Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Identification of strengthening phases in Al-Cu-Li alloy Weldalite (tm) 049

Microstructure property relationships were determined for a family of ultrahigh strength weldable Al-Cu-Li based alloys referred to as Weldalite (tm) alloys. The highest strength variant of this family, Weldalite 049, has a high Cu/Li wt pct. ratio with a nominal composition of Al-6.3Cu-1.3Li-0.4Ag-0.4Mg-0.14Zr. Increasing the alloy's lithium content above 1.3 wt pct. resulted in a decrease in both yield and ultimate tensile strength. Strength was shown to be strongly dependent on lithium content, with a maximum in strength occurring in the range of about 1.1 to 1.4 wt pct. lithium. The strengthening phases present in Weldalite 049 (1.3Li) and an Al-6.3Cu-1.9Li-0.4Mg-0.14Zr alloy were identified using transmission electron microscopy (TEM).

Source record↗
NASA NTRS1992

Combustion synthesis of advanced materials

The combustion synthesis of ceramic-metal composites using an in-situ liquid infiltration technique is described. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species i.e. solids, liquids and gases, with varying physical properties e.g. thermal conductivity, on the microstructure and morphology of synthesized products is also described. Alternatively, conducting the combustion synthesis reaction in a reactive gas environment is also discussed, in which advantages can be gained from the synergistic effects of combustion synthesis and vapor phase transport. In each case, the effect of the presence or absence of gravity (density) driven fluid flow and vapor transport is discussed as is the potential for producing new and perhaps unique materials by conducting these SHS reactions under microgravity conditions.

Moore, J. J.↗
DOE OSTI2025

Fused filament fabrication of thermoplastic polyurethane composites with microencapsulated phase-change material

Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.

25 ENERGY STORAGE↗
DOE OSTI2020

Impact of krypton irradiation on a single crystal tungsten: Multi-modal X-ray imaging study

Understanding microstructural and strain evolutions induced by noble gas production in the nuclear fuel matrix or plasma-facing materials is crucial for designing next generation nuclear reactors, as they are responsible for volumetric swelling and catastrophic failure. In this paper we describe a multimodal approach combining synchrotron-based nanoscale X-ray imaging techniques with atomic-scale electron microscopy techniques for mapping chemical composition, morphology and lattice distortion in a single crystal W induced by Kr irradiation. We report that Kr-irradiated single crystal W undergoes surface deformation, forming Kr containing cavities. Furthermore, positive strain fields are observed in Kr-irradiated regions, which lead to compression of underlying W matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Probing multiscale dissolution dynamics in natural rocks through microfluidics and compositional analysis

Mineral dissolution significantly impacts many geological systems. Carbon released by diagenesis, carbon sequestration, and acid injection are examples where geochemical reactions, fluid flow, and solute transport are strongly coupled. The complexity in these systems involves interplay between various mechanisms that operate at timescales ranging from microseconds to years. Current experimental techniques characterize dissolution processes using static images that are acquired with long measurement times and/or low spatial resolution. These limitations prevent direct observation of how dissolution reactions progress within an intact rock with spatially heterogeneous mineralogy and morphology. We utilize microfluidic cells embedded with thin rock samples to visualize dissolution with significant temporal resolution (100 ms) in a large observation window (3 × 3 mm). Here we injected acidic fluid into eight shale samples ranging from 8 to 86 wt % carbonate. The pre- and postreaction microstructures are characterized at the scale of pores (0.1 to 1 µm) and fractures (1 to 1,000 µm). We observe that nonreactive particle exposure, fracture morphology, and loss of rock strength are strongly dependent on both the relative volume of reactive grains and their distribution. Time-resolved images of the rock unveil the spatiotemporal dynamics of dissolution, including two-phase flow effects in real time and illustrate the changes in the fracture interface across the range of compositions. Moreover, the dynamical data provide an approach for characterizing reactivity parameters of natural heterogeneous samples when porous media effects are not negligible. The platform and workflow provide real-time characterization of geochemical reactions and inform various subsurface engineering processes.

