Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reacting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Acid–base concentration swing for direct air capture of carbon dioxide

This work demonstrates the first experimental evidence of the acid–base concentration swing (ABCS) for direct air capture of CO 2 . This process is based on the effect that concentrating particular acid–base chemical reactants will strongly acidify solution, through Le Chatelier's principle, and result in outgassing absorbed CO 2 . After collecting the outgassed CO 2 , diluting the solution will result in a reversal of the acid–base reaction, basifying the solution and allowing for atmospheric CO 2 absorption. The experimental study examines a system that includes sodium cation as the alkalinity carrier, boric acid, and a polyol complexing agent that reversibly reacts with boric acid to strongly acidify solution upon concentration. Though the tested experimental system faces absorption rate and water capacity limitations, the ABCS process described here provides a basis for further process optimization. A generalized theoretical ABCS reaction framework is developed and different reaction orders and conditions are studied mathematically. Higher order reactions yield favorable cycle output results, reaching volumetric cycle capacity above 50 mM for third-order and 80 mM for fourth-order reactions. Optimal equilibrium constants are determined in order to guide alternative chemical searches and synthetic chemistry design targets. There is a substantial energetic benefit for reaction orders above the first, with second- and third-order ABCS cycles exhibiting a thermodynamic minimum work for the concentrating and outgassing steps around 150 kJ per mole of CO 2 . A significant advantage of the ABCS is that it can be driven through well-developed and widely-deployed desalination technologies, such as reverse osmosis, with opportunities for energy recovery when recombining the concentrated and diluted streams, and extraction can occur directly from the liquid phase upon vacuum application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Direct measurements for the kinetics of C–C bond fission in the high temperature decomposition of isopropanol

The thermal decomposition of isopropanol was studied experimentally and theoretically with a view to isolate and directly measure rate coefficients for the dominant radical channel in this multi-channel process. Two complementary shock tube methods, laser schlieren densitomtery and H-atom atomic resonance absorption spectroscopy, were used to obtain rate coefficents for the C–C bond fission channel. The experimental ranges span temperatures from 1200–2100 K and pressures between 30–690 torr. These are the most direct measurements of this rate coefficent in the fall-off regime of relevance to high-temperature reacting systems. Theoretical studies also performed in this work confirm that the title reaction and a molecular elimination involving dehydration were the sole unimolecular processes at high temperatures. A master equation analysis yielded k ( T, P ) for the C–C fission and these are shown to be in good agreement with the present experimental measurements. Comparisons with prior experimental and theoretical studies in the literature indicate branching ratios as well as absolute k ( T, P ) for C–C bond-fission have been under-predicted for this decomposition reaction. Consequently, results from the present studies place an increased emphasis on radical-driven secondary processes in high-temperature pyrolysis of this simplest secondary alcohol.

Kim, John H. [Univ. of Michigan, Ann Arbor, MI (Un↗

Gas-phase negative ion photoelectron spectroscopy and reactivity of phenylacetylide

Arylacetylides such as phenylacetylide (PhCC–, 1) are important nucleophiles used in synthetic chemistry yet rarely have they been studied as bare carbanions. In this work, the phenylacetylide anion was formed via electrospray ionization (ESI) or multistage mass spectrometry (MSn) experiments and subsequently examined in the gas phase by negative ion photoelectron spectroscopy (NIPES), ion-molecule reactions (IMR), alongside theoretical calculations to probe its fundamental structure and reactivity. Photoelectron spectra of PhCC– (1) revealed vertical (VDE) and adiabatic detachment energies (ADE), both of 3.220 eV. The latter value is also the electron affinity (EA) of the phenylethynyl radical (PhCC•) from which a bond dissociation energy (BDE) of phenylacetylene (PhCCH) was derived to be ca. 131.3 ± 1.7 kcal mol-1 using a gas-phase thermochemical cycle. Detachment of an electron from PhCC– at 266 nm likely results in resonant autodetachment, supported by Franck-Condon Factor (FCF) simulations. The phenylacetylide anion reacts with methyl iodide (CH3I) and allyl iodide (C3H5I) via SN2 nucleophilic displacement with measured rate coefficients of 4.29 and 3.66 × 10-10 cm3 molecule-1 s-1, respectively. The mechanisms associated with these displacement reactions are explained and understood in terms of the reaction kinetics, natural bond orbital (NBO) theory, and Density Functional Theory (DFT) calculations.

