Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “distributed processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Initial Uncertainty Analysis of Carbon Tetrachloride Contamination and Remediation in the Ringold A and Lower Mud Units at the Central Plateau

The long-term effectiveness of groundwater cleanup at the Hanford Site Central Plateau depends on predictive models that can capture key uncertainties in contaminant fate and transport. Carbon tetrachloride (CCl 4 ), a persistent and toxic compound, presents particular challenges due to variability in degradation rates, uncertainty in initial plume distribution, and subsurface heterogeneity. These uncertainties directly influence plume persistence, migration pathways, and remedy performance, and thus must be systematically evaluated to support long-term remediation planning. To address these gaps, a large-scale Monte Carlo analysis was conducted using the Plateau to River (P2R) model framework. The modeling approach parameterized three primary uncertainty factors: (1) degradation rate, (2) initial plume distribution, and (3) hydraulic conductivity. Degradation was represented as a first-order process, with half-lives ranging from 70 to 700 years. Initial plume distributions were created using a geostatistical simulation method (sgsim), which generates many equally plausible versions of how contaminants might be distributed underground. From this, 100 different scenarios were mapped onto the P2R grid. Variability in hydraulic conductivity was represented in a similar way, with 100 scenarios each for the Ringold Lower Mud and Ringold A units (layers 6 and 7), based on fitted exponential variograms and conditioned to well data. In total, more than 1000 realizations were simulated to assess plume behavior under uncertainty. Results demonstrate that degradation kinetics exert the strongest control over plume persistence: Shorter half-lives produced rapid mass reduction, while longer half-lives yielded persistent plumes with limited attenuation. A nonlinear response was observed, with steep mass reductions at half-lives greater than 200 years and near-linear declines beyond this threshold, reflecting interactions between degradation and pumping. The initial plume distribution strongly influenced early transport patterns, with broader sources generating larger plume footprints, although pump-and-treat operations constrained plume migration to managed areas. By comparison, hydraulic conductivity variability in the Ringold units had only a secondary influence, modifying spreading behavior without altering the dominant migration pathways governed by source configuration and hydraulic controls. Overall, the analysis highlights that uncertainty in degradation rate and initial plume configuration are the primary drivers of variability in plume predictions, while conductivity heterogeneity plays a limited role. These findings underscore the need for improved site-specific data on degradation processes and source characterization to enhance the reliability of long-term performance assessments and to better inform remedial decision-making at the Central Plateau.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Working With Your Utility Series: Interconnection Basics

This training provided information on interconnection basics for federal agencies developing distributed energy projects. Considerations covered included: Understanding interconnection processes and timelines, interconnection siting considerations, technology-specific interconnection issues, and interconnect agreements. This webinar is the first in a multi-part series on working with electric utilities to develop distributed energy projects on federal sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Needle bacterial community structure across the species range of limber pine

Abstract Bacteria on and inside leaves can influence forest tree health and resilience. The distribution and limits of a tree species’ range can be influenced by various factors, with biological interactions among the most significant. We investigated the processes shaping the bacterial needle community across the species distribution of limber pine, a widespread Western conifer inhabiting a range of extreme habitats. We tested four hypotheses: (i) Needle community structure varies across sites, with site-specific factors more important to microbial assembly than host species selection; (ii) dispersal limitation structures foliar communities across the range of limber pine; (iii) the relative significance of dispersal and selection differs across sites in the tree species range; and (iv) needle age structures bacterial communities. We characterized needle communities from the needle surface and tissue of limber pine and co-occurring conifers across 16 sites in the limber pine distribution. Our findings confirmed that site characteristics shape the assembly of bacterial communities across the host species range and showed that these patterns are not driven by dispersal limitation. Furthermore, the strength of selection by the host varied by site, possibly due to differences in available microbes. Our study, by focusing on trees in their natural setting, reveals real needle bacterial dynamics in forests, which is key to understanding the balance between stochastic and deterministic processes in shaping forest tree-microbe interactions. Such understanding will be necessary to predict or manipulate these interactions to support forest ecosystem productivity or assist plant migration and adaptation in the face of global change.

