Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Experimental methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,711 records · Page 95

Nanoindentation of HMX and Idoxuridine to Determine Mechanical Similarity

Assessing the mechanical behavior (elastic properties, plastic properties, and fracture phenomena) of molecular crystals is often complicated by the difficulty in preparing samples. Pharmaceuticals and energetic materials in particular are often used in composite structures or tablets, where the individual grains can strongly impact the solid behavior. Nanoindentation is a convenient method to experimentally assess these properties, and it is used here to demonstrate the similarity in the mechanical properties of two distinct systems: individual crystals of the explosive cyclotetramethylene tetranitramine (HMX) and the pharmaceutical idoxuridine were tested in their as-precipitated state, and the effective average modulus and hardness (which can be orientation dependent) were determined. Both exhibit a hardness of 1.0 GPa, with an effective reduced modulus of 25 and 23 GPa for the HMX and idoxuridine, respectively. They also exhibit similar yield point behavior. This indicates idoxuridine may be a suitable mechanical surrogate (or “mock”) for HMX. While the methodology to assess elastic and plastic properties was relatively insensitive to specific crystal orientation (i.e., a uniform distribution in properties was observed for all random crystals tested), the indentation-induced fracture properties appear to be much more sensitive to tip-crystal orientation, and an unloading slope analysis is used to demonstrate the need for further refinement in relating toughness to orientation in these materials with relatively complex slip systems and crystal structures. View Full-Text

36 MATERIALS SCIENCE↗

The IEC 61850 Sampled Measured Values Protocol: Analysis, Threat Identification, and Feasibility of Using NN Forecasters to Detect Spoofed Packets

The operation of the smart grid is anticipated to rely profoundly on distributed microprocessor-based control. Therefore, interoperability standards are needed to address the heterogeneous nature of the smart grid data. Since the IEC 61850 emerged as a wide-spread interoperability standard widely accepted by the industry, the Sampled Measured Values method has been used to communicate digitized voltage and current measurements. Realizing that current and voltage measurements (i.e., feedback measurements) are necessary for reliable and secure noperation of the power grid, firstly, this manuscript provides a detailed analysis of the Sampled Measured Values protocol emphasizing its advantages, then, it identifies vulnerabilities in this protocol and explains the cyber threats associated to these vulnerabilities. Secondly, current efforts to mitigate these vulnerabilities are outlined and the feasibility of using neural network forecasters to detect spoofed sampled values is investigated. It was shown that although such forecasters have high spoofed data detection accuracy, they are prone to the accumulation of forecasting error. Accordingly, this paper also proposes an algorithm to detect the accumulation of the forecasting error based on lightweight statistical indicators. The effectiveness of the proposed methods is experimentally verified in a laboratory-scale smart grid testbed.

97 MATHEMATICS AND COMPUTING↗

Evaluation of Corrosion and Its Impact on the Mechanical Performance of Al–Steel Joints

Aluminum–steel joints are increasingly used in the automotive industry to meet the requirements for energy saving and emission reduction. Among various joining technologies, self-pierce riveting (SPR) and resistance spot welding (RSW) are two well-established technologies for fabricating dissimilar joints with stable and high mechanical performance. However, corrosion will occur in these joints inevitably due to different electrochemical properties, which can degrade the surface quality and the mechanical performance, such as strength. This paper presents a method of understanding the corrosion mechanisms in joining aluminum and steel. For this understanding, a hybrid method combining experimental observations, mechanical properties identification, and analytical approaches was used to assess the evolution of the impact of corrosion on the joining performance, such as traction separation curves. The study was conducted on common combinations used in the vehicles, e.g., a 1.2 mm thickness aluminum alloy (AA 6022) and 2.0 mm thickness hot deep galvanized steel (HDG HSLA 340) joined by SPR and RSW. After the fabrication of these joints, accelerated cyclic corrosion tests of up to 104 cycles were performed, which reproduced the environmental conditions to which a vehicle was exposed. By investigating the microstructural evolution within the joints, the corrosion mechanisms of SPR and RSW joints were revealed, including the initiation and propagation. Moreover, the intrinsic impact of the corrosion on the mechanical performance, including the strength, axial stiffness, and crashworthiness, was analyzed by performing a lap-shear test. It showed that as corrosion proceeds, the fracture modes and mechanical performance are affected significantly.

Chemistry↗

Roadmap for warm dense matter physics

This roadmap presents the state-of-the-art, current challenges and near future developments anticipated in the thriving field of warm dense matter physics. Originating from strongly coupled plasma physics, high pressure physics and high energy density science, the warm dense matter physics community has recently taken a giant leap forward. This is due to spectacular developments in laser technology, diagnostic capabilities, and computer simulation techniques. Only in the last decade has it become possible to perform accurate enough simulations \& experiments to truly verify theoretical results as well as to reliably design experiments based on predictions. Consequently, this roadmap discusses recent developments and contemporary challenges that are faced by theoretical methods, and experimental techniques needed to create and diagnose warm dense matter. A large part of this roadmap is dedicated to specific warm dense matter systems and applications in astrophysics, inertial confinement fusion and novel material synthesis.