Ma, Howard Z.↗

Uncovering the role of boronic acids and boroxines in the catalytic hydroboration of alkenes

The catalytic hydroboration of alkenes with pinacolborane (HBpin) represents a valuable yet challenging transformation in main-group catalysis, furnishing alkyl pinacol boronic esters of broad synthetic utility. In this article, we demonstrate that simple, commercially available aryl and alkyl boronic acids and their corresponding boroxines act as efficient pre-catalysts for the anti-Markovnikov hydroboration of terminal alkenes with HBpin under solvent-free conditions. In particular, 3,4,5-trifluorophenylboronic acid promotes hydroboration at low loadings, displays broad functional-group tolerance, and operates under operationally simple conditions. Detailed 11 B NMR spectroscopic studies reveal that boronic acids and boroxines are not the catalysts themselves, instead they react with HBpin to generate the transient species RBH 2 ·BH 2 R and B 2 H 6 , which serve as catalytically active intermediates. These species rapidly undergo alkene hydroboration followed by transborylation with HBpin to regenerate the catalytically competent hydridoboranes and release the alkyl pinacol boronic ester products. At elevated temperature and in the absence of alkene substrate, B 2 H 6 undergoes thermal fragmentation into the catalytically inactive borane clusters B 5 H 9 and B 10 H 14 . Limitations in the hydroboration of internal alkenes are traced to the formation of sterically congested trialkylboranes that do not undergo transborylation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An unwanted guest in the electrochemical oxidation of high-voltage Li-ion battery electrolytes: the life of highly reactive protons

Lithium-ion batteries (LIBs) are central to the urgent societal need to decarbonize both transportation and energy storage on the grid. Unfortunately, despite their attractive energy/power density, as well as high coulombic and energy efficiencies, further improvement of this technology – especially their durability – is desperately needed. To support these efforts, our study focuses on fundamental understanding of the decomposition pathways for LIB electrolytes at the cathode–electrolyte interface (CEI), as the nature of these reactions directly controls the extent to which cell capacity and voltage decays in these systems. In this study, we employ electrochemical methods, coupled with product analysis using NMR spectroscopy and mass spectrometry, to determine the decomposition mechanisms in both model and technologically relevant electrolytes. Remarkably, we discovered the electrochemical formation of protons with high chemical activity, comparable to known superacids, at potentials relevant to practical Li-ion batteries. Their reactivity toward every individual component of the CEI provides a unified thermochemical origin for a myriad of side reactions that are commonly associated with the electrochemical reaction. In particular, electrochemically generated protons react with intact EC molecules to form CO 2 and other short and long chain ethers. They also undergo an acid–base reaction with LiPF 6 , to form the weaker acid HF, and with the cathode active material, leaching transition metals into the electrolyte. Collectively, the results of this study all point to the urgent need to either mitigate this proton formation or introduce benign harvesting additives via new electrolyte design strategies.

Ilic, Stefan [Argonne National Laboratory (ANL), A↗

Unravelling chemical pathways of H 2 on Ga 2 O 3 surfaces with spectro-electrochemistry

This work highlights the capability of coupled spectroscopic and electrochemical techniques to probe dynamic surface processes under realistic operating conditions. By simultaneously employing in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and electrochemical impedance spectroscopy (EIS), we elucidate the mechanistic interaction between Ga 2 O 3 and hydrogen under elevated temperatures in a low-oxygen environment. This novel spectro-electrochemical approach allows chemistry to be correlated with the surface charge density of Ga 2 O 3 . Our results reveal a concentration-dependent transition in reaction pathway. At low concentrations, hydrogen reacts with ambient oxygen to form surface hydroxyls. At intermediate concentrations, hydrogen interacts with surface adsorbed oxygen to generate hydroxyl groups along with reducing the surface. Finally, at high H 2 concentrations, hydrogen reduces both hydroxyls and surface oxygen, leading to a highly conductive grain surface. As a result, hydrides form on the reduced Ga 2 O 3 surface. The gained insights are relevant for heterogeneous catalysis and gas sensing.

