Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94

A study of compressed spatially non-Gaussian optical pulses from mode-locked lasers.

The effect of the grating-induced phase and spatial modulations by multiple transverse modes simultaneously present in mode-locked laser pulses is investigated. Our analysis shows that the dispersions of the grating pair become strongly dependent on wavelength because of the energy exchanges occurring among transverse modes. As a result, the maximum-intensity trace at the output of the grating is shown to be curved and the grating-induced pulse-compression rate is shown to vary significantly across the beam cross section. Also, a discussion is presented relating our analysis to existing experimental data on the wavelength-dependent chirping rates of mode-locked laser beams.

Kim, D. M.↗

SEASAT observations of lithospheric flexure seaward of trenches

Lithospheric flexure seaward of deep ocean trenches in SEASAT altimeter observations of the marine geoid. In fact, mechanical models of lithospheric flexure can be tested directly on the SEASAT altimeter data. A simple elastic model was used for the oceanic lithosphere and, after least squares adjustments, estimates of model parameters were recovered including Outer Rise (OR) amplitude, OR wavelength, and effective lithospheric thickness. Effective lithospheric thickness was recovered for five regions: the Mariana, the Kuril, the Philippine, the Aleutian and the Middle America OR. These results support the suggestion of Bodine et al. (1981) that effective thickness, T, increased with age of lithosphere in approximate accord with the relation T approximately equals x age to the 1/2 power where C approximately equals 4 km x my to the -1/2 power. Altimetric results agree more closely with this relation than do published results based on bathymetric data. The close agreement with the thickness-age relation suggests that there is no longer any need to assume that significant horizontal compression acts across the Kuril, Marianas and Izo-Bonin trenches. This thickness-age relation implies that flexural strength of the oceanic lithosphere is temperature controlled.

Mcadoo, D. C.↗

Pulsations in magnetic field and ion flux observed at L = 4.5 on August 5, 1972

Observations made from space (Explorer 45) near L = 4.5 and from magnetic observatories on the ground of the large-amplitude ULF pulsations that followed the unusually strong compression of the earth's magnetosphere associated with the geomagnetic storm of August 1972 are analyzed. A spectral analysis of Explorer 45 magnetometer data indicates a compressional mode oscillation coupled to a transverse mode oscillation. Enhancements in amplitude of a 300-s period wave near 0040 UT August 5 are found to coincide with an intensification of 100- to 1000-Hz magnetic and electric field oscillations and with the appearance of fluxes of energetic ions. It is noted that during this period the ion pitch angle distribution in each available energy channel (24-300 keV) followed a periodic sequence, apparently synchronized with the magnetic pulsations, from normal trapping (highest fluxes near 90 deg and lowest near 0 deg and 180 deg) to a nearly isotropic particle distribution. It is found that during the transitions the particle flux near 90 deg pitch angle was alternately large earthward of the satellite (before isotropy) and larger radially outward from the satellite (after isotropy).

Engebretson, M. J.↗

Seasat observations of lithospheric flexure seaward of trenches

Lithospheric flexure seaward of deep ocean trenches is evident in Seasat altimeter observations of the marine geoid. In fact, mechanical models of lithospheric flexure can be tested directly on the Seasat altimeter data. A simple elastic model has been used for the oceanic lithosphere and, after least squares adjustments, estimates have been recovered of model parameters including outer rise (OR) amplitude, OR wavelength, and effective lithospheric thickness. Effective lithospheric thicknesses have been recovered for six regions: the Mariana, the Kuril, the Philippine, the Aleutian, the Izu-Bonin, and the Middle America OR's. These results support the proposition that effective thickness Te increases with age of lithosphere in approximate accord with the relation Te approximately C x square root of age where C approximately 4 km/square root of (m.y.). In fact, altimetric results agree more closely with this relation than do published results based on bathymetric data. The close agreement with the thickness-age relation suggests that there is no longer any need to assume that significant horizontal compression acts across the Kuril, Marianas, and Izu-Bonin trenches. This thickness-age relation implies that flexural strength of the oceanic lithosphere is temperature controlled.

Mcadoo, D. C.↗

The behaviour of a compressible turbulent boundary layer under incipient separation conditions

This paper presents an experimental study of a turbulent boundary-layer/shock-wave interaction. The interaction was generated by a two-dimensional compression corner, and the flow was on the point of separating. Measurements were made using both normal and inclined hot wires, and the data include measurements of the longitudinal mass-flow fluctuation intensity and the mass-weighted Reynolds shear stress.

