Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Extreme Environment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

Design and performance validation of a high-temperature downhole permanent magnet generator used for an electro-pulse boring system in geothermal energy applications

Novel, direct-energy drilling technologies such as electro-pulse boring, have the potential to significantly increase the speed and depth of geothermal drilling but have not achieved widespread adoption due to several economic and technical barriers. One major challenge is that these drilling systems require electric power downhole. The current practice is to supply power to the drill string components by running electric cables down the geothermal well, but at the targeted well depths, this practice is cost-inhibitive, inefficient in terms of power consumption, and adds an additional failure point with the long cabling going through a highly corrosive, high-temperature environment. A solution to this problem is to develop high-temperature electric generator technology that can generate the required power downhole. Such a generator must also operate with high efficiency at the target downhole ambient temperature of 250 °C. In this paper, we investigate the various design considerations for this concept and subsequently design the downhole electric generator using a multi-objective design optimization approach. Through electromagnetic-, thermal- and short-circuit fault condition analysis, it is demonstrated that the optimized downhole electric generator concept presented in this paper can meet the performance requirements within this extreme drilling environment. Most remarkably, it is shown that a generator efficiency of 90% is achieved. In conclusion, to validate the results presented in this paper, a prototype generator is built and its performance is measured at 250 °C using a test bench uniquely developed for this application.

15 GEOTHERMAL ENERGY↗

Magnetism in metastable and annealed compositionally complex alloys

Compositionally complex materials (CCMs) present a potential paradigm shift in the design of magnetic materials. These alloys exhibit long-range structural order coupled with limited or no chemical order. As a result, extreme local environments exist with a large variations in the magnetic energy terms, which can manifest large changes in the magnetic behavior. In the current work, the magnetic properties of (Cr, Mn, Fe, Ni) alloys are presented. These materials were prepared by room-temperature combinatorial sputtering, resulting in a range of compositions with a single bcc structural phase and no chemical ordering. The combinatorial growth technique allows CCMs to be prepared outside of their thermodynamically stable phase, enabling the exploration of otherwise inaccessible order. The mixed ferromagnetic and antiferromagnetic interactions in these alloys causes frustrated magnetic behavior, which results in an extremely low coercivity (<1mT), which increases rapidly at 50 K. At low temperatures, the coercivity achieves values of nearly 500 mT, which is comparable to some high-anisotropy magnetic materials. Further, commensurate with the divergent coercivity is an atypical drop in the temperature dependent magnetization. These effects are explained by a mixed magnetic phase model, consisting of ferro-, antiferro-, and frustrated magnetic regions, and are rationalized by simulations. A machine-learning algorithm is employed to visualize the parameter space and inform the development of subsequent compositions. Annealing the samples at 600 °C orders the sample, more-than doubling the Curie temperature and increasing the saturation magnetization by as much as 5×. Simultaneously, the large coercivities are suppressed, resulting in magnetic behavior that is largely temperature independent over a range of 350 K. The ability to transform from a hard magnet to a soft magnet over a narrow temperature range makes these materials promising for heat-assisted recording technologies.

36 MATERIALS SCIENCE↗

Prediction and Enhancement of Thermal Protection Systems from Meteoroid Damage using a Smooth Particle Hydrodynamic Code

Interplanetary spacecraft are exposed to meteoroid fluxes that range in speeds from 10 to 72 km/sec, far above the capability of today’s test facilities to provide predictions for the likelihood of spacecraft critical penetration. Of special interest are sample return missions, which (though protected by shielding) must often survive years of exposure to the meteoroid environment in order to re-enter Earth’s atmosphere with their scientific cargo. This paper describes the simulation of meteoric material damage to thermal protection systems (TPS) housed beneath protective “garage” (shielding) enclosures using the Smooth Particle Hydrodynamics Code (SPHC) operated by the Institute for Defense Analyses and Stellingwerf Consulting in support of ongoing NASA tasks. The study outlined in this paper considered the impact effect of both meteoric materials such as iron, ice, and chondrites (dunnite), and non-meteoric materials such as aluminum and nylon against both external shielding materials (single and dual aluminum bumpers) and Heat shield for Extreme Entry Environments Technology (HEEET) TPS materials, used alone and in conjunction with shielding. A general predictive damage equation to HEEET TPS is developed from these SPHC simulations for velocities up to 70 km/sec.

