Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CHARTS - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,693 records · Page 94
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

A study of the pitching moments and the stability characteristics of monoplanes

This note presents a study of the pitching moments and the stability characteristics of monoplanes. Expressions for the pitching-moment coefficient and the Diehl stability coefficient for the monoplane are developed, suitable for the use of airplane designers. The effective difference between the high-wing and low-wing types is portrayed and discussed. Comparisons between experimental and computed values are made. Charts for use in the solution of numerical values of the pitching-moment and stability coefficients are presented.

Higgins, George J↗
NASA NTRS1936

A method of estimating the aerodynamic effects of ordinary and split flaps of airfoils similar to the Clark Y

An empirical method is given for estimating the aerodynamic effect of ordinary and split flaps on airfoils similar to the Clark Y. The method is based on a series of charts that have been derived from an analysis of existing wind-tunnel data. Factors are included by which such variables as flap location, flap span, wing aspect ratio, and wing taper may be taken into account. A series of comparisons indicate that the method would be suitable for use in making preliminary performance calculations and in structural design.

Pearson, H A↗
NASA NTRS1936

A General Tank Test of a Model of the Hull of the British Singapore IIC Flying Boat

A general test was made in the N.A.C.A. tank of a 1/12-size model of the hull of the British Singapore IIC flying boat loaned by the Director of Research, British Air Ministry. The results are given in charts and are compared with the results of tests of a model of an American flying-boat hull, the Sikorsky S-40. The Singapore hull has a greater hump resistance but a much lower high-speed resistance than the S-40.

Dawson, John R↗
NASA NTRS1936

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and had but a slight effect on the spray characteristics. For approximately the same angles of dead rise the resistance of the pointed-step hulls were considerably lower at high speeds than those of the more conventional hulls.

Dawson, John R↗
NASA NTRS1936

The Reduction of Aileron Operating Force by Differential Linkage

It is shown that the control force of ordinary ailerons may be reduced to zero over a range of deflections and at a given flight condition by the use of an appropriate differential movement. Approximations to the ideal motion obtainable with a simple linkage are discussed and a chart that enables the selection of an appropriate crank arrangement is presented. Various aspects of the practical application of the system are discussed and it is concluded that a small fixed tab, deflected to trim both ailerons upward, would be advantageous.

Jones, Robert T↗
NASA NTRS1937

Free-spinning Wind-tunnel Tests of a Low-wing Monoplane with Systemic Changes in Wings and Tails

A series of tests was made at the National Advisory Committee for Aeronautics (NACA) free-spinning tunnel to determine the effect of systematic changes in wing and tail arrangement upon steady-spinning and recovery characteristics of a conventional low-wing monoplane model for a basic loading condition. Eight wings and three tails, covering a wide range of aerodynamic characteristics, were independently ballasted so as to be interchangeable with no change in mass distribution. For each of the 24 wing-tail combinations, observations were made of steady spins for four control settings and of recoveries for five control manipulators. The results are presented in the form of charts comparing the spin characteristics. The results showed that, with a poor tail arrangement, wing plan form and tip shape had a considerable effect on the spinning characteristics.

Seidman, Oscar↗
NASA NTRS1937

Pressure drop in tubing in aircraft instrument installations

The theoretical basis of calculation of pressure drop in tubing is reviewed briefly. The effect of pressure drop in connecting tubing upon the operation and indication of aircraft instruments is discussed. Approximate equations are developed, and charts and tables based upon them are presented for use in designing installations of altimeters, air-speed indicators, rate-of-climb indicators, and air-driven gyroscopic instruments.

Wildhack, W A↗
NASA NTRS1938

Hydrodynamic and Aerodynamic Tests of Four Models of Outboard Floats : (N.A.C.A. Models 51-A, 51-B, 51-C, and 51-D)

Four models of outboard floats (N.A.C.A. models 51-A, 51-B, 51-C, and 51-D) were tested in the N.A.C.A. tank to determine their hydrodynamic characteristics and in the 20-foot wind tunnel to determine their aerodynamic drag. The results of the tests, together with comparisons of them, are presented in the form of charts. From the comparisons, the order of merit of the models is estimated for each factor considered. The best compromise between the various factors seems to be given by model 51-D. This model is the only one in the series with a transverse step.

