Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Response of complex networks to compression: Ca, La, and Y aluminoborosilicate glasses formed from liquids at 1 to 3 GPa pressures

Aluminoborosilicate glasses containing relatively high field strength modifiers (Ca, La, and Y) have been compressed at pressures up to 3 GPa and near the glass transition temperature (T{sub g}) and quenched to room temperature at high pressure followed by decompression. Structural changes were quantified with high-resolution {sup 27}Al and {sup 11}B MAS nuclear magnetic resonance at 14.1–18.8 T. The changes with pressure in Al and B coordinations in the recovered samples are quite large with more than 50% decreases in tetrahedral aluminum ({sup IV}Al) and 200%-300% increases in tetrahedral boron ({sup IV}B). Glasses with higher field strength modifiers (La and Y) contain more high coordinated aluminum ({sup V,V} {sup I}Al) at all pressures studied. More high coordinated boron also correlates with higher field strength modifier if all three compositions are compared on an isothermal basis. Although lowering fictive temperature and increasing pressure both increase Al and B coordinations, our study shows that the actual mechanisms for structural changes are most probably different for temperature and pressure effects. Using a rough thermodynamic model to extrapolate to higher pressures, it appears that a simple non-bridging oxygen (NBO) consumption mechanism is not sufficient to convert all the aluminum to octahedral and boron to tetrahedral coordination, suggesting other mechanisms for structural changes could occur at high pressure as NBO becomes depleted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Prediction of B1 to B10 phase transition in LuN under pressure: An ab-initio investigation

Ab-initio total energy calculations have been performed in lutetium nitride (LuN) as a function of hydrostatic compression to understand the high pressure behavior of this compound. Our calculations predict a phase transition from ambient rocksalt type structure (B1 phase) to a tetragonal structure (B10 phase) at ~ 240 GPa. The phase transition has been identified as first order in nature with volume discontinuity of ~ 6%. The predicted high pressure phase has been found to be stable up to at least 400 GPa, the maximum pressure up to which calculations have been performed.Further, to substantiate the results of static lattice calculations analysis of lattice dynamic stability of B1 and B10 phase has been carried out at different pressures. Apart from this, we have analyzed the lattice dynamic stability CsCl type (B2) phase around the 240 GPa, the pressure reported for B1 to B2 transition in previous all-electron calculations by Gupta et al. 2013. We find that the B2 structure is lattice dynamically unstable at this pressure and remains unstable up to ~ 400 GPa, ruling out the possibility of B1 to B2 phase transition at least up to ~ 400 GPa. Further, the theoretically determined equation of state has been utilized to derive various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus of B1 phase at ambient conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High pressure behaviour of uranium dicarbide (UC{sub 2}): Ab-initio study

The structural stability of uranium dicarbide has been examined under hydrostatic compression employing evolutionary structure search algorithm implemented in the universal structure predictor: evolutionary Xtallography (USPEX) code in conjunction with ab-initio electronic band structure calculation method. The ab-initio total energy calculations involved for this purpose have been carried out within both generalized gradient approximations (GGA) and GGA + U approximations. Our calculations under GGA approximation predict the high pressure structural sequence of tetragonal → monoclinic → orthorhombic for this material with transition pressures of ∼8 GPa and 42 GPa, respectively. The same transition sequence is predicted by calculations within GGA + U also with transition pressures placed at ∼24 GPa and ∼50 GPa, respectively. Further, on the basis of comparison of zero pressure equilibrium volume and equation of state with available experimental data, we find that GGA + U approximation with U = 2.5 eV describes this material better than the simple GGA approximation. The theoretically predicted high pressure structural phase transitions are in disagreement with the only high experimental study by Dancausse et al. [J. Alloys. Compd. 191, 309 (1993)] on this compound which reports a tetragonal to hexagonal phase transition at a pressure of ∼17.6 GPa. Interestingly, during lowest enthalpy structure search using USPEX, we do not see any hexagonal phase to be closer to the predicted monoclinic phase even within 0.2 eV/f. unit. More experiments with varying carbon contents in UC{sub 2} sample are required to resolve this discrepancy. The existence of these high pressure phases predicted by static lattice calculations has been further substantiated by analyzing the elastic and lattice dynamic stability of these structures in the pressure regimes of their structural stability. Additionally, various thermo-physical quantities such as equilibrium volume, bulk modulus, Debye temperature, thermal expansion coefficient, Gruneisen parameter, and heat capacity at ambient conditions have been determined from these calculations and compared with the available experimental data.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-pressure response of vibrational properties of b-As x P 1– x : in situ Raman studies