Hypervelocity Impact, hydrocode, meteoroid and orb↗

In Situ Instrumentation for Sub-Surface Planetary Geochemistry

Novel instrumentation is under development at NASA's Goddard Space Flight Center, building upon earth-based techniques for hostile environments, to infer geochemical processes important to formation and evolution of solid bodies in our Solar System. A prototype instrument, the Pulsed Neutron Generator Gamma Ray and Neutron Detectors (PNG-GRAND), has a 14 MeV pulsed neutron generator coupled with gamma ray and neutron detectors to measure quantitative elemental concentrations and bulk densities of a number of major, minor and trace elements at or below the surfaces with approximately a meter-sized spatial resolution down to depths of about 50 cm without the need to drill. PNG-GRAND's in situ a meter-scale measurements and adaptability to a variety of extreme space environments will complement orbital kilometer-scale and in-situ millimeter scale elemental and mineralogical measurements to provide a more complete picture of the geochemistry of planets, moons, asteroids and comets.

Bodnarik, J.↗

Weibull and Bootstrap-Based Data-Analytics Framework for Fatigue Life Prognosis of the Pressurized Water Nuclear Reactor Component Under Harsh Reactor Coolant Environment

In general, the fatigue life of a safety critical pressure component is estimated using best-fit fatigue life curves (S-N curves). These curves are estimated based on underlying in-air condition fatigue test data. The best-fitting approach requires a large safety factor to accommodate the uncertainty associated with large scatter in fatigue test data. In addition to this safety factor, reactor component fatigue life prognostics requires an additional correction factor that in general is also estimated deterministically. This additional factor known as the environmental correction factor F en is to cater the effect of the harsh coolant environment that severely reduces the life of these components. The deterministic F en factor may also lead to further conservative estimation of fatigue life leading to unnecessary early retirement of costly reactor components. To address the above-mentioned issues, we propose a data-analytics framework which uses Weibull and Bootstrap probabilistic modeling techniques for explicitly quantifying the uncertainty/scatter associated with fatigue life rather than estimating the lives based on a best-fit based deterministic approach. We assume the proposed probabilistic approach would provide the first hand information for assessing the maximum and minimum effects of pressurized water reactor water on the reactor component. In the discussed approach, in addition to the probabilistic fatigue curves, we suggest using a probabilistic environment correction factor F en . Here, we assume the probabilistic fatigue curve and F en would capture the S-N data scatter associated with the bulk effect of material grades, surface finish, strain rate, etc. on the material/component fatigue life.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

High-Temperature-Performance Cyanate Ester Composites with Carboranes

Cyanate ester (CE) is an important class of materials among high-temperature performance thermosets. It is used in aerospace launch vehicles, heat sinks, booms, and trusses of satellites etc. due to its high glass transition temperatures (>220°C), excellent thermal stability, and low flammability. Current approaches to improve the thermal stability of CE include incorporation of siloxanes or phosphorus- based flame retardants (PFRs). In this work, we have explored boron-based hydroxy (PD) and epoxy (EP) functionalized carborane additives to improve the thermal properties of CE. Carborane fillers were solvent blended at various mass loadings in the resin and cured to study their effect on thermal properties. PD and EP carboranes react with CE to form iminocarbonate and oxazolidinone linkages respectively. Cure kinetics studies at different wt% loadings explained that carboranes catalyze the curing reaction by reducing curing activation energy by about 54% and 26% for 10 wt% loadings of PD and EP carboranes respectively. In addition, carborane-filled cyanate ester (CE) nanocomposites demonstrate an exceptionally high thermal stability as compared to the pristine resin in air and inert environment. Our thermogravimetric analysis (TGA) experiments show that the ultimate char yield of the resin can be increased from 0% to as high as 76% and 82% with 30 wt% PD and EP carborane loading respectively at 1000 °C in air. The initial degradation temperature T d;5 of the composites decreased with increasing carborane loadings in both air and argon. For instance, T d;5 for CE was 465 and 471.6 °C in argon and air while that for P20 was 437.4 and 452.1 °C. Modulated TGA studies gave evidence of the effect of carboranes on degradation kinetics and the mechanism of the resin in air and inert environment. The effect of bonding between carboranes and CE at various loadings on the thermal expansion of the matrix was also studied using Thermomechanical Analyzer (TMA). PD carborane reduced the T g for P20 to about 225 °C while CE had T g >350 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Parametric Analysis of Entry Vehicles for Giant Planet Missions

