Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

INL/JOU-17-41026-Rev000

Graphite creep strain data from the irradiation creep capsule Advanced Graphite Creep-1 (AGC-1) are reported. This capsule was the first (prototype) of a series of five or six capsules planned as part of the AGC experiment, which was designed to fully characterize the effects of neutron irradiation and the radiation creep behavior of current nuclear graphite. The creep strain data and analysis are reported for the six graphite grades incorporated in the capsule. The AGC-1 capsule was irradiated in the Advanced Test Reactor at Idaho National Laboratory (INL) at approximately 700°C and to a peak dose of 7 dpa (displacements per atom). The specimen’s final dose, temperature, and stress conditions have been reported by INL and were used during this analysis. The derived creep coefficients (K) were calculated for each grade and were found to compare well to literature data for the creep coefficient, even under the wide range of AGC-1 specimen temperatures. Comparisons were made between AGC-1 data and historical grade data for creep coefficients.

36 MATERIALS SCIENCE↗

Preparation of mesocarbon microbeads and subsequent heating treatment - article no. A27

The preparation of mesocarbon microbeads (MCMB) has been studied by heating coal tar pitch with different phenyl silicone oil content at 350 {sup o}C for 2h. The spheres with diameters ranging from 0.54 to 11.4 {mu} m were obtained. The as-extracted MCMB when the silicone oil/coal pitch value was 3 had a very homogeneous size, a small diameter and also an excellent sphericity. The yield of MCMB was 8.3%, and microcrystalline structure was better. After stabilization, the spheres carbonized at 900 {sup o}C still kept spherical, but broken into small particles during the graphitization. The stabilization destroyed the microcrystalline structure of as-extracted MCMB, but the microcrystalline structure became better after carbonization. The structure of graphitized MCMB at 2300{sup o}C was close to the graphite structure, and clear graphitization fringes were observable.

01 COAL, LIGNITE, AND PEAT↗

Enhancing VHTR passive safety and economy with thermal radiation based direct reactor auxiliary cooling system

One of the most important requirements for Gen. IV Very High Temperature Reactor (VHTR) is passive safety. Currently all the gas cooled version of VHTR designs use Reactor Vessel Auxiliary Cooling System (RVACS) for passive decay heat removal. The RVACS can be characterized as a surface-based decay heat removal system. It is especially suitable for smaller power reactors since small systems have relatively larger surface area to volume ratio. However, RVACS limits the maximum achievable power level for modular VHTRs due to the mismatch between the reactor power (proportional to the core volume) and decay heat removal capability (proportional to the vessel surface area). Besides the safety considerations, VHTRs also need to be economical in order to compete with other reactor concepts and other types of energy sources. The limit of decay heat removal capability set by using RVACS has affected the economy of VHTRs. A potential alternative solution is to use a volume-based passive decay heat removal system, called Direct Reactor Auxiliary Cooling Systems (DRACS), to remove or mitigate the limitation on decay heat removal capability. DRACS composes of natural circulation loops with two sets of heat exchangers, one on the reactor side and another on the environmental side. For the reactor side, cooling pipes will be inserted into holes made in the outer or inner graphite reflector blocks. There will be gaps or annular regions formed between these cooling pipes and their corresponding surrounding graphite surfaces. Graphite has an excellent heat conduction property. By taking advantage of this feature, we can have a volume-based method to remove decay heat. The scalability can be achieved, if needed, by employing more rows of cooling pipes to accommodate higher decay heat rates. Since heat can easily conduct through the graphite regions among the holes made for the cooling pipes, those cooling pipes located further away from the active core region can still be very effective in removing decay heat. By removing the limit on the decay heat removal capability due to the limited available surface area as in a RVACS, the reactor power density and therefore the reactor power can be significantly increased, without losing the passive heat removal feature. This paper introduces the concept of using DRACS to enhance VHTR passive safety and economics. Three design options with different cooling pipe locations are discussed. Analysis results from a lumped volume based model and CFD simulations are presented. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Pebble fuel design for the PB-FHR

