Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA CONDUCTIVITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Vacuum arc plasma thrusters with inductive energy storage driver

An apparatus for producing a vacuum arc plasma source device using a low mass, compact inductive energy storage circuit powered by a low voltage DC supply acts as a vacuum arc plasma thruster. An inductor is charged through a switch, subsequently the switch is opened and a voltage spike of Ldi/dt is produced initiating plasma across a resistive path separating anode and cathode. The plasma is subsequently maintained by energy stored in the inductor. Plasma is produced from cathode material, which allows for any electrically conductive material to be used. A planar structure, a tubular structure, and a coaxial structure allow for consumption of cathode material feed and thereby long lifetime of the thruster for long durations of time.

Schein, Jochen↗

Young's Moduli of Cold and Vacuum Plasma Sprayed Metallic Coatings

Monolithic metallic copper alloy and NiCrAlY coatings were fabricated by either the cold spray (CS) or the vacuum plasma spray (VPS) deposition processes. Dynamic elastic modulus property measurements were conducted on these monolithic coating specimens between 300 K and 1273 K using the impulse excitation technique. The Young's moduli decreased almost linearly with increasing temperature at all temperatures except in the case of the CS Cu-23%Cr-5%Al and VPS NiCrAlY, where deviations from linearity were observed above a critical temperature. It was observed that the Young's moduli for VPS Cu-8%Cr were larger than literature data compiled for Cu. The addition of 1%Al to Cu- 8%Cr significantly increased its Young's modulus by 12 to 17% presumably due to a solid solution effect. Comparisons of the Young s moduli data between two different measurements on the same CS Cu- 23%Cr-5%Al specimen revealed that the values measured in the first run were about 10% higher than those in the second run. It is suggested that this observation is due to annealing of the initial cold work microstructure resulting form the cold spray deposition process.

Raj, S. V.↗

Survey of Propulsion Technologies Applicable to Cubesats

At present, no Cubesat has flown in space featuring propulsion. This was acceptable as long as CubeSats were flown mostly as university experiments. As CubeSats become of interest to other users in the government and industry communities as well, a larger range of capabilities may be required than exhibited so far, while maintaining the uniqueness of the Cubesat platform. Propulsion capability is crucial in increasing mission capabilities of future CubeSats, such as orbit change and raising, formation flying, proximity operations, fine attitude control, or drag-make-up and de-orbit. While some of these tasks may be accomplished with propellantless devices, their applications are limited, applicable mostly to a single task, and bear their own risks. In this study, a survey was conducted of propulsion technologies applicable to CubeSats. Only few off-the-shelf design solutions exist today. The survey was thus expanded to such devices as well that are under significant development, and are approaching the required design envelope for CubeSats with respect to mass, volume, and power. In some cases, such as electric propulsion devices, CubeSat architectures themselves may need to be adapted, required to feature deployable solar arrays to increase power capabilities. Given the vast scope of this survey, only thruster technologies could be surveyed. However, valves and other feed system components, as well as their integration, are equally important, but have to be left to a future survey. Three major propulsion technology areas applicable to CubeSats emerged when conducting this review: (1) Existing technologies, such as butane systems, pulsed plasma thrusters, and vacuum arc thrusters are applicable to CubeSats today with no or only minor changes, (2) New thruster technologies under significant development, such as hydrazine monopropellant systems, ion engines, or colloid thrusters could be adapted to CubeSats with some further development, especially also in other subsystem areas such as feed systems and power processing units. They will also require increased power capabilities, and (3) emerging technologies, such as micro electrospray arrays and micro cavity discharge arrays that offer even higher flexibility due to scalability for CubeSats, and enable compact integration.

micropropulsion↗

Delayed Development of Cool Plasmas in X-Ray Flares from the Young Sun-like Star κ1 Ceti

