Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wave data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Utah FORGE: Fault Shear Reactivation Experimental Data for Fluid Injection-Rate Controls on Seismic Moment

Included are experimental data recorded from shear experiments that specifically explore the link between fluid-injection rate and seismic moment resulting from shear reactivation of laboratory faults. Raw mechanical data from three experiments are included alongside corresponding MATLAB scripts that import and plot the data, as well as use it to calculate shear and normal stress. Experiments are performed on 2.5-3 inch long granitoid cores from the Utah FORGE EGS demonstration site, containing a single inclined fracture with small-scale roughness added to the fracture surface. The raw data included here were recorded from an aluminum triaxial pressure vessel (TEMCO) configured with three independent servo-controlled pumps, with distilled water used as the working fluid. The pumps control confining pressure, upstream pore pressure, and axial pressure, with each pump connected to a LabView interface to record applied pressures, cumulative injected water volumes, and pump flow rates. The downstream outlet from the fracture is closed to allow pressurization, which is measured by an external pressure transducer. A linear variable differential transformer (LVDT) attached to the axial piston measures axial displacement, from which we calculate shear displacement along the fracture. Additionally, P-wave transducers are used to record acoustic signatures, where acoustic emission events and maximum amplitudes are compared against seismic moment and shear slip velocity. Fluid injection rates range between 0.05 mL/min, 0.25 mL/min, and 0.75 mL/min for each experiment. Along-fault pressure distributions are progressively less uniform as injection rates increase, representing a switch from steady-state to transient conditions. Triggered shear displacement is used as a proxy for seismic moment and is indexed against cumulative injection volume and rate. Each experiment is performed under constant shear stress conditions, and the sample is fully saturated with DI water. Axial and confining stresses are applied to 3 MPa through pressure-stepping in 500 kPa increments. The pore pressure is held constant at 200 kPa prior to initiating the experiment, and initial axial displacement is recorded. The axial stress is then increased to initiate shear mobilization during the loading phase (run-in) until a peak steady state is achieved. The initial shear stress is reduced to approximately 80% of the peak shear stress by decreasing the axial stress, then held constant for the duration of each experiment.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

A dark siren measurement of the Hubble constant using gravitational wave events from the first three LIGO/Virgo observing runs and DELVE

The current and next observation seasons will detect hundreds of gravitational waves (GWs) from compact binary systems coalescence at cosmological distances. When combined with independent electromagnetic measurements, the source redshift will be known, and we will be able to obtain precise measurements of the Hubble constant H_0 via the distance–redshift relation. However, most observed mergers are not expected to have electromagnetic counterparts, which prevents a direct redshift measurement. In this scenario, one possibility is to use the dark sirens method that statistically marginalizes over all the potential host galaxies within the GW location volume to provide a probabilistic source redshift. Here we presented H_0 measurements using two new dark sirens compared to previous analyses using DECam data: GW190924|$\_$|021846 and GW200202|$\_$|154313. The photometric redshifts of the possible host galaxies of these two events are acquired from the DECam Local Volume Exploration Survey (DELVE) carried out on the Blanco telescope at Cerro Tololo. The combination of the H_0 posterior from GW190924|$\_$|021846 and GW200202|$\_$|154313 together with the bright siren GW170817 leads to |$H_{0} = 68.84^{+15.51}_{-7.74}\, \rm {km\, s^{-1}\, Mpc^{-1}}$|⁠. Including these two dark sirens improves the 68 per cent confidence interval (CI) by 7 per cent over GW170817 alone. This demonstrates that the addition of well-localized dark sirens in such analysis improves the precision of cosmological measurements. Using a sample containing 10 well-localized dark sirens observed during the third LIGO/Virgo observation run, without the inclusion of GW170817, we determine a measurement of |$H_{0} = 76.00^{+17.64}_{-13.45}\, \rm {km\, s^{-1}\, Mpc^{-1}}$|⁠.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Lossy compression of statistical data using quantum annealer

Abstract We present a new lossy compression algorithm for statistical floating-point data through a representation learning with binary variables. The algorithm finds a set of basis vectors and their binary coefficients that precisely reconstruct the original data. The optimization for the basis vectors is performed classically, while binary coefficients are retrieved through both simulated and quantum annealing for comparison. A bias correction procedure is also presented to estimate and eliminate the error and bias introduced from the inexact reconstruction of the lossy compression for statistical data analyses. The compression algorithm is demonstrated on two different datasets of lattice quantum chromodynamics simulations. The results obtained using simulated annealing show 3–3.5 times better compression performance than the algorithm based on neural-network autoencoder. Calculations using quantum annealing also show promising results, but performance is limited by the integrated control error of the quantum processing unit, which yields large uncertainties in the biases and coupling parameters. Hardware comparison is further studied between the previous generation D-Wave 2000Q and the current D-Wave Advantage system. Our study shows that the Advantage system is more likely to obtain low-energy solutions for the problems than the 2000Q.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Behavior and mechanisms of Doppler wind lidar error in complex terrain: stable flow case study at Perdigão

