Instability Results for Cone-Cylinder-Flare and Cone-Flare Hypersonic Wind-Tunnel Configurations
Explore the source record for details and available documents.
Boundary Layer Transition↗
SEARCH · Engineering Papers
Results for “flow instability”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Polarization of the auroral electrojet
Precipitation from the inner edge of the electron plasma sheet creates a density maximum in the auroral oval ionosphere, which in turn leads to Hall and Pedersen conductance maxima. A uniform westward convection electric field is imposed upon the lower ionosphere previous to polarization. Field-aligned currents flow into the ionosphere equatorward, and out poleward, of the Hall conductance maximum. As the convection field and ionospheric density increase during substorm growth phase, the field-aligned current densities eventually reach an instability threshold, beyond which anomalous resistance produces field-aligned electric fields. The partial blockage of the field-aligned currents produces an equatorward electric field and therefore a partial Cowling conductivity in the lower ionosphere.
Coroniti, F. V.↗
Bars within bars - A mechanism for fuelling active galactic nuclei
A mechanism, applicable to AGN and nuclear starburst galaxies in which there is accretion onto a supermassive black hole (SBH), is proposed which brings in gas from large to small scales by successive dynamical instabilities. On the large scale, a stellar bar sweeps the interstellar medium into a gaseous disk a few hundred pc in radius. Under certain conditions, this disk can become unstable again, allowing material to flow inwards until turbulent viscous processes control angular-momentum transport. This flow pattern may feed viscosity-driven accretion flows around an SBH or lead to the formation of an SBH if none was present initially.
Shlosman, Isaac↗
Structure of a swirling turbulent mixing layer
A single-stream swirling turbulent mixing layer was produced in which the angular momentum instability acts over most of the layer for most of its development length. The instability is associated with a large increase in the level of the conventional Reynolds stresses over those in an unswirled mixing layer. This paper presents measurements of the three-dimensionality of the mean flow at one axial location well downstream of the origin. The output of a fixed hot-wire probe was ensemble-averaged to produce an approximation to the mean flow field that would be seen by a rotating observer. The main goals of this study were to establish the presence or absence of Taylor-Goertler vortices found in unstable laminar boundary layers. The variations in the mean velocities and Reynolds stresses are generally consistent with a bodily 'wrinkling' of the mixing layer, without a significant variation in the layer thickness. The wrinkling is most probably a result of circumferential variations in the initial boundary layer, which in turn originate at the swirl generator.
Wood, D. H.↗
The 3-D description of vertical current sheets with application to solar flares
Following a brief review of the processes which have been suggested for explaining the occurrence of solar flares we suggest a new scenario which builds on the achievements of the previous suggestion that the current sheets, which develop naturally in 3-D cases with gravity from impacting independent magnetic structures (i.e., approaching current systems), do not consist of horizontal currents but are instead predominantly vertical current systems. This suggestion is based on the fact that as the subphotospheric sources of the magnetic field displace the upper photosphere and lower chromosphere regions, where plasma beta is near unity, will experience predominantly horizontal mass motions which will lead to a distorted 3-D configurations of the magnetic field having stored free energy. In our scenario, a vertically flowing current sheet separates the plasma regions associated with either of the subphotospheric sources. This reflects the balanced tension of the two stressed fields which twist around each other. This leads naturally to a metastable or unstable situation as the twisted field emerges into a low beta region where vertical motions are not inhibited by gravity. In our flare scenario the impulsive energy release occurs, initially, not by reconnection but mainly by the rapid change of the magnetic field which has become unstable. During the impulsive phase the field lines contort in such way as to realign the electric current sheet into a minimum energy horizontal flow. This contortion produces very large electric fields which will accelerate particles. As the current evolves to a horizontal configuration the magnetic field expands vertically, which can be accompanied by eruptions of material. The instability of a horizontal current is well known and causes the magnetic field to undergo a rapid outward expansion. In our scenario, fast reconnection is not necessary to trigger the flare, however, slow reconnection would occur continuously in the current layer at the locations of potential flaring. During the initial rearrangement of the field strong plasma turbulence develops. Following the impulsive phase, the final current sheet will experience faster reconnection which we believe responsible for the gradual phase of the flare. The reconnection will dissipate part of the current and will produce sustained and extended heating in the flare region and in the postflare loops.