The Neutron star Interior Composition Explorer (NICER) X-ray observatory observed two powerful X-ray flares equivalent to superflares from the nearby young solar-like star κ 1 Ceti in 2019. NICER follows each flare from the onset through the early decay, collecting over 30 counts s −1 near the peak, enabling a detailed spectral variation study of the flare rise. The flare in September varies quickly in ∼800 s, while the flare in December has a few times longer timescale. In both flares, the hard-band (2–4 keV) light curves show typical stellar X-ray flare variations with a rapid rise and slow decay, while the soft X-ray light curves, especially of the September flare, have prolonged flat peaks. The time-resolved spectra require two temperature plasma components at kT ∼0.3–1 and ∼2–4 keV. Both components vary similarly, but the cool component lags by ∼200 s with a four to six times smaller emission measure (EM) compared to the hot component. A comparison with hydrodynamic flare loop simulations indicates that the cool component originates from X-ray plasma near the magnetic loop footpoints that mainly cools via thermal conduction. The time lag represents the travel time of the evaporated gas through the entire flare loop. The cool component has a several times smaller EM than its simulated counterpart, suggesting a suppression of conductive cooling, possibly by the expansion of the loop cross-sectional area or turbulent fluctuations. The cool component's time lag and EM ratio provide important constraints on the flare loop geometry.

main sequence stars↗

Converging towards atomic and nuclear pressures (Final Report)

his report details the development of transformational tools and techniques, allowing the accurate characterization of matter at the most extreme conditions yet studied in the high energy density (HED) domain. Before this work, most experiments quantitatively mapping the nature of matter in the HED realm were performed using planar geometry, which allows for the isolation and measurement of variables in a single thermodynamic state. Such measurements include equation of state variables, optical conductivity, heat transport and more. However, due to a variety of plasma processes, such experiments are limited to below ~10 TPa (100 Mbar) pressures. To achieve higher pressures, convergent experiments are needed. Historically, convergent experiments have not been used for benchmark data because they are integral measurements. That is each part of a convergent target undergoes a time dependent wide range of states, making it difficult to accurately isolate any particular quantity for a given thermodynamic state. This effort developed innovative convergent HED platforms and techniques enabling the exploration of matter from atomic to nuclear scale pressures. This effort also performed pioneering experiments that yielded the first rigorous benchmark data at these extreme conditions. This funding award began with the overarching goal to understand the behavior of matter at extreme (atomic-to-nuclear scale) pressures. The motivation for these goals lie in the fact that every time scientists explore matter beyond the threshold of an atomic unit, there is a fundamental shift in science. The atomic unit for energy, mass, charge, length, and time have each been explored, and each time such a threshold was crossed, a new sequence of discoveries was made resulting in significant awards such as the Nobel Prize. The only unexplored atomic unit is pressure, and this effort set the course for exploring matter at and beyond such pressures. That most of the recently discovered extrasolar planets and stars, as well as matter in the late implosion stages of inertial fusion targets, have deep internal pressures at and beyond atomic pressures amplifies the importance of this effort. Much of the initial work in developing techniques to create these atomic-to-nuclear pressures already existed within the HED community, predominantly at large scale laser facilities such as the National Ignition Facility (NIF) and the Omega60 laser the University of Rochester and although these experiments were routinely performed the ability to extract information about the underlying physical states and processes remained elusive due to the complexity of the experiments, extreme scales in both time and space, and the integrated nature of all the measurements. This work built a rigorous framework so such measurements can routinely be made. This was done in part through the introduction of Bayesian inference techniques into the field of HED science. These techniques allow for the self-consistent extraction of the relevant variables and their explicit and implicit correlations, so as to make use of integrated experimental data to constrain physical models and provide accurate uncertainty bounds for the data. The techniques developed here are fully transparent and proved immediately useful providing quantitative rigorous benchmarks for physical states and processes at some of the most extreme conditions yet explored on Earth. This funding is directly or partly responsible for 7 publications in major peer-reviewed scientific journals, a doctoral thesis, 3 invited talks at major conferences, and the training of a post-doc, 2 graduate students, and 1 undergraduate student. Beyond the effort supported by this award launched the introduction of Bayesian inference into the HED physics community and helped push the usage if modern data-science techniques within the physics community at large.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interactions of magnetized plasma flows in pulsed-power driven experiments