Dawson, John R↗
NASA NTRS1937

Static Thrust Analysis of the Lifting Airscrew

This report presents the results of a combined theoretical and experimental investigation conducted at the Georgia School of Technology on the static thrust of the lifting air screw of the type used in modern autogiros and helicopters. The theoretical part of this study is based on Glauert's analysis but certain modifications are made that further clarify and simplify the problem. Of these changes the elimination of the solidity as an independent parameter is the most important. The experimental data were obtained from tests on four rotor models of two, four, and five blades and, in general, agree quite well with the theoretical calculations. The theory indicates a method of evaluating scale effects on lifting air screws, and these corrections have been applied to the model results to derive general full-scale static thrust, torque, and figure-of-merit curves for constant-chord, constant-incidence rotors. Convenient charts are included that enable hovering flight performance to be calculated rapidly.

Knight, Montgomery↗
NASA NTRS1938

Hydrodynamic and Aerodynamic Tests of Models of Floats for Single-float Seaplanes NACA Models 41-D, 41-E, 61-A, 73, and 73-A

Tests were made in the NACA tank and in the NACA 7 by 10 foot wind tunnel on two models of transverse step floats and three models of pointed step floats considered to be suitable for use with single float seaplanes. The object of the program was the reduction of water resistance and spray of single float seaplanes without reducing the angle of dead rise believed to be necessary for the satisfactory absorption of the shock loads. The results indicated that all the models have less resistance and spray than the model of the Mark V float and that the pointed step floats are somewhat superior to the transverse step floats in these respects. Models 41-D, 61-A, and 73 were tested by the general method over a wide range of loads and speeds. The results are presented in the form of curves and charts for use in design calculations.

Parkinson, J B↗
NASA NTRS1939

Hydrodynamic and Aerodynamic Tests of a Family of Models of Seaplane Floats with Varying Angles of Dead Rise - N.A.C.A. Models 57-A, 57-B, and 57-C

Three models of V-bottom floats for twin-float seaplanes (N.A.C.A. models 57-A, 57-B, and 57-C) having angles of dead rise of 20 degrees, 25 degrees, and thirty degrees, respectively, were tested in the N.A.C.A. tank and in the N.A.C.A. 7- by 10-foot wind tunnel. Within the range investigated, the effect of angle of dead rise on water resistance was found to be negligible at speeds up to and including the hump speed, and water resistance was found to increase with angle of dead rise at planing speeds. The height of the spray at the hump speed decreased with increase in angle of dead rise and the aerodynamic drag increased with dead rise. Lengthening the forebody of model 57-B decreased the water resistance and the spray at speeds below the hump speed. Spray strips provided an effective means for the control of spray with the straight V sections used in the series but considerably increased the aerodynamic drag. Charts for the determination of the water resistance and the static properties of the model with 25 degrees dead rise and for the aerodynamic drag of all the models are included for use in design.

Parkinson, John B↗
NASA NTRS1934

Effect of retractable-spoiler location on rolling- and yawing-moment coefficients

In this report are presented the results of wind-tunnel tests of retractable spoilers on the upper surface of a Clark Y wing, which have been made as part of an investigation of lateral control devices being conducted by the National Advisory Committee for Aeronautics. Spoilers with chords up to 15.0 percent of the wing chord were tested in several locations on a plain rectangular wing and in two locations on the same wing equipped with a 20.0 percent chord split flap down 60 degrees. Charts are given for four representative angles of attack from which values of rolling- and yawing-moment coefficients may be obtained for spoilers up to 15.0 percent chord located on the upper surface of a Clark Y wing. The tests showed that at low angles of attack practically the same rolling moments can be obtained with a given spoiler at any location back of 30.0 percent of the wing chord, while at high angles of attack there is a definite advantage in locating the spoiler at least as far forward as 30.0 percent of the chord. The yawing moments accompanying a given rolling moment increase positively as the spoiler location is moved forward from the trailing edge of the wing. It is concluded that the 30.0 percent chord location is probably the optimum provided that instantaneous response of the airplane to a control movement can be obtained.

