Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “jets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Aeroacoustic characteristics of jet flap type exhausts.

This work which is intended to shed more light on the acoustic and fluid dynamic characteristics of jet flap type exhaust flows, reports and discusses some typical experimental results obtained with cold model air jets in a reverberation chamber. Acoustic data on the total sound power output and the overall noise spectrum of various jet flap configurations are given and compared with data from conventional circular jets. In addition various flow data for the same jets resulting from hot wire measurements are reported and general conclusions are obtained regarding the expected noise source distribution. The results indicate the dependence of the acoustic and flow characteristics on the major nozzle parameters. For the jet flaps the total radiated sound power is found to follow a 3 to 6 power of the exhaust velocity while for the circular jets the 8 power law is confirmed. The noise produced in the secondary mixing region downstream of the flap trailing edge tends to exceed the noise issuing from the primary mixing region.

Gruschka, H. D.↗

The influence of a crossflow on jet noise

The acoustic field generated by a circular jet in the presence of a low speed crossflow is calculated. The solution is obtained for a quadrupole source located in a uniformly moving acoustic medium. Ribner's work on straight jets is used to model the flow in the turbulent crossflow jet. The movement of the acoustic medium results in the acoustic intensity being greater upstream of the jet flow than at an equal distance downstream. A summary is also presented of the analysis for the acoustic intensity of a crossflow jet which is in motion through a stationary acoustic medium. The analysis is applicable to the noise generated by the lift jet of a V/STOL aircraft under take-off or landing conditions. The results of these two configurations provide a comparision of the directional distribution of acoustic intensity measured in a wind tunnel test of a crossflow jet and in a corresponding flight test.

Cole, J. E., III↗

Analysis of noise produced by an orderly structure of turbulent jets

The orderly structure which has been observed recently by numerous researchers within the transition region of subsonic turbulent jets is analyzed to reveal its noise-producing potential. For a circular jet, this structure is molded as a train of toroidal vortex rings which are formed near the jet exit and propagate downstream. The noise produced by the model is evaluated from a reformulation of Lighthill's expression for the far-field acoustic density, which emphasizes the importance of the vorticity within the turbulent flow field. It is shown that the noise production occurs mainly close to the jet exit and depends primarily upon temporal changes in the toroidal radii. The analysis suggests that the process of formation of this regular structure may also be an important contribution of the high-frequency jet noise. These results may be helpful in the understanding of jet-noise generation and in new approaches to jet-noise suppression.

Hardin, J. C.↗

An Analytical Investigation of Wing-Jet Interaction

The aerodynamic interaction between the wing and an inviscid jet with Mach number nonuniformity is formulated by using a two-vortex-sheet model for the jet. One of the vortex sheets accounts for the induced jet flow and the other the induced outer flow. No additional source distribution is needed for the jet at an angle of attack. The above problem is solved by satisfying the jet and wing tangency and the jet pressure-continuity conditions and using a quasi vortex lattice method for computing the induced flow field. The latter method is derived through theoretical consideration by properly accounting for singularities present in the equations and possesses the same simplicity and generality as the conventional vortex lattice method but has a better rate of numerical convergence. The resulting system of algebraic equations is solved by Purcell's vector method. The numerical formulation is first applied to the wing-slipstream interaction problem. Results for one centered-jet configuration are compared with those predicted by some existing theories.

Lan, E. C.↗

Turbulent wall jet in a coflowing stream

A theoretical investigation was undertaken to develop a relatively simple model of a two-dimensional, turbulent wall jet in a coflowing stream. The incompressible jet flow was modeled by using an integral method which includes turbulent shear stress, entrainment, and heat transfer. The method solves the conservation equations for the average jet flow properties and uses the velocity profile suggested by Escudier and Nicoll to obtain detailed characteristics of the jet on a flat plate. The analytical results compare favorably with experimental data for a range of injection velocities, which demonstrates the usefulness of the theory for estimating jet growth, velocity decay, and wall skin friction. The theory, which was applied to a Coanda jet on a circular cylinder, provided estimates of suction pressures aft of the jet exit that were in close agreement with experimental values.

Campbell, J. F.↗

Results of test MA22 in the NASA/LaRC 31-inch CFHT on an 0.010-scale model (32-0) of the space shuttle configuration 3 to determine RCS jet flow field interaction, volume 1

A wind tunnel test was conducted in the Langley Research Center 31-inch Continuous Flow Hypersonic Wind Tunnel from May 6, 1975 through June 3, 1975. The primary objectives of this test were the following: (1) to study the ability of the wind tunnel to repeat, on a run-to-run basis, data taken for identical configurations to determine if errors in repeatability could have a significant effect on jet interaction data, (2) to determine the effect of aerodynamic heating of the scale model on jet interaction, (3) to investigate the effects of elevon and body flap deflections on jet interaction, (4) to determine if the effects from jets fired separately along different axes can be added to equal the effects of the jets fired simultaneously (super position effects), (5) to study multiple jet effects, and (6) to investigate area ratio effects, i.e., the effect on jet interaction measurements of using wind tunnel nozzles with different area ratios in the same location. The model used in the test was a .010-scale model of the Space Shuttle Orbiter Configuration 3. The test was conducted at Mach 10.3 and a dynamic pressure of 150 psf. RCS chamber pressure was varied to simulate free flight dynamic pressures of 5, 7.5, 10, and 20 psf.

