Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Hydrogen titanate nanotubes for dye sensitized solar cells applications: Experimental and theoretical study

Highlights: • Photoelectrode made of Hydrogen titanate nanotubes from H{sub 2}Ti{sub 3}O{sub 7}. • Solar cell efficiency enhancement from 5.95% to 7.63%. • Increase of Voc due to a decrease in the work function on HTNT. • Increase of Jsc due to an increase of the specific area of HTNT. - Abstract: The existent research literature of Dye Sensitized Solar Cells (DSSC) is mainly focused on the dye but there are very few studies focused in the semiconductor. Here, we present the performance of hydrogen titanate nanotubes (HTNT), showing an enhancement of the solar cell efficiency from 5.95% to 7.63%, respect to anatase as photoelectrode. This enhancement could be explained in terms of open-circuit voltage, directly associated to the value of the HTNT band gap (E{sub g} = 3.3 eV), the relative position of the edge conduction band; and the increase of the short-circuit current, directly associated to the enhancement of the specific area of the photoelectrode. All these characteristics are in very good concordance with our theoretical modelling of the system, based on First Principles calculations. We expect that this system could be further characterized, utilizing different dyes or absorbers, in order to evaluate the potential use of hydrogen titanate nanotubes for solar cell applications.

14 SOLAR ENERGY↗

Device Architecture and Lifetime Requirements for High Efficiency Multicrystalline Silicon Solar Cells

We present a numerical simulation study of different multicrystalline silicon materials and solar cell architectures to understand today's efficiency limitations and future efficiency possibilities. We compare conventional full-area BSF and PERC solar cells to future cell designs with a gallium phosphide heteroemitter. For all designs, mc-Si materials with different excess carrier lifetime distributions are used as simulation input parameters to capture a broad range of materials. The results show that conventional solar cell designs are sufficient for generalized mean lifetimes between 40 – 90 μs, but do not give a clear advantage in terms of efficiency for higher mean lifetime mc-Si material because they are often limited by recombination in the phosphorus diffused emitter region. Heteroemitter designs instead increase in cell efficiency considerable up to generalized mean lifetimes of 380 μs because they are significantly less limited by recombination in the emitter and the bulk lifetime becomes more important. In conclusion, to benefit from increasing mc-Si lifetime, new cell designs, especially heteroemitter, are desirable.

14 SOLAR ENERGY↗

Record breaking solar cells: Zn x Cd( 1-x )Te graded bandgap nanoarrays

CdTe is the leading material for thin-film solar cells due to ease of processing and reduced cost. However, low conversion efficiencies due to defects in the material are still a problem in these devices. We propose implementing micro and nano-enabled pseudomorphic growth of ZnCdTe to dramatically increase the efficiency of CdTe solar cells. Simulations predict that defect-free films are possible in graded ZnCdTe nanoislands below 90 nm as well as 24 % efficient solar cells with the use of ZnCdTe grading. Selective growth of CdTe showed single grains when the island sizes decreased below 300 nm. The simulation and experimental results demonstrate for the first time the ability to use nanopatterned substrates to enhance uniformity and efficiency in CdTe thin film solar cells. More than 20 reports, presentations, and papers were produced as part of this work and the results from this project enabled UTEP and Sandia to secure to grants.

Cruz-Campa, Jose Luis↗

All-Carbon Nanotube Solar Cell Devices Mimic Photosynthesis

We report that both solar cells and photosynthetic systems employ a two-step process of light absorption and energy conversion. In photosynthesis, they are performed by distinct proteins. However, conventional solar cells use the same semiconductor for optical absorption and electron-hole separation, leading to inefficiencies. Here, we show that an all-semiconducting single-walled carbon nanotube (s-SWCNTs) device provides an artificial system that models photosynthesis in a tandem geometry. We use distinct chirality s-SWCNTs to separate the site and direction of light absorption from those of power generation. Using different bandgap s-SWCNTs, we implement an energy funnel in dual-gated p-n diodes. The device captures photons from multiple regions of the solar spectrum and funnels photogenerated excitons to the smallest bandgap s-SWCNT layer, where they become free carriers. We demonstrate an increase in the photoresponse by adding more s-SWCNT layers of different bandgaps without a corresponding deleterious increase in the dark leakage current.