The Planetary Science Decadal Survey has identified Uranus and Saturn as high priori-ty destinations for a flagship and New Frontier missions respectively in the decade 2023-2032. The pro-posed presentation will focus on the entry and descent aspects of the entry vehicles design, considered as part of Giant Planet probe mission concepts, and associated trades for viable trajectory options. Giant Planet Entry Vehicle Parametric Study: Launch vehicle capabilities are evolving and provide an opportunity to increase instrumented probe dimensions. To assess the impact of larger aeroshell designs, a parametric study was conducted to understand the impact on aerothermal environments, TPS options, and TPS mass over a range of 1.0m to 2.0m aeroshell diameters for Uranus and Saturn probe concept missions. The 45° sphere-cone geometry is a legacy configuration that has demonstrated static stability and been used successfully in missions to Venus (Pioneer-Venus) and Jupiter (Galileo). A nose radius of 0.4 m was considered primarily to reduce the heat flux at the stagnation point compared to the smaller radii used in the Venus and Jupiter missions. Representative inertial velocities are chosen from a prior NASA Ames study. Viable entry trajectories to meet concept mission and science objectives were developed using the tool POST2. The newly developed thermal protection material called HEEET (Heatshield for Extreme Entry Environment Technology) was considered in the study. This material, which is at a technology readiness level (TRL) of 6, is highly customizable and available in two varieties: (i) a dual-layer version consisting of recession layer on top of an insulative layer, and (ii) a single-layer version consisting of the insulative layer alone, termed 3- dimensional Mid-Density Carbon Phenolic (3MDCP). Both options were considered for the forward heatshield (the sphere-cone part) in the pre-sent study.

