Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Experimental and analytical study of the hydrodynamic and single and two-phase convective heat transfer performance of flexible PDMS microchannels with micropillar arrays

Various copper and silicon based thermal management systems are used in the cooling of electronics. However, the rigid nature of these materials along with their high thermal and electrical conductivity pose a difficulty in developing direct contact embedded flexible cooling systems that can offer robust cooling performance. The low density, thermal stability, chemical inertness, and electrical insulation of Polydimethylsiloxane (PDMS) make it an ideal material to develop lightweight direct contact thermal management systems for electronics. Its ease of fabrication with tunable flexibility provides the opportunity to go beyond traditional electronics and develop advanced active and passive thermal management systems for a wide–range of applications in foldable and wearable electronics, liquid cooling garments, microgravity, and electric motors. In this study, a flexible PDMS based microchannel with micropillar arrays, which enhance the thermal performance of the device through capillary-assisted flow, has been developed. The hydrodynamic and convection heat transfer performance of three PDMS wick pillar geometries, ranging from a porosity of 0.8–0.91, are investigated and compared under single-phase and two-phase conditions. Dielectric coolant FC-3283 is employed and permeability measurements are made for mass fluxes ranging from 53 kg/m 2 s to 369 kg/m 2 s. Given its conformability, the device demonstrates a deviation from Darcy’s Law, within the laminar regime, with an increasing permeability with mass flux at the rate of ~0.5–0.8 Darcy/(kg/m 2 s). A semi-analytical model has been developed and reported to quantify the conformability of the device. The heat transfer performance is experimentally evaluated using the same dielectric fluid for mass flux ranging from 105 kg/m 2 s to 420 kg/m 2 s with heat fluxes ranging from 1.5 W/cm 2 to 16 W/cm 2 . Heat transfer coefficients of up to 7000 W/m 2 K are observed, which are comparable to copper and silicon microchannels. The effect of porosity on the single phase thermal performance has been evaluated against the pumping power to provide a basis for thermal management system design. Finally, high-speed imaging is performed to study the two-phase flow characteristics to provide insight into the vapor formation and removal.

42 ENGINEERING↗

Unique and analogous functions of aquaporin O for fiber cell architecture and ocular lens transparency

Aquaporin (AQP) 1 and AQP0 water channels are expressed in lens epithelial and fiber cells, respectively, facilitating fluid circulation for nourishing the avascular lens to maintain transparency. Even though AQP0 water permeability is 40-fold less than AQP1, AQP0 is selectively expressed in the fibers. Delimited AQP0 fiber expression is attributed to a unique structural role as an adhesion protein. To validate this notion, we determined if wild type (WT) lens ultrastructure and fibercell adhesion are different in AQP0{sup -/-}, and TgAQP1{sup +/+}/AQP0{sup -/-} mice that transgenically express AQP1 (TgAQP1) in fibercells without AQP0 (AQP0{sup -/-}). In WT, lenses were transparent with 'Y' sutures. Fibers contained opposite end curvature, lateral interdigitations, hexagonal shape, and were arranged as concentric growth shells. AQP0{sup -/-}lenses were cataractous, lacked 'Y' sutures, ordered packing and well-defined lateral interdigitations. TgAQP1{sup +/+}/AQP0{sup -/-} lenses showed improvement in transparency and lateral interdigitations in the outer cortex while inner cortex and nuclear fibers were severely disintegrated. Transmission electron micrographs exhibited tightly packed fibercells in WT whereas AQP0{sup -/-} and TgAQP1{sup +/+}/AQP0{sup -/-}lenses had wide extracellular spaces. Fibers were easily separable by teasing in AQP0{sup -/-} and TgAQP1{sup +/+}/AQP0{sup -/-}lenses compared to WT. Our data suggest that the increased water permeability through AQP1 does not compensate for loss of AQP0 expression in TgAQP1{sup +/+}/AQP0{sup -/-} mice. Fibercell AQP0 expression is required to maintain their organization, which is a requisite for lenstransparency. AQP0 appears necessary for cell-to-cell adhesion and thereby to minimize light scattering since in the AQP0{sup -/-} and TgAQP1{sup +/+}/AQP0{sup -/-} lenses, fiber cell disorganization was evident.