The structural evolution of black arsenic-phosphorous (b-As x P 1–x ) alloys with varying arsenic concentrations was investigated under hydrostatic pressure using in situ Raman spectroscopy. High-pressure experiments were conducted using a diamond anvil cell, which revealed pressure-induced shifts in vibrational modes associated with P–P bonds (A 1 g , A 2 g , ${B}_{2g}$), As–As bonds (A 1 g , A 2 g , ${{B}}_{2g}$), and As–P bonds in b-As x P 1–x alloys. Two distinct pressure regimes were observed. In the first regime (region I), all vibrational modes exhibited a monotonic upshift, indicating phonon hardening due to hydrostatic pressure. In the second regime (region II), As 0.4 P 0.6 and As 0.6 P 0.4 alloys displayed a linear blueshift (or negligible change in some modes) at a reduced rate, suggesting local structural reorganization with less compression on the bonds. Notably, the alloy with the highest As concentration, As 0.8 P 0.2 , exhibited anomalous behavior in the second pressure regime, with a downward shift observed in all As–As and As–P Raman modes (and some P–P modes). Interestingly, the emergence of new peaks corresponding to the E g mode and A 1g mode of the gray-As phase was observed in this pressure range, indicating compressive strain-induced structural changes. The anomalous change in region II confirms the formation of a new local structure, characterized by elongation of the P–P, As–As, and As–P bonds along the zigzag direction within the b-As x P 1–x phase, possibly near the grain boundary. Additionally, a gray-As phase undergoes compressive structural changes. This study underscores the significance of pressure in inducing structural transformations and exploring novel phases in two-dimensional materials, including b-As x P 1–x alloys.

36 MATERIALS SCIENCE↗

Phase transitions and photoinduced transformations at high pressure in the molecular donor-acceptor fullerene complex (Cd(dedtc){sub 2}){sub 2} · C{sub 60}

The Raman spectra of crystals of C{sub 60} fullerene-cadmium diethyldithiocarbamate molecular donor-acceptor complexes (Cd(dedtc){sub 2}){sub 2} · C{sub 60} were measured at pressures of up to 17 GPa, and the crystal lattice parameters of these complexes were determined at pressures of up to 6 GPa. An increase in pressure up to ∼2 GPa leads to changes in the Raman spectra, which are manifested by splitting of the intramolecular H{sub g}(1)-H{sub g}(8) phonon modes and by softening of the A{sub g}(2) mode of the C{sub 60} molecule. A further increase in pressure up to 17 GPa does not induce significant new changes to the Raman spectra, while a decrease is accompanied by the reverse transformation at a pressure of about 2 GPa. The pressure dependence of the lattice parameters also exhibits a reversible feature at 2 GPa related to a jumplike decrease in compressibility. All these data are indicative of a phase transition in the vicinity of 2 GPa related to the formation of covalent bonds between C{sub 60} molecules and, probably, the appearance of C{sub 120} dimers in fullerene layers. It was also found that, in the pressure interval from 2 to 6.3 GPa, the Raman spectra of complexes exhibit photoinduced transformations under prolonged exposure to laser radiation with a wavelength of λ = 532 nm and power density up to 5000 W/cm{sup 2}. These changes are manifested by splitting and softening of the A{sub g}(2) mode and resemble analogous changes accompanying the photopolymerization of C{sub 60} fullerene. The intensity of new bands exhibits exponential growth with increasing exposure time. The photopolymer yield depends on both the laser radiation power and external pressure. The A{sub g}(2) mode splitting under irradiation can be related to the formation of photo-oligomers with various numbers of intermolecular covalent bonds per C{sub 60} molecule.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparison of electric and growth responses to excision in cucumber and pea seedlings. II. Long-distance effects are caused by the release of xylem pressure