This paper presents the results of parametric studies of pebble fuel that can guide the design of future PB-FHR cores. The pebble fuel designs are assessed using the following performance characteristics: burnup, reactivity feedback, transient response, timescale to reach equilibrium cycle, and protection of structural components. The performance of a thorium pebble blanket is assessed by comparing against a seed-only system and system that utilizes a graphite pebble reflector instead of a thorium blanket. This paper presents the functional requirements and a methodology to assess these fuel pebble designs. This paper identifies a feasible design space for low enriched uranium pebbles and selected a baseline pebble design for safe, economic energy generation. Furthermore, this study finds a thorium blanket does not increase the performance of the system significantly with respect to a graphite pebble reflector. Therefore, a graphite pebble reflector is recommended in the baseline full-core design to extend the lifetime of the outer solid graphite reflector to the life of plant. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Identification and Quantification of Carbon Phases in Conversion Fuel for the Transient Reactor Test Facility

As part of an overall effort to convert US research reactors to low-enriched uranium (LEU) fuel, a LEU conversion fuel is being designed for the Transient Reactor Test Facility (TREAT) at the Idaho National Laboratory. TREAT fuel compacts are comprised of UO{sub 2} fuel particles in a graphitic matrix material. In order to refine heat transfer modeling, as well as determine other physical and nuclear characteristics of the fuel, the amount and type of graphite and non-graphite phases within the fuel matrix must be known. In this study, we performed a series of complementary analyses, designed to allow detailed characterization of the graphite and phenolic resin based fuel matrix. Methods included Scanning Electron Microscopy, Raman spectroscopy, and X-ray Diffraction. Our results indicate that no single characterization technique will yield all of the desired information; however, through the use of statistical and empirical data analysis, such as curve fitting, partial least squares regression, volume extrapolation and spectra peak ratios, a degree of certainty for the quantity of each phase can potentially be obtained. Although no one type of analysis has provided a complete determination of the quantities and identities of all carbon phases present in the fuel matrix, additional information has been gathered and is being used to refine future analysis methods. From the three types of quantification performed, results have been within 1% (92.8%, 93.02% and 93.6% for BSE image analysis, XRD and Raman spectroscopy, respectively). More work remains to identify any trace crystalline carbonaceous phases that may be present, quantify any traces that are identified, and develop and use further complementary bulk phase quantification techniques. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The electric current effect on electrochemical deconsolidation of spherical fuel elements - 18447

For High-Temperature Gas-cooled Reactor in China, fuel particles are bonded into spherical fuel elements by a carbonaceous matrix. In conjunction with the development of a system to determine fuel failure fractions through {gamma}-analysis of individual and undamaged fuel particles, an automated electrochemical deconsolidation apparatus was developed in this study to separate the particles from the carbonaceous matrix by disintegrating the matrix into fine graphite powder, based on the anodic oxidation of graphite in an electrolyte containing nitric acid. A series of tests were conducted under a range of deconsolidation conditions to develop procedures and refine the equipment. The easy-handle un-irradiated spherical fuel elements were used as samples for initial tests. It is found that the morphology, size, and element content of deconsolidated graphite matrix and free particles were notably affected by electric current intensity. During the electrolysis, the nitric acid electrolyte gradually infiltrated into the micropores of graphite matrix, and the electrochemical reaction would take place around micropore structure as well as matrix surface. With much higher surface reaction capability due to the large specific area of micropore structure, the expansion stress originated from inner surface of micropores widened the c-spacing of the layer lattice of carbonaceous matrix, which was thought to be one of the main driving force of deconsolidation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design of dehumidification test of HTR-PM - 18461

Moisture in the primary loop is harmful for the normal operation of the Modular High Temperature Gas-cooled Reactor (MHTGR). A dehumidification test to remove the moisture in the primary loop of the High Temperature Gas-cooled Reactor Pebble-bed Module (HTR-PM) reactor was proposed. This test consisted of two stages, stage A and stage B. The test process of stage A was divided into six steps including vacuuming, inflating, heating, dehumidifying, cooling and venting, while the test process of stage B only included the first five steps of stage A. Nitrogen and helium were respectively used as the dehumidification gas to carry away the moisture in the graphite in stage A and stage B, which were circulated and heated by the helium blower. What s more, preliminary calculations to heating and dehumidifying were implemented. Variations of water content of the graphite in the dehumidification process were obtained, and the times spent for different dehumidification targets were also worked out. It needs 19.5 days to remove 80% of the moisture in the graphite in stage A when the dehumidification temperature is 150 deg. C, and 14.3 days are needed to make water content in the graphite decrease from 20% to 5% in stage B. The results show that the test method proposed is feasible and effective, and offer references to the design, test and operation of the HTR-PM. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Improving the AGR Fuel Testing Power Density Profile Versus Irradiation-Time in the Advanced Test Reactor

