Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “units”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Geospatial Characterization of Low-Temperature Heating and Cooling Demand in the United States

Geothermal resources at temperatures below 150 degrees C have great potential as energy sources for various direct-use applications including heating and cooling in residential and commercial buildings. This study geospatially quantifies U.S. heating and cooling demand in residential, commercial, and manufacturing sectors; heating demand in the agricultural sector; and cooling demand in data centers at the county level through end-use energy consumption, expenditure, and commissioned power analyses. Heating and cooling demand in the residential sector was estimated using energy consumption data obtained from the U.S. Energy Information Administration accounting for different U.S. climate zones. For commercial sector analysis, the end-use major fuel energy intensity at the census division level was disaggregated to the county level with respect to principal building activities. Heating and cooling demand analysis for the manufacturing sector was based on end-use energy consumption for direct-use total process categorized by the North America Industry Classification System. Fuel expenditures in the U.S. Department of Agriculture Farm Production Expenditures were examined for heating demand analysis in the agricultural sector, particularly for the greenhouse, nursery, and floriculture production category. Lastly, commissioned power for data centers in the United States were explored for cooling demand analysis. Results indicated a significant fraction of U.S. primary energy consumption is used for low-temperature heating and cooling applications. Heating and cooling demand in residential and commercial sectors is significantly affected by the number of housing units and climate zone designations, while heating and cooling demand in manufacturing and agricultural sectors and data centers are mainly dependent on the number of facilities and their locations. Maps were generated visualizing where heating and cooling demand is high and, overlain with geothermal resource maps, can indicate locations where geothermal energy can supply this heating and cooling demand.

cooling demand↗

Combining complex flow manifold with three dimensional woven lattices as a thermal management unit

The present invention is directed to a manifold for directing cooling fluid and/or gas to a heat exchanger in a flow configuration designed to optimize heat transfer from the heat exchanger. The manifold can take many different forms such as a layered construction with distributed inlet paths, local outlet paths, a central collection changer and a path for fluid removal. The manifold can be formed from a metal, plastic, rubber, ceramic, or other heat resistant material known to or conceivable by one of skill in the art. The manifold can also be combined with any type of heat exchanger known to or conceivable by one of skill in the art to form a thermal management unit. To optimize overall properties such as low pressure drop, high heat transfer, and excellent temperature uniformity of the thermal management unit, the manifold can be graded, expanded and scaled as needed.

Hemker, Kevin J.↗

Nuclear-Integrated Energy Units: Advancing Cybersecurity for Resilient Energy Systems

Rapidly increasing usage of nuclear-integrated energy units has created new challenges in terms of cybersecurity. This paper discusses the potential cyberthreat challenges and cyber risks associated with the widespread adoption of these units, and the role of artificial intelligence (AI) and machine learning (ML) techniques in enhancing the security and resilience of these systems.

20 FOSSIL-FUELED POWER PLANTS↗

Heat pumps in the United States: Market potentials, challenges and opportunities, technology advances

The US heat pump market has been affected by the socioeconomic impacts of the COVID-19 pandemic. However, the Biden administration’s goal of net-zero greenhouse gas emissions by 2050 through electrification and clean energy technologies is accelerating the research, development, and deployment of heat pumps in the United States for improved energy performance, reduced greenhouse gas emissions, and wider adoption. The US heat pump market has experienced steady growth since 2010. In 2020, heat pumps surpassed gas furnace shipments for the first time, and the trend maintains through 2022. The current priority is to improve the affordability of energy and equitable access to heat pump technologies through cost reductions and further accelerate this trend. In addition, current R&D includes emphases on alternative refrigeration technology and lower–global warming potential refrigerants to reduce direct emissions. Heat pump market share is expected to grow as regulatory policies and financial incentives steer the building sector toward decarbonization. This paper reviews policies and market trends, discusses the challenges and opportunities in the current policy landscape, and reviews current research in the United States.

Malhotra, Mini↗

J.K. Spruce power plant, Unit 1, San Antonio, Texas

CPS Energy's J.K. Spruce power plant, Unit 1 was recently recognised by the EUCG Fossil Productivity Committee as the best performer in the large coal plant category over the 2002-2006 evaluation period. The competition was tough, with more than 80 plants in the running, but Unit 1 emerged as the clear winner by earning top points for high plant reliability and very low nonfuel O & M costs. It meets its environmental goals when burning PRB coal in its tangentially fired furnace with recently upgraded low NOx burners, overfire air and a new combustion control system. A baghouse and wet flue gas desulfurization system clean up combustion products. 3 photos.