59 BASIC BIOLOGICAL SCIENCES↗

Describing the Influence of Ball-milling on the Amorphization of Flubendazole Using the PDF and RMC Methods with X-ray Powder Diffraction Data

Flubendazole (FBZ) is a poorly water-soluble drug, and different methodologies have been proposed to improve its oral bioavailability. Obtaining the amorphous drug phase is an alternative to improve its water solubility. Several techniques for drug amorphization, such as spray drying, lyophilization, melt quenching, solvent-evaporation, and ball milling, can yield various types of structural disorder and possibly render variations in physicochemical properties. Herein, we focus on evaluating the influence of the ball-milling process on the amorphization of FBZ. The characterization of the average global and local structures before, during, and after the milling process is described by sequential Rietveld refinements, pair distribution function analysis, and the Reverse Monte Carlo method. In conclusion, we show that preserving the local structure (nearest molecules) can be responsible for avoiding the fast structure recrystallization commonly observed when using the solvent-evaporation process for the studied drug.

60 APPLIED LIFE SCIENCES↗

Using support vector machines for anomalous change detonation

We cast anomalous change detection as a binary classification problem, and use a support vector machine (SVM) to build a detector that does not depend on assumptions about the underlying data distribution. To speed up the computation, our SVM is implemented, in part, on a graphical processing unit. Results on real and simulated anomalous changes are used to compare performance to algorithms which effectively assume a Gaussian distribution. In this paper, we investigate the use of support vector machines (SVMs) with radial basis kernels for finding anomalous changes. Compared to typical applications of SVMs, we are operating in a regime of very low false alarm rate. This means that even for relatively large training sets, the data are quite meager in the regime of operational interest. This drives us to use larger training sets, which in turn places more of a computational burden on the SVM. We initially considered three different approaches to to address the need to work in the very low false alarm rate regime. The first is a standard SVM which is trained at one threshold (where more reliable estimates of false alarm rates are possible) and then re-thresholded for the low false alarm rate regime. The second uses the same thresholding approach, but employs a so-called least squares SVM; here a quadratic (instead of a hinge-based) loss function is employed, and for this model, there are good theoretical arguments in favor of adjusting the threshold in a straightforward manner. The third approach employs a weighted support vector machine, where the weights for the two types of errors (false alarm and missed detection) are automatically adjusted to achieve the desired false alarm rate. We have found in previous experiments (not shown here) that the first two types can in some cases work well, while in other cases they do not. This renders both approaches unreliable for automated change detection. By contrast, the third approach reliably produces good results, but at the cost of larger computational requirements caused by the need to estimate very small false alarm rates. To address these computational requirements, we employ a recently developed in-house solver for SVMs that is significantly faster than freely available standard solvers. But these computational issues are secondary to the larger question: do kernelized solutions provide better performance, in terms of detection rates and false alarm rates, than more traditional methods for change detection that effectively assume Gaussian data distributions? To this end, we will compare ROC curves obtained from the SVM with those from chronochrome, covariance equalization, and hyperbolic anomalous change detection.

97 MATHEMATICS AND COMPUTING↗

Comparing Measured Driver Behavior Distributions to Results from Car-Following Models using SUMO and Real-World Vehicle Trajectories from Radar: SUMO Default vs. Radar-Measured CF model Parameters

In this study, the physical principles governing car-following (CF) behavior and their impact on traffic flow at signalized intersections are investigated. High temporal-resolution radar data is used to provide valuable insights into actual CF behavior, including acceleration, deceleration, and time headway distribution. Demand-calibrated SUMO simulations are run using empirical CF parameter distributions, and three CF models are evaluated: IDM, EIDM, and Krauss. By emulating radar data in SUMO and processing simulated vehicle traces, discrepancies between empirical and simulated parameter distributions are identified. Further analysis includes comparisons with default SUMO CF model parameters. The findings reveal that measured accelerations differ from CF model parameter accelerations and using the empirical value ($\mu = 0.89m/s^2$) leads to unrealistic simulations that fail volume-based calibration. Default parameters for all three models reasonably approximate the mean and median of measured parameters, but fail to capture the true distribution shape, partly due to homogeneity when using default parameters. The results show that it is more effective to simulate with the default parameters provided by SUMO rather than using measurements of real-world distributions without additional calibration. Future work will investigate closing the loop between the measured real-world and SUMO distributions using traditional calibration tactics, as well as assess the impact of calibrated vs. default CF parameters on simulation outputs like fuel consumption.