59 BASIC BIOLOGICAL SCIENCES↗

Albendazole inhibits endothelial cell migration, tube formation, vasopermeability, VEGF receptor-2 expression and suppresses retinal neovascularization in ROP model of angiogenesis

The angiogenic process begins with the cell proliferation and migration into the primary vascular network, and leads to vascularization of previously avascular tissues and organs as well to growth and remodeling of the initially homogeneous capillary plexus to form a new microcirculation. Additionally, an increase in microvascular permeability is a crucial step in angiogenesis. Vascular endothelial growth factor (VEGF) plays a central role in angiogenesis. We have previously reported that albendazole suppresses VEGF levels and inhibits malignant ascites formation, suggesting a possible effect on angiogenesis. This study was therefore designed to investigate the antiangiogenic effect of albendazole in non-cancerous models of angiogenesis. In vitro, treatment of human umbilical vein endothelial cells (HUVECs) with albendazole led to inhibition of tube formation, migration, permeability and down-regulation of the VEGF type 2 receptor (VEGFR-2). In vivo albendazole profoundly inhibited hyperoxia-induced retinal angiogenesis in mice. These results provide new insights into the antiangiogenic effects of albendazole.

60 APPLIED LIFE SCIENCES↗

Tumor associated osteoclast-like giant cells promote tumor growth and lymphangiogenesis by secreting vascular endothelial growth factor-C

Highlights: • M-CSF and RANKL expressing HeLa cells induced osteoclastogenesis in vitro. • We established OGC-containing tumor model in vivo. • OGC-containing tumor became larger independent of M-CSF or RANKL effect. • VEGF-C secreted from OGCs was a one of candidates for OGC-containing tumor growth. - Abstract: Tumors with osteoclast-like giant cells (OGCs) have been reported in a variety of organs and exert an invasive and prometastatic phenotype, but the functional role of OGCs in the tumor environment has not been fully clarified. We established tumors containing OGCs to clarify the role of OGCs in tumor phenotype. A mixture of HeLa cells expressing macrophage colony-stimulating factor (M-CSF, HeLa-M) and receptor activator of nuclear factor-κB ligand (RANKL, HeLa-R) effectively supported the differentiation of osteoclast-like cells from bone marrow macrophages in vitro. Moreover, a xenograft study showed OGC formation in a tumor composed of HeLa-M and HeLa-R. Surprisingly, the tumors containing OGCs were significantly larger than the tumors without OGCs, although the growth rates were not different in vitro. Histological analysis showed that lymphangiogenesis and macrophage infiltration in the tumor containing OGCs, but not in other tumors were accelerated. According to quantitative PCR analysis, vascular endothelial growth factor (VEGF)-C mRNA expression increased with differentiation of osteoclast-like cells. To investigate whether VEGF-C expression is responsible for tumor growth and macrophage infiltration, HeLa cells overexpressing VEGF-C (HeLa-VC) were established and transplanted into mice. Tumors composed of HeLa-VC mimicked the phenotype of the tumors containing OGCs. Furthermore, the vascular permeability of tumor microvessels also increased in tumors containing OGCs and to some extent in VEGF-C-expressing tumors. These results suggest that macrophage infiltration and vascular permeability are possible mediators in these tumors. These findings revealed that OGCs in the tumor environment promoted tumor growth and lymphangiogenesis, at least in part, by secreting VEGF-C.

60 APPLIED LIFE SCIENCES↗

Suppressive effects of lysozyme on polyphosphate-mediated vascular inflammatory responses