Shortal, J A↗
NASA NTRS1941

Velocity gained and altitude lost in recoveries from inclined flight paths

A series of charts is given showing the variation of the velocity gained and the altitude lost in dive pullouts with the initial indicated air speed and the dive angle. The effects of the maximum load factor, the drag parameter K, the initial altitude, and the type of recovery on the velocity gained and the altitude lost are also considered. The results were obtained from a step-by-step solution of the equations of motion in which mean values of the air density and the airplane drag coefficient were used. The load-factor variation with time is arbitrarily specified in various ways to simulate pull-out procedures, some of which might be encountered in flight.

Pearson, H A↗
NASA NTRS1939

The Frequency of Torsional Vibration of a Tapered Beam

A solution for the equation of torsional vibration of tapered beams has been found in terms of Bessel functions for beams satisfying the following conditions: (a) the cross sections along the span are similar in shape; and (b) the torsional stiffness of a section can be expressed as a power of a linear function of distance along the span. The method of applying the analysis to actual cases has been described. Charts are given from which numerical values can be immediately obtained for most cases of practical importance. The theoretical values of the frequency ratio have been experimentally checked on five beams having different amounts of taper.

Coleman, Robert↗
NASA NTRS1941

Analysis of Ground Effect on the Lifting Airscrew

A study is presented of ground effect as applied to the lifting airscrew of the type used in modern gyroplane and helicopters. The mathematical analysis of the problem has been verified by tests made of three rotor models in the presence of a large circular "ground plane." A method of approximating the decelerating effect during vertical approach to the ground has been devised. The results of the study are presented in the form of convenient charts.

Knight, Montgomery↗
NASA NTRS1942

A Comparison of the Results from General Tank Tests of 1/6- and 1/12-full-size Models of the British Singapore IIC Flying Boat

A 1/6-full-size model of the hull of the British Singapore IIC flying boat was tested in the NACA tank. The results are given in the form of charts and are compared with the results of previous tests made in the NACA tank of a 1/12-full-size model, published in NACA T.N. No. 580, and with the results of tests made in the British R.A.E. tank of another 1/6-full-size model of the same hull. When the data from the tests of the 1/6- and 1/12-full-size models were compared on the basis of Froude's law of comparison, differences were found. This fact supported the belief that the small scale of the model and the use of a model that was too small to suit the equipment of the NACA tank had caused the results of the tests of the 1/12-full-size model to be less reliable than the results of the tests of the 1/6-full-size model. The results of the tests of the two models agreed sufficiently well to show that test of a small model, if made meticulously and with suitable equipment, may give useable results, but that a larger model should be used whenever feasible. The results of the NACA tests of the 1/6-full-size model were found to be in good agreement with the R.A.E. tests of a model of the same size.

Truscott, Starr↗
NASA NTRS1947

Column and Plate Compressive Strengths of Aircraft Structural Martials Extruded 0-1HTA Magnesium Alloy

Column and plate compressive strengths of extruded 0-1HTA magnesium alloy were determined both within and beyond the elastic range from tests of flat end H-section columns and from local instability tests of H-, Z-, and channel section columns. These tests are part of an extensive research investigation to provide data on the structural strength of various aircraft materials. The results are presented in the form of curves and charts that are suitable for use in the design and analysis of aircraft structures.

Heimerl, George J↗
NASA NTRS1947

Free-falls and parachute descents in the standard atmosphere

A detailed table of the standard equilibrium velocity and standard equilibrium time is presented for bodies falling in the standard atmosphere. This table gives the velocity at various altitudes and the time of fall from sea level to -4000 feet and from 80,000 feet to sea level. In addition to this standard table, there are given short tables and charts of an open-parachute descent and free-falls; the terminal velocity at sea level, and the variation of the weight-to-drag ratio (2w/cds)1/2 for various weight jumpers from 90 to 30 feet in open-parachute descent; and estimations of drag coefficients of silk and nylon parachutes. The table of standard equilibrium velocities and standard equilibrium times may be used directly for open-parachute descents, given the weight of the jumper, the diameter of the parachute, and the drag coefficient. For free-falls starting from horizontal flight, approximately 14 seconds must be added to the equilibrium time given in the table to obtain the total time to sea level. (author)

Webster, A P↗