Thermal Protection System↗

National Postirradiation Examination Workshop Report

A National Post-Irradiation-Examination (PIE) Workshop was held March 29-30, 2011, in Washington D.C., stimulated by the DOE Acting Assistant Secretary for Nuclear Energy approval on January 31, 2011 of the “Mission Need Statement for Advanced Post-Irradiation Examination Capability”. As stated in the Mission Need, “A better understanding of nuclear fuels and material performance in the nuclear environment, at the nanoscale and lower, is critical to the development of innovative fuels and materials required for tomorrow’s nuclear energy systems.” (2011) Developing an advanced post-irradiation capability is the most important thing we can do to advance nuclear energy as an option to meeting national energy goals. Understanding the behavior of fuels and materials in a nuclear reactor irradiation environment is the limiting factor in nuclear plant safety, longevity, efficiency, and economics. The National PIE Workshop is part of fulfilling or addressing Department of Energy (DOE) missions in safe and publically acceptable nuclear energy. Several presentations were given during the opening of the workshop. Generally speaking, these presentations established that we cannot continue to rely on others in the world to provide the capabilities we need to move forward with nuclear energy technology. These presentations also generally identified the need for increased microstructural understanding of fuels and materials to be coupled with modeling and simulation, and increased accessibility and infrastructure to facilitate the interaction between national laboratories and participating organizations. The overall results of the work of the presenters and panels was distilled into four primary needs 1. Understanding material changes in the extreme nuclear environment at the nanoscale. Nanoscale studies have significant importance due to the mechanisms that cause materials to degrade, which actually occur on the nanoscale. 2. Enabling additional proficiency in experimentation and analysis through robust modeling coupled with advanced characterization. 3. Advancing the infrastructure and accessibility of physical and administrative systems needed to meet the needs of participating organizations that are subject to different time cycles and constraints that make working and collaborating the national laboratories challenging. 4. Pursuing in-situ analysis and instrumentation to support the examination of dynamic changes to materials’ microstructure, deformation, and surface effects as they occur with time scales rather than the static comparison offered by current PIE methods. This Workshop Report responds to the research challenges for advanced/future PIE needs for nuclear materials development outlined by Energy Secretary Chu and the DOE-NE Research and Development Roadmap report, which was delivered to Congress in April 2010, (DOE-NE, 2010) by identifying the technial needs for fuel and material development specifically related to PIE. The information from the panels address these research challenges by identifying specific needs related to each of the topical areas. The focus of the Workshop was to identify gaps in the enabling capabilities for nuclear energy research and to identify high-priority fundamental capabilities to enable research to be completed that would likely have high impact on enabling nuclear energy as a significant contributor to energy production portfolios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanical Testing of PMCs under Simulated Rapid Heat-Up Propulsion Environments: In-Plane Compressive Behavior - II

Carbon fiber thermoset polymer matrix composites (PMC) with high temperature polyimide based in-situ polymerized monomer reactant (PMR) resin has been used for some time in applications which can see temperatures up to 550 F. Currently, graphite fiber PMR based composites are used in several aircraft engine components including the outer bypass duct for the GE F-404, exit flaps for the P&W F-100-229, and the core cowl for the GE/Snecma CF6-80A3. Newer formulations, including PMR-II-50 are being investigated as potential weight reduction replacements of various metallic components in next generation high performance propulsion rocket engines that can see temperatures which exceed 550 F. Extensive FEM thermal modeling indicates that these components are exposed to rapid heat-up rates (up to -200 F/sec) and to a maximum temperature of around 600 F. Even though the predicted maximum part temperatures were within the capability of PW-II-50, the rapid heat-up causes significant through-thickness thermal gradients in the composite part and even more unstable states when combined with moisture. Designing composite parts for such extreme service environments will require accurate measurement of intrinsic and transient mechanical properties and the hygrothermal performance of these materials under more realistic use conditions. The mechanical properties of polymers degrade when exposed to elevated temperatures even in the absence of gaseous oxygen. Accurate mechanical characterization of the material is necessary in order to reduce system weight while providing sufficient factors of safety. Historically, the testing of PMCs at elevated temperatures has been plagued by the antagonism between two factors. First, moisture has been shown to profoundly affect the mechanical response of these materials at temperatures above their glass transition temperature while concurrently lowering the material's Tg. Moisture phenomena is due to one or a combination of three effects, i.e., plastization of polymeric material by water, the internal pressure generated by the volatilization of water at elevated temperatures, and hydrolytic chemical decomposition. However, moisture is lost from the material at increasing rates as temperature increases. Second, because PMCs are good thermal insulators, when they are externally heated at even mild rates large thermal gradients can develop within the material. At temperatures where a material property changes rapidly with temperature the presence of a large thermal gradient is unacceptable for intrinsic property characterization purposes. Therefore, long hold times are required to establish isothermal conditions. However, in the service environments high-heating-rates, high temperatures, high-loading rates are simultaneous present along with residual moisture. In order to capture the effects of moisture on the material, holding at- temperature until isothermal conditions are reached is unacceptable particularly in materials with small physical dimensions. Thus, the effects due to moisture on the composite's mechanical characteristics, ie., their so-called analog response, may be instructive. One approach employed in this program was rapid heat-up (approx. 200 F/sec.) and loading of both dry and wet in-plane compressive specimens to examine the effects of moisture on this resin dominated mechanical property of the material.

