from end-of-life materials and electronic waste. Here, we report a cost-efficient acyclic picolinate-based chelator H 4 aapa. The REE stability constants (log K ML ) of this chelator were measured via pH potentiometric and UV-Visible spectrophotometric titrations, revealing it to preferably bind light over heavy REEs like many recently reported 18-membered macrocycles. Its REE complexes were characterized by X-ray crystallography and NMR spectroscopy, demonstrating that this chelator can attain different conformations. The unique properties of aapa were subsequently used to separate REEs via the dissolution of insoluble REE oxalate mixtures. This dissolution-based separation led to large separation factors, the most significant being that for the Ce 3+ /Lu 3+ pair (38.6) at pH 4. Leveraging the strong REE binding affinity of aapa, we further demonstrated this chelator can leach REEs from authentic end-of-life materials in the form of magnet waste and autocatalyst smelting (autocat) slag. With this approach, exposure of these materials to a 20 mM solution of aapa at neutral pH generates a metal-containing solution enriched in Nd 3+ and Dy 3+ by 56.9 wt% and 3.0 wt%, marking a 4-fold improvement over the use of 4 M HNO 3 .

Gao, Yangyang [University of California, Santa Bar↗

Leveraging Framework Instability: A Journey from Energy Storage to Drug Delivery

Amorphous pharmaceuticals often suffer from poor physical stability, which can negate their high solubility, fast dissolution rate, and better oral bioavailability vs. crystalline forms. This represents a major hurdle to processing, storage, and delivery of amorphous pharmaceuticals. Several approaches to addressing these problems have been pursued, but there is still a need for a general method for stabilizing the amorphous form. We describe a novel approach using a water-unstable metal-organic framework as a drug delivery vehicle that demonstrates improved amorphous form stability accompanied by remarkably enhanced solubility and a fast dissolution rate. This research project spanned eleven years from conception to realization and dissemination. With origins in understanding the stability or porous solids for energy storage materials, the work also highlights potential of basic science understanding to illuminate new areas of application.

Chemistry↗

Modeling Total Dissolved Gas for Optimal Operation of Multireservoir Systems

One important environmental issue of hydropower in the Columbia and Snake River Basins (Pacific Northwest region of United States) is elevated total dissolved gas (TDG) downstream of a dam, which has the potential to cause gas bubble disease in affected fish. Gas supersaturation in the Columbia River Basin primarily occurs due to dissolution of bubbles entrained during spill events. This paper presents a physically based TDG model that can be used to optimize spill operations in multireservoir hydropower systems. Independent variables of the model are forebay TDG, tailwater elevation, spillway and powerhouse discharges, project head, and environmental parameters such as temperature and atmospheric pressure. The model contains seven physically meaningful experimental parameters, which were calibrated and validated against TDG data collected downstream of Rock Island Dam (Washington) from 2008 to 2012. In conclusion, a sensitivity analysis was performed to increase the understanding of the relationships between TDG downstream of the dam and processes such as air entrainment, lateral powerhouse flow, and dissolution.

13 HYDRO ENERGY↗

Soft x-ray induced Ag diffusion in amorphous pulse laser deposited As{sub 50}Se{sub 50} thin films: An x-ray photoelectron and secondary ion mass spectroscopy study

In the present paper, x-ray photoelectron spectroscopy (XPS) is used to induce and study the Ag diffusion and dissolution in pulsed laser deposited As{sub 50}Se{sub 50} amorphous chalcogenide films. Dynamic secondary ion mass spectroscopy (SIMS) is also employed to investigate the Ag atomic concentration in depth. Dynamic SIMS measurements reveal that even before x-ray irradiation a considerable percentage of the total silver amount diffuses into the matrix forming an {approx}70 nm mixed Ag-Se-As layer. XPS analysis shows that x-ray irradiation induces further diffusion of silver into the chalcogenide matrix. At the end of the procedure silver is found to be homogeneously dissolved into the matrix leaving only a 5-7 nm thick surface layer with excess silver concentration. In this surface layer stable Ag{sub 2}Se clusters existing probably in quasicrystalline form prohibit further diffusion. The origin of the mechanism of the x-ray induced Ag diffusion and dissolution in amorphous chalcogenides is discussed in light of the present results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Automated High-Pressure Titration System with In Situ Infrared Spectroscopic Detection

