Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “system strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Crossover between strongly coupled and weakly coupled exciton superfluids

Following a crossover Superfluidity in fermionic systems occurs through the pairing of fermions into bosons, which can undergo condensation. Depending on the strength of the interactions between fermions, the pairs range from large and overlapping to tightly bound. The crossover between these two limits has been explored in ultracold Fermi gases. Liu et al . observed the crossover in an electronic system consisting of two layers of graphene separated by an insulating barrier and placed in a magnetic field. In this two-dimensional system, the pairs were excitons formed from an electron in one layer and a hole in the other. The researchers used magnetic field and layer separation to tune the interactions and detected the signatures of superfluidity through transport measurements. —JS

Science & Technology - Other Topics↗

Microstructure and fracture properties of open-cell porous Ti-6Al-4V with high porosity fabricated by electron beam melting

Highlights: • The Ti-6Al-4V foams with 80% high porosity are prepared by electron beam melting. • The ligament width appears to play the major role for mechanical properties. • The work of fracture is a linear function of ligament width and roughness/width ratio. - Abstract: The open-cell porous Ti-6Al-4V structure with high porosity, intended to be applied as replacement for human cancellous bone, were fabricated by electron beam melting (EBM). Computer aided design (CAD) was applied to design porous structures using the same unit cell with different unit cell sizes from 2.5 to 4 mm, different ligament widths from 600 to 900 μm, and different pore sizes from 1200 to 1800 μm, in order to achieve high porosity of 80% in avoiding the stress shielding effect. In comparison with the CAD designs and the EBM samples, there were minor discrepancies in terms of pore size and ligament width, mainly a result of melting pool. The measured data on the Young's modulus and yield strength of the EBM porous samples can be predicted by the Gibson and Ashby model. All samples with high porosity were found to match well with cancellous bone, with Young's modulus of 2 GPa and yield stress of 31 MPa, effective to diminish the risk of stress shielding effect. For porous EBM sample with high 80% porosity, the work of fracture can increase from 15.9 to 47.6 kJ/m{sup 2} with increasing ligament width from 600 to 900 μm.

36 MATERIALS SCIENCE↗

Probabilities of delayed processes for nuclei involved in the r-process

Delayed fission, along with induced and spontaneous fission, is responsible for the suppression of the production of superheavy elements both during the r-process and after its completion. Beta-decay strength functions are required for calculating delayed fission. In the present study, respective strength functions are calculated by relying on the theory of finite Fermi systems and by predominantly employing nuclear masses and fission barriers predicted by a generalized Thomas-Fermi model. The probabilities for delayed fission and for the emission of delayed neutrons are calculated for a number of isotopes. On the basis of calculations performed in order to determine the probabilities for delayed processes, it is shown that some of the delayed-fission probabilities calculated thus far were substantially overestimated. The application of these new results to calculating the r-process may change substantially both the r-process path and the yields of superheavy nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

UNLOQ: UNderstanding coherence in Light-matter interfaces for Quantum Science (Final Technical Report)

The general goal of this project is to prepare next-generation quantum systems for novel quantum information science applications. Decades of research on quantum optics have provided revolutionary systems for manipulating atomic and photonic quantum coherence in transformative ways. Our hypothesis is that the next-generation quantum systems will come from nano-molecular quantum optics. Specifically, we are interested in coupling the electronic states of molecules or nanoparticles to the quantized radiation field inside an optical cavity to create a set of new photon-matter hybrid excitations, called polaritons. As opposed to atoms, the vibrational modes of molecules and nanoparticles provide new degrees of freedom to mediate the quantum transduction between electronic and photonic states, offering new ways to tune and ultimately control the quantum coherence of the integrated system. In this project we are interested in designing, fabricating, and characterizing the polaritons that arise from coupling CdSe nanoplatelets (NPLs) to a Fabry-Pérot optical cavity. Specific attention was paid to parameters of the system (cavity mode volume, quality factor, etc.) that would maximize the collective coupling strength. Through a combined theoretical and experimental approach, we were able to make important contributions to understanding NPL exciton-polariton photophysics including how to use cavity loss as a tunable parameter in order to manipulate the populations of the upper and lower polariton states. Finally, using state-of-the-art theoretical methods, we were able to show how the collective coupling of many molecular excitons in a cavity can protect polariton coherence from vibrationally-induced decoherence. In particular, for NPL-cavity polaritonic systems, the quantum coherence can be extended by over an order of magnitude at room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of duplex ageing on secondary α precipitates and mechanical properties of the near β-Ti alloy Ti-55531

