Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROUGHNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Laser-Hardened and Ultrasonically Peened Surface Layers on Tool Steel AISI D2: Correlation of the Bearing Curves’ Parameters, Hardness and Wear

This paper is focused on the effects of the separately applied laser heat treatment (LHT) and ultrasonic impact treatment (UIT) and the combined LHT + UIT process on the wear and friction behaviors of the hardened surface layers of the tool steel AISI D2. In comparison with the initial state, wear losses of the treated specimens after long-term wear tests were decreased by 68, 41, and 77% at the LHT, UIT, and combined LHT + UIT processes, respectively. The Abbott–Firestone bearing curves were used to analyze the material ratio and functional characterization (bearing capacity and oil capacitance) of the studied surface specimens. The wear losses registered after short (15 min) tests correlate well with the changes in experimental surface roughness Ra, and the predictive Rpk, and bearing capacity B{sub C} parameters, respectively, evaluated using the Abbott–Firestone curves and Kragelsky–Kombalov formula. The wear losses after the long-term (45 min) tests are in good correlation with the reciprocal surface microhardness HV and with the W{sub L} and W{sub P} wear parameters, respectively, estimated using Archard–Rabinowicz formula and complex roughness-and-strength approach. The observed HV increase is supported by nanotwins (LHT), by dense dislocation nets (UIT), and by dislocation cells/nanograins fixed with fine carbides (LHT + UIT) formed in the surface layers of the steel.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Al{sub 2}O{sub 3}-TiC Composite Prepared by Spark Plasma Sintering Process: Evaluation of Mechanical and Tribological Properties

Al{sub 2}O{sub 3}-10TiC composites were synthesized by spark plasma sintering (SPS) process. Microstructural and mechanical properties of the composite reveal homogeneous distribution of the fine TiC particles in the matrix. The samples were produced with different sintering temperature, and it shows that the hardness and density gradually increases with increasing sintering temperature. Abrasion wear test result reveals that the composite sintered at 1500 °C shows high abrasion resistance (wt. loss ~ 0.016 g) and the lowest abrasion resistance was observed for the composite sample sintered at 1100 °C (wt. loss ~ 1.459 g). The profilometry surface roughness study shows that sample sintered at 1100 °C shows maximum roughness (R{sub a} = 6.53 µm) compared to the sample sintered at 1500 °C (R{sub a} = 0.66 µm) corroborating the abrasion wear test results.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Electropulsing-Assisted Ultrasonic Nanocrystalline Surface Modification on the Surface Mechanical Properties and Microstructure of Ti-6Al-4V Alloy

The effect of electropulsing-assisted ultrasonic nanocrystalline surface modification (EP-UNSM) on surface mechanical properties and microstructure of Ti-6Al-4V alloy is investigated. Compared to conventional ultrasonic nanocrystalline surface modification (UNSM), EP-UNSM can effectively facilitate surface roughness and morphology, leading to excellent surface roughness (reduced from Ra 0.918 to Ra 0.028 μm by UNSM and Ra 0.019 μm by EP-UNSM) and smoother morphology with less cracks and defects. Surface friction coefficients are enhanced, resulting in lower and smoother friction coefficients. In addition, the surface-strengthened layer and ultra-refined grains are significantly enhanced with more severe plastic deformation and a greater surface hardness (a maximum hardness value of 407 HV and an effective depth of 550 μm, in comparison with the maximum hardness value of 364 HV and effective depth of 300 μm obtained by conventional UNSM). Remarkable enhancement of surface mechanical properties can be attributed to the refined gradient microstructure and the enhanced severe plastic deformation layer induced by coupling the effects of UNSM and electropulsing. The accelerated dislocation mobility and atom diffusion caused by the thermal and athermal effects of electropulsing treatment may be the primary intrinsic reasons for these improvements.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A Study on the Corrosion Behavior of Carbon Steel Exposed to a H{sub 2}S-Containing NH{sub 4}Cl Medium

NH{sub 4}Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H{sub 2}S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H{sub 2}S concentration, on the corrosion behavior of carbon steel in an NH{sub 4}Cl environment with the presence of H{sub 2}S. The effect of H{sub 2}S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H{sub 2}S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H{sub 2}S environment, and the corrosion product film was tight and protective. The ammonia from NH{sub 4}Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness (R{sub a}) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH{sub 4}Cl environment with the presence of H{sub 2}S.