Fontenla, Juan M.↗
Some Effects of Tunnel Noise on Cylinder-Induced Mach 6 Transitional Shock Wave Boundary Layer Interactions
Experiments were conducted on a cylinder-induced shock wave boundary layer interaction (SBLI)as its state was brought through transition using a combination of boundary layer trips and Reynolds number sweep. A baseline case with no trips was also examined. The measurements were made in a Mach 6 freestream in the well-characterized Actively Controlled Expansion tunnel, which demonstrated a near tripling in fluctuation levels with unit Reynolds number increase from 3.0 to 3.5 million per meter. Surface oil flow and schlieren images suggested the jump in freestream noise served as the impetus for SBLI transition since the flow separation distance began to decrease as the Reynolds number progressed through those conditions. Likewise, surface mounted Kulite® pressure transducers indicated a rise in surface pressure fluctuations as well as initial growth in the instability responsible for transitioning the boundary layer within the interaction. Finally, heat transfer rates within the tripped SBLI were shown to be affected by the jump in freestream disturbance levels.
Andrew N Leidy↗
Parametric Inlet Tested in Glenn's 10- by 10-Foot Supersonic Wind Tunnel
The Parametric Inlet is an innovative concept for the inlet of a gas-turbine propulsion system for supersonic aircraft. The concept approaches the performance of past inlet concepts, but with less mechanical complexity, lower weight, and greater aerodynamic stability and safety. Potential applications include supersonic cruise aircraft and missiles. The Parametric Inlet uses tailored surfaces to turn the incoming supersonic flow inward toward an axis of symmetry. The terminal shock spans the opening of the subsonic diffuser leading to the engine. The external cowl area is smaller, which reduces cowl drag. The use of only external supersonic compression avoids inlet unstart--an unsafe shock instability present in previous inlet designs that use internal supersonic compression. This eliminates the need for complex mechanical systems to control unstart, which reduces weight. The conceptual design was conceived by TechLand Research, Inc. (North Olmsted, OH), which received funding through NASA s Small-Business Innovation Research program. The Boeing Company (Seattle, WA) also participated in the conceptual design. The NASA Glenn Research Center became involved starting with the preliminary design of a model for testing in Glenn s 10- by 10-Foot Supersonic Wind Tunnel (10 10 SWT). The inlet was sized for a speed of Mach 2.35 while matching requirements of an existing cold pipe used in previous inlet tests. The parametric aspects of the model included interchangeable components for different cowl lip, throat slot, and sidewall leading-edge shapes and different vortex generator configurations. Glenn researchers used computational fluid dynamics (CFD) tools for three-dimensional, turbulent flow analysis to further refine the aerodynamic design.
Slater, John W.↗
Boundary-Layer Instability Measurements in a Mach-6 Quiet Tunnel
Several experiments have been performed in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. A 7 degree half angle cone at 6 degree angle of attack with temperature-sensitive paint (TSP) and PCB pressure transducers was tested under quiet flow. The stationary crossflow vortices appear to break down to turbulence near the lee ray for sufficiently high Reynolds numbers. Attempts to use roughness elements to control the spacing of hot streaks on a flared cone in quiet flow did not succeed. Roughness was observed to damp the second-mode waves in areas influenced by the roughness, and wide roughness spacing allowed hot streaks to form between the roughness elements. A forward-facing cavity was used for proof-of-concept studies for a laser perturber. The lowest density at which the freestream laser perturbations could be detected was 1.07 x 10(exp -2) kilograms per cubic meter. Experiments were conducted to determine the transition characteristics of a streamwise corner flow at hypersonic velocities. Quiet flow resulted in a delayed onset of hot streak spreading. Under low Reynolds number flow hot streak spreading did not occur along the model. A new shock tube has been built at Purdue. The shock tube is designed to create weak shocks suitable for calibrating sensors, particularly PCB-132 sensors. PCB-132 measurements in another shock tube show the shock response and a linear calibration over a moderate pressure range.