58 GEOSCIENCES↗
DOE OSTI2021

Rate-dependent strength and deformation heterogeneity of B4C-reinforced Al composite: Time-resolved imaging with synchrotron X-rays

Dynamic (up to 5500 s -1 ) and quasi-static compression tests are conducted on a 15 wt% B4C particle-reinforced Al (B 4 C/Al) composite. In situ, high-speed synchrotron X-ray phase contrast imaging and digital image correlation are employed to map mesoscale deformation fields at μm and μs scales. The bulk stress–strain curves show significant strain and strain-rate hardening under dynamic compression. The strain-rate sensitivity exponent is an order of magnitude higher at high strain rates (> 10 3 s -1 ) than that at low strain rates (< 10 -2 s -1 ). Strain field mapping demonstrates distinct compressive strain localizations for both quasi-static and dynamic loading. Nevertheless, compressive strain localizations appear denser in spacing under dynamic loading, owing to spontaneous dislocation nucleation in both weak and strong zones. This results in a higher density of geometrically necessary dislocations, which contributes to the higher strain and strain-rate hardening of B 4 C/Al under dynamic loading. Additionally, the ratio of the maximum local strain to the bulk average is 1.5, and the local strain-rate enhancement cannot explain the increased rate sensitivity of B 4 C/Al under dynamic loading. Therefore, the rate-dependent deformation heterogeneity dominates the strain-rate hardening of B 4 C/Al. Postmortem analyses help correlate deformation features to particle- and grain-scale microstructures, yielding consistent results with mesoscale strain fields.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature effects of ion irradiation on the nanostructural features in ductile-phase-toughened tungsten composites

Ductile-phase toughened tungsten (DPT W) composites have emerged as promising candidates for load-bearing components behind the plasma-facing tungsten armor in fusion reactors due to their enhanced thermomechanical properties. This study focuses on a composite consisting of W particles embedded in a ductile NiFeW solution matrix, hot-rolled to a thickness reduction of 87% (87R DPT W). Sequential irradiations with Ni2+ and He+ ions were performed to identical doses and helium concentrations at room temperature (RT) and 1273 K. Irradiation at RT produced no discernible nanostructural features due to the immobility of mono-vacancies, whereas cavity formation was observed at 973 K. At 1273 K, the W phase exhibited larger cavities, reduced cavity number density, and lower volumetric swelling compared to 973 K. Notably, nanosized NiFeW precipitates formed within the W phase at 1273 K, a phenomenon absent at 973 K. A new phase of cubic (NiFe)6W6C was also observed at the interphase boundary. In contrast, the NiFeW matrix showed no nanostructural changes at 1273 K, likely due to cavity dissociation. Separate irradiations at 1273 K indicated that Ni2+ ions induced precipitate formation in the W phase, while He+ ions exclusively caused cavity formation. The microstructure of 87R DPT W irradiated at RT and subsequently annealed at 1273 K closely resembled that of material irradiated directly at 1273 K. Like oxide-dispersion-strengthened steels, the observed nanoparticle-embedded W can inhibit dislocation propagation, potentially delaying the ductile-to-brittle transition temperature. These findings highlight the potential of NiFeW nanoparticle-reinforced W composites as irradiation-resistant materials for fusion reactors.

Jiang, Weilin (ORCID:0000000183028313)↗
DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

La 2 Zr 2 O 7 Nanoparticle-Mediated Synthesis of Porous Al-Doped Li 7 La 3 Zr 2 O 12 Garnet