A fully automated titration system with infrared detection was developed for investigating interfacial chemistry at high pressures. The apparatus consists of a high-pressure fluid generation and delivery system coupled to a high-pressure cell with infrared optics. A manifold of electronically actuated valves is used to direct pressurized fluids into the cell. Precise reagent additions to the pressurized cell are made with calibrated tubing loops that are filled with reagent and placed in-line with the cell and a syringe pump. The cell’s infrared optics facilitate both transmission and attenuated total reflection (ATR) measurements to monitor bulk-fluid composition and solid-surface phenomena such as adsorption, desorption, complexation, dissolution, and precipitation. Switching between the two measurement modes is accomplished with moveable mirrors that direct radiation from a Fourier transform infrared spectrometer into the cell along transmission or ATR light paths. The versatility of the high-pressure IR titration system is demonstrated with three case studies. First, we titrated water into supercritical CO2 (scCO2) to generate an infrared calibration curve and determine the solubility of water in CO2 at 50 °C and 90 bar. Next, we characterized the partitioning of water between a montmorillonite clay and scCO2 at 50 °C and 90 bar. Transmission-mode spectra were used to quantify changes in the clay’s sorbed water concentration as a function of scCO2 hydration, and ATR measurements provided insights into competitive residency of water and CO2 on the clay surface and in the interlayer. Finally, we demonstrated how time-dependent studies can be conducted with the system by monitoring the carbonation reaction of forsterite (Mg2SiO4) in water-bearing scCO2 at 50 °C and 90 bar. Immediately after water dissolved in the scCO2, a thin film of adsorbed water formed on the mineral surface, and the film thickness increased with time as the forsterite began to dissolve. However, after approximately 2.5 hours, the trend reversed, and a carbonate precipitate began to form on the forsterite surface, exposing dramatic chemical changes in the thin-water film. Collectively, these applications illustrate how the high-pressure IR titration system can provide molecular-level information about the interactions between variably wet scCO2 and minerals relevant to underground storage of CO2 (geologic carbon sequestration). The apparatus could also be utilized to study high-pressure interfacial chemistry in other areas such as catalysis, polymerization, food processing, and oil and gas recovery.

Environmental Molecular Sciences Laboratory↗

Probe Mössbauer spectroscopy of mechanical alloying in binary Cr‐{sup 57}Fe(1 at%) system

Solid state reactions during mechanical alloying (MA) in a binary mixture of powdered Cr and {sup 57}Fe in atomic ratio of 99:1 have been studied using {sup 57}Fe Mössbauer spectroscopy, X-ray diffraction and Auger spectrometry. The proposed model of MA includes formation of Cr(Fe){sub x}O{sub y} oxides at the contact places of Cr and Fe particles, formation of nanostructure with simultaneous dissolution of the oxides, penetration of Fe atoms along grain boundaries in close-to-boundary distorted zones of interfaces in a substitutional position, formation of the substitutional solid solution of Fe in Cr in the body of grains. It was shown that the increase in the BCC lattice parameter on increasing the milling time is due to the dissolution of oxides and formation of interstitial solid solution of O in Cr. There were established substantial differences in consumption of BCC Fe in a Mg → Al → Si → Cr sequence due to the major role of chemical interaction of Mg(Al,Si,Cr) with Fe.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evolution of iron-containing defects during processing of Si solar cells