Berridge, Dennis C.↗
Experiments on Ekman layer instability.
Instabilities of Ekman layer measured using hot- wire anemometers
EKMAN LAYER↗
The influence of a local wall deformation on the development of natural instabilities in a laminar boundary layer
The natural instabilities which propagate in the laminar boundary layer of a flat plate composed of intermittent wave trains are described. A spectral analysis determines the frequency range and gives a frequency and the harmonic 2 only if there is a wall deformation. This analysis provides the amplitude modulation spectrum of the instabilities. Plots of the evolution of power spectral density are compared with the numerical results obtained from the resolve of the Orr-Sommerfeld equation, while the harmonic is related to a micro-recirculating flow near the wall deformation.
Burnel, S.↗
Potential flow calculations and preliminary wing design in support of an NLF variable sweep transition flight experiment
NASA Langley and NASA Ames-Dryden have defined a variable-sweep transition-flight experiment utilizing the F-14 aircraft to enhance understanding of the interaction of crossflow and Tollmien-Schlichting instabilities on a laminar-boundary-layer transition. The F-14 wing outer panel will be modified to generate favorable pressure gradients on the upper wing surface over a wide range of flight conditions. Extensive computations have been performed using two-dimensional and three-dimensional transonic analysis codes. Flight-test and computational data are compared and shown to validate the applicability of the three-dimensional codes (WBPPW and TAWFIVE). In addition, results from two preliminary glove designs derived from two different approaches to the design problem are presented. Advantages and disadvantages of each approach are identified, and it is concluded that coupling an analysis code with an automated design procedure yields a powerful code with distinct advantages over a 'cut-and-dry' approach.
Waggoner, E. G.↗
Effect of acoustic excitation on stalled flows over an airfoil
The effect of acoustic excitation on post-stalled flows over an airfoil, i.e., flows that are fully separated from near the leading edge, is investigated. The excitation results in a tendency towards reattachment, which is accompanied by an increased lift and reduced drag, although the flow may still remain fully separated. It is found that with increasing excitation amplitude, the effect becomes more pronounced but shifts to a Strouhal number which is much lower than that expected from linear, inviscid instability of the separated shear layer.
Zaman, K. B. M. Q.↗
Effect of acoustic excitation on stalled flows over an airfoil
The effect of acoustic excitation on poststalled flows over an airfoil, i.e., flows that are fully separated from near the leading edge, is investigated. The excitation results in a tendency toward reattachment, which is accompanied by an increased lift and reduced drag, although the flow may still remain fully separated. It is found that with increasing excitation amplitude, the effect becomes more pronounced but shifts to a Strouhal number which is much lower than that expected from linear, inviscid instability of the separated shear layer.
Zaman, K. B. M. Q.↗
On the mechanism of turbulence suppression in free shear flows under acoustic excitation
Acoustic excitation at certain high frequencies has been known to suppress large amplitude fluctuations otherwise occurring naturally in various free shear flows. The phenomenon has been observed in flows with initially laminar or transitional boundary layers. An experimental investigation is conducted to consider two possibilities in regards to the mechanism of the effect. (1) The natural shear layer is self excited by the instability waves already developed in the upstream boundary layer. This is overridden when the shear layer is excited at its maximally unstable mode, causing the observed decrease in the intensities downstream. (2) The upstream boundary layer is in a transitional or buffeted laminar state, characterized by large amplitude unsteady fluctuations, which force the large fluctuations downstream. Excitation trips the upstream boundary layer to full turbulence, reduces the unsteady fluctuations, and thus causes the observed suppression of the intensities throughout the flowfield. The present experimental results refute either of these possibilities to be the general mechanism of the effect.
