Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

First Demonstration of Single-Mode Distributed Feedback Type-I GaSb Cascade Diode Laser Emitting near 2.9 µm

We demonstrate GaSb-based laterally-coupled distributed-feedback type-I cascade diode lasers emitting near 2.9 µm as potential sources for OH measurements. The laser heterostructures consist of two GaInAsSb quantum well stages in series separated by GaSb/AlSb/InAs tunnel junction and InAs/AlSb electron injectors. Single-mode emission is generated using second order lateral Bragg grating etched alongside narrow ridge waveguides. The lasers were fabricated into 2-mm-long devices, solder-mounted epi-up on copper submounts, and operate at room temperature. With an anti-reflection coating at the emission facet, the lasers exhibit a typical current threshold of 110 mA at 20 °C and emit more than 14 mW of output power. The Bragg wavelength temperature tuning rate was 0.29 nm/°C.

type-I↗

Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source

Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.

thermal nondestructive evaluation↗

Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source

Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.

thermal nondestructive evaluation↗

New analytic 1D pn junction diode transient photocurrent solutions following ionizing radiation and including time-dependent carrier lifetime degradation from a non-concurrent neutron pulse.

Circuit simulation codes, such as SPICE, are invaluable in the development and design of electronic circuits in radiation environments. These codes are often employed to study the effect of many thousands of devices under transient current conditions. Device-scale simulation codes are commonly used in the design of individual semiconductor components, but computational requirements limit their use to small-scale circuits. Analytic solutions to the ambipolar diffusion equation, an approximation to the carrier transport equations, may be used to characterize the transient currents at nodes within a circuit simulator. We present new analytic transient excess carrier density and photocurrent solutions to the ambipolar diffusion equation for 1-D abrupt-junction pn diodes. These solutions incorporate low-level radiation pulses and take into account a finite device geometry, ohmic fields outside the depleted region, and an arbitrary change in the carrier lifetime due to neutron irradiation or other effects. The solutions are specifically evaluated for the case of an abrupt change in the carrier lifetime during or after, a step, square, or piecewise linear radiation pulse. Noting slow convergence of the Fourier series solutions for some parameters sets, we evaluate portions of the solutions using closed-form formulas, which result in a two order of magnitude increase in computational efficiency.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

OLED Fundamentals: Materials, Devices, and Processing of Organic Light-Emitting Diodes

What is an organic light emitting diode (OLED)? Why should we care? What are they made of? How are they made? What are the challenges in seeing these devices enter the marketplace in various applications? These are the questions we hope to answer in this book, at a level suitable for knowledgeable non-experts, graduate students and scientists and engineers working in the field who want to understand the broader context of their work. At the most basic level, an OLED is a promising new technology composed of some organic material sandwiched between two electrodes. When current is passed through the device, light is emitted. The stack of layers can be very thin and has many variations, including flexible and/or transparent. The organic material can be polymeric or composed small molecules, and may include inorganic components. The electrodes may consist of metals, metal oxides, carbon nanomaterials, or other species, though of course for light to be emitted, one electrode must be transparent. OLEDs may be fabricated on glass, metal foils, or polymer sheets (though polymeric substrates must be modified to protect the organic material from moisture or oxygen). In any event, the organic material must be protected from moisture during storage and operation. A control circuit, the exact nature of which depends on the application, drives the OLED. Nevertheless, the control circuit should have very stable current control to generate uniform light emission. OLEDs can be designed to emit a single color of light, white light, or even tunable colors. The devices can be switched on and off very rapidly, which makes them suitable for displays or for general lighting. Given the amazing complexity of the technical and design challenges for practical OLED applications, it is not surprising that applications are still somewhat limited. Although organic electroluminescence is more than 50 years old, the modern OLED field is really only about half that age – with the first high-efficiency OLED demonstrated in 1987. Thus, we expect to see exciting advances in the science, technology and commercialization in the coming years. We hope that this book helps to advance the field in some small way. Contributors to this monograph are experts from top academic institutions, industry and national laboratories who provide comprehensive and up-to-date coverage of the rapidly evolving field of OLEDs. Furthermore, this monograph collects in one place, for the first time, key topics across the field of OLEDs, from fundamental chemistry and physics, to practical materials science and engineering topics, to aspects of design and manufacturing. The monograph synthesizes and puts into context information scattered throughout the literature for easy review in one book. The scope of the monograph reflects the necessity to focus on new technological challenges brought about by the transition to manufacturing. In the Section 1, all materials of construction of the OLED device are covered, from substrate to encapsulation. In Section 2, for the first time, additional challenges in devices and processing are addressed. This book is geared towards a broad audience, including materials scientists, device physicists, synthetic chemists and electrical engineers. Furthermore, this book makes a great introduction to scientists in industry and academia, as well as graduate students interested in applied aspects of photophysics and electrochemistry in organic thin films. This book is a comprehensive source for OLED R&D professionals from all backgrounds and institutions.

OLED↗

Smooth and vertical facet formation for AlGaN-based deep-UV laser diodes.