A numerical experiment is carried out investigating the magnitude of biases in ground-based lidar measurements in complex flow conditions. Biases assessed include those arising from flow curvature and from the interaction of turbulence with the wind field reconstruction (WFR) algorithms used by a WindCube lidars and anemometers. RANS-CFD and WRF-LES simulations were performed for the Perdig˜ao Field Experiment site for a range of atmospheric conditions. Virtual anemometer and lidar data were generated for four locations: two near exposed ridge tops and two in low-speed regions in the valley. The LES data at these four locations show that the scalar inflation terms (the relation between scalar and vector averaged wind speed) for virtual lidar and virtual cups agree very well with predictions using perturbation theory. While the lidar errors vary greatly with location and height, the contribution from the flow curvature tends to be larger than the differences arising from scalar inflation. For one lidar/mast pair near the ridge top, comparisons between simulations and measurements are carried out for a resonant mountain wave event on June 14th, 2017, and for the whole duration of the Perdigão campaign for winds perpendicular to the ridges. The lidar error during the mountain wave, a period of strong stability and low inversion height, is significantly larger than the campaign average. The sensitivity of the lidar error to atmospheric stability is confirmed by the RANS simulations, which suggests strong sensitivity of flow curvature error to stability conditions and to the shape of the wind speed profile near the top of the boundary layer.

17 WIND ENERGY↗
DOE OSTI2021

Electronic nature of chiral charge order in the kagome superconductor CsV 3 Sb 5

Kagome superconductors with T C up to 7 K have been discovered for over 40 y. Recently, unconventional chiral charge order has been reported in kagome superconductor KV 3 Sb 5 , with an ordering temperature of one order of magnitude higher than the T C . However, the chirality of the charge order has not been reported in the cousin kagome superconductor CsV 3 Sb 5 , and the electronic nature of the chirality remains elusive. In this paper, we report the observation of electronic chiral charge order in CsV 3 Sb 5 via scanning tunneling microscopy (STM). We observe a 2 × 2 charge modulation and a 1 × 4 superlattice in both topographic data and tunneling spectroscopy. 2 × 2 charge modulation is highly anticipated as a charge order by fundamental kagome lattice models at van Hove filling, and is shown to exhibit intrinsic chirality. We find that the 1 × 4 superlattices form various small domain walls, and can be a surface effect as supported by our first-principles calculations. Crucially, we find that the amplitude of the energy gap opened by the charge order exhibits real-space modulations, and features 2 × 2 wave vectors with chirality, highlighting the electronic nature of the chiral charge order. STM study at 0.4 K reveals a superconducting energy gap with a gap size 2Δ = 0.85 meV, which estimates a moderate superconductivity coupling strength with 2Δ/k B T C = 3.9. Furthermore, when further applying a c-axis magnetic field, vortex core bound states are observed within this gap, indicative of clean-limit superconductivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Cylinder Test

In 1941 G.I. Taylor proposed the cylinder test as an experiment to determine the properties of explosive products. The test consists of a hollow metal cylinder containing an unreacted cylindrical charge of explosives. The charge is detonated at one end of the cylinder and, as the detonation wave propagates, the product gas expands behind it. As the product gas is produced, the pressure acting on the metal increases and begins to push the walls outward. Consider the time at which the detonation wave has reached the halfway point between the two ends of the cylinder. In front of the wave nothing has changed and the metal tube has the same initial radius. Behind the wave, the radius of the tube has expanded. The farther behind the wave a section of tube is, the larger its radius has become. The longer the wall is exposed to the pressurized gas, the more it expands, so that the radius is largest where the detonation was initiated. The metal most commonly used for this experiment is soft copper. Its material properties are well known and soft copper is also easy to shape with precision machining. During the cylinder test the radial expansion of the cylinder is measured over time and this data is used to determine the amount of work applied to the cylinder wall by the product gas as a function of time. Since volume increases in this problem, the time dependence can be seen as a volume dependence. The volume dependent work yields a path in thermodynamic space. The cylinder test experiment can be modeled using simulation. The simulation gives you the answer, but it cannot tell you why. The goal of the proposed work is to use analytic analysis methods to give insight into the simulation solution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation of Plasma Emission in Magnetized Plasmas