Schrader, Max (ORCID:0000000336737672)↗

Elucidating the Effect of TiB{sub 2} Volume Percentage on the Mechanical Properties and Corrosion Behavior of Al5083-TiB{sub 2} Composites

Al5083-TiB{sub 2} in situ composites with 1, 3, and 5 volume percentages of TiB{sub 2} were fabricated. The effect of different volume percentages of TiB{sub 2} reinforcement particles on the mechanical properties and corrosion resistance of these composites was investigated. The hot extrusion process resulted in fragmentation and more homogeneous distribution of TiB{sub 2} particles throughout the Al5083 matrix. Also, the grain size reduced as the amount of TiB{sub 2} reinforcement particles increased which caused the improvement of both the strength and ductility of the material. It was shown that the hardness, the ultimate tensile strength (UTS), and the yield strength (YS) of both the as-cast and extruded materials increased with increasing TiB{sub 2} content. Also, TiB{sub 2} addition combined with the extrusion process improved both UTS and elongation (El.%) of the extruded structures which can be attributed to the presence of TiB{sub 2} particles and obtained microstructural refinement by hot extrusion process. However, the extruded Al5083-5 vol.% TiB{sub 2} composite showed lower ductility in comparison with the extruded Al5083-1 vol.% TiB{sub 2} and Al5083-3 vol.% TiB{sub 2} composites. Moreover, it could be concluded that the corrosion resistance and also the pitting corrosion behavior of the Al5083 alloy do not significantly change in the presence of TiB{sub 2} reinforcement particles.

36 MATERIALS SCIENCE↗

Unraveling structural evolution of LiNi 0.5 Mn 1.5 O 4 by in situ neutron diffraction

Here, we report that the electrochemical properties of the spinel LiNi 0.5 Mn 1.5 O 4 cathode material are influenced by the synthesis processes, which determines the impurity phase and the distribution of Ni and Mn in the spinel structure. Taking advantage of neutron's high sensitivity to Ni and Mn, in situ neutron diffraction has been employed to quantify the phase formation/structural evolution process under continuous heating/cooling and isothermal annealing conditions. The results show that the subtle Ni and Mn ordering process occurs slowly at 700 °C and the degree of ordering can be controlled by the annealing time. At temperatures above 750 °C, the LiNi 0.5 Mn 1.5 O 4 spinel phase starts to decompose into the rock-salt impurity phase accompanied by the release of O 2 . The rock-salt phase reverts back to the spinel phase upon cooling along with the oxygen uptake. In conclusion, the dynamic process of structural evolution of LiNi 0.5 Mn 1.5 O 4 that was unraveled by in situ neutron diffraction is valuable for guiding the synthesis of cathode materials with desirable properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Traveling Wave Relays for Distribution Feeder Protection with High Penetrations of Distributed Energy Resources

Increased penetration of power electronics interfaced Distributed Energy Resources (DER) like PV, electric vehicle and battery storage in the distribution system (both in numbers and sizes) may cause bi-directional power flows under normal operation. In addition, they contribute low fault current under short circuit conditions. These two changes can impact the proper operation of legacy protection systems. This can add additional challenges during weak grid and islanded operation. In this research, traveling wave (high frequency) signature based protection scheme is proposed for future distribution systems. Simulations are performed under different transient scenarios to provide insight into the high frequency signatures to show the traveling wave behavior. Finally, this paper discusses the importance of sensing and digital processing requirements for traveling-wave protection in distribution system.

41 EE - Solar Energy Technologies Office (EE-4S)↗

On the Path to SunShot - Emerging Issues and Challenges with Integrating High Levels of Solar into the Distribution System

Wide use of advanced inverters could double the electricity-distribution system’s hosting capacity for distributed PV at low costs—from about 170 GW to 350 GW (see Palmintier et al. 2016). At the distribution system level, increased variable generation due to high penetrations of distributed PV (typically rooftop and smaller ground-mounted systems) could challenge the management of distribution voltage, potentially increase wear and tear on electromechanical utility equipment, and complicate the configuration of circuit-breakers and other protection systems—all of which could increase costs, limit further PV deployment, or both. However, improved analysis of distribution system hosting capacity—the amount of distributed PV that can be interconnected without changing the existing infrastructure or prematurely wearing out equipment—has overturned previous rule-of-thumb assumptions such as the idea that distributed PV penetrations higher than 15% require detailed impact studies. For example, new analysis suggests that the hosting capacity for distributed PV could rise from approximately 170 GW using traditional inverters to about 350 GW with the use of advanced inverters for voltage management, and it could be even higher using accessible and low-cost strategies such as careful siting of PV systems within a distribution feeder and additional minor changes in distribution operations. Also critical to facilitating distributed PV deployment is the improvement of interconnection processes, associated standards and codes, and compensation mechanisms so they embrace PV’s contributions to system-wide operations. Ultimately SunShot-level PV deployment will require unprecedented coordination of the historically separate distribution and transmission systems along with incorporation of energy storage and “virtual storage,” which exploits improved management of electric vehicle charging, building energy systems, and other large loads. Additional analysis and innovation are neede

