Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivation layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Evaluation of Spaceborne L-band Radiometer Measurements for Terrestrial Freeze/Thaw Retrievals in Canada

The landscape freeze/thaw (FT) state has an important impact on the surface energy balance, carbon fluxes, and hydrologic processes; the timing of spring melt is linked to active layer dynamics in permafrost areas. L-band (1.4 GHz) microwave emission could allow the monitoring of surface state dynamics due to its sensitivity to the pronounced permittivity difference between frozen and thawed soil. The aim of this paper is to evaluate the performance of both Aquarius and Soil Moisture and Ocean Salinity (SMOS) L-band passive microwave measurements using a polarization ratio-based algorithm for landscape FT monitoring. Weekly L-band satellite observations are compared with a large set of reference data at 48 sites across Canada spanning three environments: tundra, boreal forest, and prairies. The reference data include in situ measurements of soil temperature (Tsoil) and air temperature (Tair), and Moderate Resolution Imaging Spectroradiometer (MODIS) land surface temperature (LST) and snow cover area (SCA) products. Results show generally good agreement between Lband FT detection and the surface state estimated from four reference datasets. The best apparent accuracies for all seasons are obtained using Tair as the reference. Aquarius radiometer 2 (incidence angle of 39.6) data gives the best accuracies (90.8), while for SMOS the best results (87.8 of accuracy) are obtained at higher incidence angles (55- 60). The FT algorithm identifies both freeze onset and end with a delay of about one week in tundra and two weeks in forest and prairies, when compared to Tair. The analysis shows a stronger FT signal at tundra sites due to the typically clean transitions between consistently frozen and thawed conditions (and vice versa) and the absence of surface vegetation. Results in the prairies were poorer because of the influence of vegetation growth in summer (which decreases the polarization ratio) and the high frequency of ephemeral thaw events during winter. Freeze onset and end maps created from the same algorithm applied to SMOS and Aquarius measurements characterize similar FT patterns over Canada. This study shows the potential of using L-band spaceborne observations for FT monitoring, but underlines some limitations due to ice crusts in the snowpack, liquid water content in snow cover during the spring freeze to thaw transition, and vegetation growth.

soil freeze/thaw↗

POST-OPERATIONAL TREATMENT OF RESIDUAL NA COOLLANT IN EBR-2 USING CARBONATION

At the end of 2002, the Experimental Breeder Reactor Two (EBR-II) facility became a U.S. Resource Conservation and Recovery Act (RCRA) permitted site, and the RCRA permit1 compelled further treatment of the residual sodium in order to convert it into a less reactive chemical form and remove the by-products from the facility, so that a state of RCRA 'closure' for the facility may be achieved (42 U.S.C. 6901-6992k, 2002). In response to this regulatory driver, and in recognition of project budgetary and safety constraints, it was decided to treat the residual sodium in the EBR-II primary and secondary sodium systems using a process known as 'carbonation.' In early EBR-II post-operation documentation, this process is also called 'passivation.' In the carbonation process (Sherman and Henslee, 2005), the system containing residual sodium is flushed with humidified carbon dioxide (CO{sub 2}). The water vapor in the flush gas reacts with residual sodium to form sodium hydroxide (NaOH), and the CO{sub 2} in the flush gas reacts with the newly formed NaOH to make sodium bicarbonate (NaHCO{sub 3}). Hydrogen gas (H{sub 2}) is produced as a by-product. The chemical reactions occur at the exposed surface of the residual sodium. The NaHCO{sub 3} layer that forms is porous, and humidified carbon dioxide can penetrate the NaHCO{sub 3} layer to continue reacting residual sodium underneath. The rate of reaction is controlled by the thickness of the NaHCO{sub 3} surface layer, the moisture input rate, and the residual sodium exposed surface area. At the end of carbonation, approximately 780 liters of residual sodium in the EBR-II primary tank ({approx}70% of original inventory), and just under 190 liters of residual sodium in the EBR-II secondary sodium system ({approx}50% of original inventory), were converted into NaHCO{sub 3}. No bare surfaces of residual sodium remained after treatment, and all remaining residual sodium deposits are covered by a layer of NaHCO{sub 3}. From a safety standpoint, the inventory of residual sodium in these systems was greatly reduced by using the carbonation process. From a regulatory standpoint, the process was not able to achieve deactivation of all residual sodium, and other more aggressive measures will be needed if the remaining residual sodium must also be deactivated to meet the requirements of the existing environmental permit. This chapter provides a project history and technical summary of the carbonation of EBR-II residual sodium. Options for future treatment are also discussed.