Stokes, Eric H.↗

Enrichments for phototrophic bacteria and characterization by morphology and pigment analysis

The purpose of this investigation was to examine several sulfide containing environments for the presence of phototrophic bacteria and to obtain enriched cultures of some of the bacteria present. The field sites were Alum Rock State Park, the Palo Alto salt marsh, the bay area salt ponds, and Big Soda Lake (near Fallon, Nevada). Bacteria from these sites were characterized by microscopic examination, measurement of in vitro absorption spectra, and analysis of carotenoid pigments. Field observations at one of the bay area salt ponds, in which the salt concentration was saturating (about 30 percent NaCl) and the sediments along the shore of the pond covered with a gypsum crust, revealed a layer of purple photosynthetic bacteria under a green layer in the gypsum crust. Samples of this gypsum crust were taken to the laboratory to measure light transmission through the crust and to try to identify the purple photosynthetic bacteria present in this extremely saline environment.

Brune, D.↗

Terrestrial Proving Ground Capabilities Needed for Lunar In Situ Resource Utilization (ISRU) & Construction Concepts of Operation

Incorporating any new technology or system into a human exploration mission or architecture requires development well in advance of the mission to eliminate technology, cost, and schedule risk concerns. It is often stated that technologies need to be at a Technology Readiness Level (TRL) of 6, i.e. ‘system/subsystem model or prototype demonstration in a relevant environment (ground or space)’, by Authority To Proceed (ATP) or by the Preliminary Design Review (PDR) for the mission at the latest. There are two game changing capabilities for sustained human exploration of space that can have a significant effect on the overall exploration architecture and the technologies and systems included in the architecture. The first game changing capability, known as In Situ Resource Utilization (ISRU), involves the search for, acquisition, and processing of resources on the Moon and Mars into mission consumables and usable products, and the second is the ability to utilize space resources in the construction of roads, structures, and surface infrastructure. ISRU and surface construction capabilities have the potential to greatly reduce the cost and risk of human exploration while enabling sustained lunar surface and commercial operations. However, ISRU and surface construction systems are complex and must operate in extremely harsh environments, with abrasive regolith and pervasive dust, for long-periods of time, with potentially limited opportunities for maintenance and repair by humans. The complexity of these capabilities and operations also means that there are a limited number of companies that can design, build, and operate end-to-end systems on their own. The majority of the technologies being developed for these systems are by small companies and at the component or subsystem level. With the overarching strategy of the United States National Aeronautics and Space Administration (NASA) Space Technology Mission Directorate (STMD) to enable industry to implement ISRU and surface infrastructure for Artemis and space commercialization, it is therefore important to establish processes and capabilities to promote and foster collaborations among large and small companies involved in ISRU and surface infrastructure development. For ISRU and infrastructure systems and capabilities to be used in Artemis missions and future commercial lunar surface operations, a coordinated framework with virtual/physical integration and testing locations, or ‘Proving Grounds’, needs to be established and operated on a regular basis and open to all. This paper will discuss the ISRU and surface construction near and long-term concepts of operations, and review operations and lessons-learned from the previous ISRU analog field tests. From this information, requirements and capabilities will be proposed to support and enable the integration and testing of ISRU and construction systems with industry, academia, and international agencies, as well as what facilities and organizations could help establish these Proving Grounds.

ISRU↗

Atomic force microscopy spring constant determination in viscous liquids

The spring constant of cantilever in atomic force microscopy (AFM) is often calibrated from thermal noise spectra. Essential for accurate implementation of this 'thermal noise method' is an appropriate fitting function and procedure. Here, we survey the commonly used fitting functions and examine their applicability in a range of environments. We find that viscous liquid environments are extremely problematic due to the frequency dependent nature of the damping coefficient. The deviations from the true spring constant were sometimes more than 100% when utilizing the fit routines built into the three investigated commercial AFM instruments; similar problems can arise with homebuilt AFMs. We discuss the reasons for this problem, especially the limits of the fitting process. Finally, we present a thermal noise based procedure and an improved fit function to determine the spring constant with AFMs in fluids of various viscosities.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Charactarization of Thermal Protection Systems