36 MATERIALS SCIENCE↗
DOE OSTI2018

3D Gel-Printing of TiC-Reinforced 316L Stainless Steel: Influence of the Printing Parameters

In this paper, the composite composed of TiC (35 wt.%) reinforced 316L stainless steel matrix was successfully prepared using a 3D gel-printing (3DGP) process. The “step effect” of 3D printing can be reduced using reasonable parameter settings. The properties of TiC/316L slurry for 3DGP and the influence of the different printing parameters on the surface quality of the samples, such as the extrusion overlaps and printing speed, were researched. The microstructure and fracture morphology of the sintered sample were revealed using scanning electron microscopy. The surface roughness, density, and mechanical properties were also measured. When the internal diameter of the nozzle was 0.50 mm, the result showed that the proper extrusion overlap parameter was 0.08 mm and the maximum printing speed was 20 mm/s. Furthermore, the minimum surface roughness value was 10 μm. After sintering, the mechanical performances were similar to those obtained using a conventional powder metallurgy process.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Surface Treatment of Powder-Bed Fusion Additive Manufactured Metals for Improved Fatigue Life

High-cycle fatigue (HCF) tests were conducted on samples fabricated by two powder-bed additive manufacturing techniques. Samples were tested with as-produced surfaces and after various non-contact surface improvement treatments. Ti-6Al-4V samples were made using both electron beam melting (EBM) and selective laser melting (SLM), while Inconel 625 was fabricated using SLM. Ti-6Al-4V was treated with a commercial chemically accelerated vibratory polishing process, with target material removal of approximately 200 µm from each surface for EBM samples and 100 µm for SLM samples. This technique led to increases in both the number of cycles before failure at a given loading condition and endurance limit (at 10{sup 7} cycles) compared to samples with as-produced surfaces. The results are interpreted as the reduction in elastic stress concentration factor associated with surface defects where fatigue cracks initiate. SLM 625 was treated with both an abrasive polishing method and laser surface remelting. Both methods led to improvements in surface roughness, but these did not lead to improvements in fatigue properties of SLM 625. For abrasive polished samples, the combination of improved measured surface roughness without fatigue property enhancement suggests that surface material is removed, but the roots of surface defects, where fatigue cracks initiate, were left intact. For laser treatment, the remelted surface layer retained a rapidly solidified microstructure that did not increase the number of cycles before crack initiation even though the surface was smoother compared to the surface prior to polishing.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Experimental Investigations for Optimizing the Extrusion Parameters on FDM PLA Printed Parts

Fused deposition modeling (FDM) has become one of the most extensively used additive manufacturing technologies in recent years because of its wide adaptability, simple mechanism and low cost. It is difficult, however, to achieve an equitable trade-off among mechanical properties, surface finish quality and production time, which is an area seldom explored. This paper concentrates on the optimization of the parameters to achieve higher tensile strength and lower surface roughness with less build time during the FDM process based on central composite design for the tensile specimen forming process. The effects of five extrusion parameters (nozzle diameter, liquefier temperature, extrusion velocity, filling velocity and layer thickness) on the three outputs of tensile strength (TS), surface roughness (SR) and build time (BT) are investigated. Response surface methodology combined with nondominated sorting genetic algorithm II is developed to optimize the process parameters to achieve the maximum TS, minimum SR and BT, as verified by subsequent experiments. The predicted results are found to be very close to the experimental data, illustrating that the presented approach in this paper is effective for improving mechanical properties, surface finish and efficiency of the FDM process.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Mechanical Surface Treatments of AISI 304 Stainless Steel: Effects on Surface Microrelief, Residual Stress, and Microstructure

The surface roughness, residual stress, and microstructure of AISI 304 stainless steel specimens after laser shock peening (LSP), water jet cavitation peening (WjCP), water jet shot peening (WjSP), and multi-pin ultrasonic impact treatment (UIT) were studied in this work. Compared to the initial state, the surface roughness (Ra) was, respectively, decreased by approx. 5.5, 7.8, 38.2, and 91.1% after the LSP, WjCP, WjSP, and UIT processes. The volume fraction of ε-martensite of ~ 3-5% was observed in all treated specimens except for the LSP-treated ones. The volume fraction of α′-martensite was increased in the following sequence: WjCP (~ 5%), LSP (~ 5%), WjSP (~ 25%), UIT (~ 50%). The studied mechanical surface treatments promote a significant reduction in grains size of both austenite (~ 15-20 nm) and martensite (~ 20-37 nm) leading to essential hardening. All studied processes result in the formation of compressive residual stresses (− 377…693 MPa) and the improvement in the bearing curve parameters. The microhardness estimated accounting for the contributions of different hardening mechanisms to the yield strength magnitude correlates well with the experimental data. The grain boundary hardening and dislocation hardening are concluded to be the most influential mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Electrodeposition and Characterization of Cr-MoS{sub 2} Composite Coatings