36 MATERIALS SCIENCE↗

New insight into the microstructure and doping of unintentionally n-type microcrystalline silicon carbide

Microcrystalline silicon carbide (μc-SiC:H) deposited by hot wire chemical vapor deposition (HWCVD) and plasma-enhanced chemical vapor deposition (PECVD) provide advantageous opto-electronic properties, making it attractive as a window layer material in silicon thin-film and silicon heterojunction solar cells. However, it is still not clear which electrical transport mechanisms yield dark conductivities up to 10{sup −3} S/cm without the active use of any doping gas and how the transport mechanisms are related to the morphology of μc-SiC:H. To investigate these open questions systematically, we investigated HWCVD and PECVD grown layers that provide a very extensive range of dark conductivity values from 10{sup −12} S/cm to 10{sup −3} S/cm. We found out by secondary ion mass spectrometry measurements that no direct correlation exists between oxygen or nitrogen concentrations and high dark conductivity σ{sub d}, high charge carrier density n, and low activation energy Ea. Higher σ{sub d} seems to rise from lower hydrogen concentrations or/and larger coherent domain sizes L{sub SiC}. On the one hand, the decrease of σ{sub d} with increasing hydrogen concentration might be due to the inactivation of donors by hydrogen passivation that gives rise to decreased n. On the other hand, qualitatively consistent with the Seto model, the lower σ{sub d} and lower n might be caused by smaller L{sub SiC}, since the fraction of depleted grain boundaries with higher Ea increases accordingly.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Excimer laser annealing: A gold process for CZ silicon junction formation

A cold process using an excimer laser for junction formation in silicon has been evaluated as a way to avoid problems associated with thermal diffusion. Conventional thermal diffusion can cause bulk precipitation of SiOx and SiC or fail to completely activate the dopant, leaving a degenerate layer at the surface. Experiments were conducted to determine the feasibility of fabricating high quality p-n junctions using a pulsed excimer laser for junction formation at remelt temperature with ion-implanted surfaces. Solar-cell efficiency exceeding 16 percent was obtained using Czochralski single-crystal silicon without benefit of back surface field or surface passivation. Characterization shows that the formation of uniform, shallow junctions (approximately 0.25 micron) by excimer laser scanning preserves the minority carrier lifetime that leads to high current collection. However, the process is sensitive to initial surface conditions and handling parameters that drive the cost up.

Wong, David C.↗

High absorption photovoltaic material and methods of making the same

A high absorption photovoltaic material and method of making the material for use in a solar cell are disclosed. The photovoltaic material includes a surface modified with a layer of repeating photonic crystal structures. The photonic crystal structures are approximately inverse conically shaped and have a curved sidewall that has an approximately Gaussian shape. The photonic crystal structures generally have a high vertical depth and sidewall angle. The structures also have a gradient refractive index profile and exhibit the parallel-to-interface refraction light trapping effect. An anti-reflective coating is disposed over the photonic crystal structure layer. The photovoltaic material exhibits near unity light absorption over a broad range of visible and near infrared wavelengths and incidence angles, even at reduced thicknesses. The photovoltaic structures are formed via a combined photolithography and reactive-ion etching method at low power with a gas mixture having a high ratio of an etchant component to a passivation component.