In this work, we modified the reaction pathway to quickly (minutes) incorporate lithium and stabilize the ionic conducting garnet phase by decoupling the formation of a La–Zr–O network from the addition of lithium. To do this, we synthesized La 2 Zr 2 O 7 (LZO) nanoparticles to which LiNO 3 was added. This method is a departure from typical solid-state synthesis methods that require high-energy milling to promote mixing and intimate particle–particle contact and from sol–gel syntheses as a unique porous microstructure is obtained. We show that the reaction time is limited by the rate of nitrate decomposition and that this method produces a porous high-Li-ion-conducting cubic phase, within an hour, that may be used as a starting structure for a composite electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Measuring the density, viscosity, and surface tension of molten titanates using electrostatic levitation in microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTi 2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ~10 mPa s near 2100 K to ~30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm -1 for the rare earth titanates and 383–395 dyn cm -1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. In conclusion, for solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

42 ENGINEERING↗
NASA NTRS1989

Mechanical and SEM analysis of artificial comet nucleus samples

Since 1987 experiments dealing with comet nucleus phenomena have been carried out in the DFVLR space simulation chambers. The main objective of these experiments is a better understanding of thermal behavior, surface phenomena and especially the gas dust interaction. As a function of different sample compositions and exposure to solar irradiation (xenon-bulbs) crusts of different hardness and thickness were measured. The measuring device consists of a motor driven pressure foot (5 mm diameter), which is pressed into the sample. The applied compressive force is electronically monitored. The microstructure of the crust and dust residuals is investigated by scanning electron microscopy (SEM) techniques. Stress-depth profiles of an unirradiated and an irradiated model comet are given.

Thiel, K.↗
NASA NTRS2003

Oxidation of ZrB2-and HfB2-Based Ultra-High Temperature Ceramics: Effects of Ta Additions

Several compositions of ZrB2- and HfB2-based Ultra-High Temperature Ceramics (UHTC) were oxidized in stagnant air at 1627 C in ten minute cycles for times up to 100 minutes. These compositions include: ZrB2 - 20v% SiC, HfB2 - 20v% SiC, ZrB2 - 20v% SiC - 20v% TaSi2, ZrB2 - 33v% SiC, HfB2 - 20v% SiC - 20v% TaSi2, and ZrB2 - 20v% SiC - 20v% TaC. The weight change due to oxidation was recorded. The ZrB2 - 20v% SiC - 20v% TaSi2 composition was also oxidized in stagnant air at 1927 C and in an arc jet atmosphere. Samples were analyzed after oxidation by x-ray diffraction, field emission scanning electron microscopy, and energy dispersive spectroscopy to determine the reaction products and to observe the microstructure. The ZrB2 - 20v% SiC - 20v% TaSi2 showed the lowest oxidation rate at 1627 C, but performed poorly under the more extreme tests due to liquid phase formation. Effects of Ta-additions on the oxidation of the diboride-based UHTC are discussed.

Opila, Elizabeth↗
NASA NTRS2004

Ceramic Interconnects with Low Sintering Temperature

Ceramic interconnects for use in solid oxide he1 cells are expected to operate between 900 to approximately 1000 C, sinter below 1400 C to allow co-firing and meet a number thermal mechanical requirements. The pervoskite type (ABO3) lanthanum chromite based materials have emerged as a leading candidate that will meet these criteria by varying the composition on the A and B sites. A need therefore exists to determine this material's temperature dependent electrical and mechanical properties with respect to these site substitutions. In this investigation oxide powders were prepared by the glycine-nitrate process. Ionic substitutions were carried out on A sites with Ca or Sr, and B sites with Co and Al, respectively. Only stoichiometric compositions were considered for the sake of stability. The powders and their ability to sinter were investigated by XRD, SEM, dilatometry and density measurements. The sintered materials were further examined by SEM, thermal expansion and electric conductivity measurements in order to elucidate the resulting microstructure, electrical and mechanical properties. In addition quantum mechanical calculations were performed to obtain insight into the effects of these dopants on the materials electronic band structure and lattice parameter.