08 HYDROGEN↗

Proton transfer during reduction of the catalytic metallo-cofactors of the three nitrogenase isozymes

Nitrogenase catalyzes biological nitrogen fixation, the conversion of atmospheric N 2 into bioavailable ammonia. The three nitrogenase isozymes—Mo-nitrogenase, V-nitrogenase, and Fe-nitrogenase—utilize catalytic cofactors distinguished by their metal composition (Fe 7 M, M = Mo, V, or Fe; denoted FeM-co). Their catalytic cycles involve stepwise addition of 8[e−/H+] to FeM-co, generating intermediates designated E n , where n is the number of [e − /H + ] delivered. The electron-transfer has been extensively characterized, but the proton delivery has not. Here, we investigate [e − /H + ] delivery during early-stage conversions, primarily E 0 → E 1 (H), for each of the three nitrogenases, using as reductants γ-ray-generated thermolyzed, mobile electrons at 77 K, and radiation-generated solvent radicals during subsequent annealing to higher temperatures. Our results show E 0 → E 1 (H) conversion differs among the three MFe-proteins. The FeMo-co of MoFe-protein accepts an electron (ET) during 77 K γ-irradiation, but proton transfer (PT) to generate E 1 (H) is only enabled by conformational or thermodynamic activation upon cryoannealing to ∼200 K(ET/PT). For VFe-protein, E 1 (H) forms during annealing at-and-above 210 K by electron-transfer to FeV-co from radicals through proton-coupled electron transfer (PCET), which too is enabled by activated proton transfer. FeFe-protein differs in directly exhibiting delivery of protons at 77 K, which together with the mobile electrons react to form E 1 (H). This could well occur by PCET at 77 K, but does not preclude the possibility of sequential 77 K electron/proton transfer (ET/PT). In addition, 450 nm photolysis reveals the E 1 (H) state of FeV-co, like that of FeFe-co, contains a hydride bound to a formally oxidized cofactor. The mechanistic differences observed here provide a contribution towards understanding the sources of catalytic differences among the three nitrogenase isozymes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

First-principles thermodynamic assessment of Sr-containing secondary phase formation in strontium-substituted lanthanum manganites for solid oxide cell applications

Sr-secondary phase formation is a potentially significant degradation mode with direct impact upon solid-oxide cell (SOC) commercial viability. A first-principles based thermodynamic study was performed for La 1−x Sr x MnO 3±δ (LSM) perovskites to assess their stability against formation of different Sr-secondary phases, including SrO, SrCrO 4 , SrSO 4 , SrCO 3 , and Sr(OH) 2 , for SOC applications. The Sr-secondary phase formation reaction free energies were determined via a thermodynamic model by combining ab initio lattice dynamics calculations for the solid phases and ab initio thermodynamic data for the gas phases. The current approach expands the previously reported thermodynamic modeling studies by integrating first-principles based point defect equilibria into the thermodynamic analysis. The modeling results obtained using this new approach indicate an increased tendency to form the SrO oxide upon decreasing the oxygen partial pressure. Additionally, the enhancing factors to form the Sr-related secondary phase from the associated SrO activity in LSM are further quantified by considering the equilibrium of SrO reacting with the contaminant gas species as a function of temperature and pressure.

defect thermodynamics modeling↗

Vapor-phase pillarization of MXenes for engineering hierarchical interlayer porosity