Excision of a growing stem causes local wound responses, such as membrane depolarization and growth inhibition, as well as effects at larger distances from the cut. In this study, cucumber hypocotyls were excised 100 mm below the hook, so that the growing region was beyond the reach of the wound-induced depolarization (up to 40 mm). Even at such a distance, the cut still caused a considerable and rapid drop in the hypocotyl growth rate. This growth response is not a direct wound response because it does not result from the cut-induced depolarization and because it can be simulated by root pressure manipulation (using a pressure chamber). The results indicate that the growth response resulted from the rapid release of the xylem pressure upon excision. To test this conclusion we measured the xylem pressure by connecting a pressure probe to the cut surface of the stem. Xylem pressure (Px) was found to be +10 to +40 kPa in cucumber hypocotyls and -5 to -10 kPa or lower in pea epicotyls. Excision of the cucumber hypocotyl base led to a rapid drop in Px to negative values, whereas excision in pea led to a rapid rise in Px to ambient (zero) pressure. These fast and opposite Px changes parallel the excision-induced changes in growth rate (GR): a decrease in cucumber and a rise in pea. The sign of the endogenous xylem pressure also determined whether excision induced a propagating depolarization in the form of a slow wave potential (SWP). Under normal circumstances pea seedlings generated an SWP upon excision whereas cucumber seedlings failed to do so. When the Px in cucumber hypocotyls was experimentally inverted to negative values by incubating the cumber roots in solutions of NaCN or n-ethylmaleimide, excision caused a propagating depolarization (SWP). The experiment shows that only hydraulic signals in the form of positive Px steps are converted into propagating electric SWP signals. These propagating depolarizations might be causally linked to systemic 'wound' responses, which occur independently of the short-distance or direct wound responses.

Non-NASA Center↗

Pressure Drop-Flow Rate Curves for Single Phase Steam in Steam Generator U-tubes During Severe Accidents

Thermally induced steam generator tube rupture (TI-SGTR) can occur in pressurized water reactors (PWRs) with U-tube steam generators (SGs) during high pressure severe accident sequences resulting in containment bypass. Robust natural circulation patterns including in-vessel natural circulation and countercurrent flow to and from the SGs of superheated steam and other hot gases heats cooler structures in the reactor coolant system (RCS). The buoyancy driven flows return cooler and denser gases back to the core slowing the progression of some core degradation phenomena and failure of the lower head. As much as 50 percent of the decay energy and energy produced from core degradation oxidation reactions can be transported from the core to SGs resulting in the heat up and thermal creep of RCS pressure boundary components including hot leg nozzles, pressurizer surge line, and the SG tubes, many of which contain flaws. The creep failure of an individual tube is dependent on the transitory heating of the tube, a function of the mass flow rate through the tube and local temperature history of steam entering the tube. Buoyancy driven natural circulation flow rates are determined by changes in gravitational head, a combination of changes in fluid density due to heat transfer and change in elevation, and irreversible pressure drops resulting primarily from friction loss in the flow paths and other form losses. The nonuniform flow distribution in U-tubes of varying lengths and heights during single-phase liquid and two-phase natural circulation has been extensively studied in scaled test facilities and verified numerically in previous works. We hypothesize the countercurrent natural circulation of single-phase superheated steam in U-tube SGs is governed by the same characteristic pressure drop-flow rates curves of single-phase liquid and two-phase natural circulations in U-tubes connected to common plena derived in. Secondly, we propose flow distribution is a function of U-tube geometry - height, length, hydraulic diameter, etc., and the larger SGs of Combustion Engineering (CE) style 2 x 4 PWRs, which are the focus of this study, will show greater nonuniformity in tube by tube flow rates and ratio of forward flowing tubes to reverse flowing tubes. This work derives characteristic pressure drop-flow rate curves for single-phase superheated steam in CE-type SGs during a high pressure station blackout (SBO) sequence with failed auxiliary feedwater (AFW) and dry secondary side which is closely related to the TI-SGTR event. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Pressure-Dependent Thermal Expansion Coefficient by a Diamond Anvil Cell

A thermal expansion coefficient (αp) is an essential thermophysical quantity for high-pressure research. The thermal expansion coefficient is the volume change over the temperature in an isobaric heating process. Although isobaric heating processes for diamond anvil cell (DAC) have been conducted by keeping the pressure constant during heating, pressure determination at high-temperature high pressure is debatable for decades long. In this paper, a revertible heating/cooling approach is presented, while its pressure determination at high-temperature high pressure is not required. We report a pressure-dependent thermal expansion coefficient of MgO at 9.5 GPa by reversible heating/cooling was determined by a DAC and its result matches the one collected by a large volume press, whose isobaric heating was conducted by manually adjusting its load/pressure.

