Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOADING RATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study, volume 1

An active controls technology (ACT) system architecture was selected based on current technology system elements and optimal control theory was evaluated for use in analyzing and synthesizing ACT multiple control laws. The system selected employs three redundant computers to implement all of the ACT functions, four redundant smaller computers to implement the crucial pitch-augmented stability function, and a separate maintenance and display computer. The reliability objective of probability of crucial function failure of less than 1 x 10 to the -9th power per flight of 1 hr can be met with current technology system components, if the software is assumed fault free and coverage approaching 1.0 can be provided. The optimal control theory approach to ACT control law synthesis yielded comparable control law performance much more systematically and directly than the classical s-domain approach. The ACT control law performance, although somewhat degraded by the inclusion of representative nonlinearities, remained quite effective. Certain high-frequency gust-load alleviation functions may require increased surface rate capability.

Hanks, G. W.↗

Effect of water vapor on fatigue crack growth in 7475-T651 aluminum alloy plate

The effects of water vapor on fatigue crack growth in 7475-T651 aluminum alloy plate at frequencies of 1 Hz and 10 Hz were investigated. Twenty-five mm thick compact specimens were subjected to constant amplitude fatigue testing at a load ratio of 0.2. Fatigue crack growth rates were calculated from effective crack lengths determined using a compliance method. Tests were conducted in hard vacuum and at water vapor partial pressures ranging from 94 Pa to 3.8 kPa. Fatigue crack growth rates were frequency insensitive under all environment conditions tested. For constant stress intensity factor ranges crack growth rate transitions occurred at low and high water vapor pressures. Crack growth rates at intermediate pressures were relatively constant and showed reasonable agreement with published data for two Al-Cu-Mg alloys. The existence of two crack growth rate transitions suggests either a change in rate controlling kinetics or a change in corrosion fatigue mechanism as a function of water vapor pressure. Reduced residual deformation and transverse cracking specimens tested in water vapor versus vacuum may be evidence of embrittlement within the plastic zone due to environmental interaction.

Dicus, D. L.↗

Constitutive modeling for isotropic materials (HOST)

This report presents the results of the second year of work on a problem which is part of the NASA HOST Program. Its goals are: (1) to develop and validate unified constitutive models for isotropic materials, and (2) to demonstrate their usefulness for structural analyses of hot section components of gas turbine engines. The unified models selected for development and evaluation are that of Bodner-Partom and Walker. For model evaluation purposes, a large constitutive data base is generated for a B1900 + Hf alloy by performing uniaxial tensile, creep, cyclic, stress relation, and thermomechanical fatigue (TMF) tests as well as biaxial (tension/torsion) tests under proportional and nonproportional loading over a wide range of strain rates and temperatures. Systematic approaches for evaluating material constants from a small subset of the data base are developed. Correlations of the uniaxial and biaxial tests data with the theories of Bodner-Partom and Walker are performed to establish the accuracy, range of applicability, and integability of the models. Both models are implemented in the MARC finite element computer code and used for TMF analyses. Benchmark notch round experiments are conducted and the results compared with finite-element analyses using the MARC code and the Walker model.

Lindholm, U. S.↗

Electromagnetic braking for Mars spacecraft

Aerobraking concepts are being studied to improve performance and cost effectiveness of propulsion systems for Mars landers and Mars interplanetary spacecraft. Access to megawatt power levels (nuclear power coupled to high-storage inductive or capacitive devices) on a manned Mars interplanetary spacecraft may make feasible electromagnetic braking and lift modulation techniques which were previously impractical. Using pulsed microwave and magnetic field technology, potential plasmadynamic braking and hydromagnetic lift modulation techniques have been identified. Entry corridor modulation to reduce loads and heating, to reduce vertical descent rates, and to expand horizontal and lateral landing ranges are possible benefits. In-depth studies are needed to identify specific design concepts for feasibility assessments. Standing wave/plasma sheath interaction techniques appear to be promising. The techniques may require some tailoring of spacecraft external structures and materials. In addition, rapid response guidance and control systems may require the use of structurally embedded sensors coupled to expert systems or to artificial intelligence systems.

