SEARCH · Engineering Papers

Results for “station”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Space Station pressure wall repair techniques

Space Station components are susceptible to hypervelocity impact damage from orbital debris and meteoroids. An especially vulnerable and critical space station component is the module pressure wall. Even with shielding, sufficiently large impacting particles can create penetrations ranging from pinholes to large jagged holes. This paper describes pressure wall damage repair patches along with procedures and tools for performing the repair. One patch incorporates an aluminum foil protected from the jagged hole edge with a Kevlar or foam pad. An adhesive holds the patch in place. Another patch uses a stiff plate held away from the damaged area by a low durrometer rubber ring which also seals the plate edge. An adhesive will also secure this patch in place. Procedures were developed to prepare the punctured wall surface and apply the patch under weightless and unpressurized conditions. The procedures were tested in a laboratory and in the MSFC Neutral Buoyancy Simulator with models of the patches and tools.

Gibbins, Martin N.↗

NASA NTRS1988

Orbit lifetime characteristics for Space Station

The factors that influence the orbital lifetime characteristics of the NASA Space Station are discussed. These include altitude, attitude, launch date, ballistic coefficient, and the presence of large articulating solar arrays. Examples from previous program systems studies are presented that illustrate how each factor affects Station orbit lifetime. The effect of atmospheric density models on orbit lifetime predictions is addressed along with the uncertainty of these predictions using current trajectory analysis of the Long Duration Exposure Facility spacecraft. Finally, nominal reboost altitude profiles and fuel requirement considerations are presented for implementing a reboost strategy based on planned Shuttle Orbiter rendezvous strategy and contingency considerations.

Deryder, L.↗

NASA NTRS1988

Radiation dose and shielding for the space station

Significant differences in dose prediction for Space Station arise depending on whether or not the magnetic field model is extrapolated into the future. The basis for these calculations is examined in detail, and the importance of the residual atmospheric layer at altitudes below 1000 km, with respect to radiation attenuation, is emphasized. Dosimetry results from Shuttle flights are presented and compared with the computed results. It is recommended that, at this stage, no extrapolation of the magnetic field into the future be included in the calculations. A model adjustment, to replace this arbitrary procedure, is presented. Dose predictions indicate that, at altitudes below 500 km and at low inclination, and with nominal module wall thickness (0.125 in. aluminum), orbit stay times of 90 days in Space Station would result in quarterly radiation doses to the crew, which are well within present limits for both males and females. Countermeasures would be required for stay times of a year or more and the measure of increasing shielding is examined.

Mccormack, Percival D.↗

NASA NTRS1988

Evaluation of chromic acid anodized aluminum foil coated composite tubes for the Space Station truss structure

This paper describes the development and evaluation of chromic acid anodized (CAA) Al foil as a protective and thermal control coating for graphite/epoxy tubes designed for the Space Station truss structure. Special consideration is given to the development of solar-absorptance and thermal-emittance properties required of Al foil, the development of CAA parameters necessary to achieve these optical properties, and the atomic oxygen and UV testing of CAA Al foil. Results showed that 0.003-in CAA Al foil cocured or secondary bonded to graphite/epoxy tubes with thin epoxy film adhesive retains excellent bond strength and provides a superior protective and thermal control coating to the LEO environment. Processes were developed for CAA Al foils long enough to continuously wrap the 23-ft-long diagonal struts of the Space Station truss structure. Specifications are presented for the processes of chromic acid anodizing of Al foil and for the bonding of anodized Al foil to graphite/epoxy tubes.

Dursch, Harry W.↗

NASA NTRS1988

Performance considerations for the astrometric Telescope Facility on the Phase I Space Station

The Astrometric Telescope Facility (ATF) is an optical telescope facility of extreme astrometric precision whose principal scientific purpose is the detection and study of planetary systems about nearby stars. With the recent change in the space station program to two phases, the suitability of initial operations from the phase 1 station need to be evaluated. This paper presents the results of such an evaluation for the Astrometric Telescope Facility.

Nishioka, Kenji↗

NASA NTRS1987

Simulation of an advanced scout attack helicopter for crew station studies

The system complexity and high workload of the next generation of light scout/attack helicopters is being evaluated in the Crew Station Research and Development Program. This program has been established to study the issues of battle captain performance for one-man versus two-man crews when confronted by a hostile environment. The crew station experiments are described along with the facility elements and simulation.