Kuang, Ping↗

Junction Quality of SnO 2 -Based Perovskite Solar Cells Investigated by Nanometer-Scale Electrical Potential Profiling

Electron-selective layers (ESLs) and hole-selective layers (HSLs) are critical in high-efficiency organic-inorganic lead halide perovskite (PS) solar cells for charge-carrier transport, separation, and collection. We developed a procedure to assess the quality of the ESL/PS junction by measuring potential distribution on cross-section of SnO 2 -based perovskite solar cells using Kelvin probe force microscopy. Using the potential profiling, we compared three types of cells made of different ESLs but otherwise having identical device structure: cells with PS deposited directly on bare fluorine-doped SnO 2 (FTO)-coated glass; cells with an intrinsic SnO 2 thin layer on the top of FTO as an effective ESL; and cells with the SnO2 ESL and adding a self-assembled monolayer (SAM) of fullerene. The results reveal two major potential drops or electric fields at the ESL/PS and PS/HSL interfaces. The electric-field ratio between the ESL/PS and PS/HSL interfaces increased in devices as follows: FTO < SnO 2 -ESL < SnO 2 +SAM; this sequence explains the improvements of fill factor (FF) and open-circuit voltage ( V oc ). The improvement of FF from the FTO to SnO 2 -ESL cells may result from the reduction in voltage lose at the PS/HSL back interface and the improvement of V oc from the prevention of hole recombination at the ESL/PS front interface. The further improvements with adding a SAM is caused by the defect passivation at the ESL/PS interface, and hence, improvement of the junction quality. Furthermore, these nanoelectrical findings suggest possibilities for improving the device performance by further optimizing the SnO2-based ESL material quality and the ESL/PS interface.

36 MATERIALS SCIENCE↗

The origin of passivity in aluminum-manganese solid solutions

In this work, the effects of manganese on the aqueous corrosion of aluminum-manganese alloys were investigated by experiments and atomistic simulations. Electrochemical measurements, x-ray photoelectron spectroscopy, and atom probe tomography analysis indicate that manganese addition enhanced the corrosion resistance of aluminum without participating in the surface oxidation. Furthermore, the selective dissolution of manganese was believed to increase the free volume at the metal/oxide interface to facilitate the formation of a denser, thinner oxide layer with closer to stoichiometry composition. Atomistic simulations showed that the oxide layer compactness increased, and defect density decreased with increasing free volume content in Al, resulting in enhanced barrier characteristics.

36 MATERIALS SCIENCE↗

Passive Rocket Diffuser Testing: Reacting Flow Performance of Four Second-Throat Geometries

Second-throat diffusers serve to isolate rocket engines from the effects of ambient back pressure. As one of the nation's largest rocket testing facilities, the performance and design limitations of diffusers are of great interest to NASA's Stennis Space Center. This paper describes a series of tests conducted on four diffuser configurations to better understand the effects of inlet geometry and throat area on starting behavior and boundary layer separation. The diffusers were tested for a duration of five seconds with a 1455-pound thrust, LO2/GH2 thruster to ensure they each reached aerodynamic steady state. The effects of a water spray ring at the diffuser exits and a water-cooled deflector plate were also evaluated. Static pressure and temperature measurements were taken at multiple axial locations along the diffusers, and Computational Fluid Dynamics (CFD) simulations were used as a tool to aid in the interpretation of data. The hot combustion products were confirmed to enable the diffuser start condition with tighter second throats than predicted by historical cold-flow data or the theoretical normal shock method. Both aerodynamic performance and heat transfer were found to increase with smaller diffuser throats. Spray ring and deflector cooling water had negligible impacts on diffuser boundary layer separation. CFD was found to accurately capture diffuser shock structures and full-flowing diffuser wall pressures, and the qualitative behavior of heat transfer. However, the ability to predict boundary layer separated flows was not consistent.

Jones, Daniel R.↗

Chemical solution deposition of ferroelectric lead lanthanum zirconate titanate films on base-metal foils.