The recent Parker Solar Probe observations of type III radio bursts show that the effects of the finite background magnetic field can be an important factor in the interpretation of data. In the present paper, the effects of the background magnetic field on the plasma-emission process, which is believed to be the main emission mechanism for solar coronal and interplanetary type III radio bursts, are investigated by means of the particle-in-cell simulation method. The effects of the ambient magnetic field are systematically surveyed by varying the ratio of plasma frequency to electron gyrofrequency. The present study shows that for a sufficiently strong ambient magnetic field, the wave–particle interaction processes lead to a highly field-aligned longitudinal mode excitation and anisotropic electron velocity distribution function, accompanied by a significantly enhanced plasma emission at the second-harmonic plasma frequency. For such a case, the polarization of the harmonic emission is almost entirely in the sense of extraordinary mode. On the other hand, for moderate strengths of the ambient magnetic field, the interpretation of the simulation result is less clear. The underlying nonlinear-mode coupling processes indicate that to properly understand and interpret the simulation results requires sophisticated analyses involving interactions among magnetized plasma normal modes, including the two transverse modes of the magneto-active plasma, namely, the extraordinary and ordinary modes, as well as electron-cyclotron-whistler, plasma oscillation, and upper-hybrid modes. At present, a nonlinear theory suitable for quantitatively analyzing such complex-mode coupling processes in magnetized plasmas is incomplete, which calls for further theoretical research, but the present simulation results could provide a guide for future theoretical efforts.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

How an Autonomous Offshore Power System Can Transform the Ocean Economy - A Hypothetical Case Study Utilizing an Autonomous Offshore Power System in Northern Lights Carbon Capture and Storage Project

An Autonomous Offshore Power System (AOPS) provides in-situ power, energy storage, real-time data and communications support, asset management, and other capabilities at sea. It has applications for all offshore industries: energy, defense and security, aquaculture, science and research, and communications. Furthermore, this paper highlights how an AOPS can reduce cost, complexity, and carbon-intensity for existing offshore operations and enable new capabilities for offshore industry leaders. This new AOPS technology has two primary advantages. First, it unlocks the autonomous, electric future of the ocean economy via ‘local’ power generation and energy storage, in addition to real-time connection to the data cloud. Second, it helps enable a material change in the global energy mix through cost-effective, reliable generation and storage technology for use cases including mobile/static data-gathering and reporting systems, operating equipment, and charging networks for uncrewed surface vessels. AOPS technology will help transform the ocean economy, and thus has implications for offshore industry leaders as they push to reduce costs today and make an autonomous and decarbonized future possible.

16 TIDAL AND WAVE POWER↗
DOE OSTI2023

Investigating Marine Environmental Degradation of Additive Manufacturing Materials for Renewable Energy Applications: Preprint

Marine renewable energy is a relatively young industry where there is a great need for rapid prototyping in design-build-test campaigns to quickly mature groundbreaking technologies. Additive manufacturing has an important role to play in the industry; however, little information is available to marine energy developers to help inform them on which additive manufacturing materials are appropriate for harsh marine environments. This paper presents an initial study on the mechanical characterization of polymeric additive manufacturing materials and the degradation effects of marine environments. Ultem 9085, acrylonitrile styrene acrylate, and chopped carbon-filled nylon, as well as continuous carbon and glass fiber-reinforced nylon were chosen for this study. Samples were manufactured to perform a variety of tension, shear, and compression mechanical characterization tests on the materials. Half of the samples were conditioned in Pacific Ocean water for approximately 6 months at Pacific Northwest National Laboratory's Marine Sciences Laboratory before being returned for mechanical characterization. The mechanical testing results showed that the Ultem 9085 and acrylonitrile styrene acrylate materials experienced little to no degradation in stiffness or strength after exposure to the marine environment. On the other hand, the nylon-based materials suffered significant stiffness and strength degradation (over 50% in some cases) after environmental conditioning. Ultimately, these data sets should serve as starting points to allow marine renewable energy developers to make informed additive manufacturing material choices for their prototype deployments.