The formation of iron-containing defects was studied during the fabrication process of a Si solar cell. Three Cz-Si crystals with different iron content in the feedstock were grown for the study. Iron-containing defects in and near-to the n{sup +}p-junction volume (NJV) of the cells are formed directly after phosphorus diffusion due to an inflow of iron atoms from the dissolving iron-silicide precipitates. These NJV-defects strongly affect the dark saturation current of the junctions. Partial dissolution or gettering of the NJV-defects during formation of the antireflection coating is accompanied by an increase in defect concentrations in the bulk of the cell. Further deterioration of bulk carrier lifetime during the formation of electrical contacts is related to the partial dissolution of remaining iron-silicide precipitates during the firing process. A general description of the defect evolution in iron-contaminated wafers during solar cell processing is presented and possible strategies for reducing the influence of iron-containing defects are proposed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Synchrotron-based investigation of transition-metal getterability in n-type multicrystalline silicon

Solar cells based on n-type multicrystalline silicon (mc-Si) wafers are a promising path to reduce the cost per kWh of photovoltaics; however, the full potential of the material and how to optimally process it are still unknown. Process optimization requires knowledge of the response of the metal-silicide precipitate distribution to processing, which has yet to be directly measured and quantified. To supply this missing piece, we use synchrotron-based micro-X-ray fluorescence (μ-XRF) to quantitatively map >250 metal-rich particles in n-type mc-Si wafers before and after phosphorus diffusion gettering (PDG). We find that 820°C PDG is sufficient to remove precipitates of fast-diffusing impurities and that 920°C PDG can eliminate precipitated Fe to below the detection limit of μ-XRF. Thus, the evolution of precipitated metal impurities during PDG is observed to be similar for n- and p-type mc-Si, an observation consistent with calculations of the driving forces for precipitate dissolution and segregation gettering. Measurements show that minority-carrier lifetime increases with increasing precipitate dissolution from 820°C to 880°C PDG, and that the lifetime after PDG at 920°C is between the lifetimes achieved after 820°C and 880°C PDG.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Exploring chemical speciation at electrified interfaces using detailed continuum models

We present a local free-energy functional-based generic continuum model for material interfaces with a specific emphasis on electrified solid/liquid interfaces. The model enables a description of multicomponent phases at interfaces and includes the effects of specific non-electrostatic interactions (specific adsorption), ion size disparity, and the explicit presence of neutral species. In addition to the optimization of electrostatic, non-electrostatic, and steric forces, the model can be easily modified to explore the effects of other channels for equilibration, including local chemical transformations driven by equilibrium constants and electrochemical reactions driven by the electrode potential. In this way, we show that, upon accounting for these effects, local speciation in the vicinity of the interface can be drastically different from what is expected from restricted models and minor species (from the bulk perspective) may become dominant due to the effects of local pH. We evaluate the ionic contribution to the surface tension at the interface and show how this could impact the structure of air/liquid interfaces. On the same footing, an attempt to describe electrochemical metal dissolution is made. The model allows estimates of the mutual population of newly produced ions depending on their charge and size and could be useful for interpretation of electrochemical and spectroscopic measurements if the dissolution involves different metal ions (species). With these advances, the proposed model may be used as an ingredient within a hybrid ab initio-continuum methodology to model biased interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recent advances in polysulfide mediation of lithium-sulfur batteries via facile cathode and electrolyte modification

Lithium-sulfur (Li-S) batteries have garnered immense interest due to their potential to surpass the energy densities of state-of-the-art lithium-ion batteries. However, severe technical problems of polysulfide dissolution and shuttle effect still prohibit the commercialization of Li-S batteries. This review focuses on the recent advances of polysulfide mediation in conventional Li-S batteries with liquid electrolytes. Simple yet effective solutions to control polysulfide dissolution and shuttling via facile modification of the cathode and the electrolyte are highlighted. The rational design of cathode composition, the use of polysulfide barrier layers, and the selection of electrolyte components are discussed. These strategies offer significant promise to address the challenges and increase the viability of the large-scale application of Li-S batteries.

