Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Relief of Residual Stress in Streamline Tie Rods by Heat Treatment

About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees fahrenheit. Columbium-treated and molybdenum-treated 18:8 steel exhibited improved stability over a wide range of temperatures. Tie rods of either material could be heated 30 minutes with safety at any temperature up to 1000 degrees Fahrenheit. At this temperature most of the residual stress would be relieved.

Pollard, R E↗

Stress analysis of circular semimonocoque cylinders with cutouts by a perturbation load technique

A method is presented for analyzing the stresses about a cutout in a circular cylinder of semimonocoque construction. The method involves the use of so-called perturbation solutions which are superposed on the stress distribution that would exist in the structure with no cutout in such a way as to give the effects of a cutout. The method can be used for any loading case for which the structure without the cutout can be analyzed and is sufficiently versatile to account for stringer and shear reinforcement about the cutout. (author)

Mccomb, Harvey G , Jr↗

Investigations of Air-cooled Turbine Rotors for Turbojet Engines II : Mechanical Design, Stress Analysis, and Burst Test of Modified J33 Split-disk Rotor / Richard H. Kemp and Merland L. Moseson

A full-scale J33 air-cooled split turbine rotor was designed and spin-pit tested to destruction. Stress analysis and spin-pit results indicated that the rotor in a J33 turbojet engine, however, showed that the rear disk of the rotor operated at temperatures substantially higher than the forward disk. An extension of the stress analysis to include the temperature difference between the two disks indicated that engine modifications are required to permit operation of the two disks at more nearly the same temperature level.

TURBINES - WHEELS, DISK - STRENGTH↗

Analysis of wing truss stresses including the effect of redundancies

Airplane wing trusses are generally designed to contain redundant members (stagger wires and external drag wires) which, according to common practice, are not taken into account in calculations, so as to simplify the stress analysis by rendering the structure statically determinate. A more accurate method, in which the redundancies are included, involves a solution by means of Castigliano's method of least work. For the purpose of demonstrating the practical application of the method of least work this report presents examples for stresses of several cases of loading worked out for a structure similar to that of the Curtiss JN-4h. Case 1 was taken as the condition of velocity of 100 miles per hour combined with the angle of attack of maximum lift. Case 1a assumed the same loading but neglected the distortion of wooden members in the least-work analysis. So little error was involved in case 1a that this simplified method was employed for each succeeding case. Case 2 assumed a diving speed of 120 miles per hour and an angle of attack of no lift. Case 3 was worked out for the conditions imposed by the sand load recommended in NACA technical note no. 6.

Warner, E P↗

Bending moments, envelope, and cable stresses in non-rigid airships

This report describes the theory of calculating the principal stresses in the envelope of a nonrigid airship used by the Bureau of Aeronautics, United States Navy. The principal stresses are due to the gas pressure and the unequal distribution of weight and buoyancy, and the concentrated loads from the car suspension cables. The second part of the report deals with the variations of tensions in the car suspension cables of any type of airship, with special reference to the rigid type, due to the propeller thrust or the inclination of the airship longitudinally.

Burgess, C P↗

Determination of elastic stresses in gas-turbine disks

A method is presented for the calculation of elastic stresses in symmetrical disks typical of those of a high-temperature gas turbine. The method is essentially a finite-difference solution of the equilibrium and compatibility equations for elastic stresses in a symmetrical disk. Account can be taken of point-to-point variations in disk thickness, in temperature, in elastic modulus, in coefficient of thermal expansion, in material density, and in Poisson's ratio. No numerical integration or trial-and-error procedures are involved and the computations can be performed in rapid and routine fashion by nontechnical computers with little engineering supervision. Checks on problems for which exact mathematical solutions are known indicate that the method yields results of high accuracy. Illustrative examples are presented to show the manner of treating solid disks, disks with central holes, and disks constructed either of a single material or two or more welded materials. The effect of shrink fitting is taken into account by a very simple device.