additive manufacturing↗
DOE OSTI2024

NbZr_BCC_SolidSolution_128atoms_VASP6

We performed density functional theory (DFT) calculations for body-centered-cubic (BCC) structures with 128 lattices sites of solid solution binary alloys niobium-zirconium (Nb-Zr). The electronic structures of alloys have been calculated using Vienna Ab initio Simulation Package (VASP). Within this package the DFT approach is used to reduce many-body Schrodinger equation to set of single particle Kohn-Sham (KS) equations. The generalized electronic exchange-correlation functional is described by generalized gradient approximation with the Perdew-Burke-Ernzerhof parametrization. The electron-ion interactions is described by pseudopotentials developed within the plane-wave basis projector augmented-wave (PAW) approach \cite{PAW}. These pseudopotentials are available at the VASP portal (http://cms.mpi.univie.ac.at/vasp/). Our calculations have been run with the pseudopotentials treating s and p semi-core states as valence in case for the elements Nb and Zr. The electronic densities and potentials are expanded over plane-waves with energy cutoff of 350 eV. 2x2x2 k-mesh and normal precision were used. The alloys were modeled by supercell containing 128 randomly distributed atoms. At initial step the atoms occupy perfect bcc lattice cites. This initial structure was optimized until energy changes less than 1e-6 eV, while forces acting on atoms don't exceed 1e-2 eV/angstrom. The electron-ion interaction is described by PAW pseudopotentials. The calculations have been collected by sampling chemical compositions across the entire compositional range. The chemical compositions have been sampled by progressively changing the number of atoms per constituent by 4. For each chemical composition of binaries and ternaries, the first-principle calculations have been run for 100 randomized arrangements of the constituents on the BCC lattice sites. We collected data for a total of 3,100 randomized atomic structures over 31 chemical compositions. The calculations have been collected on NERSC-Perlmutter and OLCF-Summit using the VASP 6.3.2. The VASP calculations for every atomic structure have been performed in 2 main steps: 1. Starting from an ideal body-centered-cubic (BCC) structure, geometry optimization with low precision has been executed to perform a preliminary optimization of the atomic structure. The output for this calculations is available in the files 0.CONTCAR, 0.OUTCAR, rlx1.out. 2. Using the atomic structure resulting from the preliminary geometry optimization, a second geometry optimization has been performed using normal precision. The output for this calculations is available in the files CONTCAR, OUTCAR, rlx2.out, vaspout.h5, and vasprun.xml. Cases 1-10 have been run without generating the file 'vaspout.h5'. Every chemical composition sampled across the composition range in the dataset has its own directory. The convention used to name the directories for binary alloys is AXBY, where A and B refer to the constituents, whereas X and Y are positive integers that represent the number of atoms for each constituent and their values still sum up to 128. Each atomic structure associated with a specific chemical composition has its own sub-directory within the directory of the corresponding chemical composition. The sub-directories for each atomic structure for each chemical composition are named 'case-*', where * is a positive integer that spans all the values from 1 through 100, extremes included. The files contained in each sub-directory 'case-*' for each atomic structure are as follows: FILES contained in each subdirectory with name "case-N" where N ranges between 11 and 100, extremes included: 1. INCAR: input file that contains various parameters and settings for controlling the behavior of the electronic structure calculations 2. KPOINTS: input file that specifies the Bloch vectors (k points) used to sample the Brillouin zone 3. 0.POSCAR: input file that defines the atomic structure of a system 4. 0.CONTCAR: output file that provides the atomic positions and cell parameters after the first geometry optimization has been run with the precision variable set to PREC=Low in the INCAR file 5. 0.OUTCAR: output file that contains detailed information about the progress of a calculation after the first geometry optimization has been run with the precision variable set to PREC=Low in the INCAR file 6. rlx1.out: file with diagnostic information about the execution of the first geometry optimization with precision variable set to PREC=Low in the INCAR file 7. POSCAR: input file that defines the atomic structure of a system after the first geometry optimization has been run at low precision. This represents the input for the second geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 8. CONTCAR: output file that provides the atomic positions and cell parameters after the second geometry optimization has been run with the precision variable set to PREC=Normal in the INCAR file 9. OUTCAR: output file that contains detailed information about the progress of a calculation after the second geometry optimization has been run with the precision variable set to PREC=Normal in the INCAR file 10. rlx2.out: file with diagnostic information about the execution of the second geometry optimization with precision variable set to PREC=Normal in the INCAR file 11. vaspout.h5: hierarchical HDF5 file containing the inputs and outputs of a VASP calculation. To analyze the data in this file we recommend using py4vasp. This file is only produced if the VASP version used is compiled with HDF5 support 12. vasprun.xml: contains similar information to OUTCAR, but in an xml format. 13. CHGCAR: contains the charge density data of a system. This data is crucial for analyzing electronic structures, calculating electrostatic potential, and studying the distribution of charge in a crystal or molecular system FILES contained in each subdirectory with name "case-N" where N ranges between 1 and 10, extremes included: 1. INCAR: input file that contains various parameters and settings for controlling the behavior of the electronic structure calculations 2. KPOINTS: input file that specifies the Bloch vectors (k points) used to sample the Brillouin zone 3. {ID}.POSCAR: input file that defines the atomic structure of a system at the beginning of ID execution of geometry optimization with PREC=LOW 4. {ID}.CONTCAR: output file that provides the atomic positions and cell parameters at the end of ID execution of geometry optimization with PREC=LOW in the INCAR file 5. {ID}.OUTCAR: output file that contains detailed information about the progress of a calculation after the ID execution of geometry optimization that has been run with the precision variable set to PREC=Low in the INCAR file 6. rlx1.{ID}.out: file with diagnostic information about the execution of the ID execution of the geometry optimization with precision variable set to PREC=Low in the INCAR file 7. N{ID}.POSCAR: input file that defines the atomic structure of a system after the geometry optimization run at low precision. This represents the input for the ID execution of the second geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 8. N{ID}.CONTCAR: output file that provides the atomic positions and cell parameters after the ID execution of the geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 9. N{ID}.OUTCAR: output file that contains detailed information about the progress of a calculation after the ID execution of the geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 10. rlx2.{ID}.out: file with diagnostic information about the ID execution of geometry optimization with precision variable set to PREC=Normal in the INCAR file 11. vaspout.h5: hierarchical HDF5 file containing the inputs and outputs of a VASP calculation. To analyze the data in this file we recommend using py4vasp. This file is only produced if the VASP version used is compiled with HDF5 support 12. vasprun.xml: contains similar information to OUTCAR, but in an xml format. 13. CHGCAR: contains the charge density data of a system. This data is crucial for analyzing electronic structures, calculating electrostatic potential, and studying the distribution of charge in a crystal or molecular system This research is sponsored by the Artificial Intelligence Initiative as part of the Laboratory Directed Research and Development (LDRD) Program of Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the US Department of Energy under contract DE-AC05-00OR22725. This work used resources of the Oak Ridge Leadership Computing Facility, which is supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC05-00OR22725, under Directorate Discretionary awards MAT025 (Materials Science) and LRN026 (Machine Learning), and INCITE award MAT201. This work also used resources of the National Energy Research Scientific Computing Center, which is supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231, under award ERCAP0025216. REFERENCES (1) Kresse, G. & Hafner, J. Ab initio molecular dynamics for liquid metals. Phys. review B 47, 558 (1993). (2) Kresse, G. & Hafner, J. Ab initio molecular-dynamics simulation of the liquid-metal–amorphous-semiconductor transition in germanium. Phys. Rev. B 49, 14251 (1994) (3) Kresse, G. & Furthmüller, J. Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set. Comput. materials science 6, 15–50 (1996) (4) Kresse, G. & Furthmüller, J. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set. Phys. review B 54, 11169 (1996) (5) Kresse, G. & Joubert, D. From ultrasoft pseudopotentials to the projector augmented-wave method. Phys. review b 59, 1758 (1999)