Holt, A. C.↗

Prediction of service life of aircraft structural components using the half-cycle method

The service life of aircraft structural components undergoing random stress cycling was analyzed by the application of fracture mechanics. The initial crack sizes at the critical stress points for the fatigue-crack growth analysis were established through proof load tests. The fatigue-crack growth rates for random stress cycles were calculated using the half-cycle method. A new equation was developed for calculating the number of remaining flights for the structural components. The number of remaining flights predicted by the new equation is much lower than that predicted by the conventional equation.

Ko, William L.↗

How gravity and joint scaling affect dynamics response

If a scale model of a space structure is ground tested to establish dynamic characteristics of full-scale space structure, two factors need to be taken into consideration: the joint tolerances may not be scaled, and joint preloads (from gravity) may be present. In some situations, these differences may significantly affect dynamic response so that the model is not representative of the structure in space. In this study, joint effects are investigated by considering the response of a single-degree-of-freedom system that is restrained by a joint linkage. The joint is characterized by its initial stiffness, the load at which it slips, its hardening rate, and the distance it can slip (joint 'slop' or gap). The steady-state response of the system is calculated using a harmonic balance approach. It is found that the system response is multivalued for certain ranges of gap dimensions. When this is the case, small changes in system properties can lead to large differences in dynamic response and make it difficult to obtain meaningful results directly from model testing.

Hsu, S. T.↗

Computational simulation of structural fracture in fiber composites

A methodology was developed for the computational simulation of structural fracture in fiber composites. This methodology consists of step-by-step procedures for mixed-mode fracture in generic components and an integrated computer code, Composite Durability Structural Analysis (CODSTRAN). The generic types of composite structural fracture include: (1) single and combined mode fracture in beams; 2) laminate free-edge delamination fracture; and (3) laminate center flaw progressive fracture. Structural fracture is identified by rapid changes in one or all of the following: (1) displacements, (2) frequencies, (3) the buckling loads, or (4) the strain energy release rate. These rapid changes are herein assumed to denote imminent structural fracture. Based on these rapid changes, parameters are identified which can be used as guidelines for structural fracture, inspection intervals and retirement for cause.

Chamis, Christos C.↗

Experimental observations and finite element analysis of the initiation of fiber microbuckling in notched composite laminates

An understanding was developed of the factors that determine the semi-circular edge-notched compressive strength and the associated failure mode(s) were identified of thermoplastic composite laminates with multidirectional stacking sequences. The experimental observations and the detailed literature review suggest at least four factors that affected the determination of the strain levels at which fiber microbuckling initiates and thus, partially control the composite's compression strength. The dependent variables studied are the compressive strength of a reduced gage section compression specimen and the compression strength of a compression specimen with two semi-circular edge notches (no opposite free edges) centered along the gage section. In this research, specimens containing two semi-circular edge notches (no opposite free edges) were loaded in compression at a relatively slow rate to provide more stable development of fiber microbuckling damage. The results indicate that the local constraints (free surfaces, supporting ply orientation, and resin-rich regions) significantly affect the strain level for the initiation of in-plane fiber microbuckling. Preliminary results at an elevated temperature, 77 C, showed the shear stress yield strength of the resin was reduced and consequently, the resistance to fiber microbuckling was also reduced. The finite element analysis of the perfectly straight fiber problem indicates that the free surface effect causes a 10 percent reduction in the critical buckling strain. However, the experimentally measured reduction for fibers with an initial fiber curvature, was 35 percent.

Guynn, E. Gail↗

The viscoplastic behavior of Hastelloy-X single crystal

A viscoplastic constitutive model for simulating the behavior of Hastelloy-X single crystal material was derived based on crystallographic slip theory. To determine the appropriate constitutive model constants and to test the predictions of the model, tests on Hastelloy-X crystals were carried out, including the rate sensitivity, cyclic hardening, nonproportional hardening, relaxation, and strain rate dip tests. It was found necessary to include cube slip in the model in order to correlate the uniaxial behavior of the single crystal, to incorporate the interaction effects in both the hardening and the dynamic recovery evolution equations for the drag stress, and to successfully capture correct strain rate sensitivity under biaxial tension-torsion loading conditions.