In 2012, NASA's mission of landing the Mars Science Laboratory (MSL) on Mars was successful. MSL was protected by an ablative heatshield of tiled low density material known as PICA (phenolic impregnated carbon ablator). The heatshield was instrumented with MEDLI (MSL Entry Descent Landing Instrument) a suite of sensors & thermocouples at discrete locations in order to monitor the in-depth ablator temperature response and surface pressure. MEDLI was designed and developed by NASA Langley, in partnership with NASA Ames Research Center for the purposes of probing Mars and evaluating the performance of the spacecraft upon entry into the Martian atmosphere. The flight data reduces the uncertainty in engineer models for predicting the response of a spacecraft towards the extreme heating environment of an entry into the Martian atmosphere. MEDLI2 is a part of the Mars 2020 mission and is the next-generation sensor suite for entry, descent, and landing. This data will again help engineers validate their flight models. Additionally, the atmospheric data, can help us understand atmospheric density and winds. This is a critical study for reducing risks to both robotic and future human missions to Mars. Engineered models for Mars 2020 are dependent upon parameters related to the materials response to heating and radiation. In this work, the thermal properties and other measurements of various ablative materials are analyzed to achieve greater utility of the 2012 MEDLI flight data and more accurately determine the parameters being used in Mars 2020. The purpose of this study was to measure specific heat, thermal conductivity, char yield, reflectance as a function of wavelength, and other thermal parameters and optical properties of various ablative materials. CO2(g) at extreme temperatures emits radiation impacting MEDLI2 flight predictions. Emissivity & absorptivity as a function of temperature were calculated from FTIR and UV-Vis data as a means of investigating whether these materials might absorb CO2 radiation upon entry into the Mars atmosphere.

HEEET↗

Ultrasonic/Sonic Driller/Corer (USDC) as a Subsurface Sampler and Sensors Platform for Planetary Exploration Applications

The search for existing or past life in the Universe is one of the most important objectives of NASA's mission. For this purpose, effective instruments that can sample and conduct in-situ astrobiology analysis are being developed. In support of this objective, a series of novel mechanisms that are driven by an Ultrasonic/Sonic actuator have been developed to probe and sample rocks, ice and soil. This mechanism is driven by an ultrasonic piezoelectric actuator that impacts a bit at sonic frequencies through the use of an intermediate free-mass. Ultrasonic/Sonic Driller/Corer (USDC) devices were made that can produce both core and powdered cuttings, operate as a sounder to emit elastic waves and serve as a platform for sensors. For planetary exploration, this mechanism has the important advantage of requiring low axial force, virtually no torque, and can be duty cycled for operation at low average power. The advantage of requiring low axial load allows overcoming a major limitation of planetary sampling in low gravity environments or when operating from lightweight robots and rovers. The ability to operate at duty cycling with low average power produces a minimum temperature rise allowing for control of the sample integrity and preventing damage to potential biological markers in the acquired sample. The development of the USDC is being pursued on various fronts ranging from analytical modeling to mechanisms improvements while considering a wide range of potential applications. While developing the analytical capability to predict and optimize its performance, efforts are made to enhance its capability to drill at higher power and high speed. Taking advantage of the fact that the bit does not require rotation, sensors (e.g., thermocouple and fiberoptics) were integrated into the bit to examine the borehole during drilling. The sounding effect of the drill was used to emit elastic waves in order to evaluate the surface characteristics of rocks. Since the USDC is driven by piezoelectric actuation mechanism it can designed to operate at extreme temperature environments from very cold as on Titan and Europa to very hot as on Venus. In this paper, a review of the latest development and applications of the USDC will be given.

sampling↗

Recent Advances in the U.S. in Ablative TPS for In-situ Exploration of Giant Planets