A supersonic flow of magnetized plasma is produced by the application of a 1 MA-peak, 500 ns current pulse to a cylindrical arrangement of parallel wires, known as an inverse wire array. The plasma flow is produced by the J x B acceleration of the ablated wire material, and a magnetic field of several Tesla is embedded at source by the driving current. This setup has been used for a variety of experiments investigating the interactions of magnetized plasma flows. In experiments designed to investigate magnetic reconnection, the collision of counter-streaming flows, carrying oppositely directed magnetic fields, leads to the formation of a reconnection layer in which we observe ions reaching temperatures much greater than predicted by classical heating mechanisms. The breakup of this layer under the plasmoid instability is dependent on the properties of the inflowing plasma, which can be controlled by the choice of the wire array material. In other experiments, magnetized shocks were formed by placing obstacles in the path of the magnetized plasma flow. The pile-up of magnetic flux in front of a conducting obstacle produces a magnetic precursor acting on upstream electrons at the distance of the ion inertial length. This precursor subsequently develops into a steep density transition via ion-electron fluid decoupling. Obstacles which possess a strong private magnetic field affect the upstream flow over a much greater distance, providing an extended bow shock structure. In the region surrounding the obstacle the magnetic pressure holds off the flow, forming a void of plasma material, analogous to the magnetopause around planetary bodies with self-generated magnetic fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ion Collection by a Sphere in a Drifting Collisional Plasma

SCEPTIC3D now includes charge-exchange collisions, and is used to examine ion collection by a floating conducting sphere (small compared to the electron debye length) in the presence of a background neutral drift. The enhancement of ion collection at moderate collisionalities seen for the stationary case is weakened as the drift speed increases from the ion thermal speed to the ion sound speed, above which no enhancement is seen.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interactions of magnetized plasma flows in pulsed-power driven experiments

A supersonic flow of magnetized plasma is produced by the application of a 1 MA-peak, 500 ns current pulse to a cylindrical arrangement of parallel wires, known as an inverse wire array. The plasma flow is produced by the J x B acceleration of the ablated wire material, and a magnetic field of several Tesla is embedded at source by the driving current. This setup has been used for a variety of experiments investigating the interactions of magnetized plasma flows. In experiments designed to investigate magnetic reconnection, the collision of counter-streaming flows, carrying oppositely directed magnetic fields, leads to the formation of a reconnection layer in which we observe ions reaching temperatures much greater than predicted by classical heating mechanisms. The breakup of this layer under the plasmoid instability is dependent on the properties of the inflowing plasma, which can be controlled by the choice of the wire array material. In other experiments, magnetized shocks were formed by placing obstacles in the path of the magnetized plasma flow. The pile-up of magnetic flux in front of a conducting obstacle produces a magnetic precursor acting on upstream electrons at the distance of the ion inertial length. This precursor subsequently develops into a steep density transition via ion-electron fluid decoupling. Obstacles which possess a strong private magnetic field affect the upstream flow over a much greater distance, providing an extended bow shock structure. Finally, in the region surrounding the obstacle the magnetic pressure holds off the flow, forming a void of plasma material, analogous to the magnetopause around planetary bodies with self-generated magnetic fields.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Structure and electronic properties features of amorphous chalhogenide semiconductor films prepared by ion-plasma spraying