Jordan, Eric H.↗

Finite element analysis of the Space Shuttle Main Engine (SSME) alternate turbopump development (ATD) high pressure oxydizer turbopump (HPOTP)

A 3D model of all stationary components of the ATD HPOTP is analyzed using a superelement solution technique to obtain a better understanding of the pump behavior and to support pump testing. Emphasis is place on the methods used for determining deflections. As part of the model verification, analyses were conducted on the main housing model under proof-pressure and push-test loading conditions. The analysis at 109 percent rate power level resulted in asymmetric deformation patterns which were used to calculate operating and rub clearances. The present analysis is considered to provide the most realistic representation of the ATD HPOTP to date.

Ham-Battista, G. L.↗

A warning concerning the take-off with heavy load

A successful take-off can be made with an airplane so heavily loaded that it cannot climb to a height greater than the span of its wings. The explanation is that the power required to maintain level flight at an altitude of the order of the wing span may be as much as 50 per cent greater than that necessary when the airplane is just clear of the ground. The failure of heavily loaded airplanes to continue climbing at the rate attained immediately after the actual take-off is a grave hazard and has resulted in great risk or catastrophe in three notable cases which are cited.

Reid, Elliott G↗

A complex reaction time study (Sternberg) in space flight

Simple and complex (Sternberg) reaction time studies were flown on three and seven day Shuttle flights in 1985. Three subjects did selftesting with an onboard handheld calculator without difficulty. There was little change in simple reaction time. One subject demonstrated a decrease in the processing rate during space motion sickness while a second exhibited an increase in complex reaction time without a change in processing rate during a period of high work load. The population was too small to demonstrate significant changes. This study demonstrates the ease and practicality of such measurements and indicates the potential value of such studies in space.

Thornton, W.↗

High temperature brush seal tuft testing of metallic bristles versus chrome carbide

The tribology of brush seals is of considerable interest to turbine engine designers because bristle wear continues to limit long term seal performance and life. To provide better materials characterization and foster the development of improved seals, NASA Lewis has developed a brush seal tuft tester. In this test, a 'paintbrush' sample tuft is loaded under constant contact pressure against the outside diameter of a rotating journal. With this configuration a direct measurement of load and friction is made. Accurate wear rate measurements are possible due to the known contact pressure. Previously reported baseline research using this facility showed good data repeatability and wear morphology similar to published seal data. This paper extends and expands the database for candidate brush seal materials. A series of tuft tests were completed to evaluate the performance of five high temperature superalloy wires sliding against plasma sprayed nichrome-bonded chrome carbide. Wire materials were either nickel-chrome or cobalt-chrome based superalloys. Good corroboration of the tuft results with dynamic seal rig tests was observed; giving additional confidence in the tuft test as a screening and development tool.

Fellenstein, James A.↗

Elevated Temperature Deformation of Cr3Si Alloyed with Mo

Four-point bend, constant load compressive creep and constant engineering strain rate tests were conducted on arc-melted and powder-metallurgy (PM) processed Cr40Mo30Si30 specimens in the temperature range 1400 and 1700 K. This is a two phase alloy consisting of (CrMo)3Si and (Cr,Mo)5Si3 phases. The PM specimens, which were substantially weaker than the arc-melted materials, exhibited a stress exponent n, of about 2 and an apparent activation energy for creep, Q(sub 3), of 485 kJ/mol. The mechanism in these specimens appeared to be controlled by creep of a glassy phase. In the case of arc-melted specimens for which nis approximately 3 and Q(sub 3) is approximately 430 kJ/mol, the rate-controlling creep mechanism appeared to be that dominant in the (Cr,Mo)5Si3 phase. In this case, it is suggested that the Nabarro creep mechanism, where dislocation climb is controlled by Bardeen-Herring vacancy sources, is the dominant creep mechanism. Finally, an analysis of the present and literature data on Cr3Si alloyed with Mo appeared to suggest that the creep rate decreases sharply with an increase in the Mo/Si ratio.