MXenes, a family of two-dimensional (2D) multilamellar materials, possess excellent thermal and electronic properties for a range of applications. Their use in heterogeneous catalysis, however, is limited by the low surface area resulting from stacked layers. Pillarization with inorganic oxides can create more open, mesoporous MXene structures, improving accessibility for guest species to diffuse, reside or react in the space between 2D layers. A previous liquid-phase pillarization method, however, involves excessive use of solvent-based precursors and multiple processing steps. Here, we report a vapor-phase pillarization (VPP) strategy to introduce pillars, exemplified by silica pillars, with high pillar precursor usage efficiency and a simplified processing workflow. The resulting silica-pillared mesoporous MXene exhibits significantly increased surface area and porosity. These textural properties can be easily tuned by the VPP synthesis conditions. When applied as a ruthenium (Ru) catalyst support for the hydrogenolysis of low-density polyethylene (LDPE), the silica-pillared MXene enabled high Ru dispersion and catalytic activity. This study highlights the potential of the VPP method for engineering mesoporous, 2D MXene materials and demonstrates the effectiveness of mesoporous MXene as a catalyst support in overcoming mass transport and active-site accessibility challenges in heterogeneous catalysis involving bulky substances, such as plastics upcycling.

Luo, Song [University of Delaware, Newark, DE (Uni↗

Using Prompt Neutron Decay Constant Measurements to Obtain Additional Kinetics Information

Prompt neutron decay constant measurements are typically used to infer the prompt neutron lifetime in a chain-reacting system, but these measurements include much more information about the kinetics of the system. This work focuses specifically on the Rossi-α method of measuring the prompt neutron decay constant. The Rossi-α system of equations consists of five unknown parameters. With five unknowns and three equations, the system of equations solved by the Rossi-α measurement is under-determined. It has been postulated that a well posed problem can be formulated using independent measurement configurations on a single system. The external source strength, the effective delayed neutron fractions, and Diven’s parameter do not typically change for different configurations of a single experiment. If good detector geometry is chosen, the detector efficiency does not change for multiple measurements of a single experiment using Rossi-α measurements. By making these assumptions, there are only two unique variables. This knowledge can be used to solve for most of the unique parameters using two independent, unique Rossi-α measurements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Dry Deactivation of Sodium Metal in a Molten LiCl-KCl-CsCl-NaCl System

An experimental study was performed with the objective of investigating and characterizing a dry technique for deactivation of sodium metal in a molten salt system. The study was performed in three parts. First, proof-of-principle testing of the technique was performed at bench scale. It involved loading and melting tens of grams of clean sodium metal atop a pool of LiCl-KCl-CsCl eutectic at ∼300°C and then adding ammonium chloride particles while mixing. The ammonium chloride reacted with sodium to form sodium chloride and nitrogen/hydrogen off-gases. The sodium chloride assimilated into the salt pool, forming a quaternary salt mixture of LiCl-KCl-CsCl-NaCl. The proof-of-principle testing repeatedly exhibited complete deactivation of the loaded sodium metal. Second, characterization of a LiCl-KCl-CsCl-NaCl system was performed using differential scanning calorimetry to produce a partial phase diagram of LiCl-KCl-CsCl eutectic versus NaCl, which identified the liquidus, solidus, and two-phase regions of the quaternary system. Third, the dry deactivation technique was demonstrated at kg-scale in an inert atmosphere radiological glovebox with sodium metal that was previously separated in the same glovebox from uranium metal in unirradiated blanket elements for the Fermi-1 nuclear reactor. The quaternary salt product at the end of the demonstration was sampled and showed complete deactivation of the sodium metal. Here, in short, this study qualified a technique to completely deactivate batches of sodium metal in the absence of air or water. While this study focused on the deactivation of sodium metal, including bond sodium from unirradiated blanket elements, the technique is applicable to other sources of sodium metal, such as sodium metal from batteries. Furthermore, the technique could also be extended to other alkali metal systems, including lithium, sodium, potassium, rubidium, cesium, and mixtures thereof.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reversible oxidation and reduction of gold-supported iron oxide islands at room temperature

Monolayer iron oxides grown on metal substrates have widely been used as model systems in heterogeneous catalysis. By means of ambient-pressure scanning tunneling microscopy (AP-STM), we studied the in situ oxidation and reduction of FeO(111) grown on Au(111) by oxygen (O 2 ) and carbon monoxide (CO), respectively. Oxygen dislocation lines present on FeO islands are highly active for O 2 dissociation. X-ray photoelectron spectroscopy measurements distinctly reveal the reversible oxidation and reduction of FeO islands after sequential exposure to O 2 and CO. Here, our AP-STM results show that excess O atoms can be further incorporated on dislocation lines and react with CO, whereas the CO is not strong enough to reduce the FeO supported on Au(111) that is essential to retain the activity of oxygen dislocation lines.