Highlights: • High strength β-Ti alloys are widely used for their excellent properties. • To reach an excellent combination of strength and ductility, it is attractive to explore the right heat treatment system. • While compared to the conventional single-step ageing process, duplex ageing could change the development and refinement of secondary α precipitations in near/metastable β-Ti alloys resulting varying in performance. • Therefore it is of scientific significance and engineering value to understand the influence of duplex ageing on the formation of secondary α precipitates and mechanical properties for this type of alloy. - Abstract: This paper presents the results of studies on the microstructure and mechanical properties of a near β-Ti alloy processed with different ageing approaches. Influences of intragranular ultrafine α precipitates and grain boundary α layer on mechanical properties in Ti-55531 alloy were analyzed. The results indicate that the precipitation microstructure of the duplex aged alloy exhibits a uniform size and acicular α precipitated orientation shows an angle of approximately 60°. While the morphology of secondary α precipitates in single-step aged samples appear the irregular distribution and heterogeneous size. With the final ageing time increasing, the morphology of intragranular α precipitates and grain boundary α phase brings out a distinct coarsening. The single-step aged alloy can yield a better combination of the ultimate tensile strength (1265 MPa) and ductility (9%). However, the ultimate tensile strength of the duplex aged alloy even reaches 1368 MPa but it breaks at the stage of elastic deformation. The fracture mode of Ti-55531 alloy changes from predominantly dimple fracture in single-step aged samples to predominantly faceted and cleavage type fracture in duplex aged samples causing by the differences of intragranular α precipitates and the interface between grain boundary α layer and intragranular microstructure.

36 MATERIALS SCIENCE↗

Design and testing of high-performance mini-channel graphite heat exchangers in thermoelectric energy recovery systems

Recent national energy usage studies by Lawrence Livermore National Laboratory in 2015 [1] show that there is approximately 59 Quads (1015 Btu’s) of waste thermal energy throughout various industrial, residential, power generation, and transportation sectors of the U.S. economy. Thermoelectric energy recovery is one important technology for recovering this waste thermal energy in high-temperature industrial, transportation and military energy systems. Thermoelectric generator (TEG) systems in these applications require high performance hot-side and cold-side heat exchangers to provide the critical temperature differential and transfer the required thermal energy. High performance hot-side heat exchangers in these systems are often metal-based due to requirements for high-temperature operation, strength at temperature, corrosion resistance, and chemical stability. However, the generally selected metal-based hot-side heat exchangers (i.e., Inconels, Stainless Steels) suffer from low thermal conductivity, high thermal expansion, and high density, which degrades their thermal performance, leads to high thermal-expansion-driven stresses, and creates relatively high mass/high volume (i.e., low power density) TEG systems that are then difficult to fabricate and integrate into viable energy recovery systems. This paper describes the design and testing of a new, high-temperature minichannel graphite heat exchanger designed for operation up to 500C that is a critical element of a high-power-density TEG power system for aircraft energy recovery. This high-performance graphite heat exchanger represents a new state-of-the-art standard in high-temperature heat exchangers for TEG systems, which provides higher thermal transport, less thermal expansion at operation, lower system level stresses on TE components, and a lighter weight TEG system. This new heat exchanger creates a new design paradigm in TEG system design for terrestrial energy recovery and potential NASA technology infusion into terrestrial energy system applications. This paper will present and discuss the key heat transfer, pressure drop, pumping power analyses and design tradeoffs that created this unique design. Heat transfer and pressure drop modeling was performed with both empirical models based on known heat transfer and friction factor correlations and COMSOL thermal/fluid dynamic modeling of the graphite heat exchanger structure. We will also discuss resulting thermal transport and heat fluxes predicted at the TEG interface level. Heat exchanger performance testing was performed under simulated operating conditions and correlation with test data at the anticipated operating temperature conditions will be presented and discussed.