Using a two-step method of plasma and wet chemical etching, we demonstrate smooth, vertical facets for use in Al{sub x} Ga{sub 1-x} N-based deep-ultraviolet laser-diode heterostructures where x = 0 to 0.5. Optimization of plasma-etching conditions included increasing both temperature and radiofrequency (RF) power to achieve a facet angle of 5 deg from vertical. Subsequent etching in AZ400K developer was investigated to reduce the facet surface roughness and improve facet verticality. The resulting combined processes produced improved facet sidewalls with an average angle of 0.7 deg from vertical and less than 2-nm root-mean-square (RMS) roughness, yielding an estimated reflectivity greater than 95% of that of a perfectly smooth and vertical facet.

36 MATERIALS SCIENCE↗

Band Edge Control of Quasi–2D Metal Halide Perovskites for Blue Light–Emitting Diodes with Enhanced Performance

Perovskite light–emitting diodes (PeLEDs) have received great attention for their potential as next–generation display technology. While remarkable progress has been achieved in green, red, and near–infrared PeLEDs with external quantum efficiencies (EQEs) exceeding 20%, obtaining high performance blue PeLEDs remains a challenge. Poor charge balance due to large charge injection barriers in blue PeLEDs has been identified as one of the major roadblocks to achieve high efficiency. Here band edge control of perovskite emitting layers for blue PeLEDs with enhanced charge balance and device performance is reported. By using organic spacer cations with different dipole moments, that is, phenethyl ammonium (PEA), methoxy phenethyl ammonium (MePEA), and 4–fluoro phenethyl ammonium (4FPEA), the band edges of quasi–2D perovskites are tuned without affecting their band gaps. Furthermore, detailed characterization and computational studies have confirmed the effect of dipole moment modification to be mostly electrostatic, resulting in changes in the ionization energies of ≈0.45 eV for MePEA and ≈ –0.65 eV for 4FPEA based thin films relative to PEA–based thin films. With improved charge balance, blue PeLEDs based on MePEA quasi–2D perovskites show twofold increase of the EQE as compared to the control PEA based devices.

36 MATERIALS SCIENCE↗

Highly Efficient Pure‐Blue Light‐Emitting Diodes Based on Rubidium and Chlorine Alloyed Metal Halide Perovskite

Abstract Perovskite light‐emitting diodes (PeLEDs) are promising candidates for display and solid‐state lighting, due to their tunable colors, high conversion efficiencies, and low cost. However, the performance of blue PeLEDs is far inferior to that of the near‐infrared, red, and green counterparts. Here, the fabrication of pure‐blue PeLEDs with an emission peak at 475 nm, a peak external quantum efficiency of 10.1%, and a maximum luminance of 14 000 cd m −2 is demonstrated by tailoring the compositions of perovskites. The pure‐blue electroluminescence is achieved by simultaneous addition of rubidium and chlorine ions into CsPbBr 3 and incorporation of phenylethylammonium chloride forms quasi‐2D hybrid perovskites. The combination of these composition engineering results in blueshifted emissions without reducing the quantum yield. The judicious alloying is shown to be critical to result in the better morphology with suppressed current leakage and enhanced light outcoupling.

Yang, Yang↗

Efficient, Color-Stable, and Long-Lived White Organic Light-Emitting Diodes Utilizing Phosphorescent Molecular Aggregates

Highly efficient and stable single-stack hybrid white organic light-emitting diode (WOLED) devices are developed using two emissive layers: one with amber-colored phosphorescent molecular-aggregate emission from the Pd(II) complex, Pd(II) 7-(3-(pyridine-2-yl-κN)phenoxy-κC)(benzo-κC)([c]benzo[4,5]imidazo-κN)[1,2-a][1,5]naphthyridine, Pd3O8-Py5, and the other with blue fluorescence emission. Here, an optimized device structure achieves high color stability under various current densities, an external quantum efficiency (EQE) of 45.5%, a power efficiency of 97.4 Lm W -1 , and an estimated LT 95 (operational time to 95% of the initial luminance) of 50 744 h at an initial luminance of 1000 cd m -2 .

36 MATERIALS SCIENCE↗

Exciton Dynamics in Layered Halide Perovskite Light‐Emitting Diodes

Abstract Layered halide perovskites have garnered significant interest due to their exceptional optoelectronic properties and great promises in light‐emitting applications. Achieving high‐performance perovskite light‐emitting diodes (PeLEDs) requires a deep understanding of exciton dynamics in these materials. This review begins with a fundamental overview of the structural and photophysical properties of layered halide perovskites, then delves into the importance of dimensionality control and cascade energy transfer in quasi‐2D PeLEDs. In the second half of the review, more complex exciton dynamics, such as multiexciton processes and triplet exciton dynamics, from the perspective of LEDs are explored. Through this comprehensive review, an in‐depth understanding of the critical aspects of exciton dynamics in layered halide perovskites and their impacts on future research and technological advancements for layered halide PeLEDs is provided.

