Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Factorization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Stress-intensity factors for two symmetric corner cracks

This paper presents stress-intensity factors, calculated by a three-dimensional finite-element analysis, for shallow or deep quarter-elliptical corner cracks at the edge of a hole in a finite-thickness plate. The plate was subjected to remote uniform tension, remote bending, or simulated pin loading in the hole; a wide range of configuration parameters was investigated. To verify the accuracy of the three-dimensional finite-element models employed, convergence was studied by varying the numbers of degrees of freedom. The stress-intensity factor variations along the crack front are compared with solutions from the literature.

Raju, I. S.↗
NASA NTRS1980

Simulation study of geometric shape factor approach to estimating earth emitted flux densities from wide field-of-view radiation measurements

A study was performed on the use of geometric shape factors to estimate earth-emitted flux densities from radiation measurements with wide field-of-view flat-plate radiometers on satellites. Sets of simulated irradiance measurements were computed for unrestricted and restricted field-of-view detectors. In these simulations, the earth radiation field was modeled using data from Nimbus 2 and 3. Geometric shape factors were derived and applied to these data to estimate flux densities on global and zonal scales. For measurements at a satellite altitude of 600 km, estimates of zonal flux density were in error 1.0 to 1.2%, and global flux density errors were less than 0.2%. Estimates with unrestricted field-of-view detectors were about the same for Lambertian and non-Lambertian radiation models, but were affected by satellite altitude. The opposite was found for the restricted field-of-view detectors.

Weaver, W. L.↗
NASA NTRS1979

Calibration procedures for measurement of reflectance factor in remote sensing field research

A means by which measurements of the optical properties of crops and soils can be knowledgeably compared from site to site and instrument to instrument is presented in detail. The definition of bidirectional reflectance factor is reviewed and discussed. Procedures for field implementation are illustrated and discussed. Spectral and goniometric properties of laboratory and field reference surfaces and typical environmental subjects serve as a basis for analysis of uncertainties introduced by differing illumination conditions. Results of a comparison of the performance of three spectrometer systems are presented and discussed. It is concluded that intelligent use of the bidirectional reflectance factor technique is an accurate and practical means to obtain the spectral, optical properties of crops and soils needed for advancements in agricultural remote sensing.

Robinson, B. F.↗
NASA NTRS1980

Transient stress intensity factors for edge and corner cracks in quench-test specimens

The transient temperature and stress fields in a quenched rectangular bar were computed and used to determine the stress intensity factors for midside and corner-edge cracks. The stress intensity factors, KI, are presented as a function of time, flaw size, and aspect ratio. The variations of KI along the crack edge are given and the self-limiting growth of the crack depth is discussed in relation to the nonlimited surface growth.

Emery, A. F.↗
NASA NTRS1982

Power-Factor Controller With Regenerative Braking

Modified power-factor motor-control circuit operates motor as a phase-controlled generator when load attempts to turn at higher than synchronous speed. An induction motor is required to act at times as a brake. Circuit modification allows power-factor controller to save energy in motoring mode and convert automatically to an induction-generator controller in generating, or braking, mode.

Nola, F. J.↗
NASA NTRS1982

Failure Detector for Power-Factor Controller

New protective circuits have been developed for power-factor ac motor controllers. Circuits prevent direct current and consequent motor heating that would normally result from failure of solid-state switch in controller. Single-phase power-factor controller with short detector compensates for short-circuit failure in either direction by applying full power to motor. Controller with open detector compensates for open-circuit failure in either direction by turning off power to motor.

Nola, F. J.↗
NASA NTRS1978

Shoreline as a controlling factor in commercial shrimp production

An ecological model was developed that relates marsh detritus export and shrimp production, based on the hypothesis that the shoreline is a controlling factor in the production of shrimp through regulation of detritus export from the marsh. LANDSAT data were used to develop measurements of shoreline length and area of marsh having more than 5.0 km shoreline/sq km for the coast of Louisiana, demonstrating the capability of remote sensing to provide important geographic information. These factors were combined with published tidal ranges and salinities to develop a mathematical model that predicted shrimp production for nine geographic units of the Louisiana coast, as indicated by the long term average commercial shrimp yield. The mathematical model relating these parameters and the shrimp production is consistent with an energy flow model describing the interaction of detritus producing marshlands with shrimp nursery grounds and inshore shrimping areas. The analysis supports the basic hypothesis and further raises the possibility of applications to coastal zone management requirements.