Kanipe, D. B.↗

On the effects of flight on jet engine exhaust noise

Recent flight data on jet engine exhaust noise do not agree with projections based on classical jet noise theories. This paper demonstrates that these differences may be reconciled by considering the combined effects of jet mixing noise and internally-generated engine exhaust noise. The source strength of the internally-generated noise is assumed to be unaffected by flight, as has been shown in small-scale free-jet experiments. The directivity of the internally-generated noise is assumed to be the same statically as that given in the NASA interim prediction method for core engine noise. However, it is assumed that in flight the internally generated noise is subject to the convective amplification effect of a simple source. The absolute levels of the internally-generated noise are obtained from an empirical fit of some typical engine data. The static and flight jet noise are predicted using the NASA interim prediction method for jet noise. It is shown that in many cases, although jet mixing may be the dominant noise source statically, much of the flyover noise signature is dominated by internally-generated noise.

Stone, J. R.↗

Comparison of aerodynamic theory and experiment for jet-flap wings

Aerodynamic theory predictions made for a jet flapped wing were compared with experimental data obtained in a fairly extensive series of tests in the Langley V/STOL tunnel. The tests were made on a straight, rectangular wing and investigated two types of jet flap concepts: a pure jet flap with high jet deflection and a wing with blowing at the knee of a plain trailing edge flap. The tests investigated full and partial span blowing for wing aspect ratios of 8.0 and 5.5 and momentum coefficients from 0 to about 4. The total lift, drag, and pitching moment coefficients predicted by the theory were in excellent agreement with experimental values for the pure jet flap, even with the high jet deflection. The pressure coefficients on the wing, and hence the circulation lift coefficients, were underpredicted, however, because of the linearizing assumptions of the planar theory. The lift, drag, and pitching moment coefficients, as well as pressure coefficients, were underpredicted for the wing with blowing over the flap because of the failure of the theory to account for the interaction effect of the high velocity jet passing over the flap.

Gainer, T. G.↗

On the use of relative velocity exponents for jet engine exhaust noise

The effect of flight on jet engine exhaust noise has often been presented in terms of a relative velocity exponent, n, as a function of radiation angle. The value of n is given by the OASPL reduction due to relative velocity divided by 10 times the logarithm of the ratio of relative jet velocity to absolute jet velocity. It is shown in this paper that the exponent n is positive for pure subsonic jet mixing noise and varies, in a systematic manner, as a function of flight conditions and jet velocity. On the basis of calculations from simple empirical models for jet mixing noise, shock noise and internally-generated noise, it is shown that when other sources are present, the resulting range of n is increased over the range for jet mixing noise, and in some cases negative values of n are obtained.

Stone, J. R.↗

Fluctuating surface pressure and acoustic radiation for subsonic normal jet impingement

Results are presented from an experimental study of fluctuating surface pressures and far-field noise produced by a subsonic circular jet impinging normally to a large, rigid, flat surface. The tests were performed in an anechoic room for jet Mach numbers from 0.54 to 0.85 and for jet-to-surface heights from 5 to 10 jet diameters. Space and time correlations of surface pressure indicated a radially spreading, decaying pressure field having correlation lengths on the order of one-half the jet diameter with convection speeds between 0.5 and 0.6 of the peak wall-jet velocity. Overall sound pressure level varied as the eighth power of the jet velocity. Large-scale orderly structures in the flow were suggested by the noise spectra which peaked at a Strouhal number of about 0.3. In addition, an analytical formulation was given to approximate the apparent noise-producing regions of the flow in terms of cross-correlations and cross-spectra between the surface and far-field measurements. Results pointed to the impingement region of the flow field as the major contribution to the far-field impingement noise.

Preisser, J. S.↗

An experimental study of the noise generating mechanisms in supersonic jets

Flow fluctuation measurements with normal and X-wire hot-wire probes and acoustic measurements with a traversing condenser microphone were carried out in small air jets in the Mach number range from M = 0.9 to 2.5. One of the most successful studies involved a moderate Reynolds number M = 2.1 jet. The large scale turbulence properties in the jet, and the noise radiation were characterized. A parallel study involved similar measurements on a low Reynolds number M = 0.9 jet. These measurements show that there are important differences in the noise generation process of the M = 0.9 jet in comparison with low supersonic Mach number (M = 1.4) jets. Problems encounted while performing X-wire measurements in low Reynolds number jets of M = 2.1 and 2.5, and in installing a vacuum pump are discussed.