Manson, S S↗

Behavior of Materials Under Conditions of Thermal Stress

A review is presented of available information on the behavior of brittle and ductile materials under conditions of thermal stress and thermal shock. For brittle materials, a simple formula relating physical properties to thermal-shock resistance is derived and used to determine the relative significance of two indices currently in use for rating materials. For ductile materials, thermal-shock resistance depends upon the complex interrelation among several metallurgical variables which seriously affect strength and ductility. These variables are briefly discussed and illustrated from literature sources. The importance of simulating operating conditions in tests for rating materials is especially to be emphasized because of the importance of testing conditions in metallurgy. A number of practical methods that have been used to minimize the deleterious effects of thermal stress and thermal shock are outlined.

Manson, S S↗

Statistical analysis of service stresses in aircraft wings

On the wing structures of modern high speed aircraft, in particular, the comparatively high-service stresses and the consistently increasing number of hours of operation during the life of the separate airplane parts make the studies of strength requirement under recurrent stresses appear of major concern. The DVL has therefore made exhaustive studies for this structural group of airplanes, some results of which are reported here.

Kaul, Hans W↗

The Influence of Notches Under Static Stress

From the described experiments it is seen that notches are a potential source of strength decrease even under static stress, which the designer must take into consideration. Section I is a general treatment of notch influence under the various types of stresses. Section II treats the influence of notches in thin sheet as is used in airplane construction.

Matthaes, K↗

Torsional stresses in box beams with cross sections partially restrained against warping

The present report gives a method for computing the torsion of boxes with thin shear-resistant or simply tension-resistant walls under any torsional load, support and dimension. The final stress condition is developed from that of a principal system with unconstrained sectional warping corresponding to Bredt's formula and an additional stress condition due to constrained cross-sectional warping. This is computed by means of the deflection condition of the principal system from a statically indeterminate calculation. Conformably, the torsional rigidity of the final system is derived from that of the principal system with unconstrained sectional buckling.

Ebner, Hans↗

Wrinkling of reinforced plates subjected to shear stresses

An analysis is made here of the problem of long plates with transverse stiffeners subject to shear. A typical example would be a long Wagner beam. The shear stress is calculated at which the web wrinkles and shear stress becomes a maximum. The equation is solved for both a condition of free support and rigidity of support on the edges.

Seydel, Edgar↗

Deflection And Stress In Preloaded Rectangular Membrane

Theoretical analysis yields equations for transverse deflection of, and stresses in, rectangular membrane subject to transverse pressure load and to tensile preloads applied uniformly along edges. This is extension of analysis reported in "Deflection and Stress in Preloaded Square Membrane" (GSC-13367).

Hermida, Alfonso↗

Refined Estimation Of Thermal Tensile Stresses In Bolts

Thermal changes in tensile stresses and strains in bolt and in corresponding compressive stresses and strains in bolted material estimated more accurately by use of equations incorporating two refinements over previous equations. Elasticity of bolted material and radial thermal expansion also taken into account. Refined equations improve design and analysis of bolted joints assembled at one temperature (e.g., room temperature) and in which specified minimum tension must be maintained (and/or specified maximum tension not exceeded) at higher or lower operational temperature.

Rash, Larry C.↗

Stress corrosion cracking properties of 15-5PH steel

Unexpected occurrence of failures, due to stress corrosion cracking (SCC) of structural components, indicate a need for improved characterization of materials and more advanced analytical procedures for reliably predicting structures performance. Accordingly, the purpose of this study was to determine the stress corrosion susceptibility of 15-5PH steel over a wide range of applied strain rates in a highly corrosive environment. The selected environment for this investigation was a highly acidified sodium chloride (NaCl) aqueous solution. The selected alloy for the study was a 15-5PH steel in the H900 condition. The slow strain rate technique was selected to test the metals specimens.