36 MATERIALS SCIENCE↗

Ambient pressure x-ray photoelectron spectroscopy study of water formation and adsorption under two-dimensional silica and aluminosilicate layers on Pd(111)

Ambient pressure x-ray photoelectron spectroscopy (AP-XPS) supported by density functional theory (DFT) calculations was used to characterize the interaction of water with two-dimensional (2D) silica and aluminosilicate bilayers on Pd(111). Starting with oxygen adsorbed at the SiO2/Pd interface, exposure to water caused the SiO 2 -derived XPS peaks to shift to higher binding energy and the removal of an O 1s feature associated with interfacial adsorbed oxygen. These observations were attributed to the formation of a mixed water–hydroxyl interface, which eliminates the interfacial dipolar layer, and its associated electrostatic potential, created by adsorbed oxygen. Interfacial oxygen also reacted with H 2 to produce adsorbed water which also caused an upward binding energy shift of the SiO 2 peaks. Spectra recorded under 0.5 Torr water revealed additional water adsorption and a further shift of the overlayer peaks to higher binding energy. Incorporating Al into the 2D material caused the bilayer peaks to shift to lower binding energy which could be explained by electron donation from the metal to the bilayer. Although the stronger interaction between the bilayer and Pd substrate should restrict interfacial adsorption and reaction, similar trends were observed for water and hydrogen exposure to interfacial adsorbed oxygen. Less water adsorption was observed at the aluminosilicate interface which is a consequence of Al strengthening the bond to the metal substrate. The results reveal how the sensitivity of XPS to interfacial dipoles can be exploited to distinguish reactions taking place in confined spaces under 2D layers and how tuning the composition of the 2D layer can impact such reactions.

Density functional theory↗

Forward modeling of Doppler velocity interferometer system for improved shockwave measurements

We report that when near-instantaneous shocks are recorded by using a Doppler velocity interferometer velocity interferometer system for any reflector (VISAR), they typically exceed the detector’s ability to react and “skipped fringes” result, where its visibility briefly reduces. Traditionally, replacing skipped fringes required guesswork in analysis, which increased arrival time errors. Second, the use of long but velocity-sensitive interferometer delays with fast detectors which can resolve the delay has traditionally been avoided because of the fear of confusing the arrival time signal. However, shorter delays produce smaller fringe phase shifts per velocity and, thus, can decrease velocity precision. We realize that while some loss of fringe information occurs at shock events, this is often just a partial loss and the residual fringe information can still hold valuable information. We describe a forward model (FM) of the interferometer action and detector blurring that assists with VISAR fringe analysis at skipping events: (1) more precise shock arrival times, (2) arrival time precision not limited by long delays, and (3) improved ghost subtraction, which improves accuracy over a broad time region. Lastly, we demonstrate the utility of a FM on National Ignition Facility and Laboratory for Laser Energetics Omega shots and discuss data process methods to increase the high time resolution of VISAR systems despite their limitations and complexities.

47 OTHER INSTRUMENTATION↗

VIPIR: A High-Throughput Drop-Weight Impact Instrument for Imaging the Initiation and Propagation of Reactions in Energetic Materials

Characterizing the handling safety and sensitivity of explosives has been a challenging area of study for over 60 years. Historically one of the most accessible and widely utilized experiments has been the drop-weight impact test, which involves dropping a weight on a small sample sandwiched between two anvils. Because this experiment generally only utilizes sound thresholds to determine whether or not a sample reacted, the physical and chemical properties governing sensitivity remain convolved. Better understanding of chemical and material characteristics is needed to give the chemistry and engineering communities a predictive tool to determine the handling sensitivity of explosives prior to pursuing expensive and potentially hazardous synthesis and formulation operations. Here, we are developing a high throughput drop tower instrument capable of imaging the deformation and flow of energetic materials during impact and the resulting thermal ignition and propagation events. This instrument is based on previous designs but has been modified for higher throughput and tailorable modifications in the future. Herein, we present key design features that enable high-speed visible and thermal imaging of explosive initiation by sub-shock impacts, as well as preliminary results in which ignition sites were observed in an erythritol tetranitrate sample.