36 MATERIALS SCIENCE↗
DOE OSTI2024

TaZr_BCC_SolidSolution_128atoms_VASP6

We performed density functional theory (DFT) calculations for body-centered-cubic (BCC) structures with 128 lattices sites of solid solution binary alloys tantalum-zirconium (Ta-Zr). The electronic structures of alloys have been calculated using Vienna Ab initio Simulation Package (VASP). Within this package the DFT approach is used to reduce many-body Schrodinger equation to set of single particle Kohn-Sham (KS) equations. The generalized electronic exchange-correlation functional is described by generalized gradient approximation with the Perdew-Burke-Ernzerhof parametrization. The electron-ion interactions is described by pseudopotentials developed within the plane-wave basis projector augmented-wave (PAW) approach \cite{PAW}. These pseudopotentials are available at the VASP portal (http://cms.mpi.univie.ac.at/vasp/). Our calculations have been run with the pseudopotentials treating s and p semi-core states as valence in case for the elements Ta and Zr. The electronic densities and potentials are expanded over plane-waves with energy cutoff of 350 eV. 2x2x2 k-mesh and normal precision were used. The alloys were modeled by supercell containing 128 randomly distributed atoms. At initial step the atoms occupy perfect bcc lattice cites. This initial structure was optimized until energy changes less than 1e-6 eV, while forces acting on atoms don't exceed 1e-2 eV/angstrom. The electron-ion interaction is described by PAW pseudopotentials. The calculations have been collected by sampling chemical compositions across the entire compositional range. The chemical compositions have been sampled by progressively changing the number of atoms per constituent by 4. For each chemical composition of binaries and ternaries, the first-principle calculations have been run for 100 randomized arrangements of the constituents on the BCC lattice sites. We collected data for a total of 3,100 randomized atomic structures over 31 chemical compositions. The calculations have been collected on NERSC-Perlmutter and OLCF-Summit using the VASP 6.3.2. The VASP calculations for every atomic structure have been performed in 2 main steps: 1. Starting from an ideal body-centered-cubic (BCC) structure, geometry optimization with low precision has been executed to perform a preliminary optimization of the atomic structure. The output for this calculations is available in the files 0.CONTCAR, 0.OUTCAR, rlx1.out. 2. Using the atomic structure resulting from the preliminary geometry optimization, a second geometry optimization has been performed using normal precision. The output for this calculations is available in the files CONTCAR, OUTCAR, rlx2.out, vaspout.h5, and vasprun.xml. Cases 1-10 have been run without generating the file 'vaspout.h5'. Every chemical composition sampled across the composition range in the dataset has its own directory. The convention used to name the directories for binary alloys is AXBY, where A and B refer to the constituents, whereas X and Y are positive integers that represent the number of atoms for each constituent and their values still sum up to 128. Each atomic structure associated with a specific chemical composition has its own sub-directory within the directory of the corresponding chemical composition. The sub-directories for each atomic structure for each chemical composition are named 'case-*', where * is a positive integer that spans all the values from 1 through 100, extremes included. The files contained in each sub-directory 'case-*' for each atomic structure are as follows: FILES contained in each subdirectory with name "case-N" where N ranges between 11 and 80, extremes included: 1. INCAR: input file that contains various parameters and settings for controlling the behavior of the electronic structure calculations 2. KPOINTS: input file that specifies the Bloch vectors (k points) used to sample the Brillouin zone 3. 0.POSCAR: input file that defines the atomic structure of a system 4. 0.CONTCAR: output file that provides the atomic positions and cell parameters after the first geometry optimization has been run with the precision variable set to PREC=Low in the INCAR file 5. 