Zhong, Zhi-Min↗
DOE OSTI2023

Reaction Current Heterogeneity at the Interface between a Lithium Electrode and Polymer/Ceramic Composite Electrolytes

Although lithium metal anodes are expected to increase the energy density of next-generation batteries, dendrite growth during charge remains a major bottleneck preventing widespread implementation. Composite solid electrolytes with ceramic particles embedded in a polymer matrix have the potential to prevent dendrites owing to the higher mechanical stiffness while also possessing the flexibility to maintain contact with the electrode. However, microscopically, the different mechanical and electrochemical properties of the polymer and ceramic domains can cause inhomogeneous charge transfer at the Li/electrolyte interface, which can lead to nonuniform Li deposition and propagation of dendrites. Here, we computationally examine the coupled electrochemical, transport, and mechanical processes at the interface to determine the propensity for dendrite formation and possible approaches to mitigate this issue. Predictions of two possible microstructures at the interface, namely, (i) where both the polymer and ceramic come in contact with Li metal and (ii) when only the polymer comes in contact with Li metal, suggest that the former has a greater tendency for nonuniform plating. In addition, predictions suggest that minimizing the interfacial resistance between polymers and ceramics and incorporating interlayers between the electrode and electrolyte help mitigate current heterogeneity. In conclusion, these predictions provide guidance for experimental approaches to prevent dendrites in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2024

Effect of Co on twin formation and magnetic properties of Sm(Fe,Ti,V) 12 alloys

Transferring the excellent intrinsic magnetic properties of SmFe 12 -based compounds to their extrinsic properties remains the main challenge in the development of high-performance SmFe12-based permanent magnets. Twin formation is one of the reasons for the inability to achieve high coercivity and remanence. Here we have shown that the addition of Co in Sm(Fe 1-x Co x ) 10–11 M 1–2 alloys, where M=Ti and V, leads to an increase in twin density. Microstructural characterizations revealed that the atomic arrangement in the twin boundary changes depending on the stabilizing element, which directly influences the local intrinsic magnetic properties. Theoretical investigations showed that the critical grain size at which twin formation can be hindered by grain size reduction decreases when the stabilizer changes from V to Ti. Furthermore, this study shows that the alloy composition influences not only the intrinsic magnetic properties but also the twin formation energy and its grain size dependence, crucial for the design of SmFe12-based permanent magnets.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Affordable, Robust Ceramic Joining Technology (ARCJoinT) Given 1999 R and D 100 Award

Advanced ceramics and fiber-reinforced ceramic matrix composites with high strength and toughness, good thermal conductivity, thermal shock resistance, and oxidation resistance are needed for high-temperature structural applications in advanced high-efficiency and high-performance engines, space propulsion components, and land-based systems. The engineering designs of these systems require the manufacturing of large parts with complex shapes, which are either quite expensive or impossible to fabricate. In many instances, it is more economical to build complex shapes by joining together simple geometrical shapes. Thus, joining has been recognized as an enabling technology for the successful utilization of advanced ceramics and fiber-reinforced composite components in high-temperature applications. However, such joints must retain their structural integrity at high temperatures and must have mechanical strength and environmental stability comparable to those of the bulk materials. In addition, the joining technique should be robust, practical, and reliable. ARCJoinT, which is based on the reaction-forming approach, is unique in terms of producing joints with tailorable microstructures. The formation of joints by this approach is attractive since the thermomechanical properties of the joint interlayer can be tailored to be very close to those of the base materials. In addition, high-temperature fixturing is not needed to hold the parts at the infiltration temperature. The joining process begins with the application of a carbonaceous mixture in the joint area, holding the items to be joined in a fixture, and curing at 110 to 120 C for 10 to 20 min. This step fastens the pieces together. Then, silicon or a silicon alloy in tape, paste, or slurry form is applied around the joint region and heated to 1250 to 1425 C (depending on the type of infiltrant) for 10 to 15 min. The molten silicon or silicon-refractory metal alloy reacts with carbon to form silicon carbide with controllable amounts of silicon and other phases as determined by the alloy composition. Joint thickness can be readily controlled through adjustments of the properties of the carbonaceous paste and the applied fixturing force. The photograph shows various shapes of silicon-carbide-based ceramics and fiberreinforced composites that have been joined using ARCJoinT. Thermomechanical and thermochemical characterization of joints is underway for a wide variety of silicon-carbidebased advanced ceramics and fiber-reinforced composites under the hostile environments that will be encountered in engine applications. ARCJoinT, which was developed by researchers at the NASA Glenn Research Center at Lewis Field, received R&D Magazine's prestigious R&D 100 Award in 1999.