Lysozyme, found in relatively high concentration in blood, saliva, tears, and milk, protects us from the ever-present danger of bacterial infection. Previous studies have reported proinflammatory responses of endothelial cells to the release of polyphosphate(PolyP). In this study, we examined the anti-inflammatory responses and mechanisms of lysozyme and its effects on PolyP-induced septic activities in human umbilical vein endothelial cells (HUVECs) and mice. The survival rates, septic biomarker levels, behavior of human neutrophils, and vascular permeability were determined in PolyP-activated HUVECs and mice. Lysozyme suppressed the PolyP-mediated vascular barrier permeability, upregulation of inflammatory biomarkers, adhesion/migration of leukocytes, and activation and/or production of nuclear factor-κB, tumor necrosis factor-α, and interleukin-6. Furthermore, lysozyme demonstrated protective effects on PolyP-mediated lethal death and the levels of the related septic biomarkers. Therefore, these results indicated the therapeutic potential of lysozyme on various systemic inflammatory diseases, such as sepsis or septic shock. -- Highlights: •PolyP is shown to be an important mediator of vascular inflammation. •Lysozyme inhibited PolyP-mediated hyperpermeability. •Lysozyme inhibited PolyP-mediated septic response. •Lysozyme reduced PolyP-induced septic mortality.

60 APPLIED LIFE SCIENCES↗

Computational Insights into Fuels and Chemicals Extraction from Microbial Biorefineries

Over the past two decades, substantial investments have been made in engineering microorganisms to produce specific fuels and chemicals as part of the global bioeconomy. Many target molecules accumulate intracellularly, and a challenge is how to effectively extract the product from the cells without needing to destroy them due to the barrier imposed by the cell membrane. For some hydrophobic compounds, an organic overlay is an effective strategy for nondestructive product extraction, although the relationship between functional groups on the product and the rate of extraction are not well understood. Through both biased and unbiased molecular dynamics simulations for a range of fatty acyl compounds and terpenoids, we directly compute permeability coefficients for different steps of the extraction process. Via comparative analysis between the calculated permeability coefficients and observed interactions between the compounds and the membrane, we determine how the rate limiting steps vary depending on product chemistry. For instance, fatty aldehydes are found to transfer very rapidly across the membrane bilayer relative to alcohols, although their comparable rate of extraction into the organic phase makes them equally effective at extraction from the cell. In assessing the terpenoids, it is found that in general a modestly hydrophilic product improves desorption rates into an organic phase sufficiently to make up for their lower bilayer crossing rate. With this new insight, we can more effectively engineer microorganisms towards the production of these modestly hydrophilic fuel precursors or chemicals.

09 BIOMASS FUELS↗

Separation of Dimethyl Ether from Syn-Gas Components by Poly(dimethylsiloxane) and Poly(4-methyl-1-pentene) Membranes

Permeability and selectivity in gas transport through poly(4-methyl-1-pentene) (TPX) and poly(dimethylsiloxane) (PDMS) using variable temperature mixed gas experiments is reported. Selected gases include H2, CO, CH4, CO2, and dimethyl ether (DME). The DME data is the first to be reported through these membranes. In this paper, the chosen polymers reflect both rubbery and crystalline materials. Rubbery polymers tend to be weakly size sieving, which, in this work, has resulted in larger permeabilities, lower separation factors, and lower activation energies of permeation (Ep). Conversely, the crystalline TPX membranes showed much greater sensitivity to penetrant size; although the gas condensability also played a role in transport.

36 MATERIALS SCIENCE↗

Visualization of water penetration in cementitious materials with superabsorbent polymers by means of neutron radiography

Concrete cracks due to its low tensile strength. As both harmful gases and fluids may enter the concrete by migrating into cracks, the durability is endangered. The service life decreases, repair costs rise and buildings could structurally decline. In the current research, crack sealing is enhanced by the use of superabsorbent polymers (SAP). When cracking occurs, SAP particles are exposed to the humid environment and swell, sealing the crack. By means of neutron radiography, the moisture distribution is studied during capillary absorption and water permeability tests. Capillary absorption in a crack and water permeability through a crack are reduced in specimens containing SAP particles. SAP particles are able to seal the crack, thus allowing a recovery of the water-tightness of the structure. The total uptake of potentially harmful substances hereby lowers, leading to an enhanced long-term durability and lower maintenance costs.