36 MATERIALS SCIENCE↗

Pressure‐Induced Structural and Magnetic Evolution in Layered Antiferromagnet YbMn 2 Sb 2

Electronic states under pressure exhibit unconventional spin and charge dynamics that provide a powerful route to uncover exotic phases in quantum materials. Here, we present the structural, magnetic, and electronic evolution of YbMn 2 Sb 2 under pressure. Single-crystal X-ray diffraction reveals a pressure-induced structural transition from the space group trigonal P$\overline{3}$m1 to the monoclinic P2 1 /m phase near 3.5 GPa, which remains stable up to 10 GPa. Magnetization measurements display an anomalously weak net magnetic moment and the absence of Curie–Weiss behavior up to 400 K, suggesting the formation of short-range Mn moment pairs that cancel macroscopically and subsequently evolve into long-range order upon cooling. Temperature-dependent resistivity shows semiconducting behavior with a transition at ∼119 K at ambient pressure, while pressure induces a dramatic suppression of resistance and the emergence of metallic-like temperature dependence, stabilized beyond 5 GPa. This pressure-driven semiconductor-metal transition is consistent with our density functional theory calculations, confirming the closing of the band gap under compression. Neutron diffraction under pressure identifies an incommensurate magnetic structure with antiparallel correlations between paired spins. Together, these results demonstrate how pressure-driven structural tuning and competing exchange interactions stabilize unconventional magnetic states in this low-dimensional magnetic semiconductor.

antiferromagnetic semiconductor↗

Comprehensive two-dimensional gas chromatography under low-pressure conditions

The analysis of thermally labile and high-boiling point compounds by gas chromatography (GC) can be a challenge. One technique to overcome these challenges is low-pressure GC, which uses the vacuum produced from the mass spectrometer and wide-bore columns to elute compounds at significantly lower temperatures. While GC-MS is a powerful technique, comprehensive two-dimensional gas chromatography (GC × GC), allows for resolution of compounds that would typically coelute using GC. Here, in this study, a pesticide standard mixture (8270 MegaMix Standard) was analyzed using a conventional GC × GC-TOFMS configuration (0.25 mm inner diameter (i.d.) to a 0.18 mm i.d. column) and low-pressure GC × GC-TOFMS configuration (0.53 mm i.d. to a 0.53 mm i.d. column). Elution temperatures, sensitivity, and peak capacity were investigated for both configurations. Compounds eluted an average of 30 °C less on the low-pressure GC × GC-TOFMS configuration compared to the conventional GC × GC-TOFMS configuration. Moreover, the compounds were separated in ~13 min on the low-pressure GC × GC-TOFMS as opposed to 33 min for conventional GC × GC-TOFMS. However, due to the wide-bore columns and faster runtimes the low-pressure GC × GC-TOFMS had a lower, β corrected 2D peak capacity, n c,β,2D , of 1260 while the conventional GC × GC-TOFMS was 3588. Interestingly, both configurations yielded a similar peak capacity production of 93 peaks/min and 107 peaks/min for low-pressure and conventional GC × GC-TOFMS, respectively. A “real world” sample of diesel fuel was tested on the low-pressure and conventional GC × GC-TOFMS configurations and similar results were obtained compared to the pesticide standard mix except the peak capacity production of the low-pressure GC × GC-TOFMS configuration was higher than that of the conventional GC × GC-TOFMS method.

47 OTHER INSTRUMENTATION↗

Stability study of aqueous foams under high-temperature and high-pressure conditions relevant to Enhanced Geothermal Systems (EGS)