0.OUTCAR: output file that contains detailed information about the progress of a calculation after the first geometry optimization has been run with the precision variable set to PREC=Low in the INCAR file 6. rlx1.out: file with diagnostic information about the execution of the first geometry optimization with precision variable set to PREC=Low in the INCAR file 7. POSCAR: input file that defines the atomic structure of a system after the first geometry optimization has been run at low precision. This represents the input for the second geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 8. CONTCAR: output file that provides the atomic positions and cell parameters after the second geometry optimization has been run with the precision variable set to PREC=Normal in the INCAR file 9. OUTCAR: output file that contains detailed information about the progress of a calculation after the second geometry optimization has been run with the precision variable set to PREC=Normal in the INCAR file 10. rlx2.out: file with diagnostic information about the execution of the second geometry optimization with precision variable set to PREC=Normal in the INCAR file 11. vaspout.h5: hierarchical HDF5 file containing the inputs and outputs of a VASP calculation. To analyze the data in this file we recommend using py4vasp. This file is only produced if the VASP version used is compiled with HDF5 support 12. vasprun.xml: contains similar information to OUTCAR, but in an xml format. 13. CHGCAR: contains the charge density data of a system. This data is crucial for analyzing electronic structures, calculating electrostatic potential, and studying the distribution of charge in a crystal or molecular system FILES contained in each subdirectory with name "case-N" where N ranges between 1 and 10 and between 81 and 100, extremes included: 1. INCAR: input file that contains various parameters and settings for controlling the behavior of the electronic structure calculations 2. KPOINTS: input file that specifies the Bloch vectors (k points) used to sample the Brillouin zone 3. {ID}.POSCAR: input file that defines the atomic structure of a system at the beginning of ID execution of geometry optimization with PREC=LOW 4. {ID}.CONTCAR: output file that provides the atomic positions and cell parameters at the end of ID execution of geometry optimization with PREC=LOW in the INCAR file 5. {ID}.OUTCAR: output file that contains detailed information about the progress of a calculation after the ID execution of geometry optimization that has been run with the precision variable set to PREC=Low in the INCAR file 6. rlx1.{ID}.out: file with diagnostic information about the execution of the ID execution of the geometry optimization with precision variable set to PREC=Low in the INCAR file 7. N{ID}.POSCAR: input file that defines the atomic structure of a system after the geometry optimization run at low precision. This represents the input for the ID execution of the second geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 8. N{ID}.CONTCAR: output file that provides the atomic positions and cell parameters after the ID execution of the geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 9. N{ID}.OUTCAR: output file that contains detailed information about the progress of a calculation after the ID execution of the geometry optimization run with the precision variable set to PREC=Normal in the INCAR file 10. rlx2.{ID}.out: file with diagnostic information about the ID execution of geometry optimization with precision variable set to PREC=Normal in the INCAR file 11. vaspout.h5: hierarchical HDF5 file containing the inputs and outputs of a VASP calculation. To analyze the data in this file we recommend using py4vasp. This file is only produced if the VASP version used is compiled with HDF5 support 12. vasprun.xml: contains similar information to OUTCAR, but in an xml format. 13. CHGCAR: contains the charge density data of a system. This data is crucial for analyzing electronic structures, calculating electrostatic potential, and studying the distribution of charge in a crystal or molecular system This research is sponsored by the Artificial Intelligence Initiative as part of the Laboratory Directed Research and Development (LDRD) Program of Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the US Department of Energy under contract DE-AC05-00OR22725. This work used resources of the Oak Ridge Leadership Computing Facility, which is supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC05-00OR22725, under Directorate Discretionary awards MAT025 (Materials Science) and LRN026 (Machine Learning), and INCITE award MAT201. This work also used resources of the National Energy Research Scientific Computing Center, which is supported by the Office of Science of the U.S. Department of Energy under Contract No. DE-AC02-05CH11231, under award ERCAP0025216. REFERENCES (1) Kresse, G. & Hafner, J. Ab initio molecular dynamics for liquid metals. Phys. review B 47, 558 (1993). (2) Kresse, G. & Hafner, J. Ab initio molecular-dynamics simulation of the liquid-metal–amorphous-semiconductor transition in germanium. Phys. Rev. B 49, 14251 (1994) (3) Kresse, G. & Furthmüller, J. Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set. Comput. materials science 6, 15–50 (1996) (4) Kresse, G. & Furthmüller, J. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set. Phys. review B 54, 11169 (1996) (5) Kresse, G. & Joubert, D. From ultrasoft pseudopotentials to the projector augmented-wave method. Phys. review b 59, 1758 (1999)