25 ENERGY STORAGE↗

The growth and nanothermite reaction of 2Al/3NiO multilayer thin films

Nanothermite NiO–Al is a promising material system for low gas emission heat sources; still, its reactive properties are highly dependent on material processing conditions. In the current study, sputter deposition is used to fabricate highly controlled nanolaminates comprised of alternating NiO and Al layers. Films having an overall stoichiometry of 2Al to 3NiO were produced with different bilayer thicknesses to investigate how ignition and self-sustained, high temperature reactions vary with changes to nanometer-scale periodicity and preheat conditions. Ignition studies were carried out with both hot plate and laser irradiation and compared to slow heating studies in hot-stage x-ray diffraction. Ignition behavior has bilayer thickness and heating rate dependencies. The 2Al/3NiO with λ ≤ 300 nm ignited via solid/solid diffusion mixing (activation energy, E a = 49 ± 3 kJ/mole). Multilayers having λ ≥ 500 nm required a more favorable mixing kinetics of solid/liquid dissolution into molten Al (E a = 30 ± 4 kJ/mole). This solid/liquid dissolution E a is a factor of 5 lower than that of the previously reported powder compacts due to the elimination of a passivating Al oxide layer present on the powder. The reactant mixing mechanism between 300 and 500 nm bilayer thicknesses was dependent on the ignition source's heating rate. The self-propagating reaction velocities of 2Al/3NiO multilayers varied from 0.4 to 2.5 m/s. Pre-heating nanolaminates to temperatures below the onset reaction temperatures associated with forming intermediate nickel aluminides at multilayer interfaces led to increased propagation velocities, whereas pre-heating samples above the onset temperatures inhibited subsequent attempts at laser ignition.

36 MATERIALS SCIENCE↗

Large-scale molecular dynamics simulations of bubble collapse in water: Effects of system size, water model, and nitrogen

Molecular dynamics simulations in the microcanonical ensemble are performed to study the collapse of a bubble in liquid water using the single-site mW and the four-site TIP4P/2005 water models. To study system size effects, simulations for pure water systems are performed using periodically replicated simulation boxes with linear dimensions, L, ranging from 32 to 512 nm with the largest systems containing 8.7 × 10 6 and 4.5 × 10 9 molecules for the TIP4P/2005 and mW water models, respectively. The computationally more efficient mW water model allows us to reach converging behavior when the bubble dynamics results are plotted in reduced units, and the limiting behavior can be obtained through linear extrapolation in L –1 . Qualitative differences are observed between simulations with the mW and TIP4P/2005 water models, but they can be explained by the models’ differences in predicted viscosity and surface tension. Although bubble collapse occurs on time scales of only hundreds of picoseconds, the system sizes used here are sufficiently large to obtain bubble dynamics consistent with the Rayleigh–Plesset equation when using the models’ thermophysical properties as input. For the conditions explored here, extreme heating of the interfacial water molecules near the time of collapse is observed for the larger mW water systems (but the model underpredicts the viscosity), whereas heating is less pronounced for the TIP4P/2005 water systems because its larger viscosity contribution slows the collapse dynamics. The presence of nitrogen within the bubble only starts to affect bubble dynamics near the very end of the initial collapse, leading to an incomplete collapse and strong rebound for the mW water model. Although nitrogen is non-condensable at 300 K, it becomes highly compressed and reaches a liquid-like density near the collapse point. We find that the dissolution of nitrogen is much slower than the movement of the collapsing water front, and the re-expansion of the dense nitrogen droplet gives rise to bubble rebound. The incompatibility of the collapse and dissolution time scales should be considered for continuum-scale modeling of bubble dynamics. Finally, we also confirm that the diffusion coefficient for dissolved nitrogen is insensitive to pressure as the liquid transitions from a compressed to a stretched state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