14 SOLAR ENERGY↗

Traveling Wave Relays for Distribution Feeder Protection with High Penetrations of Distributed Energy Resources: Preprint

Increased penetration of power electronics interfaced Distributed Energy Resources (DER) like PV, electric vehicle and battery storage in the distribution system (both in numbers and sizes) may cause bi-directional power flows under normal operation. In addition, they contribute low fault current under short circuit conditions. These two changes can impact the proper operation of legacy protection systems. This can add additional challenges during weak grid and islanded operation. In this research, traveling wave (high frequency) signature based protection scheme is proposed for future distribution systems. Simulations are performed under different transient scenarios to provide insight into the high frequency signatures to show the traveling wave behavior. Finally, this paper discusses the importance of sensing and digital processing requirements for traveling-wave protection in distribution system.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Traveling Wave Relays for Distribution Feeder Protection with High Penetrations of Distributed Energy Resources

Increased penetration of power electronics interfaced Distributed Energy Resources (DER) like PV, electric vehicle and battery storage in the distribution system (both in numbers and sizes) may cause bi-directional power flows under normal operation. In addition, they contribute low fault current under short circuit conditions. These two changes can impact the proper operation of legacy protection systems. This can add additional challenges during weak grid and islanded operation. In this research, traveling wave (high frequency) signature based protection scheme is proposed for future distribution systems. Simulations are performed under different transient scenarios to provide insight into the high frequency signatures to show the traveling wave behavior. Finally, this paper discusses the importance of sensing and digital processing requirements for traveling-wave protection in distribution system.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Nanoscale attraction between calcium-aluminosilicate-hydrate and Mg-Al layered double hydroxides in alkali-activated slag

Highlights: • Nanoscale structure of the intermixed Mg-Al LHD and C-S-H (I) in AAS is studied. • High-resolution STEM, FESEM, XRD are combined to characterize AAS. • New insights on the nanostructure of Mg-Al LHD and C-S-H (I) are provided. - Abstract: Calcium-aluminosilicate-hydrates (C-A-S-H) and Mg-Al layered double hydroxides (LDHs) are widely identified as the two main hydrated phases formed in alkali-activated slag (AAS), regardless of reactant composition. In addition to the precipitates of microscale crystals, Mg-Al LDHs can be intermixed particularly with the C-A-S-H in the inner product of AAS. This study aims at revealing the intermixing behaviors of C-A-S-H and Mg-Al LDH down to the nanometer scale using multiple advanced characterization techniques. The results show that the nanocrystalline C-A-S-H and Mg-Al LDH grains are thoroughly distributed in the background of an amorphous matrix. It is observed that Mg-Al LDH nanocrystalline grains with a size of about 15 to tens of nanometer strongly attach to the C-A-S-H nanocrystalline grains. The findings support the hypothesis that the positively-charged LDH layers are strongly attracted to the negatively-charged C-A-S-H layers during alkali-activation. This study contributes to a better understanding of the alkali-activated process as well as phase formation and distribution in this system.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Completion processing for data communications instructions

Completion processing of data communications instructions in a distributed computing environment with computers coupled for data communications through communications adapters and an active messaging interface (`AMI`), injecting for data communications instructions into slots in an injection FIFO buffer a transfer descriptor, at least some of the instructions specifying callback functions; injecting a completion descriptor for each instruction that specifies a callback function into an injection FIFO buffer slot having a corresponding slot in a pending callback list; listing in the pending callback list callback functions specified by data communications instructions; processing each descriptor in the injection FIFO buffer, setting a bit in a completion bit mask corresponding to the slot in the FIFO where the completion descriptor was injected; and calling by the AMI any callback functions in the pending callback list as indicated by set bits in the completion bit mask.

97 MATHEMATICS AND COMPUTING↗

Completion processing for data communications instructions

Completion processing of data communications instructions in a distributed computing environment with computers coupled for data communications through communications adapters and an active messaging interface (`AMI`), injecting for data communications instructions into slots in an injection FIFO buffer a transfer descriptor, at least some of the instructions specifying callback functions; injecting a completion descriptor for each instruction that specifies a callback function into an injection FIFO buffer slot having a corresponding slot in a pending callback list; listing in the pending callback list callback functions specified by data communications instructions; processing each descriptor in the injection FIFO buffer, setting a bit in a completion bit mask corresponding to the slot in the FIFO where the completion descriptor was injected; and calling by the AMI any callback functions in the pending callback list as indicated by set bits in the completion bit mask.