Shevade, Abhijit↗

Shock Prevention

The electrician pictured is installing a General Electric Ground Fault Interrupter (GFI), a device which provides protection against electrical shock in the home or in industrial facilities. Shocks due to defective wiring in home appliances or other electrical equipment can cause severe burns, even death. As a result, the National Electrical Code now requires GFIs in all new homes constructed. This particular type of GFI employs a sensing element which derives from technology acquired in space projects by SCI Systems, Inc., Huntsville, Alabama, producer of sensors for GE and other manufacturers of GFI equipment. The sensor is based on the company's experience in developing miniaturized circuitry for space telemetry and other spacecraft electrical systems; this experience enabled SCI to package interruptor circuitry in the extremely limited space available and to produce sensory devices at practicable cost. The tiny sensor measures the strength of the electrical current and detects current differentials that indicate a fault in the functioning of an electrical system. The sensing element then triggers a signal to a disconnect mechanism in the GFI, which cuts off the current in the faulty circuit.

Source record↗

Theory of finite disturbances in a centrifugal compression system with a vaneless radial diffuser

A previous small perturbation analysis of circumferential waves in circumferential compression systems, assuming inviscid flow, is shown to be consistent with observations that narrow diffusers are more stable than wide ones, when boundary layer displacement effect is included. The Moore-Greitzer analysis for finite strength transients containing both surge and rotating stall in axial machines is adapted for a centrifugal compression system. Under certain assumptions, and except for a new second order swirl, the diffuser velocity field, including resonant singularities, can be carried over from the previous inviscid linear analysis. Nonlinear transient equations are derived and applied in a simple example to show that throttling through a resonant value of flow coefficient must occur in a sudden surge-like drop, accompanied by a transient rotating wave. This inner solution is superseded by an outer surge response on a longer time scale. Surge may occur purely as result of circumferential wave resonance. Numerical results are shown for various parametric choices relating to throttle schedule and the characteristic slope. A number of circumferential modes considered simultaneously is briefly discussed.

Moore, F. K.↗

SLR2000: a microlaser-based single photoelectron satellite laser ranging system

SLR2000 is an autonomous and eyesafe satellite laser ranging (SLR) station with an expected single shot range precision of about one centimeter and a normal point (time-averaged) precision better than 3 mm. The system wil provide continuous 24 hour tracking coverage for a constellation of over twenty artificial satellites. Replication costs are expected to be roughly an order of magnitude less than current operational systems, and the system will be about 75% less expensive to operate and maintain relative to manned systems. Computer simulations have predicted a daylight tracking capability to GPS and lower satellites with telescope apertures of 40 cm and have demonstrated the ability of our current autotracking algorithm to extract mean signal strengths below .001 photoelectrons per pulse from daytime background noise. The dominant cost driver in present SLR systems is the onsite and central infrastructure manpower required to operate the system, to service and maintain the complex subsystems, and to ensure that the transmitted laser beam is not a hazard to onsite personnel or to overflying aircraft. To keep development, fabrication, and maintenance costs at a minimum, we adopted the following design philosophies: (1) use off the shelf commercial components wherever possible; this allows rapid component replacement and "outsourcing" of engineering support; (2) use smaller telescopes (less than 50 cm) since this constrains the cost, size, and weight of the telescope and tracking mount; and (3) for low maintenance and failsafe reliability, choose simple versus complex technical approaches and, where possible, use passive techniques and components rather than active ones. Adherence to these philosophies has led to the SLR2000 design described here.

Degnan, John J.↗

Further Investigation of Surface Velocity Measurements for Material Characterization in Laser Shockwave Experiments