Structure of amorphous chalcogenide semiconductor glassy As-S-Se films, obtained by high-frequency (HF) ion-plasma sputtering has been investigated. It was shown that the length of the atomic structure medium order and local structure were different from the films obtained by thermal vacuum evaporation. Temperature dependence of dark conductivity, as well as the dependence of the spectral transmittance has been studied. Conductivity value was determined at room temperature. Energy activation conductivity and films optical band gap have been calculated. Temperature and field dependence of the drift mobility of charge carriers in the HF As-S-Se films have been shown. Bipolarity of charge carriers drift mobility has been confirmed. Absence of deep traps for electrons in the As{sub 40}Se{sub 30}S{sub 30} spectrum of localized states for films obtained by HF plasma ion sputtering was determined. Bipolar drift of charge carriers was found in amorphous As{sub 40}Se{sub 30}S{sub 30} films obtained by ion-plasma sputtering of high-frequency, unlike the films of these materials obtained by thermal evaporation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Toward quasi-DC conductivity of warm dense matter measured by single-shot terahertz spectroscopy

Here, we present an experimental setup capable of measuring the near DC conductivity of laser generated warm dense matter using single-shot terahertz time-domain spectroscopy. The setup uses a reflective echelon and balanced detection to record THz waveforms with a minimum detectable signal of 0.2% in a single laser pulse. We describe details of the experimental setup and the data analysis procedure and present single-shot terahertz transmission data on aluminum that has been laser heated to an electron temperature of 0.5 eV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation study of interactions of Space Shuttle-generated electron beams with ambient plasmas

This report summarizes results obtained through the support of NASA Grant NAGW-1936. The objective of this report is to conduct large scale simulations of electron beams injected into space. The topics covered include the following: (1) simulation of radial expansion of an injected electron beam; (2) simulations of the active injections of electron beams; (3) parameter study of electron beam injection into an ionospheric plasma; and (4) magnetosheath-ionospheric plasma interactions in the cusp.

Lin, Chin S.↗

Robust Low Cost Liquid Rocket Combustion Chamber by Advanced Vacuum Plasma Process

Next-generation, regeneratively cooled rocket engines will require materials that can withstand high temperatures while retaining high thermal conductivity. Fabrication techniques must be cost efficient so that engine components can be manufactured within the constraints of shrinking budgets. Three technologies have been combined to produce an advanced liquid rocket engine combustion chamber at NASA-Marshall Space Flight Center (MSFC) using relatively low-cost, vacuum-plasma-spray (VPS) techniques. Copper alloy NARloy-Z was replaced with a new high performance Cu-8Cr-4Nb alloy developed by NASA-Glenn Research Center (GRC), which possesses excellent high-temperature strength, creep resistance, and low cycle fatigue behavior combined with exceptional thermal stability. Functional gradient technology, developed building composite cartridges for space furnaces was incorporated to add oxidation resistant and thermal barrier coatings as an integral part of the hot wall of the liner during the VPS process. NiCrAlY, utilized to produce durable protective coating for the space shuttle high pressure fuel turbopump (BPFTP) turbine blades, was used as the functional gradient material coating (FGM). The FGM not only serves as a protection from oxidation or blanching, the main cause of engine failure, but also serves as a thermal barrier because of its lower thermal conductivity, reducing the temperature of the combustion liner 200 F, from 1000 F to 800 F producing longer life. The objective of this program was to develop and demonstrate the technology to fabricate high-performance, robust, inexpensive combustion chambers for advanced propulsion systems (such as Lockheed-Martin's VentureStar and NASA's Reusable Launch Vehicle, RLV) using the low-cost VPS process. VPS formed combustion chamber test articles have been formed with the FGM hot wall built in and hot fire tested, demonstrating for the first time a coating that will remain intact through the hot firing test, and with no apparent wear. Material physical properties and the hot firing tests are reviewed.