47 OTHER INSTRUMENTATION↗

Atomistic mechanisms for catalytic transformations of NO to NH3, N2O, and N2 by Pd

The industrial pollutant NO is a potential threat to the environment and to human health. Thus, selective catalytic reduction of NO into harmless N2, NH3, and/or N2O gas is of great interest. Among many catalysts, metal Pd has been demonstrated to be most efficient for selectivity of reducing NO to N2. However, the reduction mechanism of NO on Pd, especially the route of N−N bond formation, remains unclear, impeding the development of new, improved catalysts. We report here the elementary reaction steps in the reaction pathway of reducing NO to NH3, N2O, and N2, based on density functional theory (DFT)-based quantum mechanics calculations. We show that the formation of N2O proceeds through an Eley-Rideal (E−R) reaction pathway that couples one adsorbed NO* with one non−adsorbed NO from the solvent or gas phase. This reaction requires high NO* surface coverage, leading first to the formation of the trans-(NO)2* intermediate with a low N−N coupling barrier (0.58 eV). Notably, trans-(NO)2* will continue to react with NO in the solvent to form N2O, that has not been reported. With the consumption of NO and the formation of N2O* in the solvent, the Langmuir-Hinshelwood (L-H) mechanism will dominate at this time, and N2O* will be reduced by hydrogenation at a low chemical barrier (0.42 eV) to form N2. In contrast, NH3 is completely formed by the L-H reaction, which has a higher chemical barrier (0.87 eV). Our predicted E-R reaction has not previously been reported, but it explains some existing experimental observations. In addition, we examine how catalyst activity might be improved by doping a single metal atom (M) at the NO* adsorption site to form M/Pd and show its influence on the barrier for forming the N−N bond to provide control over the product distribution.

Physics↗

Identifying crystal structures and chemical reactions at the interface of stanene on Bi 2 Te 3

Synthesizing monolayers and heterostructures is an enabling approach to extract new physical phenomena from bulk materials. Among the structures amenable to this approach is stanene, which is a monolayer of tin, similar to graphene, and has been predicted to host one-dimensional topological states at its edges. Stanene can be tuned by decorating with different adatoms, which makes it a promising platform on which to engineer topological devices. Here, we deposit Sn on Bi 2 Te 3 and characterize the growth using anomalous synchrotron x-ray scattering and x-ray photoelectron spectroscopy (XPS). X-ray diffraction data reveal the formation of epitaxial Sn-based structures, along with penetration of Sn into the Bi 2 Te 3 , with Sn intercalating between the upper 10 Bi 2 Te 3 quintuple layers. Additionally, XPS data show deposited Sn reacting to form SnTe and Bi at the Bi 2 Te 3 surface. The calculated heat of reaction for Sn and Bi2Te3 is consistent with an exothermic reaction to SnTe and Bi. Using thermodynamic calculations as a guide, we identify several candidate substrates that can stabilize the stanene phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Importance learning estimator for the site-averaged turnover frequency of a disordered solid catalyst

For disordered catalysts such as atomically dispersed “single-atom” metals on amorphous silica, the active sites inherit different properties from their quenched-disordered local environments. The observed kinetics are site-averages, typically dominated by a small fraction of highly active sites. Standard sampling methods require expensive ab initio calculations at an intractable number of sites to converge on the siteaveraged kinetics. We present a new method that efficiently estimates the site-averaged turnover frequency (TOF). The new estimator uses the same importance learning algorithm [Vandervelden et al., React. Chem. Eng. 5, 77 (2020)] that we previously used to compute the siteaveraged activation energy. We demonstrate the method by computing the site-averaged TOF for a simple disordered lattice model of an amorphous catalyst. The results show that with the importance learning algorithm, the site-averaged TOF and activation energy can now be obtained concurrently with orders of magnitude reduction in required ab initio calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