The Decadal Survey report released [1] prioritizes Uranus as the highest priority Flagship class mission to be explored with an orbiter and a probe and it also recommended Saturn Probe under New Frontiers mission class. Thermal protection system (TPS) is essential for Uranus and Saturn probe missions. The two cardinal requirements are that it must be fail-safe and yet be mass efficient. The Decadal Survey report also pointed out the readiness of heatshield for extreme entry environment technology (HEEET) at TRL 6 for probe missions at Gas Giants. HEEET relies on 3-D weaving and is shown to be a robust and mass efficient TPS through ground testing and analysis. HEEET was matured to TRL 6 in 2019. HEEET was reported at the Ice Giant Workshop in 2019 at Marseille. Since 2019, significant advances have been made primarily because of Mars Sample Return (MSR) mission. MSR baselined 3-D Woven TPS as its heatshield for the earth entry system. MSR earth entry system (EES) requirements and the resulting heatshield/TPS requirements are most stringent of all entry missions. This is a result of backward contamination protection which classifies MSR as a “restricted class 5” mission to safeguard the accidental release of potentially hazardous Mars Sample into Earth’s atmosphere. Complex requirements for the heatshield start with micro-meteor impact tolerance followed by the requirement for steep entry to minimize the size of the impact footprint which results in extreme heating. The heatshield is part of the impact attenuation system. The EES architecture does not use a parachute and is designed to tolerate impact loads. Hence heatshield TPS selection and design becomes one of the key challenges. After completion of the HEEET technology maturation in 2019, IRAD efforts focused on assessing the 3-D Woven family of TPS to MSR EES. After nearly two years of evaluation of alternate TPS such as carbon phenolic, C-C hot structure, PICA, and 3-D woven family of TPS, a single layer 3-D woven TPS derived from the dual-layer HEEET was down selected and is currently the baseline. A new loom capable of weaving the single-layer 3-D woven preform at 80” wide has been designed, assembled and is currently on the verge of weaving the MSR EES TPS. During the HEEET maturation and the follow-on development, the single-layer TPS has been tested at extreme heating conditions. As a result, single layer TPS was recommended and evaluated during the Planetary Mission Concept Studies funded by NASA in preparation for the Decadal committee. In addition, in anticipation of Saturn mission proposals, single layer was evaluated as well. Aerocapture can reduce the trip time, also allow bigger payload fraction and in addition, it allows for the possibility of probe delivery once the spacecraft is in orbit. This can lead to obtaining both in-situ data as well as data from orbit simultaneously. Since Aerocapture depletes energy/velocity, probe delivery from orbit reduces the demand on TPS. Aerocapture was mentioned in the Decadal Study report as ready for implementation, but due to perceived risk it is not adopted by the mission designers. Establishing TPS readiness for aerocapture missions will be addressed. Going one step beyond aerocapture is aerogravity assist if fast return is the goal. Recent studies [4] looked at aerogravity assist and the TPS readiness. This talk will highlight both aerocapture and aerogravity assist from a TPS perspective. The main objective of this proposed talk is to present a comprehensive picture of the SOA TPS technology including recent developments. The talk will highlight advances in manufacturing, results from the Decadal White Papers, PMCS and other studies, and aerocapture and aerogravity assist that could play a role in the near or far term in-situ exploration.

E. Venkatapathy↗

Electricity generation by Pyrococcus furiosus in microbial fuel cells operated at 90°C