Muck, K. C.↗

Space shuttle descent design: From development to operations

The descent guidance system, the descent trajectories design, and generating of the associated flight products are discussed. The programs which allow the successful transitions from development to STS operations, resulting in reduced manpower requirements and compressed schedules for flight design cycles are addressed. The topics include: (1) continually upgraded tools for the job, i.e., consolidating tools via electronic data transfers, tailoring general purpose software for needs, easy access to tools through an interactive approach, and appropriate flexibility to allow design changes and provide growth capability; (2) stabilizing the flight profile designs (I-loads) in an uncertain environment; and (3) standardizing external interfaces within performance and subsystems constraints of the Orbiter.

Crull, T. J.↗

Computation of separated flow on a ramp using the space marching conservative supra-characteristics method

Steady, hypersonic viscous flows over compression corners with streamwise separation have been computed using the space marching Conservative Supra-Characteristics Method (CSCM-S) of Lombard. The CSCM-S method permits stable space marching of the parabolized Navier-Stokes (PNS) equations through large separated flow regions. The present method has been used to compute surface pressure, heat transfer, and skin friction coefficients for two compression corner cases studied experimentally by Holden and Moselle. The computed results compare favorably with previous Navier-Stokes results and the experimental data. The present method has also been compared with the conventional Beam-Warming scheme for solving the PNS equations. Comparison are made for accuracy, computer time, and computer storage.

Stookesberry, D. C.↗

Information technologies for astrophysics circa 2001

It is easy to extrapolate current trends to see where technologies relating to information systems in astrophysics and other disciplines will be by the end of the decade. These technologies include miniaturization, multiprocessing, software technology, networking, databases, graphics, pattern computation, and interdisciplinary studies. It is less easy to see what limits our current paradigms place on our thinking about technologies that will allow us to understand the laws governing very large systems about which we have large data sets. Three limiting paradigms are as follows: saving all the bits collected by instruments or generated by supercomputers; obtaining technology for information compression, storage, and retrieval off the shelf; and the linear model of innovation. We must extend these paradigms to meet our goals for information technology at the end of the decade.

Denning, Peter J.↗

Effect of Angle of Attack and Exit Nozzle Design on the Performance of a 16-inch Ram Jet at Mach Numbers from 1.5 to 2.0

An investigation of the performance of a 16-inch ram jet engine having a single oblique-shock all-external compression inlet designed for a flight Mach number of 1.8, was conducted in the NACA Lewis 8-by 6-foot supersonic wind tunnel. Data were obtained at Mach numbers from 1.5 to 2.0 and angles of attack from 0 degrees to 10 degrees. Three exit nozzles were used; a cylindrical extension of the combustion chamber, a 4 degrees half-angle converging nozzle with a 0.71 contraction ratio, and a graphite converging-diverging nozzle having a 0.71 contraction ratio plus reexpansion to essentially major body diameter.

EXITS↗

A comparison of two incompressible Navier-Stokes algorithms for unsteady internal flow

A comparative study of two different incompressible Navier-Stokes algorithms for solving an unsteady, incompressible, internal flow problem is performed. The first algorithm uses an artificial compressibility method coupled with upwind differencing and a line relaxation scheme. The second algorithm uses a fractional step method with a staggered grid, finite volume approach. Unsteady, viscous, incompressible, internal flow through a channel with a constriction is computed using the first algorithm. A grid resolution study and parameter studies on the artificial compressibility coefficient and the maximum allowable residual of the continuity equation are performed. The periodicity of the solution is examined and several periodic data sets are generated using the first algorithm. These computational results are compared with previously published results computed using the second algorithm and experimental data.

Wiltberger, N. Lyn↗

Improved Hypersonic Inlet Performance Using Validated Strut Compression Designs

Aerojet is currently executing two Strutjet propulsion contracts: one a Rocket Based Combined Cycle (RBCC) engine for a NASA-Marshall Space Flight Center (MSFC) Advanced Reusable Transportation Technology (ARTT) program, the second a Dual Mode Ram/Scramjet engine for a USAF Wright Laboratories Storable Fuel Scramjet Flow Path Concepts program. The engines employed in both programs operate at supersonic and low hypersonic speeds and use inlets employing forebody external and sidewall compression. Aerojet has developed and validated a successful design methodology applicable to these inlet types. Design features include an integrated vehicle forebody, external side compression struts, strut sidewall and throat bleed, a throat shock trap, and variable geometry internal contraction. Computation Fluid Dynamic (CFD) predictions and test data show these inlets allow substantially increased flow turning angles over other designs. These increased flow turning angles allow shorter and lighter engines than current designs, which in turn enables higher performing vehicles with broad operating characteristics. This paper describes the designs of two different inlets evaluated by the NASA-MSFC and USAF programs, discusses the results of wind tunnel tests performed by NASA-Lewis Research Center, and provides correlations of test data with CFD predictions. Parameters of interest include low Mach number starting capability, start sensitivity as a function of back pressure at various contraction ratios, flow turning angles, strut and throat bleed effects, and pressure recovery at various Mach numbers.