Further investigation of surface velocity measurements for material characterization in laser shockwave experiments James A. Smith, Jeffrey M. Lacy, Clark L. Scott, Bradley C. Benefiel Idaho National Laboratory, Idaho Falls ID Daniel Levesque, Jean-Pierre Monchalin and Martin Lord, National Research Council Canada, Boucherville, QC, Canada ---As part of the US High Performance Research Reactor program, a laser shockwave system is being developed by the Idaho National Laboratory (INL) to characterize interface strength in innovative plate fuel for research reactors around the world. The INL has been working with National Research Council Canada (NRC) on this project for the last five years. One of the concerns is the difficulty of calibrating and standardizing the laser shock technique. The generation of a stress wave by the laser impinging on the plate surface is dependent on the surface preparation, temporal and spatial power distribution of the laser spot, and material properties of the plate. Thus the resulting back surface velocity used to measure the time-varying stress field within the plate is difficult to reproduce across different measurement systems. ---A recent analytical study and testing support the use of the Hugoniot Elastic Limit (HEL) in materials as a robust and simple benchmark to compare stresses generated by different laser shock systems [1]. Using a non-contact laser velocimeter based on a solid Fabry-Perot etalon, the systems at NRC and INL showed that the velocity reached at the HEL is consistent, independent of the laser power used. In this work, the laser velocimeter of the NRC system is tested against a fast rotating wheel to verify accuracy and determine best operating conditions. A round robin test between the two laser shock systems on plates of different Al alloys is presented that shows the correct classification of the Al alloys based on the HEL as well as determining the bias between the systems. Also the effects of some setup parameters on other characteristics of the surface velocity and corresponding stress wave are discussed. 1. J.A. Smith, J.M. Lacy, D. Levesque, J.-P. Monchalin and M. Lord, "Use of the Hugoniot elastic limit in laser shockwave experiments to relate velocity measurements, 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation, AIP Conf. Proc. 1706, pp. 080005-1-080005-10, 2016.

36 MATERIALS SCIENCE↗

Geometry Systems for Lattice-Based Reconfigurable Space Structures

We describe analytical methods for the design of the discrete elements of ultralight lattice structures. This modular, building block strategy allows for relatively simple element manufacturing, as well as relatively simple robotic assembly of low mass density structures on orbit, with potential for disassembly and reassembly into highly varying and large structures. This method also results in a structure that is easily navigable by relatively small mobile robots. The geometry of the cell can allow for high packing efficiency to minimize wasted payload volume while maximizing structural performance and constructability. We describe the effect of geometry choices on the final system mechanical properties and automated robotic constructability of a final system. Geometric properties considered include number of attachments per voxel, number of attachments per coefficient of volume, and effects of vertex, edge, and face connectivity of the unit cell. Mechanical properties considered include strength scaling, modulus scaling, and packing efficiency of the lattice. Automated constructibility metrics include volume allowance for an end-effector, strut clearance angle for an end-effector, and packing efficiency. These metrics were applied to six lattice unit cell geometries: cube, cuboctahedron, octahedron, octet, rhombic dodecahedron, and truncated octahedron. A case study is presented to determine the most suitable lattice system for a specific set of strength and modulus scaling requirements while optimizing for ease of robotic assembly.

lattice geometry↗

Geometry Systems for Lattice-Based Reconfigurable Space Structures

We describe analytic methods for the design of the discrete elements of ultralight lattice structures. This modular building block strategy allows for relatively simple element manufacturing as well as relatively simple robotic assembly of low mass-density structures on orbit, with potential for disassembly and reassembly into highly varying and large structures. This method also results in a structure that is easily navigable by relatively small, mobile robots. The geometry of the cell can allow for high packing efficiency to minimize wasted payload volume while maximizing structural performance and constructability. We describe the effect of geometry choices on the mechanical properties and automated robotic constructability of a final system. Geometric properties considered include number of attachments per voxel, number of attachments per coefficient of volume, and effects of vertex, edge, and face connectivity of the unit cell. Mechanical properties considered include strength scaling, modulus scaling, and packing efficiency of the lattice. Automated constructibility metrics include volume allowance for an end-effector, strut clearance angle for an end-effector, and packing efficiency. These metrics were applied to six lattice unit cell geometries: cube, cuboctahedron, octahedron, octet, rhombic dodecahedron, and truncated octahedron. A case study is presented to determine the most suitable lattice system for a specific set of strength and modulus scaling requirements while optimizing for ease of robotic assembly.