In this study, Cr-MoS{sub 2} composite coatings were electrodeposited from conventional Cr{sup +6} baths containing different amounts of MoS{sub 2} particles and various types of surfactant (cationic and anionic). The effect of bath chemical composition on the coatings properties like their microstructure, morphology, chemical composition, corrosion behavior, surface roughness and microhardness was investigated using x-ray diffraction, scanning electron microscopy (SEM), energy-dispersive x-ray analysis, potentiodynamic polarization, electrochemical impedance spectroscopy, surface profilometry and Vickers microhardness measurement techniques, respectively. The results showed that incorporation of MoS{sub 2} particles into the composite coatings is very limited and Cr matrix with very low crystallinity will be electrodeposited at various experimental conditions. The presence of MoS{sub 2} particles in the bath (up to an optimum value) leads to the formation of the composite coatings with lower surface roughness values than that of conventional chromium coating. Although more MoS{sub 2} particles will be incorporated into the electrodeposits when the solid content of the bath increases, chromium cannot be electrodeposited from baths containing high amounts of MoS{sub 2} particles. Application of cationic surfactant promotes incorporation of particles into the Cr metallic matrix. Moreover, the presence of surfactant in the bath results in the formation of coatings with less microcracks. All the composite coatings have more hardness values than that of conventional chromium coating; maximum hardness is attributed to the coatings that were electrodeposited from baths containing no surfactant. The corrosion test results revealed that the smooth coatings containing more MoS{sub 2} particles and less microcracks exhibit more corrosion resistance than the other ones.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Ultrasonic Surface Rolling Parameters on Surface Integrity of TC17 Alloy

The main purpose of this paper was to investigate the effects of different static forces and feed speeds of ultrasonic surface rolling (USR) on the surface integrity of TC17 alloy. Surface roughness, in-depth residual stress, in-depth microhardness, and cross-sectional microstructure of the processed materials were measured and analyzed to get a comprehensive knowledge of the surface characteristics under different conditions. The results indicate that the specimens treated by USR achieve a considerable improvement in surface roughness (R{sub a} 0.04-0.10 μm); meanwhile, the surface morphology is smooth and uniform. Moreover, the surface residual stress and microhardness are greatly improved compared to those of untreated specimen. The maximum compressive residual stress is approximately − 966 MPa at the depth of 300 μm, and the thickness of strengthened layer is about 1000 μm. The material of affected layer experiences plastic deformation in a certain extent. Moreover, the gradient change in microstructure and white layer are also observed on the subsurface layer. It is also concluded from the study that static force has a more significant impact on surface integrity characteristics compared with feed speed.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Flow and Turbulence Control in a Boundary Layer Wind Tunnel Using Passive Hardware Devices

The Climatic Wind Tunnel (CWT) is a new experimental facility of the Institute of Theoretical and Applied Mechanics (ITAM) in Prague, Czech Republic. It is uniquely able to replicate precipitation and freezing effects on structural models in the climatic test section, and simultaneously perform aerodynamic and aeroelastic tests on structural models in the aerodynamic test section. Extensive measurements are carried out to investigate airflow and turbulence characteristics in the empty aerodynamic test section. Capability to experimentally simulate the atmospheric boundary layer (ABL) is studied using castellated barrier wall, Counihan vortex generators, and surface roughness elements. An individual influence of each of these passive hardware devices is separately tested as well, as they are commonly used combined, and their individual contributions to the ABL model characteristics are not well known. The analysis is based on hot-wire anemometer measurements carried out at various cross sections in the aerodynamic test section of the CWT. Experimental results are reported as mean velocity and turbulence intensity fields for the empty aerodynamic test section without passive hardware devices. Vertical profiles of mean velocity, turbulence intensity, and turbulence length scales, as well as power spectral density of velocity fluctuations, are reported for the ABL small-scale model. The barrier is observed to cause a decrease in flow velocity and an increase in turbulence close to surface. Vortex generators enhance turbulence throughout the entire height range under scope. Increased turbulence and decreased flow velocity are particularly exhibited close to surface due to surface roughness. Influence of each of the studied passive hardware devices on flow and turbulence is quantified in a dimensionless form to allow for separately accounting for their effects.