14 SOLAR ENERGY↗

Operation Mechanism of Perovskite Quantum Dot Solar Cells Probed by Impedance Spectroscopy

We fabricated perovskite quantum dot solar cells (PQDSCs) and varied the thickness of the QD layer by controlling the number of deposition cycles; the cells were systematically investigated with impedance spectroscopy. Despite the evident structural differences with respect to standard perovskite solar cells (PSCs), similar impedance spectra were obtained for PQDSCs, pointing to similar working principles in terms of the active layer. We distinguish two different regimes: At low illumination, recombination is ruled by multiple trapping with trap distributions and/or shunting. However, at higher light intensities, Shockley-Read-Hall recombination is observed. In addition, the low-frequency capacitance, CLF, of PQDSCs increases several orders of magnitude when the illumination is varied from dark to 1-sun conditions. This feature has not been observed in other kinds of photovoltaic devices and is characteristic of PSCs. Although there is no consensus about the exact mechanism responsible for CLF, the suggested models point to an ion migration origin. Its observation in thin-film and PQDSCs devices implies a similar effect in both.

14 SOLAR ENERGY↗

Demonstration of GaInP2/Si Voltage Matched Tandem Solar Cells

Mechanically-stacked tandem solar cells combining existing photovoltaic technologies present a straightforward path toward higher conversion efficiencies. Voltage-matched configurations have been proposed as a simplified approach for fabricating two terminal modules, but they are subject to performance losses compared to four terminal configurations if voltage-matching conditions are not met. Here, we demonstrate a two terminal voltage-matched GaInP 2 /Si tandem with 23% efficiency. Through a combination of experimental measurement and simulation, we explore the impact of voltage and fill factor mismatches between the top and bottom sub-cell strings. Our results show that efficiency losses are minimized when voltage-mismatches are accommodated by designing the bottom strings to have a higher voltage. Fill factor mismatches due to differences in series resistance also lead to changes in the optimal ratio of the number of cells in the top and bottom sub-cell strings.

14 SOLAR ENERGY↗

Current enhancement of CdTe-based solar cells

We report on the realization of CdTe solar cell photocurrent enhancement using an n-type CdSe heterojunction partner sputtered on commercial SnO 2 /SnO 2 :F coated soda-lime glass substrates. With high-temperature close-space sublimation CdTe deposition followed by CdCl 2 activation, this thin-film stack allows for substantial interdiffusion at the CdSe/CdTe interface facilitating a CdSe x Te 1-x alloy formation. The bowing effect causes a reduced optical bandgap of the alloyed absorber layer and, therefore, leads to current enhancement in the long-wavelength region and a decrease in open-circuit voltage (V OC ). To overcome the V OC loss and maintain a high short-circuit current (J SC ), the CdTe cell configuration has been modified using combined CdS:O/CdSe window layers. The new device structure has demonstrated enhanced collection from both short-and long-wavelength regions as well as a V OC improvement. With an optimized synthesis process, a small-area cell using CdS:O/CdSe window layer showed an efficiency of 15.2% with a V OC of 831 mV, a J SC of 26.3 mA/cm 2 , and a fill factor of 69.5%, measured under an AM1.5 illumination without antireflection coating. Furthermore, the results provide new directions for further improvement of CdTe-based solar cells.

14 SOLAR ENERGY↗

Improved Energy Conversion Efficiency in Wide Bandgap Cu(In,Ga)Se2 Solar Cells

This report outlines improvements to the energy conversion efficiency in wide bandgap (E{sub g} > ;1.2 eV) solar cells based on CuIn{sub 1-x}Ga{sub x}Se{sub 2}. Using (a) alkaline containing high temperature glass substrates, (b) elevated substrate temperatures 600 C-650 C and (c) high vacuum evaporation from elemental sources following NREL's three-stage process, we have been able to improve the performance of wider bandgap solar cells with 1.2 < E{sub g} < 1.45 eV. Initial results of this work have led to efficiencies >18% for absorber bandgaps {approx}1.30 eV and efficiencies {approx}16% for bandgaps up to {approx}1.45 eV. In comparing J-V parameters in similar materials, we establish gains in the open-circuit voltage and, to a lesser degree, the fill factor value, as the reason for the improved performance. The higher voltages seen in these wide gap materials grown at high substrate temperatures may be due to reduced recombination at the grain boundary of such absorber films. Solar cell results, absorber materials characterization, and experimental details are reported.

14 SOLAR ENERGY↗

Alternative Rear Contacts for Ultrathin CdSexTe1-x Solar Cells

The back contact is a key component for further developments of CdSeTe solar cells. In this contribution, we investigate several materials and designs that could help the development of highly-reflective, ohmic back contacts for conventional (3.45 um) and thin (800 nm) CdSeTe solar cells. We also explore numerically, nanostructured metal back contacts for light-trapping in ultrathin (200 nm) CdTe solar cells.