Faller, K. H.↗
NASA NTRS1981

Cold-air investigation of first stage of 4-1/2-stage, fan drive turbine with average stage-loading factor of 4.66

The design procedure and the development of the blading geometry for the 4 and 1/2 stage turbine are discussed. Results obtained with the first stage, operated as a single stage turbine, are presented. A free vortex design meets the design requirements without incurring problems such as excessive turning, negative reaction, or high Mach number. Cold air tests of the single stage turbine showed that the turbine developed design work (stage loading factor of 5.26) at an efficiency of 0.86, which was the efficiency predicted by a reference method. The mass flow at this condition was 0.88, which occurred at design speed and a pressure ratio of 1.407, corresponding to a stage loading factor of 4.35. The efficiency at this condition was 0.003 higher than that predicted by the reference method.

Whitney, W. J.↗
NASA NTRS1981

Stress-concentration factors for finite orthotropic laminates with a pin-loaded hole

Stresses were calculated for finite size orthotropic laminates loaded by a frictionless steel pin in a circular hole of the same diameter. The calculations were based on finite element analyses for six laminates. Stress concentration factors, based on nominal bearing stress, were determined for wide ranges of the ratios of width to diameter, w/d and edge distance to diameter, e/d. An infinite laminate case was analyzed for each laminate. Orthotropy had a significant influence on the tensile stress concentration at the hole. For example, the stress concentration factors for the infinite laminate cases ranged from 0.82 to 2.16, compared with 0.87 for the quasi-isotropic laminate. The finite widths and edge distances strongly influenced the tensile stress concentration. For the practical range w/d or = 3, the peak tensile stresses were as much as 80% larger than the infinite laminate reference value. For e/d or = 3, these stresses were amplified by as much as 50%. In contrast, the finite width and edge distance had little effect on shear-out and bearing stress concentrations.

Crews, J. H., Jr.↗
NASA NTRS1981

Power factor control system for ac induction motors

A power control circuit for an induction motor is disclosed in which a servo loop is used to control power input by controlling the power factor of motor operation. The power factor is measured by summing the voltage and current derived square wave signals.

Nola, F. J.↗
NASA NTRS1981

Approximate factorization for incompressible flow

For computational solution of the incompressible Navier-Stokes equations, the approximate factorization (AF) algorithm is used to solve the vectorized momentum equation in delta form based on the pressure calculated in the previous time step. The newly calculated velocities are substituted into the pressure equation (obtained from a linear combination of the continuity and momentum equation), which is then solved by means of line SOR. Computational results are presented for the NACA 66 sub 3 018 airfoil at Reynolds numbers of 1000 and 40,000 and attack angles of 0 and 6 degrees. Comparison with wind tunnel data for Re = 40,000 indicates good qualitative agreement between measured and calculated pressure distributions. Quantitative agreement is only fair, however, with the calculations somewhat displaced from the measurements. Furthermore, the computed velocity profiles are unrealistically thick around the airfoil, due to the excessive amount of artificial viscosity needed for stability. Based on the performance of the algorithm with regard to stability, it is concluded that AF/SOR is suitable for calculations at Reynolds numbers less than 10,000. Speedwise, the method is faster than point SOR by at least a factor of two.

Bernard, R. S.↗
NASA NTRS1980

Experimental and theoretical investigations of the quality factor for N/+/P silicon solar cells

Many N(+)P silicon solar cells made with silicon from different growth techniques have current-voltage relations of the form: I = I(0) (exp(qV/AkT) - 1), where the quality factor A is nonintegral, is greater than 1, and shows a temperature dependence. The dark forward characteristics of such cells have been measured over a range of temperatures and the behavior of the factor A derived from them. Lack of agreement with previous models has led to the development of a new model, in which N(+) conduction electrons tunnel to deep levels near that side, these levels being due to junction contamination by impurities. Electron recombination then occurs with holes thermally assisted into the junction from the P side. This mechanism involves increased I(0) values over those for diffusion diode processes and thus reduces the cell power conversion efficiency.