36 MATERIALS SCIENCE↗

Self-healing concrete by use of microencapsulated bacterial spores

Microcapsules were applied to encapsulate bacterial spores for self-healing concrete. The viability of encapsulated spores and the influence of microcapsules on mortar specimens were investigated first. Breakage of the microcapsules upon cracking was verified by Scanning Electron Microscopy. Self-healing capacity was evaluated by crack healing ratio and the water permeability. The results indicated that the healing ratio in the specimens with bio-microcapsules was higher (48%–80%) than in those without bacteria (18%–50%). The maximum crack width healed in the specimens of the bacteria series was 970 μm, about 4 times that of the non-bacteria series (max 250 μm). The overall water permeability in the bacteria series was about 10 times lower than that in non-bacteria series. Wet–dry cycles were found to stimulate self-healing in mortar specimens with encapsulated bacteria. No self-healing was observed in all specimens stored at 95%RH, indicating that the presence of liquid water is an essential component for self-healing.

36 MATERIALS SCIENCE↗

Investigation of the changes in microstructure and transport properties of leached cement pastes accounting for mix composition

Ca-leaching of cement-based materials induces detrimental effects on properties related to long-term durability. A better understanding of leaching degradation in terms of alterations in mineralogy, microstructure, and transport properties is important for long-term assessments of concrete and reinforced concrete structures used in nuclear waste disposal systems or in hydro structures. However, the decalcification process is not easy to study because it is extremely slow. In this study, an ammonium nitrate (NH{sub 4}NO{sub 3}) solution of 6 mol/l was used to accelerate the leaching kinetics. The experiments were performed on cement paste samples with different water/powder (w/p) and limestone filler (LS) replacement ratios. Both the change of sample mass over time and the amount of calcium ion leached out were monitored during the test. Different post-analysis techniques including SEM/SEM-EDX, XRD/QXRD, MIP, ion chromatography, and N{sub 2}-adsorption were used to characterize the microstructural and mineralogical changes. The effect of accelerated leaching on transport properties was studied by measuring the changes in water permeability and diffusivity of dissolved gases. Results showed that the square-root-time law of degradation was applicable under accelerated conditions. Both higher w/p ratios and LS replacements increased the rate of leaching propagation; the former had a more significant effect. The accelerated leaching significantly altered the microstructure of the cement paste to a material with a higher specific surface area, increased total porosity and a shift to larger pore sizes. Those changes led to a significant increase in water permeability (one to two orders of magnitude) and diffusivity (less than one order) depending on degradation state.

36 MATERIALS SCIENCE↗

Silica-modifying chemical admixtures for directed zeolitization of metakaolin-based alkali-activated materials

The effect of using trimethyladamantyl-ammonium hydroxide (TMAAOH) as a silica-modifying admixture to induce early-age mineralization during alkali-activation of metakaolin was investigated and reported herein. In all material formulations, the use of TMAAOH induced early-age mineralization, increased mixture stiffening in the fresh state, and lowered total heat of reaction. In activating solutions with silica moduli above unity (Ms >1.0), mineralogy results demonstrate that TMAAOH induces the nucleation and growth of metastable zeolitic phases, which correlated with increased permeability and increased plastic shrinkage of the paste. When TMAAOH was added to activating solutions with silica moduli near unity (Ms ~1.0), the controlled formation of crystalline, silica-rich faujasite was observed, which correlated with reduced permeability and lower plastic shrinkage. Together, these results demonstrate for the first time that silica-templating agents such as TMAAOH can be exploited in the design of new chemical admixtures that directly influence the dynamics of zeolitization in alkali-activated materials.

36 MATERIALS SCIENCE↗

Long-term strength retrogression of silica-enriched oil well cement: A comprehensive multi-approach analysis

The strength retrogression of a Class G cement enriched by adding 60–80% silica cured under the condition of 200 °C and 50 MPa were investigated by multiple different analysis methods. Short-term strength analysis suggests sonic strength testing is a poor indicator of real mechanical strength at such curing condition. Long-term testing up to 142 d shows all designed systems experiences dramatic deterioration in physical and mechanical properties, such as compressive strength, Young's modulus, water permeability and gas permeability. Further testing was conducted using X-ray diffraction, thermal gravimetric analysis, mercury intrusion and scanning electron microscope. The study reveals that the set cement experiences significant microstructure coarsening with increasing curing time, especially after 30 d curing. The strength retrogression and microstructure coarsening seem to be accompanied with the continued consumption of silica, and are likely caused by the gradual conversion of semi-crystalline C-S-H into crystalline tobermorite and xonolite over the long-term curing.