Lypaczewski, P. A.↗

NASA NTRS1988

Nano-g environment on the Orbiter or Space Station

To achieve a nanogravity environment on the Space Shuttle Orbiter or Space Station a floating table is proposed. With precise control of the initial release conditions, float times of many minutes can be expected before touching a wall. The use of small thrusters available on the spacecraft to fly the station around the floating table would allow experiment times of many hours.

Von Bun, Friedrich O.↗

NASA NTRS1988

Integration of Space Station propulsion and fluid systems

The benefits which would be gained by providing commonality and integration of propulsion and fluid systems associated with various elements of the Space Station are discussed and the results of the integrated propulsion system assessment are presented. The O2/H2 propulsion system with and without resistojets, the integration of O2/H2 systems across the Space Station elements, and an approach for handling waste fluids available for resistojet venting are evaluated. It is shown that major benefits can be gained through commonality and integration. Several systems are recommended, including a gaseous O2/H2 propulsion system with resistojets, a Bosch CO2 reduction process, and pumping electrolysis units.

Bicknell, B. A.↗

NASA NTRS1988

NASA Office of Space Sciences and Applications study on Space Station attached payload pointing

A study has been conducted to determine the articulated-pointing requirements of a suite of instruments carried by the NASA Space Station, and define a pointing system architecture accomodating those requirements. It is found that these pointing requirements are sufficiently exacting, and the Space Station's disturbance environment sufficiently severe, to preclude the successful use of a conventional gimbal-pointing system; a gimbaled system incorporating an isolation stage is judged capable of furnishing the requisite levels of pointing performance.

Laskin, R. A.↗

NASA NTRS1988

The dynamics and control of the orbiting spacecraft control laboratory experiment (SCOLE) during station keeping

A mathematical model is developed to predict the dynamics of the proposed orbiting Spacecraft Control Laboratory Experiment during the station keeping phase. The Shuttle as well as the reflector are assumed to be rigid, the mast is flexible and is assumed to undergo elastic displacements very small as compared with its length. The equations of motion are derived using a Newton-Euler formulation. The model includes the effects of gravity, flexibility, and orbital dynamics. The control is assumed to be provided to the system through the Shuttle's three torquers, and through six actuators located by pairs at two points on the mast and at the mass center of the reflector. At each of the locations, an actuator acts parallel to the roll axis while the other one acts parallel to the pitch axis. It is seen that, in the presence of gravity-gradient torques in the system dynamics, the system assumes a new equilibrium position about which the equations must be linearized, primarily due to the offset in the mast attachment point to the reflector. The linear regulator theory is used to derive control laws for the linear model of the SCOLE including the first four flexible modes. Numerical results confirm the robustness of this control strategy for station keeping with maximum control efforts significantly below saturation levels.

Bainum, Peter M.↗

NASA NTRS1988

Technologies for protection of the Space Station power system surfaces in atomic oxygen environment

Technologies for protecting Space Station surfaces from degradation caused by atomic oxygen are discussed, stressing protection of the power system surfaces. The Space Station power system is described and research concerning the solar array surfaces and radiator surfaces is examined. The possibility of coating the solar array sufaces with a sputter deposited thin film of silicon oxide containing small concentrations of polytetrafluoroethylene is presented. Hexamethyldisiloxane coating for these surfaces is also considered. For the radiator surfaces, possible coatings include silver teflon thermal coating and zinc orthotitanate.

Nahra, Henry K.↗

NASA NTRS1988

25-LBF GO2/GH2 space station thruster

Multiple 25-lbf oxygen/gaseous hydrogen thruster assemblies for the Space Station propulsion application were designed and fabricated by Rocketdyne and endurance tested at the NASA/Marshall Space Flight Center. The thrusters incorporate a regeneratively cooled thrust chamber with a nozzle area ratio of 30, a 12-element coaxial injector, an ignition system, and close-coupled propellant valves. The various thruster configurations comprised of mating different injectors and thrust chambers. Over 2 million lbf-sec of impulse was demonstrated at mixture ratios from 3 to 8.4 at vacuum conditions. A thruster was subjected to over 10,000 pulses during which minimum impulse bits of less than 0.5 lb/sec were repeatedly and reliably demonstrated. A total operating time of 25.6 hr was accumulated on the thruster assemblies with one 6.1-hr. continuous firing duration. The thrusters operated between a thrust range of 11.2 and 36.6 lbf. The test results indicate that all major technology issues for long-life gaseous oxygen/gaseous hydrogen thrusters for the Space Station application have been resolved.