Development of electronic devices with better performance and smaller size requires the passive components to be embedded within a printed wire board (PWB). The 'film-on-foil' approach is the most viable method for embedding these components within a PWB. We have deposited high-permittivity ferroelectric lead lanthanum zirconate titanate (Pb{sub 0.92}La{sub 0.08}Zr{sub 0.52}Ti{sub 0.48}O{sub x}, PLZT 8/52/48) films on base metal foils by chemical solution deposition. These prefabricated capacitor sheets can be embedded into PWBs for power electronic applications. To eliminate the parasitic effect caused by the formation of a low-permittivity interfacial oxide, a conductive buffer layer of lanthanum nickel oxide (LNO) was applied by chemical solution deposition on nickel foil before the deposition of PLZT. With a {approx} 0.7-{micro}m-thick ferroelectric PLZT film grown on LNO-buffered nickel foil, we measured capacitance densities of 1.5 {micro}F/cm{sup 2}, breakdown field strength E{sub b} > 1.2 MV/cm, and leakage current density of 2 x 10{sup -8}A/cm{sup 2}. The dielectric relaxation current decay obeys the Curie-von Schweidler law, with exponent n = 0.85 and 0.94 for PLZT grown directly on Ni and that grown on LNO-buffered Ni foils, respectively. When compared with samples deposited directly on Ni substrate, PLZT grown on LNO buffered Ni substrates exhibit slimmer hysteresis loop and better energy storage capability. With these desirable characters, PLZT film-on-foil capacitors hold particular promise for use in high-voltage embedded passives.

36 MATERIALS SCIENCE↗

Deciphering the Cathode-Electrolyte Interfacial Chemistry in Sodium Layered Cathode Materials

The ever–increasing demand for stationary energy storage has driven the prosperous investigation of low–cost sodium ion batteries. The inferior long–term cycling stability of cathode materials is a significant roadblock toward the wide commercialization of sodium ion batteries. This study enlightens a path toward empowering stable sodium ion batteries through incisive diagnostics of the multiscale surface chemical processes in layered oxide materials (e.g., O3–NaNi 1/3 Fe 1/3 Mn 1/3 O 2 ). The major challenges are unraveled in a promising sodium layered cathode material using a range of complementary advanced spectroscopic and imaging diagnostic techniques. It is discovered that the cathode–electrolyte interfacial reaction triggers transition metal reduction, heterogeneous surface reconstruction, metal dissolution, and formation of intragranular nanocracks. These surface chemistry driven processes are partly responsible for significant performance decay. This diagnostic study also rationalizes the elemental substitution and surface passivation methods that are widely applied in the field. The prepassivated and Ti–substituted cathode materials allow for significantly improved cycling stability by inhibiting the metal dissolution. Furthermore, incisively diagnosing the interfacial chemistry not only creates scientific insights into understanding sodium cathode chemistry, but also represents an advance toward establishing universal interfacial design principles for all alkali metal ion cathode materials.

25 ENERGY STORAGE↗

High efficiency screen-printed n-type silicon solar cell using co-diffusion of APCVD boron emitter and POCl 3 back surface field

We present the fabrication and analysis of Passivated Emitter and Rear Totally Diffused (PERT) solar cells on n-type silicon using a co-diffusion process. In a single high temperature step, a BSG/SiO x stack deposited by APCVD and a POCl 3 back surface field diffuse into the wafer to form the boron doped emitter and phosphorus doped back surface field. The SiO x layer on top of BSG acts as a masking layer to prevent cross-doping of phosphorus as well as a blocking layer for boron out-diffusion. This resulted in an initial sheet resistance of 76 Ω with good uniformity and a final p + emitter sheet resistance of 97 Ω after boron rich layer removal. Additionally, bulk lifetime was investigated before and after the high temperature step that resulted in an increase from 1.2 ms to 1.5 ms due to a POCl 3 gettering effect. Finally, a peak cell efficiency of 20.3% was achieved and each recombination component in terms of saturation current density was calculated and analyzed to understand the cell for further efficiency enhancement.

14 SOLAR ENERGY↗

Desorption of Ag from Grain Boundaries in Ag Film on Br and H-Passivated Si(111) Surfaces

Growth of Ag film on Br- and H-passivated Si(111) surfaces was examined by Rutherford backscattering spectrometry (RBS), scanning electron microscopy (SEM) and photoemission electron microscopy (PEEM) techniques. The phenomenon of thermal grooving was observed after annealing at higher temperatures. Hierarchical desorption of Ag from the grain boundaries produce a fractal structure of Ag-depleted regions. Hierarchical desorption may be used for nanopatterning of the layer.