36 MATERIALS SCIENCE↗

Cement stress and microstructure evolution during curing in semi-rigid high-pressure environments

The process of cement slurry curing into a solid has a direct effect on the initial state of stress in a composite concrete and steel structure. Failure models for critical infrastructure and wellbores could benefit from measurements of this initial stress because it greatly influences structural performance. Here, we present measurements of the initial stress state (total stress, effective stress, and pore pressure) of multiple cement formulations cured under a high-pressure of 40 MPa within a semi-rigid steel pipe. Our results show that cements cured in this restrained environment exhibit dense microstructures with low permeability (nano-Darcy), develop an anisotropic stress state greater than zero and less than the curing pressure, and undergo a staged curing process where hydration and mechanical behaviors evolve from a slurry into a pre-stressed porous medium. Both drained and undrained scenarios were investigated, revealing a feedback from the semi-rigid boundary towards improved cement performance.

36 MATERIALS SCIENCE↗

Variability of geochemical properties in a microbially dominated coalbed gas system from the eastern margin of the Illinois Basin, USA

This study outlines gas characteristics along the southeastern margins of the Illinois Basin and evaluates regional versus local gas variations in Seelyville and Springfield coal beds. Our findings suggest that high permeability and shallow (100–250 m) depths of these Indiana coals allowed inoculation with methanogenic microbial consortia, thus leading to widespread microbial methane generation along the eastern marginal part of the Illinois Basin. Low maturity coals in the Illinois Basin with a vitrinite reflectance Ro~0.6% contain significant amounts of coal gas (~3 m3/t, 96 scf/t) with ≥97 vol.% microbial methane. The amount of coal gas can vary significantly within a coal seam both in a vertical seam section as well as laterally from location to location. Therefore sampling of an entire core section is required for accurate estimates of coal gas reserves.

01 COAL, LIGNITE, AND PEAT↗

Shrinkage and Swelling of Coal Induced by Desorption and Sorption of Fluids: Theoretical Model and Interpretation of a Field Project

Geologic sequestration in deep unmineable coal seams and enhanced coalbed methane production is a promising choice, economically and environmentally, to reduce anthropogenic gases such as carbon dioxide in the atmosphere. Unmineable coal seams are typically known to adsorb large amounts of carbon dioxide in comparison to the sizeable amounts of sorbed methane, which raises the potential for large scale sequestration projects. During the process of sequestration, carbon dioxide is injected into the coalbed and desorbed methane is produced. The coal matrix is believed to shrink when a gas is desorbed and swell when a gas is sorbed, sometimes causing profound changes in the cleat porosity and permeability of the coal seam. These changes may have significant impact on the reservoir performance. Therefore, it is necessary to understand the combined influence of swelling and shrinkage, and geomechanical properties including elastic modulus, cleat porosity, and permeability of the reservoir. The present paper deals with the influence of swelling and shrinkage on the reservoir performance, and the geomechanical response of the reservoir system during the process of geologic sequestration of carbon dioxide and enhanced coalbed methane production in an actual field project located in northern New Mexico. A three-dimensional swelling and shrinkage model was developed and implemented into an existing reservoir model to understand the influence of geomechanical parameters, as well as swelling and shrinkage properties, on the reservoir performance. Numerical results obtained from the modified simulator were compared to available measured values from that site and previous studies. Results show that swelling and shrinkage, and the combination of geomechanical and operational parameters, have a significant influence on the performance of the reservoir system.