01 COAL, LIGNITE, AND PEAT↗

A story of revival: United Coal's East Gulf preparation plant

Some say beauty is in the eye of the beholder, but when United Coal purchased the assets of White Mountain Mining in late 2005, the attractiveness of the acquired assets did not require much debate. Whilst the Pocahontas Coal reserves included in the acquisition were very desirable for producing coke, the East Gulf preparation plant was in poor condition. In order to minimize cost, maintenance and manpower whilst increasing production, the circuits in the existing plant were modified and the Barvoy Vessel was replaced with a single, pump fed, 30-inch Krebs HM cyclone. A spiral circuit was added as were screen bowl centrifuges. Finally the plant was given a structural upgrade and a new siding was installed. With the East Gulf restoration project complete, the United Coal Co. (UCC) and Pocahontas Coal are now considering expanding the Affinity complex. 2 figs., 6 photos.

01 COAL, LIGNITE, AND PEAT↗

Two 3D networks based on sandwich-type polyoxometalate units linked by Sr-O clusters: Synthesis, structure, and magnetic property

Two 3D hybrid sandwich-type polyoxometalates, [{l_brace}Sr(H{sub 2}O){sub 5}Sr(H{sub 2}O){sub 6}Sr{sub 0.5}(H{sub 2}O){sub 7{r_brace}2}Mn{sub 4}(H{sub 2}O){sub 2}({alpha}-PW{sub 9}O{sub 34}){sub 2}].6H{sub 2}O (1) and [{l_brace}Sr(H{sub 2}O){sub 6}[Sr(H{sub 2}O){sub 8}]{sub 2}Sr(H{sub 2}O){sub 4{r_brace}2}Mn{sub 4}(H{sub 2}O){sub 2}({alpha}{beta}{beta}{alpha}-P{sub 2}W{sub 15}O{sub 56}){sub 2}].5H{sub 2}O (2), have been obtained by the routine synthetic reactions in aqueous solution and characterized by IR, elemental analysis, thermal analysis, and X-ray single-crystal diffraction. The 3D hybrid framework of 1 and 2 are built by tetra-Mn{sup II} substituted sandwich-type polyoxotungstates modified by fourteen Sr(H{sub 2}O){sub x} (x=4-8) units acting as bridges, forming centrosymmetric sandwich structures. The magnetic property of compound 1 has been studied by measuring its magnetic susceptibility in the temperature range of 2-300 K, which indicates predominant ferromagnetic interactions between the Mn{sup II}-O-Mn{sup II} bridge unit. Additionally, the electrochemical behaviours have been detected on solid bulk modified carbon paste electrodes of compounds (CPEs) and three redox couples are detected. - Graphical abstract: Two compounds based on Keggin(a) and Wells-Dawson(b) polyoxometalates modified by 14 Sr-O clusters.

36 MATERIALS SCIENCE↗

Evaluating Electric Vehicle Public Charging Utilization in the United States Using the EV WATTS Dataset: Preprint

The utilization of electric vehicle (EV) charging in the United States is a rapidly evolving puzzle further complicated by changes in travel habits brought on by the global COVID-19 pandemic. The EV WATTS dataset is the largest publicly available dataset on the utilization of EV charging in the United States and provides key insights into the changing patterns of public vehicle charging and vehicle use as EV range increases, commute patterns evolve, and more infrastructure becomes available.

ADVANCED PROPULSION SYSTEMS↗

HTTR criticality calculations with SCALE6: Studies of various geometric and unit-cell options in modeling

The fuel element of the High Temperature Engineering Test Reactor (HTTR) presents a doubly heterogeneous geometry, where tiny TRISO fuel particles dispersed in a graphite matrix form the fuel region of a cylindrical fuel rod, and a number of fuel rods together with moderator or reflector then constitute the lattice design of the core. In this study, a series of full-core HTTR criticality calculations were performed with the SCALE6 code system using various geometric and unit-cell options in order to systematically investigate their effects on neutronic analysis. Two geometric descriptions (ARRAY or HOLE) in SCALE6 can be used to construct a complicated and repeated model. The result shows that eliminating the use of HOLE in the HTTR geometric model can save the computation time by a factor of 4. Four unit-cell treatments for resonance self-shielding corrections in SCALE6 were tested to create problem-specific multigroup cross sections for the HTTR core model. Based on the same ENDF/B-VII cross-section library, their results were evaluated by comparing with continuous-energy calculations. The comparison indicates that the INFHOMMEDIUM result overestimates the system multiplication factor (k{sub eff}) by 55 mk, whereas the LATTICECELL and MULTIREGION treatments predict the k{sub eff} values with similar biases of approximately 10 mk overestimation. The DOUBLEHET result shows a more satisfactory agreement, about 4.2 mk underestimation in the k{sub eff} value. In addition, using cell-weighted cross sections instead of an explicit modeling of TRISO particles in fuel region can further reduce the computation time by a factor of 5 without sacrificing accuracy. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Path to a commercial fast reactor option in the United States