back contact↗

In-Operando Characterization of P-I-N Perovskite Solar Cell Under Reverse Bias

A solar module is often exposed to a variety of intensity and uniformity illumination conditions throughout a day. In the field, objects or dirt can block light from hitting the module creating a partial shading event. When a partial shading event occurs the module power point tracking system will typically push the shaded cells into reverse bias in order to avoid the current loss from the other series connected illuminated cells. When perovskite solar cells are operated in reverse bias, electrochemical reactions can occur, leading to both reversible and irreversible performance losses. Excess holes generated by reverse bias cause and push the oxidation reaction of halide ions from the lattice to neutral halogen interstitial. Small interstitial halogen atoms can diffuse across the device and potentially move from the perovskite layer and into the transport layers, shifting the fermi levels in the devices. In this investigation we utilize cross-sectional kelvin probe atomic force microscopy to map the band energetics of perovskite solar cells during reverse bias. We observe a 150 meV decrease in the work function of the C 60 . This leads to a decrease of 150 mV and 4 mA/cm 2 in V oc and in J sc respectively. Finally, we discuss methods to prevent this irreversible degradation after a perovskite device is held under reverse bias.

fullerene↗

Low cost back contact heterojunction solar cells on thin c-Si wafers. Integrating laser and thin film processing for improved manufacturability

An interdigitated back contact (IBC) Si wafer solar cell with deposited a-Si heterojunction (HJ) emitter and contacts is considered the ultimate single junction Si solar cell design. This was confirmed in 2014 by both Panasonic and Sharp Solar producing IBC-HJ cells breaking the previous record Si solar cell efficiency of 25%. But manufacturability at low cost is a concern for the complex IBC-HJ device structure. In this research program, our goals were to addressed the broad industry need for a high-efficiency c-Si cell that overcomes the dominant module cost barriers by 1) developing thin Si wafers synthesized by innovative, kerfless techniques; 2) integrating laser-based processing into most aspects of solar cell fabrication, ensuring high speed and low thermal budgets ; 3) developing an all back contact cell structure compatible with thin wafers using a simplified, low-temperature fabrication process; and 4) designing the contact patterning to enable simplified module assembly. There were a number of significant achievements from this 3 year program. Regarding the front surface, we developed and applied new method to characterize critical interface recombination parameters including interface defect density Dit and hole and electron capture cross-section for use as input for 2D simulation of the IBC cell to guide design and loss analysis. We optimized the antireflection and passivation properties of the front surface texture and a-Si/a-SiN/a-SiC stack depositions to obtain a very low (< 6 mA/cm2) front surface optical losses (reflection and absorption) while maintaining excellent surface passivation (SRV<5 cm/s). We worked with kerfless wafer manufacturers to apply defect-engineering techniques to improve bulk minority-carrier lifetime of thin kerfless wafers by both reducing initial impurities during growth and developing post-growth gettering techniques. This led insights about the kinetics of nickel, chromium, and dislocations in PV-grade silicon and to achieving millisecond lifetimes in kerfless silicon materials. Laser fired contacts to n-Si were developed for the first time using a Al/Sb/Ti metal stack giving contact resistances < 5 mOhm-cm2 when fired through several different dielectric layers. A new 2 step laser+chemical etch isolation technique was developed using a sacrificial top coating which avoids laser damage to Si passivation. Regarding the heterojunction emitter, analysis of front FHJ (1D) and IBC (2D) cells with range of p-layer conditions found that a 2-stage high/low doped p-layer was optimum: the low doped region has lower defects giving higher Voc and the high doped region gave a better contact to the metal. A significant effort was spent studying the patterning process and its contribution to degradation of passivation and reproducibility. Several promising new cleaning, contact and deposition patterning and processing approaches were implemented leading to fabrication of several runs with cells having 19-20% efficiency which were stable over several months. This program resulted in the training and support of 12 graduate students, publication of 21 journal papers and 14 conference papers.

14 SOLAR ENERGY↗

Dopant ink composition and method of fabricating a solar cell there from

Dopant ink compositions and methods of fabricating solar cells there from are described. A dopant ink composition may include a cross-linkable matrix precursor, a bound dopant species, and a solvent. A method of fabricating a solar cell may include delivering a dopant ink composition to a region above a substrate. The dopant ink composition includes a cross-linkable matrix precursor, a bound dopant species, and a solvent. The method also includes baking the dopant ink composition to remove a substantial portion of the solvent of the dopant ink composition, curing the baked dopant ink composition to cross-link a substantial portion of the cross-linkable matrix precursor of the dopant ink composition, and driving dopants from the cured dopant ink composition toward the substrate.

14 SOLAR ENERGY↗

Dopant ink composition and method of fabricating a solar cell there from

Dopant ink compositions and methods of fabricating solar cells there from are described. A dopant ink composition may include a cross-linkable matrix precursor, a bound dopant species, and a solvent. A method of fabricating a solar cell may include delivering a dopant ink composition to a region above a substrate. The dopant ink composition includes a cross-linkable matrix precursor, a bound dopant species, and a solvent. The method also includes baking the dopant ink composition to remove a substantial portion of the solvent of the dopant ink composition, curing the baked dopant ink composition to cross-link a substantial portion of the cross-linkable matrix precursor of the dopant ink composition, and driving dopants from the cured dopant ink composition toward the substrate.