digital materials↗

Neural Mechanisms to the Space Environment

Highly conserved neural systems have evolved to sense the inertial forces due to head translation and head tilt relative to gravitational vertical. These structures consist of ciliated mechanosensitive receptor cells inserted into a neuroepithelium surmounted by biomineral grains of calcium carbonate (CaCO3) called oto- (vertebrates) or stato-conia (invertebrates). Detection of these forces by receptor cells relies on the CaCO3 mass being weighted in Earths 1G. A change in gravity or orientation with respect to gravity has a profound effect on how an organism interacts with its environment, and it is evident that the nervous system responds to the new gravity state. This response might involve the peripheral receptors, the CaCO3 mass, the brain or any combination of these mechanisms based on the intensity and duration of the gravity change. Here, we examine the arguments supporting the different mechanisms of adaptation to the space environment. First, a pre- or post-synaptic alteration in the strength of synaptic transmission between the receptor cell and nerve afferent can adjust the system output. The number of synaptic ribbons in certain type II hair cells in rodent is labile, increasing following exposure to microgravity. An increase in number of synaptic ribbons in toadfish otolith hair cells following exposure to microgravity could potentially explain the observed afferent hypersensitivity to acceleration postflight. The physiological findings in the isolated statocyst in snails are in line with the vertebrate data, and conform to the proposition that G exposure leads to changes in gravireceptor function. At the same time this similarity in neural response to G exposure between the vertebrates and invertebrates is intriguing: the increased neural sensitivity in the vertebrate was detected in the nerve afferents, one synapse away from the receptor cell, whereas the increased neural sensitivity observed in the snail was detected directly at the receptor level. Second, the CaCO3 mass provides mechanical loading of receptor cell cilia, and their density alters sensitivity. A widely considered mechanism by which the animal responds to a chronic change in amplitude of gravity is a change in weight-lending CaCO3 mass. In G, it is argued, the organism counters the loss of gravity by increasing CaCO3 production, thereby increasing its mass, as a means to increase system gain. In hypergravity, the converse is argued. Earlier evidence in mollusks and recent results in mice suggest a remodeling might occur, especially after long-term space exposure. Lastly, we have to distinguish at least two kinds of neural feedbacks. One is connected with local mechanisms of self-regulation and specific for initial period of organ development when the neural connections are still absent. And the other feedback is related to neural self-regulation and specific for later stages of the organ development, and includes an efferent vestibular feedback. Complexity of the problem is enhanced by incompleteness of experiments, and consequently the experimental results have not led to a clear interpretation despite the numerous studies.

Boyle, Richard D.↗

Beam-water Interaction System for PFAS Treatment

Per- and polyfluoroalkyl substances (PFAS) are persistent environmental contaminants that resist conventional water treatment due to the strength of their carbon fluorine bonds. Electron-beam irradiation has shown potential for PFAS degradation; however, its effectiveness is limited by shallow energy penetration, restricting treatment to the upper region of the water surface. This project addresses this limitation through the design of a compact mixing chamber and recirculation system to enhance surface renewal and improve treatment efficiency. The system, constrained to approximately 10 cm 20 cm 20 cm, was developed using computer-aided design, computational fluid dynamics (CFD), and MATLAB-based hydraulic analysis to evaluate flow behavior, head loss, and pump compatibility. A perforated-baffle geometry and controlled flow range of 1 3 GPM were implemented to promote uniform mixing while maintaining a stable free surface for electron-beam exposure. Modeling results indicate improved flow distribution and reduced dead zones, supporting more consistent interaction between contaminated water and the beam. The final design enhances hydrodynamic performance within system constraints, contributing to scalable electron-beam water treatment technologies for improved PFAS degradation.

Ramos, Gerardo [Northern Illinois U.]↗

Inference System Integration Via Logic Morphisms

This is a final report on the accomplishments during the period of the NASA grant. The work on inference servers accomplished the integration of the SLANG logic (Specware's default specification logic) with a number of inference servers in order to make their complementary strengths available. These inverence servers are (1) SNARK. (2) Gandalf, Setheo, and Spass, (3) the Prototype Verification System (PVS) from SRI. (4) HOL98. We designed and implemented MetaSlang, an ML-like language, which we are using to specify and implement all our logic morphisms.

Bjorner, Nikolaj S.↗

Role of baryon number conservation in measurements of fluctuations

Here, I discuss the role and impact of net-baryon number conservation in measurements of net-proton fluctuations in heavy-ion collisions. I show that the magnitude of the fluctuations is entirely determined by the strength of two particle correlations. At LHC and top RHIC energy, this implies the fluctuations are proportional to the integral of the balance function (BF), B pp¯ of protons and antiprotons, while in the context of the RHIC beam energy scan (BES), one must also account for correlations of stopped protons. The integral of B pp¯ measured in a 4π detector depends on the relative cross sections of processes yielding pp¯ and those balancing the proton baryon number via the production of other antibaryons. The accepted integral of B pp¯ further depends on the shape and width of the BF relative to the width of the acceptance. The magnitude of the measured second-order cumulant of net-proton fluctuations thus has much less to do with QCD susceptibilities than with the creation/transport of baryons and antibaryons in heavy-ion collisions, and most particularly the impact of radial flow on the width of the BF. I thus advocate that net-proton fluctuations should be studied by means of differential BF measurements rather than with integral correlators. I also derive an expression of net-baryon fluctuations in terms of integrals of balance functions of identified baryon pairs and argue that measurements of such balance functions would enable a better understanding of the collision system expansion dynamics, the hadronization chemistry, and an experimental assessment of the strength of net-baryon fluctuations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Global Ocean Mass Change Derived From Atmospheric Reanalyses

