Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HIGH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Gel based sulfur cathodes with a high sulfur content and large mass loading for high-performance lithium–sulfur batteries

A significantly improved conductive matrix design for the sulfur electrode is essential to solve several problems related to sulfur electrochemistry toward the development of practical lithium–sulfur batteries (LSBs). Great progress has been made by using a variety of carbon-based nanostructures for physically and chemically confining soluble polysulfides as well as providing conductive paths. However, most of these electrode designs have a low sulfur content or a low sulfur loading, leading to a low specific capacity or low areal capacity at the electrode level. Herein, intrinsically N- and O-doped carbon nanoribbon (CNR) aerogels, obtained by pyrolysis of bacterial cellulose (BC) aerogels, were employed to form gel-based sulfur cathodes, simultaneously achieving both a high sulfur content and a high sulfur loading. With a sulfur loading of 6.4 mg cm−2 and a sulfur content of 90% at the whole electrode (including the current collector) level, a capacity as high as 943 mA h g−1 was achieved, which corresponds to an areal capacity of 5.9 mA h cm−2. The outstanding cell performance is attributed to the gel based cathode structure, which can strongly hold a large amount of the catholyte and relieve the shuttle effect of lithium polysulfides.

Li, Shiqi↗

Oxidatively stable fluorinated sulfone electrolytes for high voltage high energy lithium-ion batteries

New fluorinated sulfones were synthesized and evaluated in high voltage lithium-ion batteries using LiNi 0.5 Mn 1.5 O 4 (LNMO) cathode. Fluorinated sulfones with an α-trifluoromethyl group exhibit enhanced oxidation stability, reduced viscosity and superior separator wettability as compared to their non-fluorinated counterparts. Finally, the improved performance in high voltage cells makes it a promising high voltage electrolyte for 5-V lithium-ion chemistry.

25 ENERGY STORAGE↗

Perovskite-sensitized β-Ga 2 O 3 nanorod arrays for highly selective and sensitive NO 2 detection at high temperature

Amongst various gaseous pollutants, NO 2 is one of the major exhausts originating from fossil fuel and gas combustions in vehicle engines and power plants at high temperature. Under such a scenario, in situ and real-time gas detection and monitoring solutions are largely limited, which hinders the energy-efficient and resource-saving operations of these advanced energy systems. Herein, a new type of perovskite-sensitized β-Ga 2 O 3 nanorod-array has been successfully fabricated to detect NO x at high temperature selectively and sensitively. The demonstrated gas sensors are highly sensitive to NO 2 at 800 °C, with excellent reversible and reproducible response characteristics. Through the surface decoration of perovskite-type La 0.8 Sr 0.2 CoO 3 (LSCO) nanoparticles, the sensitivity of β-Ga 2 O 3 nanorod array gas sensors is enhanced by nearly an order of magnitude, along with much faster response dynamics. A remarkable selectivity toward oxidative gases was also demonstrated with the robust differentiation of NO 2 .

36 MATERIALS SCIENCE↗

Sub-nanograin metal based high efficiency multilayer reflective optics for high energies

The present finding illuminates the physics of the formation of interfaces of metal based hetero-structures near layer continuous limit as an approach to develop high-efficiency W/B 4 C multilayer (ML) optics with ML periodicity varying d = 1.86–1.23 nm at a fixed number of layer pairs N = 400. The microstructure of metal layers is tailored near the onset of grain growth to control the surface density of grains resulting in small average sizes of grains to sub-nanometers. This generates concurrently desirable atomically sharp interfaces, high optical contrast, and desirable stress properties over a large number of periods, which have evidence through the developed ML optics. We demonstrate significantly high reflectivities of ML optics measured in the energy range 10–20 keV, except for d = 1.23 nm due to quasi-continuous layers. The reflectivities at soft gamma-rays are predicted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

SOI-Based High-Voltage, High-Temperature Integrated Circuit Gate Driver for SiC-Based Power FETs