Holmes, Richard↗

Nanocoatings for High-Efficiency Industrial and Tooling Systems

This industry-driven project was the result of a successful response by Eaton Corporation to a DOE/ITP Program industry call. It consisted of three phases in which ORNL participated. In addition to Eaton Corporation and ORNL (CRADA), the project team included Ames Laboratory, who developed the underlying concept for aluminum-magnesium-boron based nanocomposite coatings [1], and Greenleaf, a small tooling manufacturer in western Pennsylvania. This report focuses on the portion of this work that was conducted by ORNL in a CRADA with Eaton Corporation. A comprehensive final report for the entire effort, which ended in September 2010, has been prepared by Eaton Corporation. Phase I, “Proof of Concept” ran for one year (September 1, 2006 to September 30, 2007) during which the applicability of AlMgB14 single-phase and nanocomposite coatings on hydraulic material coupons and components as well as on tool inserts was demonstrated.. The coating processes used either plasma laser deposition (PLD) or physical vapor deposition (PVD). During Phase I, ORNL conducted laboratory-scale pin-on-disk and reciprocating pin-on-flat tests of coatings produced by PLD and PVD. Non-coated M2 tool steel was used as a baseline for comparison, and the material for the sliding counterface was Type 52100 bearing steel since it simulated the pump materials. Initial tests were run mainly in a commercial hydraulic fluid named Mobil DTE-24, but some tests were later run in a water-glycol mixture as well. A tribosystem analysis was conducted to define the operating conditions of pump components and to help develop simulative tests in Phase II. Phase II, “Coating Process Scale-up” was intended to use scaled-up process to generate prototype parts. This involved both PLD practices at Ames Lab, and a PVD scale-up study at Eaton using its production capable equipment. There was also a limited scale-up study at Greenleaf for the tooling application. ORNL continued to conduct friction and wear tests on process variants and developed tests to better simulate the applications of interest. ORNL also employed existing lubrication models to better understand hydraulic pump frictional behavior and test results. Phase III, “Functional Testing” focused on finalizing the strategy for commercialization of AlMgB14 coatings for both hydraulic and tooling systems. ORNL continued to provide tribology testing and analysis support for hydraulic pump applications. It included both laboratory-scale coupon testing and the analysis of friction and wear data from full component-level tests performed at Eaton Corp. Laboratory-scale tribology test methods are used to characterize the behavior of nanocomposite coatings prior to running them in full-sized hydraulic pumps. This task also includes developing tribosystems analyses, both to provide a better understanding of the performance of coated surfaces in alternate hydraulic fluids, and to help design useful laboratory protocols. Analysis also includes modeling the lubrication conditions and identifying the physical processes by which wear and friction of the contact interface changes over time. This final report summarizes ORNL’s portion of the nanocomposite coatings development effort and presents both generated data and the analyses that were used in the course of this effort.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Solar wind heat flow

The ability of a theoretical solar wind model to predict the energy flux density due to heat conduction was investigated. In order to demonstrate this capability, the analysis used simultaneous data from the electron plasma experiment of Ogilvie and Lind, and the vector magnetic field data of Heppner and Sugiura on OGO-5. On the strength of two independent, different, and consistent experimental determinations of the conduction of heat flux by electrons at 149.6 gigameters(1 AU), it was determined that the models for the solar wind must be able to predict a value for the heat conduction in the range 0.007 to 0.008 in order to be in agreement with the observations.

Scudder, J.↗

Effect of cesium assistance on the electrical and structural properties of indium tin oxide films grown by magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by cesium (Cs)-assisted dc magnetron sputtering in an attempt to achieve a high performance at low temperatures. The films were deposited on SiO{sub 2}/Si wafer and glass (Eagle 2000) substrates at a substrate temperature of 100 degree sign C with a Cs vapor flow during the deposition process. The ITO thin films deposited in the presence of Cs vapor showed better crystallinity than the control films grown under normal Ar/O{sub 2} plasma conditions. The resistivity of the films with the Cs assistance was lower than that of the control films. The lowest resistivity of 6.2x10{sup -4} {Omega} cm, which is {approx}20% lower than that of the control sample, was obtained without any postdeposition thermal annealing. The surface roughness increased slightly when Cs vapor was added. The optical transmittance was >80% at wavelengths ranging from 380 to 700 nm.