36 MATERIALS SCIENCE↗

Performance optimization of solar cells based on colloidal lead sulfide nanocrystals

Colloidal semiconducting quantum dot nanocrystals (NCs) have attracted extensive interest as active building-block for low-cost solution-processed photovoltaic due to their size tunable absorption from the visible to near IR. Among various nanocrystal composition, lead sulfide (PbS), having a bulk bandgap of 0.41 eV, are particularly attractive for photovoltaic applications due to their excellent photosensitivity in the near IR. Starting from colloidal synthesis, in this project functional solar cells are fabricated and characterized based on the nearly monodispersed colloidal PbS nanocrystals that we synthesized. These NC-solar cells are fabricated under a “depleted heterojunction” device architecture containing a planar “tipe II” heretojunction formed by a layer of electron-transporting TiO{sub 2} and a layer of PbS NCs. Relevant structural, optical, and electrical characterizations are performed on NCs and their devices. To understand the operational mechanism of these NC-based solar cells, various material and device aspects are investigated in this work aiming for optimized photovoltaic performance. These aspects include the effect of: (1) NC dimensions (and thus their band gaps); (2) passivation of surface traps through post-synthesis treatments; (3) NC surface ligand-exchange; and (4) interfacial modifications at the heterojunction. The most optimized photovoltaic performance is found after combining the surface trap passivation strategy by halides, ligand-exchange by 3-mercaptopropionic acids, and interfacial TiCl4 treatment, leading to a peak open-circuit voltage of 0.53 V, a short-circuit current density of 14.03 mAcm{sup −2}, and a power conversion efficiency of 3.25%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recent advances of two-dimensional material additives in hybrid perovskite solar cells

Perovskite solar cells (PSCs) have become one of the state-of-the-art photovoltaic technologies due to their facile solution-based fabrication processes combined with extremely high photovoltaic performance originating from excellent optoelectronic properties such as strong light absorption, high charge mobility, long free charge carrier diffusion length, and tunable direct bandgap. However, the poor intrinsic stability of hybrid perovskites under environmental stresses including light, heat, and moisture, which is often associated with high defect density in the perovskite, has limited the large-scale commercialization and deployment of PSCs. The use of process additives, which can be included in various subcomponent layers in the PSC, has been identified as one of the effective approaches that can address these issues and improve the photovoltaic performance. Among various additives that have been explored, two-dimensional (2D) materials have emerged recently due to their unique structures and properties that can enhance the photovoltaic performance and device stability by improving perovskite crystallization, defect passivation, and charge transport. In this work, we provide a review of the recent progresses in 2D material additives for improving the PSC performance based on key representative 2D material systems, including graphene and its derivatives, transitional metal dichalcogenides, and black phosphorous, providing a useful guideline for further exploiting unique nanomaterial additives for more efficient and stable PSCs in the near future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Heat-activated Plasmonic Chemical Sensors for Harsh Environments

A passive plasmonics based chemical sensing system to be used in harsh operating environments was investigated and developed within this program. The initial proposed technology was based on combining technologies developed at the SUNY Polytechnic Institute Colleges of Nanoscale Science and Engineering (CNSE) and at the University of Minnesota (UM). Specifically, a passive wireless technique developed at UM was to utilize a heat-activated plasmonic design to passively harvest the thermal energy from within a combustion emission stream and convert this into a narrowly focused light source. This plasmonic device was based on a bullseye design patterned into a gold film using focused ion beam methods (FIB). Critical to the design was the use of thermal stabilizing under and overlayers surrounding the gold film. These stabilizing layers were based on both atomic layer deposited films as well as metal laminate layers developed by United Technologies Aerospace Systems (UTAS). While the bullseye design was never able to be thermally stabilized for operating temperatures of 500oC or higher, an alternative energy harvesting design was developed by CNSE within this program. With this new development, plasmonic sensing results are presented where thermal energy is harvested using lithographically patterned Au nanorods, replacing the need for an external incident light source. Gas sensing results using the harvested thermal energy are in good agreement with sensing experiments, which used an external incident light source. Principal Component Analysis (PCA) was used to reduce the wavelength parameter space from 665 variables down to 4 variables with similar levels of demonstrated selectivity. The method was further improved by patterning rods which harvested energy in the near infrared, which led to a factor of 10 decrease in data acquisition times as well as demonstrated selectivity with a reduced wavelength data set. The combination of a plasmonic-based energy harvesting sensing paradigm with PCA analysis and wavelength down selection offers a novel path towards simplification and integration of plasmonic-based sensing methods using selected wavelengths rather than a full spectral analysis. Integration efforts were designed and modeled for thermal and mass transport considerations by UTAS which led to the 3D printing of scaled models that would serve as the housing for the alternative energy harvesting plasmonic chemical sensor design developed by CNSE.