Silicon carbide (SiC)-based field effect transistors (FETs) are gaining popularity as switching elements in power electronic circuits designed for high-temperature environments like hybrid electric vehicle, aircraft, well logging, geothermal power generation etc. Like any other power switches, SiC-based power devices also need gate driver circuits to interface them with the logic units. The placement of the gate driver circuit next to the power switch is optimal for minimizing system complexity. Successful operation of the gate driver circuit in a harsh environment, especially with minimal or no heat sink and without liquid cooling, can increase the power-to-volume ratio as well as the power-to-weight ratio for power conversion modules such as a DC-DC converter, inverter etc. A silicon-on-insulator (SOI)-based high-voltage, high-temperature integrated circuit (IC) gate driver for SiC power FETs has been designed and fabricated using a commercially available 0.8-m, 2-poly and 3-metal bipolar-complementary metal oxide semiconductor (CMOS)-double diffused metal oxide semiconductor (DMOS) process. The prototype circuit-s maximum gate drive supply can be 40-V with peak 2.3-A sourcing/sinking current driving capability. Owing to the wide driving range, this gate driver IC can be used to drive a wide variety of SiC FET switches (both normally OFF metal oxide semiconductor field effect transistor (MOSFET) and normally ON junction field effect transistor (JFET)). The switching frequency is 20-kHz and the duty cycle can be varied from 0 to 100-. The circuit has been successfully tested with SiC power MOSFETs and JFETs without any heat sink and cooling mechanism. During these tests, SiC switches were kept at room temperature and ambient temperature of the driver circuit was increased to 200-C. The circuit underwent numerous temperature cycles with negligible performance degradation.

33 ADVANCED PROPULSION SYSTEMS↗

Strategies for Developing High-Volume Fly Ash Concrete with High Early-Age Strength for Precast Applications

Partial replacement of portland cement with supplementary cementitious materials (SCMs), such as fly ash, is an effective strategy for improving durability and reducing the CO 2 footprint of concrete. However, using high-volume fly ash (HVFA) binders in precast and prestressed concrete is currently limited; largely due to reduced early-age strength development that impedes rapid production and prestressing of precast concrete. To investigate and address this challenge, HVFA mortars with a minimum of 40% fly ash by mass of cementitious materials were developed and tested in this study. Two fresh fly ashes (an ASTM C618 Class F and a Class C) and a landfilled fly ash (Class F) were included. Various strategies for improving the early strength were evaluated, including gypsum optimization, chemical accelerators, steam curing, use of CSA cements, and adding other reactive SCMs like silica fume, calcined clay, and slag cement. Steam curing and the use of CSA cement at high dosages (40% of total binder) were found to be the most successful strategies across all three fly ashes. Additionally, significant improvements were observed with gypsum optimization (for Class C fly ash) and the use of accelerators (for Class F fly ashes), and these strategies are likely to be more feasible considering later-age strength and economic viability. Interestingly, HVFA mixtures made with the landfilled fly ash used in this study were able to achieve high early strengths with water-to-cementitious materials ratio adjustment alone. As a result, these HVFA mixtures were also found to be less responsive to accelerators when compared to the fresh Class F fly ash, highlighting an important distinction between the materials despite the similarity in chemical composition.

42 ENGINEERING↗

High-intensity xenon plasma discharge lamp for bulk-sensitive high-resolution photoemission spectroscopy

We have developed a highly brilliant xenon (Xe) discharge lamp operated by microwave-induced electron cyclotron resonance (ECR) for ultrahigh-resolution bulk-sensitive photoemission spectroscopy (PES). We observed at least eight strong radiation lines from neutral or singly ionized Xe atoms in the energy region of 8.4-10.7 eV. The photon flux of the strongest Xe I resonance line at 8.437 eV is comparable to that of the He I{alpha} line (21.218 eV) from the He-ECR discharge lamp. Stable operation for more than 300 h is achieved by efficient air-cooling of a ceramic tube in the resonance cavity. The high bulk sensitivity and high-energy resolution of PES using the Xe lines are demonstrated for some typical materials.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Production of high-density capacitive plasma by the effects of multihollow cathode discharge and high-secondary-electron emission