01 COAL, LIGNITE, AND PEAT↗

Exploring the impact of hydro-mechanical coupling on compaction localization

In deep subsurface environments, where porous rocks are saturated with fluids, hydromechanical coupling plays a critical role in the formation and propagation of localized deformation zones, such as compaction bands. In this study, we numerically investigate the influence of fluid-rock interactions on the development of compaction localization in fluid-saturated rocks. For this purpose, it uses a numerical framework that adapts the heat equation to model the diffusion of pore pressure caused by deformation. This is achieved with specialized subroutines for material behavior and heat transfer formulated within the ABAQUS platform and by allowing changes in rock permeability during strain localization. The results highlight that hydromechanical coupling significantly alters the compaction behavior compared to dry conditions. Under high confining stress, excess pore pressure inhibits the progression of compaction fronts, while in time-dependent processes like rock creep, pore pressure transients accelerate deformation by creating feedback loops between mechanical forces and fluid flow. These findings underscore the importance of saturation in controlling the dynamics of compaction localization and provide insights into the interplay between pore pressure, deformation, and permeability. The implications of this study extend to applications in geological storage, resource extraction, and subsurface geomechanics, offering a deeper understanding of coupled hydromechanical processes in porous rocks.

58 GEOSCIENCES↗

Laboratory evaluation of cyclic underground hydrogen storage in the Temblor sandstone of the San Joaquin Basin, California

Underground Hydrogen Storage (UHS) in depleted oil and gas reservoirs could provide a cost-effective solution to balance seasonal fluctuations in renewable energy generation. However, data and knowledge on UHS at subsurface conditions are limited so it is difficult to estimate how effective this type of storage could be. In this study, we perform high pressure experiment to measure the effectiveness of cyclic hydrogen (H 2 ) storage in a specimen of Temblor sandstone retrieved from the San Joaquin Basin of California. Our experiment mimics reservoir pressure conditions to measure H 2 -brine relative permeability and fluid-rock interactions over the course of ten charging and discharging cycles. Initial gas breakthrough occurred at 15 % to 25 % H2 saturation in the specimen with 3 % NaCl brine as the resident fluid. Continuing injecting to 4 pore volumes (PV) of H 2 yielded an asymptotic H 2 saturation of 38 % to 41 %, a level often referred to as the irreducible gas saturation based on two-phase flow. The boundary condition in this study mimics the near wellbore region, which experiences bi-directional H 2 flow. This bi-directional flow led to evaporative drying of the specimen resulting in 94 % H 2 saturation at the end of 10th cycle. This indicates that cyclic flow and evaporative drying can lead to more efficient reservoir storage where a larger fraction of the reservoir porosity is usable to store H 2 . The produced gas stream consisted of H 2 mixed with 8 % to 22 % H 2 O, indicating formation dry-out by evaporation. Meanwhile, produced water chemistry indicated calcite and silicate dissolution, with calcite sourced from fossil fragments. This led to a loss of cementation and weakened the rock sample. Combined, our results indicate dry-out, compaction, increased H 2 saturation, rock weakening, and permeability loss during cyclic UHS. Overall, we anticipate that the combined effects should lead to higher than anticipated UHS storage efficiency per volume of sandstone reservoir rock.

08 HYDROGEN↗

Joint opening or hydroshearing? Analyzing a fracture zone stimulation at Fenton Hill

Here, we analyze a deep hydraulic stimulation of a fracture zone that was conducted as part of the classical Fenton Hill Hot Dry Rock Program in the 1970s. At the time, it was suggested that a pre-existing fracture or multiple fractures within the fracture zone were jacked open by injection-induced increase in pressure. In this study, we analyze the same stimulation experiment, but investigate the possibility of an alternative mechanism of shear reactivation of pre-existing fractures. We conduct modeling that accounts for both jacking (or elastic-fracture opening) and shear-slip dilation and demonstrate that injection-induced shear reactivation (or hydroshearing) could have occurred simultaneously with seismic events of magnitudes lower than what can be felt by humans. In fact, simulations considering shear reactivation seem to better match observed fluid recovery after multiple injection cycles. Shear reactivation and shear dilation results in locked-open fractures, especially near the injection well that provides permeability of higher flow recovery. We then investigate the sensitivity of the proposed model by varying some of the critical parameters such as maximum aperture, dilation angle, as well as fracture density. Interestingly, none of the simulated cases resulted in a large event that could have been felt by humans, but did result in a cumulative seismic magnitude of less than 1 for each given stimulation step. In conclusion, these results suggest that a permanent irreversible permeability increase of several orders of magnitude can be obtained by hydroshearing in a “seismically” safe manner.

58 GEOSCIENCES↗