36 MATERIALS SCIENCE↗

Plasma Current Start-up Experiment using Waves in the Lower Hybrid Frequency Range in TST-2

Noninductive plasma current (I{sub p}) start-up experiments using RF power in the lower hybrid frequency range are being conducted on the TST-2 spherical tokamak. The lower hybrid wave (LHW) has demonstrated efficient current drive in conventional tokamaks. However, in spherical tokamak (ST) plasmas with very high dielectric constants (;{epsilon}{approx}{omega}{sub pe}{sup 2}/{Omega}{sub e}{sup 2}>>1), accessibility of the LHW to the plasma core is severely limited. Our approach is to keep the plasma density low (such that {epsilon}{approx}1) during I{sub p} ramp-up. Once I{sub p} reaches a level sufficiently high for neutral beam current drive, plasma can be densified and transformed into an advanced tokamak plasma dominated by the self-driven bootstrap current. Initial plasma start-up experiments were performed on TST-2 using a combline antenna which excites a traveling fast wave. After formation of toroidal flux surfaces, RF power and vertical field were ramped up to increase I{sub p}. Up to 12 kA of Ip has been obtained by this method. Soft X-ray measurements indicate that the electron temperature increases as I{sub p} increases, and hard X-ray spectroscopy indicates that energetic electrons build up as I{sub p} is ramped up.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

PIC simulation of electrodeless plasma thruster with rotating electric field

For longer lifetime of electric propulsion system, an electrodeless plasma thruster with rotating electric field have been proposed utilizing a helicon plasma source. The rotating electric field may produce so-called Lissajous acceleration of helicon plasma in the presence of diverging magnetic field through a complicated mechanism originating from many parameters. Two-dimensional simulations of the Lissajous acceleration were conducted by a code based on Particle-In-Cell (PIC) method and Monte Carlo Collision (MCC) method for understanding plasma motion in acceleration area and for finding the optimal condition. Obtained results show that azimuthal current depends on ratio of electron drift radius to plasma region length, AC frequency, and axial magnetic field. When ratio of cyclotron frequency to the AC frequency is higher than unity, reduction of the azimuthal current by collision effect is little or nothing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Impact of first-principles properties of deuterium–tritium on inertial confinement fusion target designs

A comprehensive knowledge of the properties of high-energy-density plasmas is crucial to understanding and designing low-adiabat, inertial confinement fusion (ICF) implosions through hydrodynamic simulations. Warm-dense-matter (WDM) conditions are routinely accessed by low-adiabat ICF implosions, in which strong coupling and electron degeneracy often play an important role in determining the properties of warm dense plasmas. The WDM properties of deuterium–tritium (DT) mixtures and ablator materials, such as the equation of state, thermal conductivity, opacity, and stopping power, were usually estimated by models in hydro-codes used for ICF simulations. In these models, many-body and quantum effects were only approximately taken into account in the WMD regime. Moreover, the self-consistency among these models was often missing. To examine the accuracy of these models, we have systematically calculated the static, transport, and optical properties of warm dense DT plasmas, using first-principles (FP) methods over a wide range of densities and temperatures that cover the ICF “path” to ignition. These FP methods include the path-integral Monte Carlo (PIMC) and quantum-molecular dynamics (QMD) simulations, which treat electrons with many-body quantum theory. The first-principles equation-of-state table, thermal conductivities (κ{sub QMD}), and first principles opacity table of DT have been self-consistently derived from the combined PIMC and QMD calculations. They have been compared with the typical models, and their effects to ICF simulations have been separately examined in previous publications. In this paper, we focus on their combined effects to ICF implosions through hydro-simulations using these FP-based properties of DT in comparison with the usual model simulations. We found that the predictions of ICF neutron yield could change by up to a factor of ∼2.5; the lower the adiabat of DT capsules, the more variations in hydro-simulations. The FP-based properties of DT are essential for designing ICF ignition targets. Future work on first-principles studies of ICF ablator materials is also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