High-density capacitively coupled plasma with electron density of 10{sup 11} cm{sup -3} was produced with the effects of the multihollow cathode discharge and the high-secondary-electron emission from radio frequency (rf)-biased electrode using Ar gas. It was found that the optimum pressure was around 3-15 Pa. In the case of only multihollow cathode discharge, the plasma density increased from 1.2x10{sup 10} to 8x10{sup 10} cm{sup -3} with the increasing distance z from the cathode electrode for 5 mm<z<15 mm. Moreover, plasma density increased with increasing voltage of rf-biased electrode. The rate of deposited amorphous hydrocarbon thin films of about 200 nm/min was attained with the high-density rf plasma enhanced chemical vapor deposition using CH{sub 4} gas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Gamma ray spectroscopy at high energy and high time resolution at JET

In fusion plasmas gamma ray emission is caused by reactions of fast particles, such as fusion alpha particles, with impurities. Gamma ray spectroscopy at JET has provided valuable diagnostic information on fast fuel as well as fusion product ions. Improvements of these measurements are needed to fully exploit the flux increase provided by future high power experiments at JET and ITER. Limiting aspects are, for instance, the count rate capability due to a high neutron/gamma background combined with slow detector response and a modest energy resolution due to the low light yield of the scintillators. This paper describes the solutions developed for achieving higher energy resolution, signal to background, and time resolution. The detector design is described based on the new BrLa{sub 3} scintillator crystal. The paper will focus on hardware development, including a photomultiplier tube capable of stable operation at counting rate as high as 1 MHz, the magnetic shielding, and the fast digital data acquisition system.

36 MATERIALS SCIENCE↗

High-density magnetohydrodynamic energy conversion in a high-temperature inert gas

We describe high-density magnetohydrodynamic (MHD) energy conversion in a high-temperature seed-free argon plasma, for which a compact disk-shaped Hall-type radial-flow MHD electrical power generator is used. The state of the MHD power-generating plasma changes with increasing total inflow temperature from 8200 to 9400 K; unstable behavior accompanied by the appearance of fine structures is transformed to a homogeneous and stable state. The attained enthalpy extraction efficiency is comparable to previous results using a conventional seeded gas. Furthermore, a high power output density is achieved even in relatively low-density magnetic flux.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High order reflectivity of highly oriented pyrolytic graphite crystals for x-ray energies up to 22 keV

We used Kr K{alpha} (12.6 keV), Zr K{alpha} (15.7 keV), and Ag K{alpha} (22.2 keV) x-rays, produced by petawatt-class laser pulses, to measure the integrated crystal reflectivity R{sub int} of flat highly oriented pyrolytic graphite (HOPG) up to the fifth order. The maximum R{sub int} was observed in first order (3.7 mrad at 12.6 keV), decreasing by a factor of 3-5 for every successive order, and dropping by a factor of 2-2.5 at 22.2 keV. The current study indicates that HOPG crystals are suitable for measuring scattering signals from high energy x-ray sources (E{>=}20 keV). These energies are required to penetrate through the high density plasma conditions encountered in inertial confinement fusion capsule implosions on the National Ignition Facility.

07 ISOTOPE AND RADIATION SOURCES↗

A diamond anvil cell with resistive heating for high pressure and high temperature x-ray diffraction and absorption studies

In this paper we describe a prototype of a diamond anvil cell (DAC) for high pressure/high temperature studies. This DAC combines the use of a resistive oven of 250 W power in a very small volume, associated with special conical seats for Boehler-type diamond anvils in order to have a large angular acceptance. To protect the diamond anvils from burning and to avoid the oven oxidation, the heated DAC is enclosed in a vacuum chamber. The assemblage was used to study the melting curve of germanium at high pressure (up to 20 GPa) and high temperature (up to 1200 K) using x-ray diffraction and x-ray absorption spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Highly textured SmCo{sub 5} (001) thin film with high coercivity

The seedlayer effect on crystallographic structure and magnetic properties of cosputtered SmCo films on Cu underlayer was investigated. Highly textured (001) SmCo{sub 5} thin films were obtained by introducing a thin Ti or Ta seedlayer. Especially, with the Ta seedlayer, the half maximum of the rocking curve of SmCo (001) peak was as small as 3.4 deg. and the high-index SmCo{sub 5} (003) diffraction peak was clearly observed, showing a high quality of texture and crystallinity. The SmCo{sub 5} films showed a large perpendicular anisotropy with out-of-plane coercivities over 20 kOe. Well crystallized SmCo{sub 5} films with (001) texture could be obtained at a temperature as low as 325 deg. C. The crystallinity, (001) texture, and magnetic properties of SmCo{sub 5} thin films were found to be dependent on deposition temperature, the texture of the Cu (111) underlayer, roughness of the Cu underlayer, and formation of SmCoCu alloy through the Cu diffusion.