Bulman, M. J.↗

Strain Gage Loads Calibration Testing of the Active Aeroelastic Wing F/A-18 Aircraft

This report describes strain-gage calibration loading through the application of known loads of the Active Aeroelastic Wing F/A-18 airplane. The primary goal of this test is to produce a database suitable for deriving load equations for left and right wing root and fold shear; bending moment; torque; and all eight wing control-surface hinge moments. A secondary goal is to produce a database of wing deflections measured by string potentiometers and the onboard flight deflection measurement system. Another goal is to produce strain-gage data through both the laboratory data acquisition system and the onboard aircraft data system as a check of the aircraft system. Thirty-two hydraulic jacks have applied loads through whiffletrees to 104 tension-compression load pads bonded to the lower wing surfaces. The load pads covered approximately 60 percent of the lower wing surface. A series of 72 load cases has been performed, including single-point, double-point, and distributed load cases. Applied loads have reached 70 percent of the flight limit load. Maximum wingtip deflection has reached nearly 16 in.

Lokos, William A.↗

The Imager for Mars Pathfinder Insurance Pan

The Imager for Mars Pathfinder (IMP) obtained a full panorama of the Sagan Memorial Station landing site on Sol 2, before the IMP mast was deployed. The images in this panorama were taken in 4 filters (including stereo) and losslessly compressed to provide a high-quality multispectral survey of the landing site even if the IMP mast did not successfully deploy; this data set was therefore called the Insurance Pan. It was completed late in the afternoon of Sol 2, just before the IMP mast was (successfully) deployed. The data were stored in memory and returned to Earth after it became clear that downlink rates were higher than expected. The Insurance Pan horizontal (azimuth) coverage is nearly complete, with gaps caused by pointing errors and data packet losses. Stereo data were acquired in the blue (445 nm) filter, as well as right-eye green (531 nm), orange (600 nm), and near-infrared (752 nm) data.

K E Herkenhoff↗

Expansion of direction space around the cardinal axes revealed by smooth pursuit eye movements

It is well established that perceptual direction discrimination shows an oblique effect; thresholds are higher for motion along diagonal directions than for motion along cardinal directions. Here, we compare simultaneous direction judgments and pursuit responses for the same motion stimuli and find that both pursuit and perceptual thresholds show similar anisotropies. The pursuit oblique effect is robust under a wide range of experimental manipulations, being largely resistant to changes in trajectory (radial versus tangential motion), speed (10 versus 25 deg/s), directional uncertainty (blocked versus randomly interleaved), and cognitive state (tracking alone versus concurrent tracking and perceptual tasks). Our data show that the pursuit oblique effect is caused by an effective expansion of direction space surrounding the cardinal directions and the requisite compression of space for other directions. This expansion suggests that the directions around the cardinal directions are in some way overrepresented in the visual cortical pathways that drive both smooth pursuit and perception.