Raj, S. V.↗

NASA Task Load Index (TLX): Paper and Pencil Package - Volume 1.0

This booklet contains the materials necessary to collect subjective workload assessments with the NASA Task Load Index. This procedure for collecting workload ratings was developed by the Human Performance Group at NASA Ames Research Center during a three year research effort that involved more than 40 laboratory. simulation. and inflight experiments. Although the technique is still undergoing evaluation. this booklet is being distributed to allow other researchers to use it in their own experiments. Comments or suggestions about the procedure would be greatly appreciated. This package is intended to fill a "nuts and bolts" function of describing the procedure. A bibliography provides background information about previous empirical findings and the logic that supports the procedure.

Hart, Sandra G.↗

Creep-Fatigue Interaction Testing

Fatigue fives in metals are nominally time independent below 0.5 T(sub Melt). At higher temperatures, fatigue lives are altered due to time-dependent, thermally activated creep. Conversely, creep rates are altered by super. imposed fatigue loading. Creep and fatigue generally interact synergistically to reduce material lifetime. Their interaction, therefore, is of importance to structural durability of high-temperature structures such as nuclear reactors, reusable rocket engines, gas turbine engines, terrestrial steam turbines, pressure vessel and piping components, casting dies, molds for plastics, and pollution control devices. Safety and lifecycle costs force designers to quantify these interactions. Analytical and experimental approaches to creep-fatigue began in the era following World War II. In this article experimental and life prediction approaches are reviewed for assessing creep-fatigue interactions of metallic materials. Mechanistic models are also discussed briefly.

Halford, Gary R.↗

On Europa's Magnetospheric Interaction: A MHD Simulation of the E4 Flyby

The global three-dimensional interaction of Europa with the Jovian magnetosphere is modeled by using a complete set of ideal magnetohydrodynamic (MHD) equations. The model accounts for exospheric mass loading, ion-neutral charge exchange, recombination, and a possible intrinsic dipole magnetic field of Europa. The single-fluid MHD equations are solved by using a modem, finite volume, higher-order, Godunov-type method on an adoptively refined unstructured grid, which allows detailed modeling of the region near Europa while still resolving both the upstream region and the satellite's wake. The magnetic field and plasma density measured during Galileo's EGA flyby of December 19, 1996, are reproduced reasonably well in the simulation. We find the agreement between the data and our model particularly convincing if we assume that the plasma velocity during the EGA flyby deviated from the nominal corotation direction by approximately 20 deg. Evidence from the Galileo energetic particle detector also supports this assumption. In this case, we can fit the data using a dipole with orientation close to that of an induced dipole arising from the interaction of a hypothetical conducting subsurface layer on Europa with the periodically changing magnetic field of Jupiter. However, the magnitude of the dipole in our model is somewhat smaller (70%) than that suggested by Khurana et al. The total mass loading and ion-neutral charge exchange rates are consistent with the estimates of Europa's atmosphere and ionosphere.

Kabin, K.↗

Test Rig for Evaluating Active Turbine Blade Tip Clearance Control Concepts

Improved blade tip sealing in the high pressure compressor and high pressure turbine can provide dramatic improvements in specific fuel consumption, time-on-wing, compressor stall margin and engine efficiency as well as increased payload and mission range capabilities of both military and commercial gas turbine engines. The preliminary design of a mechanically actuated active clearance control (ACC) system for turbine blade tip clearance management is presented along with the design of a bench top test rig in which the system is to be evaluated. The ACC system utilizes mechanically actuated seal carrier segments and clearance measurement feedback to provide fast and precise active clearance control throughout engine operation. The purpose of this active clearance control system is to improve upon current case cooling methods. These systems have relatively slow response and do not use clearance measurement, thereby forcing cold build clearances to set the minimum clearances at extreme operating conditions (e.g., takeoff, re-burst) and not allowing cruise clearances to be minimized due to the possibility of throttle transients (e.g., step change in altitude). The active turbine blade tip clearance control system design presented herein will be evaluated to ensure that proper response and positional accuracy is achievable under simulated high-pressure turbine conditions. The test rig will simulate proper seal carrier pressure and temperature loading as well as the magnitudes and rates of blade tip clearance changes of an actual gas turbine engine. The results of these evaluations will be presented in future works.

Lattime, Scott B.↗