36 MATERIALS SCIENCE↗

High precision high voltage divider and its application to electron beam ion traps

A high precision high voltage divider has been developed for the electron beam ion trap in Shanghai. The uncertainty caused by the temperature coefficient of resistance (TCR) and the voltage coefficient of resistance has been studied in detail and was minimized to the level of ppm (10{sup -6}) range. Once the TCR was matched between the resistors, the precision of the dividing ratio finally reached the ppm range also. We measured the delay of the divider caused by the capacitor introduced to minimize voltage ripple to be 2.35 ms. Finally we applied the divider to an experiment to measure resonant energies for some dielectronic recombination processes for highly charged xenon ions. The final energies include corrections for both space charge and fringe field effects are mostly under 0.03%.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Enhanced growth of high quality single crystal diamond by microwave plasma assisted chemical vapor deposition at high gas pressures

Single crystals of diamond up to 18 mm in thickness have been grown by microwave plasma assisted chemical vapor deposition at gas pressures of up to 350 torr. Growth rates of up to 165 {mu}m/h at 300 torr at high power density have been achieved. The processes were evaluated by optical emission spectroscopy. The high-quality single-crystal diamond grown at optimized conditions was characterized by UV-visible absorption and photoluminescence spectroscopy. The measurements reveal a direct relationship between residual absorption and nitrogen content in the gas chemistry. Fabrication of high quality single-crystal diamond at higher growth rates should be possible with improved reactor design that allows still higher gas synthesis pressures.

36 MATERIALS SCIENCE↗

Generating Polarized High-Brightness Muon Beams With High-Energy Gammas

Hadron colliders are impractical at very high energies as effective interaction energy is a fraction of the energies of the beams and luminosity must rise as energy squared. Further, the prevailing gluon-gluon background radiation makes it difficult to sort out events. e{sup +}e{sup -} colliders, on other hand, are constrained at TeV energies by beamstrahlung radiation and also by cost as long linacs are required to avoid synchrotron radiation in the rings. A muon collider will have the same advantages in energy reach as an e{sup +}e{sup -} collider, but without prohibitive beamstrahlung- and synchrotron- radiation. Generation of the high-brightness polarized muon ({mu}{sup -}{mu}{sup +}) beams through gamma conversion into pairs in the nuclei field is considered in this paper. The dominant effect in the interaction of the high-energy photons with the solid target will be the production of electron-positron pairs. The low-phase space of the resulting muon beams adequately compensates for the small probability of generating a {mu}{sup -}{mu}{sup +} pair.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High energy x-ray diffraction/x-ray fluorescence spectroscopy for high-throughput analysis of composition spread thin films

High-throughput crystallography is an important tool in materials research, particularly for the rapid assessment of structure-property relationships. We present a technique for simultaneous acquisition of diffraction images and fluorescence spectra on a continuous composition spread thin film using a 60 keV x-ray source. Subsequent noninteractive data processing provides maps of the diffraction profiles, thin film fiber texture, and composition. Even for highly textured films, our diffraction technique provides detection of diffraction from each family of Bragg reflections, which affords direct comparison of the measured profiles with powder patterns of known phases. These techniques are important for high throughput combinatorial studies as they provide structure and composition maps which may be correlated with performance trends within an inorganic library.

36 MATERIALS SCIENCE↗

High frequency, high time resolution time-to-digital converter employing passive resonating circuits

A method for measuring time intervals accurate to the picosecond range is based on phase measurements of oscillating waveforms synchronous with their beginning and/or end. The oscillation is generated by triggering an LC resonant circuit, whose capacitance is precharged. By using high Q resonators and a final active quenching of the oscillation, it is possible to conjugate high time resolution and a small measurement time, which allows a high measurement rate. Methods for fast analysis of the data are considered and discussed with reference to computing resource requirements, speed, and accuracy. Experimental tests show the feasibility of the method and a time accuracy better than 4 ps rms. Methods aimed at further reducing hardware resources are finally discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