14 SOLAR ENERGY↗

Ultra-thin GaAs single-junction solar cells integrated with a reflective back scattering layer

This paper reports the proposal, design, and demonstration of ultra-thin GaAs single-junction solar cells integrated with a reflective back scattering layer to optimize light management and minimize non-radiative recombination. According to our recently developed semi-analytical model, this design offers one of the highest potential achievable efficiencies for GaAs solar cells possessing typical non-radiative recombination rates found among commercially available III-V arsenide and phosphide materials. The structure of the demonstrated solar cells consists of an In{sub 0.49}Ga{sub 0.51}P/GaAs/In{sub 0.49}Ga{sub 0.51}P double-heterostructure PN junction with an ultra-thin 300 nm thick GaAs absorber, combined with a 5 μm thick Al{sub 0.52}In{sub 0.48}P layer with a textured as-grown surface coated with Au used as a reflective back scattering layer. The final devices were fabricated using a substrate-removal and flip-chip bonding process. Solar cells with a top metal contact coverage of 9.7%, and a MgF{sub 2}/ZnS anti-reflective coating demonstrated open-circuit voltages (V{sub oc}) up to 1.00 V, short-circuit current densities (J{sub sc}) up to 24.5 mA/cm{sup 2}, and power conversion efficiencies up to 19.1%; demonstrating the feasibility of this design approach. If a commonly used 2% metal grid coverage is assumed, the anticipated J{sub sc} and conversion efficiency of these devices are expected to reach 26.6 mA/cm{sup 2} and 20.7%, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ternary Organic Solar Cells with Minimum Voltage Losses

Abstract A new strategy for designing ternary solar cells is reported in this paper. A low‐bandgap polymer named PTB7‐Th and a high‐bandgap polymer named PBDTTS‐FTAZ sharing the same bulk ionization potential and interface positive integer charge transfer energy while featuring complementary absorption spectra are selected. They are used to fabricate efficient ternary solar cells, where the hole can be transported freely between the two donor polymers and collected by the electrode as in one broadband low bandgap polymer. Furthermore, the fullerene acceptor is chosen so that the energy of the positive integer charge transfer state of the two donor polymers is equal to the energy of negative integer charge transfer state of the fullerene, enabling enhanced dissociation of all polymer donor and fullerene acceptor excitons and suppressed bimolecular and trap assistant recombination. The two donor polymers feature good miscibility and energy transfer from high‐bandgap polymer of PBDTTS‐FTAZ to low‐bandgap polymer of PTB7‐Th, which contribute to enhanced performance of the ternary solar cell.

Wang, Chuanfei↗

Molecular interactions that drive morphological and mechanical stabilities in organic solar cells

Morphological and mechanical stabilities of organic solar cells (OSCs) are of paramount importance to ensure long-lived devices. However, the fundamental drivers of these stability metrics and their competing relationship have yet to be well defined. Here, in this work, several high-performance polymers and small molecule acceptors (SMAs) are considered to assist in the development of a comprehensive view of the molecular drivers of, and interrelationships between, morphological and mechanical stabilities. We find that the SMAs drive much of the embrittlement and diffusion characteristics in the blend films. However, the heterointeraction of the SMA and polymer, probed through dynamic mechanical analysis, is a key contributing factor to the film toughness. The heterointeraction energy is ideally maximally negative (i.e., repulsive), deviating from the geometric mean of the homointeraction energy. These findings assist in introducing a framework to understand the active layer stability and highlight material properties that lead to morphologically stable and physically robust OSCs.

14 SOLAR ENERGY↗

Laser processing of solar cells with anti-reflective coating

Contact holes of solar cells are formed by laser ablation to accommodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thicknesses.

14 SOLAR ENERGY↗

Characterization of deliberately nickel-doped silicon wafers and solar cells

Microstructural and electrical evaluation tests were performed on nickel-doped p-type silicon wafers before and after solar cell fabrication. The concentration levels of nickel in silicon were 5 x 10 to the 14th power, 4 x 10 to the 15th power, and 8 x 10 to the 15th power atoms/cu cm. It was found that nickel precipitated out during the growth process in all three ingots. Clumps of precipitates, some of which exhibited star shape, were present at different depths. If the clumps are distributed at depths approximately 20 micron apart and if they are larger than 10 micron in diameter, degradation occurs in solar cell electrical properties and cell conversion efficiency. The larger the size of the precipitate clump, the greater the degradation in solar cell efficiency. A large grain boundary around the cell effective area acted as a gettering center for the precipitates and impurities and caused improvement in solar cell efficiency. Details of the evaluation test results are given.

Salama, A. M.↗