47 OTHER INSTRUMENTATION↗

Microwave response of snow

Truck-mounted microwave sensors were used to acquire backscattering coefficient and apparent temperature data for snow-covered terrain at 19 frequencies between 1 and 18 GHz and at 35.6 GHz. Passive microwave measurements were made at 10.7, 37, and 94 GHz. The radar backscattering coefficient and radiometric emissivity were evaluated as a function of snow depth, wetness, surface roughness, and other snow parameters. It is shown that volume scattering makes the radar backscattering coefficient to increase and the radiometric emissivity to decrease with increasing snow depth until the snow layer appears electromagnetically semiinfinite in extent. The presence of liquid water in the snowpack results in increased attenuation and reduction in scattering which leads to less backscatter and more emission by the snow volume. It is concluded that microwave sensors have the potential capability for remotely monitoring both the snow equivalent and wetness of snowpacks.

Ulaby, F. T.↗

On the Effects of Wind Turbine Wake Skew Caused by Wind Veer: Preprint

Because of Coriolis forces caused by the Earth's rotation, the structure of the atmospheric boundary layer often contains wind-direction change with height, also known as wind-direction veer. Under low turbulence conditions, such as in stably stratified atmospheric conditions, this veer can be significant, even across the vertical extent of a wind turbine's rotor disk. The veer then causes the wind turbine wake to skew as it advects downstream. This wake skew has been observed both experimentally and numerically. In this work, we attempt to examine the wake skewing process in some detail, and quantify how differently a skewed wake versus a non skewed wake affects a downstream turbine. We do this by performing atmospheric large-eddy simulations to create turbulent inflow winds with and without veer. In the veer case, there is a roughly 8 degree wind direction change across the turbine rotor. We then perform subsequent large-eddy simulations using these inflow data with an actuator line rotor model to create wakes. The turbine modeled is a large, modern, offshore, multimegawatt turbine. We examine the unsteady wake data in detail and show that the skewed wake recovers faster than the non skewed wake. We also show that the wake deficit does not skew to the same degree that a passive tracer would if subject to veered inflow. Last, we use the wake data to place a hypothetical turbine 9 rotor diameters downstream by running aeroelastic simulations with the simulated wake data. We see differences in power and loads if this downstream turbine is subject to a skewed or non skewed wake. We feel that the differences observed between the skewed and nonskewed wake are important enough that the skewing effect should be included in engineering wake models.

17 WIND ENERGY↗

Effects of corn stalk orientation and water content on passive microwave sensing of soil moisture

A field experiment was conducted utilizing artificial arrangements of plant components during the summer of 1982 to examine the effects of corn canopy structure and plant water content on microwave emission. Truck-mounted microwave radiometers at C (5 GHz) and L (1.4 GHz) band sensed vertically and horizontally polarized radiation concurrent with ground observations of soil moisture and vegetation parameters. Results indicate that the orientation of cut stalks and the distribution of their dielectric properties through the canopy layer can influence the microwave emission measured from a vegetation/soil scene. The magnitude of this effect varies with polarization and frequency and with the amount of water in the plant, disappearing at low levels of vegetation water content. Although many of the canopy structures and orientations studied in this experiment are somewhat artificial, they serve to improve understanding of microwave energy interactions within a vegetation canopy and to aid in the development of appropriate physically based vegetation models.

Oneill, P. E.↗