In Enhanced Geothermal System (EGS) hydraulic fracturing is carried out by injecting cold water into deep Hot Dry Rocks (HDR) under carefully controlled conditions to create new or reopen existing fractures. Water-based fracturing fluids demonstrate some challenges including immense quantity of water usage, water sensitivity of the formations, water blocking, and lack of proppant carrying capacity and transportation. Thus, an alternative is to use foam-based fracturing fluid which offers potential advantage over conventional water-based fracturing fluid such as minimum water usage, reduced wellbore damage, high proppant carrying capacity, and less environmental damage. However, foams are complex mixture of gaseous phase and liquid phase which are thermodynamically unstable at downhole conditions, and their stability can decrease over time due to liquid drainage, bubble coarsening, and coalescence. This paper shows laboratory experiments executed to study foam stability at high temperature (200°C) and high pressure (6.9MPa) conditions which simulates the geothermal environment. Foam stability was characterized by half-life of foam, which is defined as the time taken by the foam to decreases by 50% of its original height due to drainage. In this paper, two types of gaseous phases, nitrogen (N 2 ) and carbon dioxide (CO 2 ) were investigated. Also, based on successful practice of foam-based fracturing fluid in oil and gas industries, four surfactants, including Alpha olefin sulfonate (AOS), Sodium dodecyl sulfonate (SDS), Tergitol™ (NP – 40), and Cetyltrimethylammonium chloride (CTAC) at optimum concentration of 1wt.% were tested for best stability performance. In addition, different stabilizing agents including guar gum, bentonite clay, crosslinker, silicon dioxide nanoparticles (SiO 2 ), graphene oxide (GO) were also studied. Experimental results showed that N 2 foams were more stable than CO 2 foams. It was observed that foam half-life decreased with the increase in temperature. Among all the surfactants, AOS foams showed the most promising thermal stability at high temperatures. Moreover, with the addition of stabilizing agents, foam's half-life was enhanced. Stabilizing agents such as crosslinker and GO dispersion showed the most stable foams with half-life recorded at 20min and 17min, respectively, at 200°C and 6.9MPa. Finally, pressure also showed a positive effect on foam stability; with increased pressure, foam half-life was increased. Based on the experimental data, analytical models for the effect of temperature and pressure were developed, considering foam degradation is a first-order kinetic reaction that linearly depends on the foam drainage mechanism. The effect of temperature on foam half-life was studied as an exponential decay model. In this model, foam half-life is a function of drainage rate constant (D A ) and activation energy (E a ) of the foam system. The effect of pressure on foam half-life was found to obey a power-law model where an increase in pressure showed an increase in foam half-life. Furthermore, a linear relation was studied for the effect of pressure on foam activation energy and drainage rate. Then the combined effects of temperature and pressure were studied, which yielded an analytical model to predict the foam stabilities in terms of half-life for different foam compositions. In conclusion, this research indicates that with an appropriate selection of surfactants and stabilizing agents, it is possible to obtain stable foams, which could replace conventional water fracturing fluid under EGS conditions.

15 GEOTHERMAL ENERGY↗

Exact solution of burst pressure for thick-walled pipes using the flow theory of plasticity

This paper develops an exact solution of burst pressure for defect-free, thick-walled pipes using the flow theory of plasticity in terms of the average shear stress yield criterion (or Zhu-Leis yield criterion). The pipe steel is assumed to obey the power-law strain hardening rule, and large plastic deformation is described by the finite strain theory. On this basis, internal pressure is obtained as a power series function of the effective strains on the inside and outside surfaces of the thick-walled pipe with use of the second Bernoulli numbers. At burst failure, the Zhu-Leis flow solution of burst pressure is determined as a power series solution, and the burst effective strains, the burst effective stresses, and the burst pressure are functions of the diameter ratio (D o / D i ), strain hardening exponent (n), and ultimate tensile strength (UTS). Similarly, the Tresca and von Mises flow solutions of burst pressure are also determined as a power series solution in terms of the Tresca and von Mises yield criteria. A general closed-from exact solution of burst pressure is then proposed for the three yield criteria, and the results showed that the proposed exact solution matches well with the power series solution for each yield criterion. Moreover, the von Mises flow solution is an upper bound prediction, the Tresca flow solution is a lower bound prediction, and the Zhu-Leis flow solution is an intermediate prediction that agrees well with the finite element analysis results of burst pressure for thick-walled pipes. Furthermore, two datasets of full-scale burst tests are then utilized to evaluate and validate the proposed flow solutions of burst pressure for both thin and thick-walled pipes.