Barystatic sea level change is a significant climate variable and a gauge for water exchanges between land, atmosphere, and ocean, with consequential relevance to stakeholders. The monitoring and attribution of globally averaged sea level variations represents substantial challenges to the climate community. Atmospheric reanalyses provide a level of monitoring for elements of the climate system that are in communication with the ocean, including the atmosphere, terrestrial land, and the surfaces of glaciated land. Global atmospheric reanalyses comprise model output that is statistically adjusted to available observations. Potentially, reanalyses offer a climatic context to observed changes in water mass distribution. Improvement in the representation of the water cycle and in water mass conservation have been stated goals of reanalysis projects. Here, we assess the capability of atmospheric reanalyses to represent variations in the global water budget from the perspective of ocean mass balance. The purpose of this work is to provide a detailed evaluation of current atmospheric reanalyses and their ability to reproduce spatial and temporal variations in atmospheric and terrestrial water storage. A second goal is to identify and characterize recent apparent trends in the water balance. We examine the ERA5, MERRA-2, and JRA-3Q reanalyses with a focus on the radio-occultation observing period from 2007 to the present. For terrestrial water storage we also compare with ERA5-Land, a surface reanalysis. The primary validation is from the NASA/DLR Gravity Recovery and Climate Experiment (GRACE) and its follow-on, GRACE-FO. The Atmospheric Infrared Sounder (AIRS) onboard NASA's Aqua satellite is also used for evaluation of the atmospheric moisture budget. Comparisons reveal strengths and weaknesses in the reanalyses of each component of the climate system. Reanalyses agree closely on atmospheric moisture storage trends, although mean values differ. Reanalyses show significant differences in land water storage. They also apply large corrections to the land water budget. Finally, reanalyses have differing abilities in representing the surface mass balance over glaciated land. Using the observed gravimetry record, changes in the underlying glaciated land ice are examined as a residual.

Richard Cullather↗

SU-F-J-143: Initial Assessment of Image Quality of An Integrated MR-Linac System with ACR Phantom

Purpose/Objective(s): To assess the image quality of an integrated MR-Linac system and compare with other MRI systems that are primarily used for diagnostic purposes. Materials/Methods: An ACR MRI quality control (QC) phantom was used to evaluate the image quality of a fully integrated 1.5T MRI-Linac system recently installed at our institution. This system has a new split magnet design which gives the magnetic field strength of 1.5T. All images were acquired with a set of phased-array surface coils which are designed to have minimal attention of radiation beam. The anterior coil rests on a coil holder which keeps the anterior coil’s position consistent for QA purposes. The posterior coil is imbedded in the patient couch. Multiple sets of T1, T2/PD images were acquired using the protocols as prescribed by the ACR on three different dates, ranging 3 months apart. Results: The geometric distortion are within 0.5 mm in the axial scans and within 1mm in the saggital (z-direction) scans. Slice thickness accuracy, image uniformity, ghosting ratio, high contrast detectability are comparable to other 1.5T diagnostic MRI scanners. The low-contrast object detectability are lower comparatively, which is a result of using the body array coil. Additionally, the beam’s-eye-view images (oblique coronal and saggital images) have minimal geometric distortion at all linac gantry angles tested. No observable changes or drift in image quality is found from images acquired 3 month apart. Conclusion: Despite the use of a body array surface coil, the image quality is comparable to that of an 1.5T MRI scanner and is of sufficient quality to pass the ACR MRI accreditation program. The geometric distortion of the MRI system of the integrated MR-Linac is within 1mm for an object size similar to the ACR phantom, sufficient for radiation therapy treatment purpose. The authors received corporate sponsored research grants from Elekta which is the vendor for the MR-Linac evaluated in this study.

60 APPLIED LIFE SCIENCES↗