97 MATHEMATICS AND COMPUTING↗

Distributions of short-lived radioactive nuclei produced by young embedded star clusters

Most star formation in the Galaxy takes place in clusters, where the most massive members can affect the properties of other constituent solar systems. This paper considers how clusters influence star formation and forming planetary systems through nuclear enrichment from supernova explosions, where massive stars deliver short-lived radioactive nuclei (SLRs) to their local environment. The decay of these nuclei leads to both heating and ionization, and thereby affects disk evolution, disk chemistry, and the accompanying process of planet formation. Nuclear enrichment can take place on two spatial scales: (1) within the cluster itself (ℓ ∼ 1 pc), the SLRs are delivered to the circumstellar disks associated with other cluster members. (2) On the next larger scale (ℓ ∼ 2-10 pc), SLRs are injected into the background molecular cloud; these nuclei provide heating and ionization to nearby star-forming regions and to the next generation of disks. For the first scenario, we construct the expected distributions of radioactive enrichment levels provided by embedded clusters. Clusters can account for the SLR mass fractions inferred for the early Solar Nebula, but typical SLR abundances are lower by a factor of ∼10. For the second scenario, we find that distributed enrichment of SLRs in molecular clouds leads to comparable abundances. For both the direct and distributed enrichment processes, the masses of {sup 26}Al and {sup 60}Fe delivered to individual circumstellar disks typically fall in the range 10-100 pM {sub ☉} (where 1 pM {sub ☉} = 10{sup –12} M {sub ☉}). The corresponding ionization rate due to SLRs typically falls in the range ζ{sub SLR} ∼ 1-5 × 10{sup –19} s{sup –1}. This ionization rate is smaller than that due to cosmic rays, ζ{sub CR} ∼ 10{sup –17} s{sup –1}, but will be important in regions where cosmic rays are attenuated (e.g., disk mid-planes).

79 ASTRONOMY AND ASTROPHYSICS↗

Pore-scale simulation of multiphase flow and reactive transport processes involved in geologic carbon sequestration

Multiphase flow and reactive transport are two essential physicochemical processes that govern the effectiveness of geological carbon sequestration (GCS). The interaction and feedback among different phases and components during intricate physicochemical processes hold great significance in understanding CO 2 sequestration. Pore-scale simulations can account for multiphase flow and reactive transport processes in porous media and obtain spatial distributions of parameters (density, velocity, concentration, etc.) in the pore space as well as their temporal evolutions. This proves especially valuable considering that experiments can be hindered by constraints in spatial and temporal resolution. The comprehensive insights garnered from pore-scale research can be leveraged for continuum modeling using the representative elementary volume (REV) concept. In this contribution, four sequential mechanisms of CO 2 -brine-rock interaction in three zones delineated by CO 2 saturation are elaborated to elucidate complicated physicochemical processes involved in GCS, which are followed by general descriptions of mathematical equations and pore-scale numerical methods. In addition, as interested and commonly encountered processes, leakage risks during GCS and CO 2 -enhanced oil recovery (CO 2 -EOR) processes are presented. The existing challenges and future directions are discussed for both the performance of the pore-scale models and the current gaps in the field of GCS. Importantly, we expect that this review will prove beneficial for researchers interested in pore-scale simulations, GCS, and related disciplines.

58 GEOSCIENCES↗

DAMAGE MODELING OF INJECTION-MOLDED SHORT- AND LONG-FIBER THERMOPLASTICS

This article applies the recent anisotropic rotary diffusion – reduced strain closure (ARD-RSC) model for predicting fiber orientation and a new damage model for injection-molded long-fiber thermoplastics (LFTs) to analyze progressive damage leading to total failure of injection-molded long-glass-fiber/polypropylene (PP) specimens. The ARD-RSC model was implemented in a research version of the Autodesk Moldflow Plastics Insight (MPI) processing code, and it has been used to simulate injection-molding of a long-glass-fiber/PP plaque. The damage model combines micromechanical modeling with a continuum damage mechanics description to predict the nonlinear behavior due to plasticity coupled with damage in LFTs. This model has been implemented in the ABAQUS finite element code via user-subroutines and has been used in the damage analyses of tensile specimens removed from the injection-molded long-glass-fiber/PP plaques. Experimental characterization and mechanical testing were performed to provide input data to support and validate both process modeling and damage analyses. The predictions are in agreement with the experimental results.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