ABSTRACT Hyperthermophiles are microorganisms that thrive in extremely hot environments with temperatures near and even above 100°C. They are the most deeply rooted microorganisms on phylogenetic trees suggesting they may have evolved to survive in the early hostile earth. The simple respiratory systems of some of these hyperthermophiles make them potential candidates to develop microbial fuel cells (MFC) that can generate power at temperatures approaching the boiling point. We explored extracellular electron transfer in the hyperthermophilic archaeon Pyrococcus furiosus ( Pf ) by studying its ability to generate electricity in a two‐chamber MFC. Pf growing in defined medium functioned as an anolyte in a MFC operated at 90°C, generating a maximum current density of 2 A m −2 and a peak power density of 225 mW m −2 without the addition of any external redox mediator. Electron microscopy and electrochemical impedance spectroscopy of the anode with the attached Pf biofilm demonstrated bio‐electrochemical behavior that led to electricity generation in the MFC via direct electron transfer. This proof of concept study reveals for the first time that a hyperthermophile such as Pf can generate electricity in MFC at extreme temperatures. Biotechnol. Bioeng. 2017;114: 1419–1427. © 2017 Wiley Periodicals, Inc.

Sekar, Narendran↗

Converting existing optical detectors into fast x-ray detectors

Here, the very short burn time and small size of burning plasmas created at advanced laser-fusion facilities will require high-spatial-resolution imaging diagnostics with fast time resolution. These instruments will need to function in an environment of extremely large neutron fluxes that will cause conventional diagnostics to fail because of radiation damage and induced background levels. One solution to this challenge is to perform an ultrafast conversion of the x-ray signals into the optical regime before the neutrons are able to reach the detector and then to relay image the signal out of the chamber and into a shielded bunker, protected from the effects of these neutrons. With this goal in mind, the OMEGA laser was used to demonstrate high-temporal-resolution x-ray imaging by using an x-ray snout to image an imploding backlighter capsule onto a semiconductor. The semiconductor was simultaneously probed with the existing velocity interferometry system for any surface reflector (VISAR) diagnostic, which uses an optical streak camera and provided a one-dimensional image of the phase in the semiconductor as a function of time. The phase induced in the semiconductor was linearly proportional to the x-ray emission from the backlighter capsule. This approach would then allow a sacrificial semiconductor to be attached at the end of an optical train with the VISAR and optical streak camera placed in a shielded bunker to operate in a high neutron environment and obtain time-dependent one-dimensional x-ray images or time-dependent x-ray spectra from a burning plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enabling Experimental Evolution: Multi-Parameter Sensor System Integration into a Culture/Stressor Biofluidics System

Experimental evolution (EE) exposes microbial communities to ecological stressors, simulating dynamics up to near-extinction events. Combined with comparative sequencing and other molecular tools, such data can inform the genetic and other biological mechanisms underlying extremophile adaptation, and other observed effects. Automating this type of experiment using biofluidics can mitigate many traditional obstacles, including delays in assay results and environment adjustment and the need for many replicates. A first-generation device for automating EE procedures, the Automated Adaptive Directed Evolution Chamber (AADEC), was developed at NASA Ames. UV-C radiation was the stressor, an LED-photodiode array measured optical density, magnetic agitation and peristaltic pump systems ensured nutrient availability, and Arduino microcontrollers provided control. Escherichia coli in LB kanamycin media was used for testing and performance verification. A manual laboratory procedure with timed exposure to UV-C was performed to typify tolerance acquisition. Approximately a 106 factor increase in survival ratio was recorded over multiple iterations. Currently, a second-generation device is being developed integrating more real-time sensors: redox potential (ORP), indicating available/consumed metabolic energy; dissolved oxygen (DO), indicating aerobic/anaerobic growth; pH, indicating metabolic products; and electrical conductivity (EC), another indicator of metabolic products. The EC sensor system was constructed and calibrated in-house and matched commercial sensors in the required range. A Raspberry Pi computer automated the electrical system, allowing real-time data acquisition. The fluidics card was made of CNC-milled polycarbonate for biocompatibility. Each sensor parameter can also be used as a selection pressure alone or in combination with others to create extreme microbial environments. As a proof of concept, this work demonstrated sensor operation in one pair of growth-sensor chambers. It can be expanded to a multi-chamber system to enable inter-culture comparisons and multi-population studies. The prior Arduino system will be ported to the RPi system. Future stressors to be added include thermal, reactive oxygen species, and varying nutrient availability.

Govinda Raj, Chinmayee↗