42 ENGINEERING↗

Dynamic modeling studies of basin-scale pressure interference and CO 2 plume evolution in multi-well geologic CO 2 storage

This research employs numerical modeling to analyze how CO 2 plumes and pressure fronts evolve when CO 2 is injected into a single storage formation from multiple projects located in proximity. Here, this analysis also evaluates the extent to which injection well spacing alleviates pressure buildup in the absence of active pressure management tactics. The simulation approach was based on a single, homogenous saline aquifer in which CO 2 injection occurs under a one-injector baseline case and several multi-well cases where well spacing varies. Analysis results show that the extent of pressure buildup is in the range of tens or a few hundreds of kilometers and contingent upon the defining pressure buildup demarcating the front edge. For the geological setting evaluated in this paper, our analysis suggests that without active basin pressure management strategies, commercial-scale projects would likely need to be sited far apart to avoid pressure interference from one another. Analysis results show the radius of CO 2 plume varies approximately from 2 to 3 km from injection wells (each injecting 1 Mt/year for 30 years) depending on cases and modeling parameters assumed. Given the pressure interference, this paper thus draws attention to the importance of greater coordination among storage operators and regulatory stakeholders. Because this analysis assumes a very specific geologic setting, this exploratory analysis bears further investigations across other geologic scenarios.

42 ENGINEERING↗

High pressure phase transitions in scheelite structured fluoride: ErLiF{sub 4}

Our synchrotron based angle dispersive x-ray diffraction studies on scheelite structured ErLiF{sub 4} show that it undergoes two phase transitions, at ~11.5 and ~15.5 GPa to lower symmetry monoclinic phases, before becoming (irreversibly) amorphous at ~28 GPa. The first high pressure phase transformation to the fergusonite structure (space group I2/a) is found to be of thermodynamically second order. The second high pressure phase could be fitted to the P2/c space group, but detailed analysis rules out the wolframite structure (P2/c space group), common to many scheelite compounds under high pressures. We also suggest that despite the ionic character of the LiF{sub 4} tetrahedra, the compressibility of LnLiF{sub 4} (Ln=Eu–Lu) kind of scheelites is more affected by the LnF{sub 8} dodecahedra than the LiF{sub 4} tetrahedra. - Graphical abstract: Volume per formula unit of the scheelite and high pressure phases of ErLiF{sub 4} as a function of pressure. - Highlights: • ErLiF{sub 4} transforms to fergusonite and P2/c phase at high pressure. • Polyhedra of LnF{sub 8} affects compressibility of LnLiF{sub 4} (Ln=Eu–Lu) more than LiF{sub 4}. • Amorphization pressure varies inversely in LnLiF{sub 4} with ionic size of Ln cation. • In ErLiF{sub 4}a/c ratio reduces with pressure in contrast to reported increase in YLiF{sub 4}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electronic, elastic and dynamic properties of the filled tetrahedral semiconductor LiMgN under pressures

The electronic, elastic and dynamic properties of LiMgN under pressures have been studied using the plane wave pseudopotential method based on density functional theory within the local density approximation (LDA). The calculated lattice constants, bulk modulus and band gap values of the α phase LiMgN at normal conditions are in good agreement with the available experimental and theoretical results. Our GW corrected band gap values 3.190 eV (Γ–Γ) and 3.033 eV (Γ–X) are closer to the experimental data 3.20 eV. The variations of the band gap values, elastic constants, bulk modulus, shear modulus, Young's modulus, Poisson's ratio, elastic anisotropy, microhardness, Debye temperature and melting temperature with pressure for the α phase LiMgN are presented. The calculated phonon dispersion curves and the thermal properties entropy S and heat capacity C{sub V} have also been obtained. - Graphical abstract: The band gaps under pressures using LDA and GW method. - Highlights: • GW corrected band gap values at normal and high pressures are presented. • Mechanical stability, elastic anisotropy of LiMgN under pressures is analyzed. • Microhardness and melting temperatures of LiMgN under pressures is obtained. • Debye temperatures and dynamical stability under pressures are investigated. • Phonon dispersion curve, thermodynamic property under pressures is demonstrated.