Visual Pathways/physiology↗

Characterization of Composite Fan Case Resins

The majority of commercial turbine engines that power today s aircraft use a large fan driven by the engine core to generate thrust which dramatically increases the engine s efficiency. However, if one of these fan blades fails during flight, it becomes high energy shrapnel, potentially impacting the engine or puncturing the aircraft itself and thus risking the lives of passengers. To solve this problem, the fan case must be capable of containing a fan blade should it break off during flight. Currently, all commercial fan cases are made of either just a thick metal barrier or a thinner metal wall surrounded by Kevlar-an ultra strong fiber that elastically catches the blade. My summer 2004 project was to characterize the resins for a composite fan case that will be lighter and more efficient than the current metal. The composite fan case is created by braiding carbon fibers and injecting a polymer resin into the braid. The resin holds the fibers together, so at first using the strongest polymer appears to logically lead to the strongest fan case. Unfortunately, the stronger polymers are too viscous when melted. This makes the manufacturing process more difficult because the polymer does not flow as freely through the braid, and the final product is less dense. With all of this in mind, it is important to remember that the strength of the polymer is still imperative; the case must still contain blades with high impact energy. The research identified which polymer had the right balance of properties, including ease of fabrication, toughness, and ability to transfer the load to the carbon fibers. Resin deformation was studied to better understand the composite response during high speed impact. My role in this research was the testing of polymers using dynamic mechanical analysis and tensile, compression, and torsion testing. Dynamic mechanical analysis examines the response of materials under cyclic loading. Two techniques were used for dynamic mechanical analysis. The ARES Instrument analyzed the material through torsion. The second machine, TA Instruments apparatus, applied a bending force to the specimen. These experiments were used to explore the effects of temperature and strain rate on the stiffness and strength of the resins. The two different types of loading allowed us to verify our results. An axial-torsional load frame, manufactured by MTS Systems, Inc., was used to conduct the tensile, compression, and torsional testing. These tests were used to determine the stress-strain curves for the resins. The elastic and plastic deformation data was provided to another team member for characterization of high fidelity material property predictions. This information was useful in having a better understanding of the polymers so that the fan cases could be as sturdy as possible. Deformation studies are the foundation for the computational modeling that provides the structural design of a composite engine case as well as detailed analysis of the blade impact event.

Dvoracek, Charlene M.↗

Safety Aboard the International Space Station

As with any task that NASA takes on, safety is of utmost importaqce. There are pages of safety codes and procedures that must be followed before any idea can be brought to life. Unfortunately, the International Space Station s (ISS) safety regulations and procedures are based on lg standards rather than on Og. To aide in making this space age home away from home a less hazardous environment, I worked on several projects revolving around the dangers of flammable items in microgravity. The first task I was assigned was to track flames. This involves turning eight millimeter video recordings, of tests run in the five second drop tower, into avi format on the computer. The footage is then compressed and altered so that the flame can be seen more clearly. Using another program called Spotlight, line profiles were used to collect data describing the luminescence of the flame at different points. These raw data are saved as text files and run trough a macro so that a Matlab program can analyze it. By fitting the data to a curve and determining the areas of brightest luminescence, the behavior of the flame can be recorded numerically. After entering the data into a database, researchers can come back later and easily get information on flames resulting from different gas and liquid mixtures in microgravity. I also worked on phase two of the FATE project, which deals with safety aboard the ISS. This phase involves igniting projected droplets and determining how they react with secondary materials. Such simulations represent, on a small scale, the spread of onboard fires due to the effervescence of burning primary materials. I set up existing hardware to operate these experiments and ran tests with it, photographing the results. I also made CAD drawings of the apparatus and the area available on the (SF)2 rig for it to fit into. The experiment will later be performed on the KC-135, and the results gathered will be used to reanalyze current safety standards for the ISS, including the distance of required separation for flammable materials. Additional information is included in the original extended abstract.

Mintz, Shauna M.↗

Constitutive Soil Properties for Unwashed Sand and Kennedy Space Center

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle. This report provides constitutive material models for one soil, unwashed sand, from NASA Langley's gantry drop test facility and three soils from Kennedy Space Center (KSC). The four soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LS-DYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The four soil models are intended to be specific to the soil conditions discussed in the report. The unwashed sand model represents clayey sand at high density. The KSC models represent three distinct coastal sand conditions: low density dry sand, high density in-situ moisture sand, and high density flooded sand. It is possible to approximate other sands with these models, but the results would be unverified without geotechnical tests to confirm similar soil behavior.

Thomas, Michael A.↗

Constitutive Soil Properties for Cuddeback Lake, California and Carson Sink, Nevada

Accurate soil models are required for numerical simulations of land landings for the Orion Crew Exploration Vehicle. This report provides constitutive material modeling properties for four soil models from two dry lakebeds in the western United States. The four soil models are based on mechanical and compressive behavior observed during geotechnical laboratory testing of remolded soil samples from the lakebeds. The test specimens were reconstituted to measured in situ density and moisture content. Tests included: triaxial compression, hydrostatic compression, and uniaxial strain. A fit to the triaxial test results defines the strength envelope. Hydrostatic and uniaxial tests define the compressibility. The constitutive properties are presented in the format of LS-DYNA Material Model 5: Soil and Foam. However, the laboratory test data provided can be used to construct other material models. The four soil models are intended to be specific only to the two lakebeds discussed in the report. The Cuddeback A and B models represent the softest and hardest soils at Cuddeback Lake. The Carson Sink Wet and Dry models represent different seasonal conditions. It is possible to approximate other clay soils with these models, but the results would be unverified without geotechnical tests to confirm similar soil behavior.

Thomas, Michael A.↗