Mclaughlin, D. K.↗

Heat transfer from a row of jets impinging on concave semi-cylindrical surface

Heat transfer from impinging jets has been analyzed. Based on similarities of the boundary conditions of the related flow fields, analogies between heat transfer from impinging jets at the stagnation point and in the wall jet region have been shown for several flow geometries. Calculation of heat transfer in the stagnation region and in the wall jet region, based on available theory and the parameters, obtained from direct measurements, have been carried out, for the single, round, impinging jets. It has been shown that heat transfer from a row of round jets impinging on flat and concave surfaces can be comprehensively described through analysis of impinging jets of simpler geometries. Finally, experimental results for the local and average heat transfer effects are presented and discussed. Comparisons are made with theory and results of other investigators, with fairly satisfactory agreement.

Hrycak, P.↗

An improved prediction method for the noise generated in flight by circular jets

A semi-empirical model for predicting the noise generated by jets exhausting from circular nozzles is presented and compared with small-scale static and simulated-flight data. The present method is an updated version of that part of the original NASA aircraft noise prediction program relating to circular jet noise. The earlier method agreed reasonably well with experimental static and flight data for jet velocities up to approximately 520 m/sec. The poorer agreement at higher jet velocities appeared to be due primarily to the manner in which supersonic convection effects were formulated. The purely empirical supersonic convection formulation is replaced in the present method by one based on theoretical considerations. Other improvements of an empirical nature were included based on model-jet/free-jet simulated-flight tests. The effects of nozzle size, jet velocity, jet temperature, and flight are included.

Stone, J. R.↗

Coannular jets - Are they really quiet and why

The noise reductions from both normal- and inverted-velocity-profile (IVP) shock-free coannular jets are critically assessed on the basis of existing data. The fully mixed equivalent (FMEQ) single jet, defined as having a uniform exit profile and the same thrust, mass flow rate and exit area as the coannular jet, is used throughout as the reference for noise comparisons. It is shown that uninverted-velocity-profile coannular jets are consistently noisier than FMEQ jets, whereas IVP jets are slightly quieter. The practical implications are discussed in detail. The 'inverted velocity' effects are isolated experimentally from the 'inverted temperature' effects and the resulting noise reductions or increases are explained by using the measurements of mean flow, turbulence structure, and source location in coannular jets.

Tanna, H. K.↗

Investigation of blown boundary layers with an improved wall jet system

Measurements were made in a two dimensional incompressible wall jet submerged under a thick upstream boundary layer with a zero pressure gradient and an adverse pressure gradient. The measurements included mean velocity and Reynolds stresses profiles, skin friction, and turbulence spectra. The measurements were confined to practical ratios (less than 2) of the jet velocity to the free stream velocity. The wall jet used in the experiments had an asymmetric velocity profile with a relatively higher concentration of momentum away from the wall. An asymmetric jet velocity profile has distinct advantages over a uniform jet velocity profile, especially in the control of separation. Predictions were made using Irwin's (1974) method for blown boundary layers. The predictions clearly show the difference in flow development between an asymmetric jet velocity profile and a uniform jet velocity profile.

Saripalli, K. R.↗

Jet array impingement with crossflow-correlation of streamwise resolved flow and heat transfer distributions

Correlations for heat transfer coefficients for jets of circular offices and impinging on a surface parallel to the jet orifice plate are presented. The air, following impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer (impingement) surface. The downstream jets are subjected to a crossflow originating from the upstream jets. Impingement surface heat transfer coefficients resolved to one streamwise jet orifice spacing, averaged across the channel span, are correlated with the associated individual spanwise orifice row jet and crossflow velocities, and with the geometric parameters.

Florschuetz, L. W.↗

Synchrotron brightness distribution of turbulent radio jets

Radio jets are considered as turbulent mixing regions and it is proposed that the essential small scale viscous dissipation in these jets is by emission of MHD waves and by their subsequent strong damping due, at least partly, to gyro-resonant acceleration of supra-thermal particles. A formula relating the synchrotron surface brightness of a radio jet to the turbulent power input is deduced from physical postulates, and is tested against the data for NGC315 and 3C31 (NGC383). The predicted brightness depends essentially on the collimation behavior of the jet, and, to a lesser extent, on the CH picture of a 'high' nozzle with accelerating flow. The conditions for forming a large scale jet at a high nozzle from a much smaller scale jet are discussed. The effect of entrainment on the prediction is discussed with the use of similarity solutions. Although entrainment is inevitably associated with the turbulent jet, it may or may not be a dominant factor depending on the ambient density profile.

Henriksen, R. N.↗

Prediction of jet exhaust noise on airframe surfaces during flight

The behavior of pressure fluctuations measured on the airframe of a prototype high lift jet transport (YC-14) is presented. The data are characterized in terms of a particular jet exhaust flow field idealization, jet mixing noise, and exhaust shock noise. Generalized spectrum shapes and scaling relations for peak level and frequency of peak level are developed, and the frequency is found to depend on jet exhaust velocity and aircraft velocity. Comparisons are made with near-field engine exhaust noise of a conventional jet, and results suggest that the same two exhaust noises are important for both aircraft types. Surface fluctuating pressure data are assessed, and results suggest that the jet mixing and exhaust shock noise source characterizations for the YC-14 have useful applicability to conventionally configured jets.

Butzel, L. M.↗