The Very High Temperature gas-cooled Reactor (VHTR), which is currently being developed, achieves simplification of safety through reliance on ceramic-coated fuel particles. Each TRISO-coated fuel particle has its own containment which serves as the principal barrier against radionuclide release under normal operating and accident conditions. These fuel particles, in the form of graphite fuel compacts, are currently undergoing a series of irradiation tests in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL) to support the Advanced Gas-Cooled Reactor (AGR) fuel qualification program. A representive coated fuel particle with an 235U enrichment of 19.8 wt% was used in this analysis. The fuel burnup analysis tool used to perform the neutronics study reported herein, couples the Monte Carlo transport code MCNP, with the radioactive decay and burnup code ORIGEN2. The fuel burnup methodology known as Monte-Carlo with ORIGEN2 (MCWO) was used to evaluate the AGR experiment assembly and demonstrate compliance with ATR safety requirements. For the AGR graphite fuel compacts, the MCWO-calculated fission power density (FPD) due to neutron fission in 235U is an important design parameter. One of the more important AGR fuel testing requirements is to maintain the peak fuel compact temperature close to 1250°C throughout the proposed irradiation campaign of 550 effective full power days (EFPDs). Based on the MCWO-calculated FPD, a fixed gas gap size was designed to allow regulation of the fuel compact temperatures throughout the entire fuel irradiation campaign by filling the gap with a mixture of helium and neon gases. The chosen fixed gas gap can only regulate the peak fuel compact temperature in the desired range during the irradiation test if the ratio of the peak power density to the time-dependent low power density (P/T) at 550 EFPDs is less than 2.5. However, given the near constant neutron flux within the ATR driver core and the depletion of 235U in the graphite fuel compacts versus EFPD, the P/T ratio was calculated to be 5.3, which is unacceptable given the fuel compact temperature control requirement. To flatten the FPD profile versus EFPDs, two proposed options are – (a) add fertile (232Th) particles to the fuel compact and (b) add burnable absorber (B4C) to the graphite holder. The effectiveness of these two proposed options to flatten the FPD profile versus EFPDs were investigated and the results are compared in this study.

99 GENERAL AND MISCELLANEOUS↗

Manipulating Adsorption-Insertion Mechanisms in Nanostructured Carbon Materials for High-Efficiency Sodium Ion Storage

Hard carbon is one of the most promising anode materials for sodium-ion batteries, but the low coulombic efficiency is still a key barrier. In this paper we synthesized a series of nanostructured hard carbon materials with controlled architectures. Using a combination of in-situ XRD mapping, ex-situ NMR, EPR, electrochemical techniques and simulations, an “adsorption-intercalation” (A-I) mechanism is established for Na ion storage. During the initial stages of Na insertion, Na ions adsorb on the defect sites of hard carbon with a wide adsorption energy distribution, producing a sloping voltage profile. In the second stage, Na ions intercalate into graphitic layers with suitable spacing to form NaCx compounds similar to the Li ion intercalation process in graphite, producing a flat low voltage plateau. The cation intercalation with a flat voltage plateau should be enhanced and the sloping region should be avoided. Guided by this knowledge, non-porous hard carbon material has been developed which has achieved high reversible capacity and coulombic efficiency to fulfill practical application.

Qiu, Shen↗

Low-Defect and Low-Porosity Hard Carbon with High Coulombic Efficiency and High Capacity for Practical Sodium Ion Battery Anode

Hard carbon is regarded as the most promising anode material for commercialization of Na ion batteries because of its high capacity and low cost. At present, the practical utilization of hard carbon anodes is largely limited by the low initial Coulombic efficiency (ICE). Na ions have been found to adopt an adsorption–insertion storage mechanism. In this paper a systematic way to control the defect concentration and porosity of hard carbon with similar overall architectures is shown. This study elucidates that the defects in the graphite layers are directly related to the ICE as they would trap Na ions and create a repulsive electric field for other Na ions so as to shorten the low-voltage intercalation capacity. The obtained low defect and porosity hard carbon electrode has achieved the highest ICE of 86.1% (94.5% for pure hard carbon material by subtracting that of the conductive carbon black), reversible capacity of 361 mA h g-1, and excellent cycle stability (93.4% of capacity retention over 100 cycles). This result sheds light on feasible design principles for high performance Na storage hard carbon: suitable carbon layer distance and defect free graphitic layers.