42 ENGINEERING↗
DOE OSTI2020

Quantitatively accounting for the effects of surface topography on the oxidation kinetics of additive manufactured Hastelloy X processed by electron beam melting

In this work, the effects of surface roughness on the high-temperature corrosion of nickel-based superalloy X produced through electron-beam melting (EBM) additive manufacturing were studied. Surface area of samples in the rough, as-fabricated condition was measured using a 2D cross-section image analysis technique and a 3D image analysis technique. To verify the accuracy of surface area measurements, oxidation testing of samples in the as-fabricated and polished conditions was performed; polished sample oxidation curves were then compared to the as-fabricated sample oxidation curves before and after being adjusted using obtained surface area measurements. It was found that the 2D technique accurately measured surface area and accounted for the overlapping features present on EBM sample surfaces, whereas the 3D technique did not. Further, it was also observed that oxidation kinetics were moderately faster on the alloy X samples in the as-fabricated condition than for the polished condition.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Rapid imbibition of water in fractures within unsaturated sedimentary rock

The spontaneous imbibition of water and other liquids into gas-filled fractures in variably-saturated porous media is important in a variety of engineering and geological contexts. However, surprisingly few studies have investigated this phenomenon. In this paper, we present a theoretical framework for predicting the 1-dimensional movement of water into air-filled fractures within a porous medium based on early-time capillary dynamics and spreading over the rough surfaces of fracture faces. The theory permits estimation of sorptivity values for the matrix and fracture zone, as well as a dispersion parameter which quantifies the extent of spreading of the wetting front. Quantitative data on spontaneous imbibition of water in unsaturated Berea sandstone cores were acquired to evaluate the proposed model. The cores with different permeability classes ranging from 50 to 500 mD and were fractured using the Brazilian method. Spontaneous imbibition in the fractured cores was measured by dynamic neutron radiography at the Neutron Imaging Prototype Facility (beam line CG-1D, HFIR), Oak Ridge National Laboratory. Water uptake into both the matrix and the fracture zone exhibited square-root-of-time behavior. The matrix sorptivities ranged from 2.9 to 4.6 mm s -0.5 , and increased linearly as the permeability class increased. The sorptivities of the fracture zones ranged from 17.9 to 27.1 mm s -0.5 , and increased linearly with increasing fracture aperture width. The dispersion coefficients ranged from 23.7 to 66.7 mm 2 s -1 and increased linearly with increasing fracture aperture width and damage zone width. Both theory and observations indicate that fractures can significantly increase spontaneous imbibition in unsaturated sedimentary rock by capillary action and surface spreading on rough fracture faces. Fractures also increase the dispersion of the wetting front. In conclusion, further research is needed to investigate this phenomenon in other natural and engineered porous media.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2013

Surface treated polypropylene (PP) fibres for reinforced concrete

Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Investigating relationship between surface topography and emissivity of metallic additively manufactured parts

Due to the direct relationship between thermal history and mechanical behavior, in situ thermal monitoring is key in gauging quality of parts produced with additive manufacturing (AM). Accurate monitoring of temperatures in an AM process requires knowledge of environment and object parameters including object emissivity. The emissivity is dependent on several variables, including: wavelength, material composition, temperature, and surface topography. Researchers have been concerned with the thermal emissivity dependence on temperature since large ranges are seen in metal powder bed processes, but there is also an extensive range of surfaces produced by AM. This work focused on discovering what roughness characteristics control thermal emissivity through investigation of prototypic 316 stainless steel AM samples produced with a range of build conditions on a laser powder bed fusion machine. Through experimental measurements of emissivity using hemispherical directional reflectance (HDR), guided by simulations using a finite-difference time-domain (FDTD) Maxwell solver, it was found that combinations of existing roughness parameters describing both height and slope of the surface correlate well with emissivity changes. Furthermore, these parameters work well due to their apt description of surface features encouraging internal reflection, which is the phenomenon that increases emissivity when a surface falls under the geometric optical region conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A review on the fatigue behavior of Ti-6Al-4V fabricated by electron beam melting additive manufacturing