Zaman, K. B. M. Q.↗
On the mechanism of turbulence suppression in free shear flows under acoustic excitation
Acoustic excitation at certain high frequencies has been known to suppress large amplitude fluctuations otherwise occurring naturally in various free shear flows. The phenomenon has been observed in flows with initially laminar or transitional boundary layers. An experimental investigation is conducted to consider two possibilities in regards to the mechanism of the effect. (1) The natural shear layer is self excited by the instability waves already developed in the upstream boundary layer. This is overridden when the shear layer is excited at its maximally unstable mode, causing the observed decrease in the intensities downstream. (2) The upstream boundary layer is in a transitional or buffeted laminar state, characterized by large amplitude unsteady fluctuations, which force the large fluctuations downstream. Excitation trips the upstream boundary layer to full turbulence, reduces the unsteady fluctuations, and thus causes the observed suppression of the intensities throughout the flowfield. The present experimental results refute either of these possibilities to be the general mechanism of the effect.
Zaman, K. B. M. Q.↗
Interstellar clouds in high-speed, supersonic flows: Two-dimensional simulations
We present a series of gasdynamical simulations of the interaction of a dense, cool interstellar cloud with a high-speed, supersonic wind that confines and accelerates the embedded cloud. Our goal is to attempt to determine if such clouds can survive various potentially disruptive instabilities, that occur at their peripheries, long enough to be accelerated to speeds which are comparable to the wind velocity. These simulations are performed using two-dimensional, Eulerian gas dynamics on both an axisymmetric (about the cloud axis) and 'slab' geometric grid. The spatial and temporal resolutions of the simulations are varied over a wide range to investigate the effects of small-scale instabilities on the overall acceleration of clouds and the development of large-scale, disruptive instabilities. Also, we study the effects of wind/cloud Mach number variations by changing the wind speed constant at about 12 km/s (which corresponds to a cloud temperature of 10,000 K). The current simulations track the evolution of clouds as they are accelerated to speeds approximately 4-5 times greater than their internal sound speeds. Furthermore, the models with the highest resolution were extended far beyond quasi-linear Rayleigh-Taylor growth times reaching 6-7 Rayleigh-Taylor growth times for the largest scale instabilities before being terminated because of the accumulation of errors at the rear grid boundary.
Schiano, A. V. R.↗
A New Approach for Determining Onset of Transition
The final report consists of three papers which outline and demonstrate the new method for determining transition onset. The procedure developed under this grant requires specification of the instability mechanism, i.e., Tollmien-Schlichting or crossflow, that leads to transition. The attached papers are entitled: 'An Alternative to the e(sup n) Method for Determining Onset of Transition', 'Transition Model for Swept Wing Flows', and 'A Transition Closure Model for Predicting Transition Onset'.
Hassan, H. A.↗
Hypersonic Chemically Reacting Boundary-Layer Stability using LASTRAC
Hypersonic boundary layer transition is critical to the design of all hypersonic vehicles due to its effect on the heat transfer into the vehicle surface and potential drag enhancement or reduction during reentry. Boundary layer transition and boundary layer stability analysis under hypersonic conditions has been studied for decades, yet there is ample room for improved accuracy and further investigations into the relevant phenomena. In this work, we present a recent implementation of chemical equilibrium, finite-rate chemistry, and thermochemical nonequilibrium capabilities into LASTRAC, an existing well-established boundary-layer stability analysis code. Verification against existing numerical results in the literature are presented. LASTRAC was previously able to address calorically perfect flows. By using solutions of the Parabolized Stability Equations (PSE) with chemical and thermal nonequilibrium, we are able to investigate the effects of chemical and thermal nonequilibrium on a variety of phenomena including stationary crossflow instability on a swept wing and 2nd mode instabilities over a wedge.
Kline, H. L.↗