Xiao, Lifen↗

Enhancing the thermosiphon-driven discharge of a latent heat thermal storage system used in a personal cooling device

Personal cooling devices reduce energy loads by allowing buildings to operate with elevated setpoint temperatures, without compromising on the occupant comfort. One such novel technology called the Roving Comforter (RoCo) uses a compact R134a based vapor compression system for cooling. Following its cooling operation, during which waste heat from the condensing refrigerant is stored in a phase change material (PCM), a two-phase loop thermosiphon is used to discharge (solidify) the PCM to enable its next operation. The transient operation of this thermosiphon is the focus of the present paper. Use of a PCM as the storage medium provides high energy density due to the ability to store thermal energy as latent heat during the phase transition; however, the discharge rate is limited by the low thermal conductivity of the PCM. Insertion of a graphite foam within the PCM can increase the rate of discharge and decrease the downtime of the cooling device. Since graphite enhancement involves a tradeoff between improving the discharge time at the expense of PCM volumetric latent heat, the impact of graphite foam density on the PCM discharge rate is investigated by using a Modelica-based transient model of the thermosiphon. The semi-empirical model, which uses relevant heat transfer coefficient and pressure drop correlations for both refrigerant and airside heat transfer, captures the complex phenomena involving simultaneous phase change of the refrigerant and the PCM. Finally, the graphite enhanced PCM selected from this analysis results in a 51% reduction in the discharge time with addition of only 5% to the thermal storage weight, without compromising the required cooling time.

42 ENGINEERING↗

Carburization of metals by a chemical mechanism of carbon transport through molten fluoride salts

Carburization of structural alloys used in Fluoride Cooled High Temperature Reactors (FHR) can result from the interaction between the metal and graphite components and cause changes in alloy properties. However, carburization requires transport of carbon from graphite to alloy surfaces through the molten fluoride coolant. This work introduces an alternative to previously proposed carbon transport mechanisms. The new mechanism is based on the generation of carbonate ions (CO 3 2- ) by oxide impurities in the salt reacting with graphite. CO 3 2- is then reduced on metal surfaces to deposit carbon. This work demonstrates the reduction of dissolved CO 3 2- on pure Fe, Ni, Cr, Mo, and W surfaces without an applied potential in molten FLiNaK at 700 °C. Finally, we also demonstrate that the interaction between oxide and graphite in molten FLiNaK media produces CO 3 2- .

36 MATERIALS SCIENCE↗

Operando NMR and XRD study of chemically synthesized LiCx oxidation in a dry room environment

We test the stability of pre-lithiated graphite anodes for Li-ion batteries in a dry room battery processing room. The reaction between LiCx and laboratory air was followed using operando NMR and x-ray diffraction as these methods are sensitive to change in Li stoichiometry in graphite. There is minimal reactivity between LiC 6 and N 2 , CO 2 or O 2 ; however, LiC 6 reacts with moisture to form lithium (hydr)oxide. The reaction rate follows zero-order kinetics with respects to intercalated lithium suggesting that lithium transport through the graphite is fast. The reaction mechanism occurs by sequential formation of higher stages LiC 12 , then LiC 18 , and then LiC 24 as the hydrolysis proceeds to the formation of Li x OH y and graphite end products. Slowing down the formation rate of the Li x OH y passivation layer stabilizes of the higher stages.

25 ENERGY STORAGE↗

Unusual Enhancement in Intrinsic Thermal Conductivity of Multilayer Graphene by Tensile Strains

High basal plane thermal conductivity k of multi-layer graphene makes it promising for thermal management applications. Here we examine the effects of tensile strain on thermal transport in this system. Using a first principles Boltzmann-Peierls equation for phonon transport approach, we calculate the room-temperature in-plane lattice k of multi-layer graphene (up to four layers) and graphite under different isotropic tensile strains. The calculated in-plane k of graphite, finite mono-layer graphene and 3-layer graphene agree well with previous experiments. The dimensional transitions of the intrinsic k and the extent of the diffusive transport regime from mono-layer graphene to graphite are presented. We find a peak enhancement of intrinsic k for multi-layer graphene and graphite with increasing strain and the largest enhancement amplitude is about 40%. In contrast the calculated intrinsic k with tensile strain decreases for diamond and diverges for graphene, we show that the competition between the decreased mode heat capacities and the increased lifetimes of flexural phonons with increasing strain contribute to this k behavior. Similar k behavior is observed for 2-layer hexagonal boron nitride systems, suggesting that it is an inherent thermal transport property in multi-layer systems assembled of purely two dimensional atomic layers. This study provides insights into engineering k of multi-layer graphene and boron nitride by strain and into the nature of thermal transport in quasi-two-dimensional and highly anisotropic systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tuning Strong Metal–Support Interactions via Synergistic Alloying