Electron beam melting (EBM) is a swiftyly-developing metal additive manufacturing process that holds significant interest in the aerospace and biomedical industries for the high-strength titanium alloy, Ti-6Al-4V. These industries have fatigue-limited applications, yet a lack of understanding of the EBM process-microstructure-fatigue relationships limit widespread use and presents challenges for certification. In this review, uniaxial fatigue data was collected and the effects of build orientation, surface roughness, and hot-isostatic pressing are linked to the fatigue properties highlighting microstructure, defects, and failure mechanisms. The observations and conclusions are supported by statistical analysis using the mean fatigue life obtained by the Statistical Fatigue-Limit Model. Both EBM-process and post-process structure relationships are discussed in order to identify the best-practice for fatigue-resistant design. The performance of the EBM material is compared to conventionally manufactured Ti-6Al-4V and possible methods to increase the fatigue resistance are discussed. Anisotropic fatigue behavior was observed in as-fabricated parts and no statistical distinction was found in the fatigue performance of HIPed and as-fabricated material provided the same as-fabricated rough surface condition. However, comparable fatigue life to traditionally manufactured lamellar Ti-6Al-4V is achieved when both post-process HIP and machining are applied to EBM-fabricated parts.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of nitriding on mechanical and microstructural properties of Direct Metal Laser Sintered 17-4PH stainless steel

In this work, the effect of the nitriding process on microstructure and mechanical properties of additively manufactured (AM) 17-4PH stainless steel is investigated. The nitriding was performed at 530 °C, 560 °C, and 580 °C for 2 h. The nitriding process improves the hardness and surface roughness of the AM 17-4PH steel. Detailed microstructural characterizations of both as-built and nitride samples are performed using an optical microscope, scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction technique. It reveals that the nitride layer thickness increases with nitriding temperature. A distinct transition layer between the substrate and nitride layer is observed in the 560 °C and 580 °C nitride samples. The nitriding process develops almost equiaxed grain microstructure with new secondary phase precipitates, whereas in the as-built material, the grains are primarily columnar along the AM process build direction. Specifically, the nitriding process introduces γ-Fe4N, ε-Fe3N, CrN, and Ni3N precipitates. The increase in Ni- and Cu-rich precipitates with the nitriding temperature explains the observed improvement in the hardness and surface roughness. Furthermore, the nitriding process does not alter the substrate's initial weak crystallographic texture.

17-4PH steel↗
DOE OSTI2014

The effect of spatial micro-CT image resolution and surface complexity on the morphological 3D analysis of open porous structures

In material science microfocus X-ray computed tomography (micro-CT) is one of the most popular non-destructive techniques to visualise and quantify the internal structure of materials in 3D. Despite constant system improvements, state-of-the-art micro-CT images can still hold several artefacts typical for X-ray CT imaging that hinder further image-based processing, structural and quantitative analysis. For example spatial resolution is crucial for an appropriate characterisation as the voxel size essentially influences the partial volume effect. However, defining the adequate image resolution is not a trivial aspect and understanding the correlation between scan parameters like voxel size and the structural properties is crucial for comprehensive material characterisation using micro-CT. Therefore, the objective of this study was to evaluate the influence of the spatial image resolution on the micro-CT based morphological analysis of three-dimensional (3D) open porous structures with a high surface complexity. In particular the correlation between the local surface properties and the accuracy of the micro-CT-based macro-morphology of 3D open porous Ti6Al4V structures produced by selective laser melting (SLM) was targeted and revealed for rough surfaces a strong dependence of the resulting structure characteristics on the scan resolution. Reducing the surface complexity by chemical etching decreased the sensitivity of the overall morphological analysis to the spatial image resolution and increased the detection limit. This study showed that scan settings and image processing parameters need to be customized to the material properties, morphological parameters under investigation and the desired final characteristics (in relation to the intended functional use). Customization of the scan resolution can increase the reliability of the micro-CT based analysis and at the same time reduce its operating costs. - Highlights: • We examine influence of the image resolution on μCT-based morphological analysis. • Surface properties influence accuracy of μCT-based morphology of porous structures. • Total porosity was the least sensitive to surface complexity and scan voxel size. • The beam thickness analysis was overestimated by the surface roughness. • Voxel size customization can significantly reduce a cost of the μCT-based analysis.

36 MATERIALS SCIENCE↗