Baek, Sung‐Doo↗

Improved Light Extraction in Organic Light‐Emitting Diodes via Semiconductor Dilution

Increasing the internal light extraction efficiency of organic light‐emitting diodes (OLEDs) is key to improving their performance for solid‐state lighting applications; however, it is challenging to do this in a way that is compatible with high volume manufacturing. Here, it is shown that the outcoupling efficiency of OLEDs can be improved by diluting their hole transport layer (HTL) with the low refractive index material trifluoropropyl oligomeric silsesquioxane (F‐POSS). Specifically, co‐evaporating 40 vol.% F‐POSS in the HTL of single and multi‐stack phosphorescent OLEDs decreases its refractive index by Δ n ≈ 0.2, which in turn yields a ≈12% increase in their outcoupling efficiency with no impact on electrical performance or operational lifetime. This result is significant because F‐POSS is a small molecule that sublimes cleanly, does not aggregate, and is compatible with state‐of‐the‐art HTL materials, making it a realistic path to increase light extraction in commercial OLEDs manufactured on existing production lines.

36 MATERIALS SCIENCE↗

Magnetic Field Enhancement of Organic Light‐Emitting Diodes Based on Electron Donor–Acceptor Exciplex

Reverse intersystem crossing (RISC) from triplet to singlet states has been recently introduced to photophysics of organic chromophores. One type of RISC occurs in donor (D)–acceptor (A) composites that form an exciplex manifold in which the energy difference, Δ E ST between the lowest singlet (S 1 ) and triplet (T 1 ) levels of the exciplex is small (<100 meV) thus allowing RISC at room temperature. This adds a delayed component to the photoluminescence emission that is widely known as thermally activated delayed fluorescence. Here, it is found that the electroluminescence in organic light‐emitting diodes (OLED) based on electron D–A exciplex is significantly enhanced (up to ≈40%) by applying magnetic field, due to the existence of an additional spin‐mixing channel between singlet and triplet states in the exciplex. The large magneto‐electroluminescence (MEL) in N , N , N ′, N ′‐tetrakis(4‐methoxyphenyl)benzidine: tris‐[3‐(3‐pyridyl)mesityl]borane [D–A] based OLEDs is demonstrated. These results are supported by magneto‐photoluminescence (MPL) measurements, and density functional theory calculations. Importantly, it is found that both MEL and MPL are thermally activated indicating the dominant role of the RISC process. The MEL( B ) response using the Δ g mechanism is analyzed, where the electron and hole g ‐values are different from each other because they reside in different molecules.

Basel, Tek↗

Mitigation of Electrical Failure of Silver Nanowires under Current Flow and the Application for Long Lifetime Organic Light-Emitting Diodes

Here, the extended lifetime of organic light-emitting diodes (OLEDs) based on enhanced electrical stability of a silver nanowire (AgNW) transparent conductive electrode is reported. Specifically, in depth investigation is performed on the ability of atomic layer deposition deposited zinc oxide (ZnO) on AgNWs to render the nanowires electrically stable during electrical stressing at the range of operational current density used for OLED lighting. ZnO-coated AgNWs have been observed to show no electrical, optical, or morphological degradation, while pristine AgNW electrodes have become unusable for optoelectronic devices due to dramatic decreases in conductivity, transparency, and fragmentation of the nanowire network at ≈150 mA cm -2 . When fabricated into OLED substrates, resulting OLEDs fabricated on the ZnO-AgNW platform exhibit a 140% increase in lifetime when compared to OLEDs fabricated on indium tin oxide (ITO)/glass, and ≈20% when compared to OLEDs fabricated on AgNW based substrates. While both ZnO-coated and pristine AgNW substrates outperform ITO/glass due to the lower current densities required to drive the device, morphological stability in response to current stressing is responsible for the enhancement of lifetime of ZnO-AgNW based OLEDs compared to pristine AgNW based OLEDs.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Defect-Enabled Electrical Current Leakage in Ultraviolet Light-Emitting Diodes

The AlGaN materials system offers a tunable, ultra-wide bandgap that is exceptionally useful for high-power electronics and deep ultraviolet optoelectronics. Moseley et al. (pp. 723–726) investigate a structural defect known as an open-core threading dislocation or ''nanopipe'' that is particularly detrimental to devices that employ these materials. Furthermore, an AlGaN thin film was synthesized using metal-organic chemical-vapor deposition. Electrical current leakage is detected at a discrete point using a conductive atomic-force microscope (CAFM). However, no physical feature or abnormality at this location was visible by an optical microscope. The AlGaN thin film was then etched in hot phosphoric acid, and the same location that was previously analyzed was revisited with the CAFM. The point that previously exhibited electrical current leakage had been decorated with a 1.1 μm wide hexagonal pit, which identified the site of electrical current leakage as a nanopipe and allows these defects to be easily observed by optical microscopy. Moreover, with this nanopipe identification and quantification strategy, the authors were able to correlate decreasing ultraviolet light-emitting diode optical output power with increasing nanopipe density.

36 MATERIALS SCIENCE↗