Singh, Mrityunjay↗
DOE OSTI2023

High-Throughput Automated Exploration of Phase Growth Behaviors in Quasi-2D Formamidinium Metal Halide Perovskites

Quasi-2D metal halide perovskites (MHPs) are an emerging material platform for sustainable functional optoelectronics, but the uncontrollable, broad phase distribution remains a critical challenge for applications. Nevertheless, the basic principles for controlling phases in quasi-2D MHPs remain poorly understood, due to the rapid crystallization kinetics during the conventional thin-film fabrication process. In this work, a high-throughput automated synthesis-characterization-analysis workflow is implemented to accelerate material exploration in formamidinium (FA)-based quasi-2D MHP compositional space, revealing the early-stage phase growth behaviors fundamentally determining the phase distributions. Upon comprehensive exploration with varying synthesis conditions including 2D:3D composition ratios, antisolvent injection rates, and temperatures in an automated synthesis-characterization platform, it is observed that the prominent n = 2 2D phase restricts the growth kinetics of 3D-like phases—α-FAPbI 3 MHPs with spacer-coordinated surface—across the MHP compositions. Thermal annealing is a critical step for proper phase growth, although it can lead to the emergence of unwanted local PbI 2 crystallites. Additionally, fundamental insights into the precursor chemistry associated with spacer-solvent interaction determining the quasi-2D MHP morphologies and microstructures are demonstrated. The high-throughput study provides comprehensive insights into the fundamental principles in quasi-2D MHP phase control, enabling new control of the functionalities in complex materials systems for sustainable device applications.

2D perovskites↗
DOE OSTI2022

Depicting the roles of CuO secondary phase and heat treatment in driving the magnetic and magnetocaloric features of Pr 2/3 Sr 1/3 MnO 3 manganite

In this work, we report a detailed experimental study regarding the impact of copper oxide (CuO) secondary phase and heat treatments on the structural, magnetic, and magnetocaloric properties of the near-room temperature Pr 2/3 Sr 1/3 MnO 3 (PSMO) magnetic refrigerant. Our investigations are carried out by using structural and microstructural analyses, alongside magnetization measurements. Here, the analysis of X-ray diffraction data of PSMO(95%)-CuO(5%) (PSMO-CuO) samples shows the coexistence of both CuO and PSMO phases. Further, the microstructural analysis of PSMO-CuO reveals that the addition of CuO significantly enhances the grains size. On the other hand, the added secondary phase markedly reduces the Curie temperature (T c ) from 293 K for PSMO to about 273 K for PSMO-CuO composite while increasing the magnetocaloric effect. This decrease in T c is associated with a significant change from 162° to about 156° in the Mn-OII-Mn bond angle respectively. Moreover, performed investigations regarding the role of heat treatments unveil that the observed changes in the structural and magnetic features are mainly driven by the secondary phase that modify grains size and double-exchange interactions in the PSMO compound. Interestingly, our findings demonstrate that the Curie temperature of the PSMO and accordingly its magnetocaloric effect can be tailored by adding small amounts of CuO without need to substitution on cation sites. In the light of obtained results, a multilayered refrigerant composed of PSMO and PSMO-CuO is proposed to cover the magnetic cooling temperature range close to room-temperature. The resulting entropy change remains practically constant between 273 K and 293 K. Such a behavior is highly appreciated from a practical point of view, particularly in cases where the cooling process is carried out by using the AMR and Ericsson cycles.

36 MATERIALS SCIENCE↗