36 MATERIALS SCIENCE↗
DOE OSTI2021

Joint Bayesian Inference for Near-Surface Explosion Yield and Height-of-Burst

Forensic capabilities to understand chemical and nuclear explosions are greatly aided by an accurate estimate of explosive yield with uncertainty. The relationship between explosive size and geophysical observations of seismic, acoustic, and optical waves can be exploited to provide an estimate of yield. Any near-surface yield estimate is complicated by the surface interaction, so an estimate for the explosion height-of-burst is necessarily included in the relationship. Additionally, the relationship dictates a trade-off between estimates of yield and height-of-burst. Fortunately, the surface interaction for each type of observation is different, which breaks the trade-off, and the inclusion of height-of-burst with multiple data types improves yield estimation. We define simple parametric forward models to relate seismoäcoustoöptic observations from a data set of known explosive yields and height-of-bursts. The parameters of the models and a prediction for the yield and height-of-burst of a new event can then be estimated given new observations via Bayesian inference. We report posterior distribution estimates of the parametric models using a Markov chain Monte Carlo sampling technique. These models are then used to predict the yield and height-of-burst of SUGAR, a historical near-surface nuclear explosion, using its reported historical observations. The reported yield of 1.2 ktonne Trinitrotoluene (TNT)-equivalent (Department of Energy, 2015) is within the estimated posterior. Yield uncertainty can be estimated from the spread of the posterior, which is between 0.9 and 2.1 ktonne TNT-equivalent. The posterior for height-of-burst has a wider range between 10 m below and 8 m above ground that includes the true height-of-burst of 1 m.

58 GEOSCIENCES↗
DOE OSTI2023

On the Scaling and Growth Limit of Fluvial Dunes

Abstract Bedforms emerge in a variety of shapes and sizes when a granular erodible surface is subject to a strong enough shear flow, as observed in topographic data from submarine canyons, rivers, deserts, and planetary bodies. The two salient features of bedforms are the ability to collectively transport particles, and to generate form drag thus increasing flow resistance. These two mechanisms are in competition and contribute to force bedforms of increasing size migrating more slowly. In a dedicated large‐scale open channel flow facility, hierarchies of fluvial bedforms were generated and measured in equilibrium conditions. The corresponding scale‐dependent migration velocity and mass flux contributions were quantified in the wave number and frequency domains. Experimental results are paired with a validated set of theoretical models to demonstrate that ripples or dunes reach an equilibrium state when drag partitioning ensures high enough frictional drag to sustain the bedload transport of sediment, and low enough form drag to enable the migration of the largest bedform size. This mechanism is inferred to constrain the growth of bedforms when sediment supply is not the limiting factor.

58 GEOSCIENCES↗
DOE OSTI2026

Why Firn Quakes

Snow dampens sounds, but anecdotal reports concisely describe audible propagating collapse events—firnquakes—in Antarctic and Arctic snowfields. We propose combining granular and continuum mechanics to form a testable theory for conditioning, triggering, and propagation of firnquakes consistent with scarce data. A central condition for collapse events is unconsolidated firn at depth. As firn grains compact, stresses are transmitted along force chains which carry the overburden and transition into a continuous medium by pressure sintering. This granular legacy creates solid-like supports of denser layers that keep the material below unconsolidated. Dynamic amplification triggers local brittle failure of the supports, which induces a cascade of collapse propagation. Using bulk density from ice cores as proxy for stiffness, we find the flexural wave speed by collapsing supports matches the recorded firnquake velocities on the order of 100 m/s. Our theory is to be tested in firn sheets and other compacting granular materials.