Garlick, G. F. J.↗
NASA NTRS1980

A pilot's assessment of helicopter handling-quality factors common to both agility and instrument flying tasks

Results from a series of simulation and flight investigations undertaken to evaluate helicopter flying qualities and the effects of control system augmentation for nap-of-the-earth (NOE) agility and instrument flying tasks were analyzed to assess handling-quality factors common to both tasks. Precise attitude control was determined to be a key requirement for successful accomplishment of both tasks. Factors that degraded attitude controllability were improper levels of control sensitivity and damping and rotor-system cross-coupling due to helicopter angular rate and collective pitch input. Application of rate-command, attitude-command, and control-input decouple augmentation schemes enhanced attitude control and significantly improved handling qualities for both tasks. NOE agility and instrument flying handling-quality considerations, pilot rating philosophy, and supplemental flight evaluations are also discussed.

Gerdes, R. M.↗
NASA NTRS1981

Factors controlling the occurrence of Pc 3 magnetic pulsations at synchronous orbit

The reported investigation has the purpose to extend the study of Pc 3 pulsations at synchronous orbit conducted by Arthur and McPherron (1977). A large data set is used with the goal of finding the factors related to the occurrence of Pc 3 pulsations at synchronous orbit. The results are compared with ground-based observations. The study demonstrates that the diurnal occurrence pattern has a maximum at a prenoon local time and shows a seasonal shift. Among the solar wind parameters, solar wind velocity and the direction of the IMF are found to be dominant factors. Attention is given to the analysis procedure, examples of 2-hour spectra, diurnal occurrence pattern, the correlation between solar wind parameters, and the solar wind stream structure and Pc 3 occurrence.

Takahashi, K.↗
NASA NTRS1981

Diurnal changes in reflectance factor due to Sun-row direction interactions

Over a two year period, data were collected regarding the canopies of soybeans grown in rows in planter boxes placed on a turntable in an effort to investigate changes in the spectral reflectance factor related to row direction, Sun direction, soil background, and crop development stage. Results demonstrate that the direction of rows in a soybean canopy can affect the reflectance factor of the canopy by as much as 230%. The results for the red spectral region tend to support the validity of canopy reflectance models; results for the infrared region do not.

Bauer, M. E.↗
NASA NTRS1981

Software metrics: The quantitative impact of four factors on work rates experienced during software development

A model of a software development process is described. The software development process is seen to consist of a sequence of activities, such as 'program design' and 'module development' (or coding). A manpower estimate is made by multiplying code size by the rates (man months per thousand lines of code) for each of the activities relevant to the particular case of interest and summing up the results. The effect of four objectively determinable factors (organization, software product type, computer type, and code type) on productivity values for each of nine principal software development activities was assessed. Four factors were identified which account for 39% of the observed productivity variation.

Gaffney, J. E., Jr.↗
NASA NTRS1981

Stimulation of body weight increase and epiphyseal cartilage growth by insulin like growth factor

The ability of insulin-like growth factor (IGF) to induce growth in hypophysectomized immature rats was tested by continuous infusion of the partially purified factor at daily doses of 6, 21, and 46 mU for an 8-day period. A dose-dependent growth of the proximal epiphyseal cartilage of the tibia and an associated stimulation of the primary spongiosa were produced by these amounts of IGF. The two highest doses of IGF also resulted in dose-dependent increases of body weight. Gel permeation of the sera at neutrality showed that the large-molecular-weight IGF binding protein was not induced by the infusion of IGF, whereas it ws generated in the sera of hypophysectomized rats that were infused with daily doses of 86 mU of human growth hormone.

Ellis, S.↗
NASA NTRS1981

An empirical stress-intensity factor equation for the surface crack

This paper presents an empirical stress-intensity factor equation for a surface crack as a function of parametric angle, crack depth, crack length, plate thickness and plate width for tension and bending loads. The stress-intensity factors used to develop the equation were obtained from a previous three-dimensional, finite-element analysis of semielliptical surface cracks in finite elastic plates subjected to tension or bending loads. A wide range of configuration parameters was included in the equation. The ratios of crack length to plate thickness and the ratios of crack depth to crack length ranged from 0 to 1.0. The effects of plate width on stress-intensity variations along the crack front were also included. The equation was used to predict patterns of surface-crack growth under tension or bending fatigue loads. The equation was also used to correlate surface-crack fracture data for a brittle epoxy material within + or - 10 percent for a wide range of crack shapes and crack sizes.

Newman, J. C., Jr.↗