FOS: Physical sciences↗

Analysis of complex elastic structures by a Rayleigh-Ritz component modes method using Lagrange multipliers

The free vibrations of elastic structures of arbitrary complexity were analyzed in terms of their component modes. The method was based upon the use of the normal unconstrained modes of the components in a Rayleigh-Ritz analysis. The continuity conditions were enforced by means of Lagrange Multipliers. Examples of the structures considered are: (1) beams with nonuniform properties; (2) airplane structures with high or low aspect ratio lifting surface components; (3) the oblique wing airplane; and (4) plate structures. The method was also applied to the analysis of modal damping of linear elastic structures. Convergence of the method versus the number of modes per component and/or the number of components is discussed and compared to more conventional approaches, ad-hoc methods, and experimental results.

Klein, L. R.↗

Lunar soil properties and soil mechanics

The long-range objectives were to develop methods of experimentation and analysis for the determination of the physical properties and engineering behavior of lunar surface materials under in situ environmental conditions. Data for this purpose were obtained from on-site manned investigations, orbiting and softlanded spacecraft, and terrestrial simulation studies. Knowledge of lunar surface material properties are reported for the development of models for several types of lunar studies and for the investigation of lunar processes. The results have direct engineering application for manned missions to the moon.

Mitchell, J. K.↗

Life prediction of thermal-mechanical fatigue using strain-range partitioning

The applicability is described of the method of Strainrange Partitioning to the life prediction of thermal-mechanical strain-cycling fatigue. An in-phase test on 316 stainless steel is analyzed as an illustrative example. The observed life is in excellent agreement with the life predicted by the method using the recently proposed Step-Stress Method of experimental partitioning, the Interation Damage Rule, and the life relationships determined at an isothermal temperature of 705 C. Implications of the study are discussed relative to the general thermal fatigue problem.

Halford, G. R.↗

Wind Tunnel Design Studies and Technical Evaluation of Advanced Cargo Aircraft Concepts

In support of aerodynamic studies relating to the design and performance prediction of the National Transonic Facility, the following main tasks were accomplished: (1) estimation of aerodynamic losses of the tunnel circuits, (2) refinement of the high-speed diffuser loss prediction method utilizing experimental data generated for the purpose; (3) model studies of flow in the second-turn and measurements of the fan inlet distortion and overall pressure loss; (4) development of a shortened fan nacelle configuration of improved aerodynamic performance; and (5) evolution through model studies of an efficient rapid-diffuser system as the key to a circuit-modification proposal to reduce volume and minimize liquid-nitrogen consumption, at the same time saving on the shell cost.

Rao, D. M.↗

Numerical method to calculate the induced drag or optimum loading for arbitrary non-planar aircraft

A simple unified numerical method applicable to non-planar subsonic aircraft has been developed for calculating either the induced drag for an arbitrary loading or the optimum aircraft loading which results in minimum induced drag. The method utilizes a vortex lattice representation of the aircraft lifting surfaces coupled with the classic equations and theorems for computing and minimizing induced drag. Correlation of results from the numerical method with non-planar solutions obtained from other more complex theories indicates very good agreement. Comparison of the induced-drag computations using the numerical method with experimental data for planar and non-planar configurations was also very good.

Blackwell, J. A., Jr.↗

Life prediction of thermal-mechanical fatigue using strainrange partitioning

This paper describes the applicability of the method of Strainrange Partitioning to the life prediction of thermal-mechanical strain-cycling fatigue. An in-phase test on 316 stainless steel is analyzed as an illustrative example. The observed life is in excellent agreement with the life predicted by the method using the recently proposed Step-Stress Method of experimental partitioning, the Interaction Damage Rule, and the life relationships determined at an isothermal temperature of 705 C. Implications of the present study are discussed relative to the general thermal fatigue problem.

Halford, G. R.↗

Measuring acoustic properties of materials and jet nozzles

Method measures acoustic properties of sound-absorbent materials and jet-nozzle system. Advantages of impulse method over other methods are that test time and complication are reduced. Results obtained from impulse method have been compared with those from existing methods, both experimental and theoretical, and show excellent agreement.

Dean, P. D.↗

A study of multiple-shaker modal survey testing

The principal objective was to examine and to assess the practical value of a method of multiple-shaker sinusoidal modal vibration testing known as Asher's method. Numerical studies which simulate the application of Asher's method and a unique experimental implementation of the method were completed. Another objective of the research was to develop and to demonstrate with numerical simulation a quantitative method for determining from transfer function data the number of dominant modes of vibration in sinusoidal structural response.

Hallauer, W. L., Jr.↗

An impulse test technique with application to acoustic measurements

A method has been presented for measuring the acoustic properties of an absorbent material and a duct/nozzle system (with or without airflow) using a high voltage spark discharge as an impulse source of sound. The cross-spectra of the incident, reflected and transmitted acoustic pressure transients are analyzed by way of a FFT digital processor in the form of complex transfer functions. These transfer functions have a direct relationship to the termination impedance and radiation directivity. The impulse method has been justified by comparisons, with data obtained from existing methods (both experimental and theoretical), that show excellent agreement. Reflection coefficients and radiation impedances of various duct-nozzle systems and their associated far-field directivities are also presented as some of the applications of the impulse technique.

Salikuddin, M.↗