36 MATERIALS SCIENCE↗

Effect of bed pressure drop on performance of a CFB boiler

The effect of bed pressure drop and bed inventory on the performances of a circulating fluidized bed (CFB) boiler was studied. By using the state specification design theory, the fluidization state of the gas-solids flow in the furnace of conventional CFB boilers was reconstructed to operate at a much lower bed pressure drop by reducing bed inventory and control bed quality. Through theoretical analysis, it was suggested that there would exist a theoretical optimal value of bed pressure drop, around which the boiler operation can achieve the maximal combustion efficiency and with significant reduction of the wear of the heating surface and fan energy consumption. The analysis was validated by field tests carried out in a 75 t/h CFB boiler. At full boiler load, when bed pressure drop was reduced from 7.3 to 3.2 kPa, the height of the dense zone in the lower furnace decreased, but the solid suspension density profile in the upper furnace and solid flow rate were barely influenced. Consequently, the average heat transfer coefficient in the furnace was kept nearly the same and the furnace temperature increment was less than 17{sup o}C. It was also found that the carbon content in the fly ash decreased first with decreasing bed pressure drop and then increased with further increasing bed pressure drop. The turning point with minimal carbon content was referred to as the point with optimal bed pressure drop. For this boiler, at the optimum point the bed pressure was around 5.7 kPa with the overall excess air ratio of 1.06. When the boiler was operated around this optimal point, not only the combustion efficiency was improved, but also fan energy consumption and wear of heating surface were reduced. 23 refs., 6 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Effect of externally applied pressure on rechargeable alkaline zinc batteries at limited depth of discharge

Rechargeable alkaline zinc batteries (AZBs) are being actively researched for grid-scale energy storage due to their safety, low toxicity, abundance, low cost, and ease-of-production. However, numerous studies on alkaline Zn–MnO 2 batteries have shown that issues such as heterogeneous Zn deposition, passivation, dendrite formation, hydrogen evolution, and formation of chemically irreversible byproducts on the electrode surfaces still limit their rechargeability. Several mitigating strategies have been proposed to improve the rechargeability of alkaline Zn–MnO 2 batteries, but the effect of pressure on electrochemical behavior has not been systematically investigated. In this paper, we demonstrate that an externally applied pressure at 20% MnO 2 depth-of-discharge (DOD MnO 2 ) has a profound effect on impedance, electrochemical cycling behavior, and materials morphology of alkaline Zn–MnO 2 batteries. Better electrochemical performance and improved morphology were achieved at 2.12 MPa pressure compared to 0.05 MPa pressure. Moreover, we examined the effect of externally applied pressure from 0 to 5.05 MPa before cycling and found that charge transfer resistance decreases significantly with pressure. Furthermore, we reported stable electrochemical cycling of MnO 2 ‖MnO 2 symmetric cells for 500 hours at 20% DOD under 2.12 MPa pressure. In conclusion, our efforts in understanding the effect of pressure could help design high performance and durable rechargeable alkaline Zn–MnO 2 batteries for grid-scale energy storage.

Rechargeable alkaline batteries↗

High-pressure x-ray diffraction study on the structure and phase transitions of the defect-stannite ZnGa[subscript 2]Se[subscript 4] and defect-chalcopyrite CdGa[subscript 2]S[subscript 4]

X-ray diffraction measurements on the sphalerite-derivatives ZnGa{sub 2}Se{sub 4} and CdGa{sub 2}S{sub 4} have been performed upon compression up to 23 GPa in a diamond-anvil cell. ZnGa{sub 2}Se{sub 4} exhibits a defect tetragonal stannite-type structure (I{bar 4}2m) up to 15.5 GPa and in the range from 15.5 to 18.5 GPa the low-pressure phase coexists with a high-pressure phase, which remains stable up to 23 GPa. In CdGa{sub 2}S{sub 4}, we find that the defect tetragonal chalcopyrite-type structure (I{bar 4}) is stable up to 17 GPa. Beyond this pressure a pressure-induced phase transition takes place. In both materials, the high-pressure phase has been characterized as a defect-cubic NaCl-type structure (Fm{bar 3}m). The occurrence of the pressure-induced phase transitions is apparently related with an increase in the cation disorder on the semiconductors investigated. In addition, the results allow the evaluation of the axial compressibility and the determination of the equation of state for each compound. The obtained results are compared to those previously reported for isomorphic digallium sellenides. Finally, a systematic study of the pressure-induced phase transition in 23 different sphalerite-related ABX{sub 2} and AB{sub 2}X{sub 4} compounds indicates that the transition pressure increases as the ratio of the cationic radii and anionic radii of the compounds increases.

36 MATERIALS SCIENCE↗