Voigtländer, A. [Lawrence Berkeley National Labora↗
DOE OSTI2022

Characterisations of the HinOTORI telescope with a three-color imager at Ali Observatory in Western Tibet

HinOTORI is a new telescope supported by an international collaboration project between China and Japan. It is a 50 centimeter telescope equipped with simultaneous three-color imagers (u',R C , and I C bands). It is located at Ali Observatory at an altitude of 5100m. Thanks to the high altitude and extreme dryness, Ali site is one of the most suitable sites for optical astrometry. HinOTORI telescope aims at detecting optical transients such as the counterparts of gravitational wave (GW) sources, supernovae, gamma-ray bursts (GRB) and so on. This paper describes the site information, design of simultaneous three-color optical layout, system instruments and whole control system. We also report some telescope characterisations for three bands (u'/R C /I C ) respectively, such as Hartmann constant (0.49"/0.56"/0.60"), best focus position (3.922/3.920/3.903 mm), PSF FWHM size (3.755/3.328/3.167pixels), total transmittance and limiting magnitude (15.69/17.57/17.05mag, 10 σ 30 seconds exposure time). With different airmass observation data, the atmospheric extinction coefficients of three bands (0.366/0.061/0.026) were also derived.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Discovery of a Candidate Binary Supermassive Black Hole in a Periodic Quasar from Circumbinary Accretion Variability

Binary supermassive black holes (BSBHs) are expected to be a generic byproduct from hierarchical galaxy formation. The final coalescence of BSBHs is thought to be the loudest gravitational wave (GW) siren, yet no confirmed BSBH is known in the GW-dominated regime. While periodic quasars have been proposed as BSBH candidates, the physical origin of the periodicity has been largely uncertain. Here we report discovery of a periodicity (P=1607±7 days) at 99.95% significance (with a global p-value of ~10 –3 accounting for the look elsewhere effect) in the optical light curves of a redshift 1.53 quasar, SDSS J025214.67–002813.7. Combining archival Sloan Digital Sky Survey data with new, sensitive imaging from the Dark Energy Survey, the total ~20-yr time baseline spans ~4.6 cycles of the observed 4.4-yr (restframe 1.7-yr) periodicity. The light curves are best fit by a bursty model predicted by hydrodynamic simulations of circumbinary accretion disks. The periodicity is likely caused by accretion rate modulation by a milli-parsec BSBH emitting GWs, dynamically coupled to the circumbinary accretion disk. A bursty hydrodynamic variability model is statistically preferred over a smooth, sinusoidal model expected from relativistic Doppler boost, a kinematic effect proposed for PG1302–102. Furthermore, the frequency dependence of the variability amplitudes disfavors Doppler boost, lending independent support to the circumbinary accretion variability hypothesis. Given our detection rate of one BSBH candidate from circumbinary accretion variability out of 625 quasars, it suggests that future large, sensitive synoptic surveys such as the Vera C. Rubin Observatory Legacy Survey of Space and Time may be able to detect hundreds to thousands of candidate BSBHs from circumbinary accretion with direct implications for Laser Interferometer Space Antenna.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Retrieval of full angular- and energy-dependent complex transition dipoles in the molecular frame from laser-induced high-order harmonic signals with aligned molecules

High-order harmonic signals generated in molecules are the consequence of coherent summation of complex laser-induced transition dipoles $\textit{d}(θ, ω)$ with each fixed-in-space molecule; here $\theta$ is the angle of the molecular axis with respect to the laser polarization axis and $\omega$ is the harmonic energy. In the so-called rotational coherent spectroscopy, it is proposed to extract the fixed-in-space $\textit{d}(θ, ω)$ in the molecular frame by measuring harmonics generated by a probing laser from the rotational molecular wave packets that have been prepared by a prior pump laser. By varying the time delay between the two lasers, methods have been utilized to extract the $\theta$ dependence of both the amplitude and phase of each individual harmonic, but the relative phase between harmonics cannot be retrieved. Here we report that this limitation can be removed. It requires the additional measurement of harmonic spectra versus the pump-probe angles at one fixed time delay. The two-dimensional input harmonic data (time-delay and pump-probe angle) are then used to retrieve the full complex transition dipole $\textit{d}(θ, ω)$ using a retrieval method based on machine learning algorithms. Finally, we demonstrate this method on N 2 and CO 2 molecules.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

Seismic H2: Version 1.0

Seismic-H2 is an integrated software package for geological hydrogen reservoir simulation, optimization, and leakage monitoring. The package includes multiple components: (1) code used for modeling seismic wave propagation in 3D heterogeneous elastic media based on finite-difference method to support detection of geological hydrogen storage reservoir leakage; (2) 3D reservoir simulations of leaks from an underground reservoir and 3D simulations of saline aquifers and depleted gas reservoirs; (3) seismic monitoring costs of passive and active seismic monitoring required for UHS; (4) rock physics calculations and interpolations for converting the reservoir simulations from part (2) into the elastic media models in part (1); (5) pre-processing seismic data; and lastly (6), a GUI interface that combines these different components.

Creasy, Neala↗