Rosa, Ferdinand↗

Time dependent behavior of a graphite/thermoplastic composite and the effects of stress and physical aging

Two complimentary studies were performed to determine the effects of stress and physical aging on the matrix dominated time dependent properties of IM7/8320 composite. The first of these studies, experimental in nature, used isothermal tensile creep/aging test techniques developed for polymers and adapted them for testing of the composite material. From these tests, the time dependent transverse (S22) and shear (S66) compliance's for an orthotropic plate were found from short term creep compliance measurements at constant, sub-T(sub g) temperatures. These compliance terms were shown to be affected by physical aging. Aging time shift factors and shift rates were found to be a function of temperature and applied stress. The second part of the study relied upon isothermal uniaxial tension tests of IM7/8320 to determine the effects of physical aging on the nonlinear material behavior at elevated temperature. An elastic/viscoplastic constitutive model was used to quantify the effects of aging on the rate-independent plastic and rate-dependent viscoplastic response. Sensitivity of the material constants required by the model to aging time were determined for aging times up to 65 hours. Verification of the analytical model indicated that the effects of prior aging on the nonlinear stress/strain/time data of matrix dominated laminates can be predicted.

Gates, Thomas S.↗

A representation for the turbulent mass flux contribution to Reynolds-stress and two-equation closures for compressible turbulence

The turbulent mass flux, or equivalently the fluctuating Favre velocity mean, appears in the first and second moment equations of compressible kappa-epsilon and Reynolds stress closures. Mathematically it is the difference between the unweighted and density-weighted averages of the velocity field and is therefore a measure of the effects of compressibility through variations in density. It appears to be fundamental to an inhomogeneous compressible turbulence, in which it characterizes the effects of the mean density gradients, in the same way the anisotropy tensor characterizes the effects of the mean velocity gradients. An evolution equation for the turbulent mass flux is derived. A truncation of this equation produces an algebraic expression for the mass flux. The mass flux is found to be proportional to the mean density gradients with a tensor eddy-viscosity that depends on both the mean deformation and the Reynolds stresses. The model is tested in a wall bounded DNS at Mach 4.5 with notable results.

Ristorcelli, J. R.↗

Prediction of stress-strain response of SCS-6/Timetal-21S subjected to a hypersonic flight profile

Thermomechanical response of a cross-ply SCS-6/Timetal-21S composite subjected to a generic hypersonic flight profile with the temperature ranging from -130 C to 816 C was evaluated experimentally and analytically. A two dimensional micromechanical anlaysis, VISCOPLY, was used to predict the stress-strain response of the laminate and of the constituents in each ply during thermomechanical loading conditions. In the analysis, the fiber was modeled as elastic with transverse orthotropic and temperature dependent properties and the matrix was modeled using a thermoviscoplastic constitutive relation. The fiber transverse modulus was reduced in the analysis to simulate fiber-matrix interface failure. Reasonable agreement was found between measured and predicted laminate stress-strain response when fiber-matrix debonding was modeled.

Mirdamadi, Massoud↗

Effects of assumed tow architecture on the predicted moduli and stresses in woven composites

This study deals with the effect of assumed tow architecture on the elastic material properties and stress distributions of plain weave woven composites. Specifically, the examination of how a cross-section is assumed to sweep-out the tows of the composite is examined in great detail. The two methods studied are extrusion and translation. This effect is also examined to determine how sensitive this assumption is to changes in waviness ratio. 3D finite elements were used to study a T300/Epoxy plain weave composite with symmetrically stacked mats. 1/32nd of the unit cell is shown to be adequate for analysis of this type of configuration with the appropriate set of boundary conditions. At low waviness, results indicate that for prediction of elastic properties, either method is adequate. At high waviness, certain elastic properties become more sensitive to the method used. Stress distributions at high waviness ratio are shown to vary greatly depending on the type of loading applied. At low waviness, both methods produce similar results.

Chapman, Clinton Dane↗