The encapsulation phenomenon associated with strong metal-support interaction (SMSI) has been largely restricted to catalyst systems consisting of group VIII metals with high surface energy and reducible transition metal oxide supports with low surface energy. Here, we demonstrate an encapsulation phenomenon that, while sharing morphological similarities with conventional SMSI, follows a distinctive pathway. This is shown by the encapsulation of CuAu nanoparticles (NPs) supported on highly ordered pyrolytic graphite (HOPG). Through dynamic monitoring of Cu, Au, and Cu 50 Au 50 NPs in an oxidizing atmosphere using ambient-pressure X-ray photoelectron spectroscopy, we show that this spontaneous encapsulation is achieved through the synergistic effect of the alloying elements. Specifically, the surface segregation of Cu promotes dissociative O 2 adsorption, leading to the formation of atomic O species, while the subsurface enrichment of Au hinders O incorporation into the bulk of CuAu NPs. Consequently, O spillover onto the graphite support occurs, resulting in the oxidation of the HOPG surface into graphitic oxide species. The higher affinity of the graphitic oxide species toward the Cu-segregated surface prompts their migration from the HOPG support to encapsulate the CuAu NPs. Finally, these results transcend the conventional SMSI and bear practical implications for the design and development of heterogeneous catalysts, particularly in carbon-supported alloy systems.

36 MATERIALS SCIENCE↗

Nonflammable Electrolytes for Lithium Ion Batteries Enabled by Ultraconformal Passivation Interphases

Occasional fire accidents and continuous battery safety concerns require advanced lithium ion batteries (LIBs) with high safety as well as great battery performances. The electrolyte plays a critical role in electrochemical and safety properties. Organic phosphate solvents next to the state-of-the-art organic carbonates could formulate nonflammable electrolytes and intrinsically eliminate fire hazards, but their poor compatibility with the graphite anodes remains an obstacle for practical applications. This work reports a promising approach by formulating localized high concentration electrolytes based on a phosphate solvent, ethylene carbonate and a partially fluorinated ether. This electrolyte readily generates robust solid electrolyte interphase on graphite anode and cathode electrolyte interphase on LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode. As a result, this electrolyte shows good compatibility with high voltage cathode and graphite anode, and enables long-term cycling stability in graphite||NMC811 cells. This work sheds a new light in development of nonflammable electrolytes for high energy-density LIBs.

Non-flammable electrolyte, lithium ion battery, lo↗

Formation and Inhibition of Metallic Lithium Microstructures in Lithium Batteries Driven by Chemical Crossover

The formation of metallic lithium microstructures in the form of dendrites or mosses at the surface of anode electrodes (e.g., lithium metal, graphite, and silicon) leads to rapid capacity fade and poses grave safety risks in rechargeable lithium batteries. In this work, we present here a direct, relative quantitative analysis of lithium deposition on graphite anodes in pouch cells under normal operating conditions, paired with a model cathode material, the layered nickel-rich oxide LiNi 0.61 Co 0.12 Mn 0.27 O 2 , over the course of 3000 charge-discharge cycles. Secondary-ion mass spectrometry chemically dissects the solid-electrolyte interphase (SEI) on extensively cycled graphite with virtually atomic depth resolution and reveals substantial growth of Li-metal deposits. With the absence of apparent kinetic (e.g., fast charging) or stoichiometric restraints (e.g., overcharge) during cycling, we show lithium deposition on graphite is triggered by certain transition-metal ions (manganese in particular) dissolved from the cathode in a disrupted SEI. This insidious effect is found to initiate at a very early stage of cell operation (<200 cycles) and can be effectively inhibited by substituting a small amount of aluminum (~1 mol %) in the cathode, resulting in much reduced transition-metal dissolution and drastically improved cyclability. In conclusion, our results may also be applicable to studying the unstable electrodeposition of lithium on other substrates, including Li metal.

25 ENERGY STORAGE↗