Finden, L. E.↗

NASA NTRS1988

Space Station Information Systems

The utility of the Space Station is improved, the ability to manage and integrate its development and operation enhanced, and the cost and risk of developing the software for it is minimized by three major information systems. The Space Station Information System (SSIS) provides for the transparent collection and dissemination of operational information to all users and operators. The Technical and Management Information System (TMIS) provides all the developers with timely and consistent program information and a project management 'window' to assess the project status. The Software Support Environment (SSE) provides automated tools and standards to be used by all software developers. Together, these three systems are vital to the successful execution of the program.

Pittman, Clarence W.↗

NASA NTRS1989

Trash-Disposal Module For Space Station

Report presents basic engineering concepts of trash-disposal module for Space Station. Module conserves valuable cargo volume and reduces both launching and returning weights of Space Shuttle or other spacecraft carrying materials to and from Space Station. Module relatively cheap and simple to operate.

Wissinger, David B.↗

NASA NTRS1989

Predictive Attitude Maintenance For A Space Station

Paper provides mathematical basis for predictive management of angular momenta of control-moment gyroscopes (CMG's) to control attitude of orbiting space station. Numerical results presented for pitch control of proposed power-tower space station. Based on prior orbit history and mathematical model of density of atmosphere, predictions made of requirements on dumping and storage of angular momentum in relation to current loading state of CMG's and to acceptable attitude tolerances.

Hattis, Philip D.↗

NASA NTRS1989

Aiming Instruments On The Space Station

Report discusses capabilities and requirements for aiming scientific instruments carried aboard proposed Space Station. Addresses two issues: whether system envisioned for pointing instruments at celestial targets offers sufficiently low jitter, high accuracy, and high stability to meet scientific requirements; whether it can do so even in presence of many vibrations and other disturbances on Space Station. Salient conclusion of study, recommendation to develop pointing-actuator system including mechanical/fluid base isolator underneath reactionaless gimbal subsystem. This kind of system offers greatest promise of high performance, cost-effectiveness, and modularity for job at hand.

Estus, Jay M.↗

NASA NTRS1987

A hierarchically distributed architecture for fault isolation expert systems on the space station

The Space Station Axiomatic Fault Isolating Expert Systems (SAFTIES) system deals with the hierarchical distribution of control and knowledge among independent expert systems doing fault isolation and scheduling of Space Station subsystems. On its lower level, fault isolation is performed on individual subsystems. These fault isolation expert systems contain knowledge about the performance requirements of their particular subsystem and corrective procedures which may be involved in repsonse to certain performance errors. They can control the functions of equipment in their system and coordinate system task schedules. On a higher level, the Executive contains knowledge of all resources, task schedules for all systems, and the relative priority of all resources and tasks. The executive can override any subsystem task schedule in order to resolve use conflicts or resolve errors that require resources from multiple subsystems. Interprocessor communication is implemented using the SAFTIES Communications Interface (SCI). The SCI is an application layer protocol which supports the SAFTIES distributed multi-level architecture.

Miksell, Steve↗

NASA NTRS1988

Space station electrical power system availability study

ARINC Research Corporation performed a preliminary reliability, and maintainability (RAM) anlaysis of the NASA space station Electric Power Station (EPS). The analysis was performed using the ARINC Research developed UNIRAM RAM assessment methodology and software program. The analysis was performed in two phases: EPS modeling and EPS RAM assessment. The EPS was modeled in four parts: the insolar power generation system, the eclipse power generation system, the power management and distribution system (both ring and radial power distribution control unit (PDCU) architectures), and the power distribution to the inner keel PDCUs. The EPS RAM assessment was conducted in five steps: the use of UNIRAM to perform baseline EPS model analyses and to determine the orbital replacement unit (ORU) criticalities; the determination of EPS sensitivity to on-orbit spared of ORUs and the provision of an indication of which ORUs may need to be spared on-orbit; the determination of EPS sensitivity to changes in ORU reliability; the determination of the expected annual number of ORU failures; and the integration of the power generator system model results with the distribution system model results to assess the full EPS. Conclusions were drawn and recommendations were made.

Turnquist, Scott R.↗