Fast reactors represent one technology with the potential to transform the energy sector through increased resource utilization and unique waste management opportunities that are not available through the established light water reactor (LWR) technology. The technology is 'old' by 21 st century standards, as the United States and other nations have funded fast reactor research and development efforts from the birth of nuclear power that have led to deployment at all scales from experimental to commercial. Yet, in spite of great promise, the experience with fast reactors can be characterized as mixed, with both notable successes and failures. Why then, after 50 years of development, is there no commercial fast reactor operating in the United States? Is commercialization of the technology possible? If so, what business case is needed for a commercial utility to operate a fast reactor? This paper will attempt to sketch a possible path for the development and demonstration of technology needed to make fast reactors a real option for commercial operation by mid-century. This path starts with today's proven LWR technology and uranium oxide fuels and takes an evolutionary route to a first commercial fast reactor that complements and supports the existing reliable LWR fleet. This paper is not intended to promote any one technology or approach, but instead seeks to illustrate the value of national level support for an energy technology program oriented toward demonstration and seeks eventual deployment of transformational energy systems on the scale and time-frame that matters. The observations and conclusions presented are derived primarily from the collective experience and expertise of the authors who represent a broad range of commercial perspectives from the utility, vendor, research and development, and regulatory policy communities. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The United States after the great recession: the challenge of sustainable growth

The paper outlines the strengths and weaknesses of the U.S. economic growth model, assesses its’ ability to respond to the key economic, environmental and social challenges currently facing the U.S. and proposes policies that if adopted would move the U.S. onto a more sustainable growth path. The paper provides scenarios of projected future growth trajectories, as well as recommendations for specific policies in key areas: employment, infrastructure, energy and fiscal rebalancing. To reach this goal this paper focuses on four areas for action: Increasing employment, which is the most urgent priority to accelerate recovery from the Great Recession, while addressing underlying structural issues that have led to a decade of poor economic outcomes for most citizens; Investing in the future, as the key marker of whether the United States is prepared to make farsighted decisions to improve education, build new infrastructure and increase innovation; Maximizing an increased energy endowment in a way that grows the economy, while reinforcing the trend towards reducing resource demand and reducing greenhouse gas emissions; and, Fiscal rebalancing, where the United States must insulate economic recovery from the process of fiscal reform while reducing and stabilizing debt over the long term. Finally, we argue that President Obama can re-energize America’s global leadership if he builds on a platform of domestic actions that enhance the sustainability of America’s society and economy.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Grout Long Radius Flow Testing to Support Saltstone Disposal Unit 6 Design - 13352

The Saltstone Facility, located within the Savannah River Site (SRS) near Aiken, South Carolina, consists of two facility segments: The Saltstone Production Facility (SPF) and the Saltstone Disposal Facility (SDF). The SPF receives decontaminated legacy low level sodium salt waste solution that is a byproduct of prior nuclear material processing. The salt solution is mixed with cementitious materials to form a grout slurry known as 'Saltstone'. The grout is pumped to the SDF where it is placed in a Saltstone Disposal Unit (SDU) to solidify. SDU 6 is referred to as a 'mega vault' and is currently in the design stage. The conceptual design for SDU 6 is a single cell, cylindrical geometry approximately 114.3 meters in diameter by 13.1 meter high and is larger than previous cylindrical SDU designs, 45.7 meters in diameter by 7.01 meters high (30 million gallons versus 2.9 million gallons of capacity). Saltstone slurry will be pumped into the new waste disposal unit through roof openings at a projected flow rate of about 34.1 cubic meters per hour. Nine roof openings are included in the design to discharge material into the SDU with an estimated grout pour radius of 22.9 to 24.4 meters and initial drop height of 13.1 meters. The conceptual design for the new SDU does not include partitions to limit the pour radius of the grout slurry during placement other than introducing material from different pour points. This paper addresses two technical issues associated with the larger diameter of SDU 6; Saltstone flow distance in a tank 114.3 meters in diameter and quality of the grout. A long-radius flow test scaled to match the velocity of an advancing grout front was designed to address these technology gaps. The emphasis of the test was to quantify the flow distance and to collect samples to evaluate cured properties including compressive strength, porosity, density, and saturated hydraulic conductivity. Two clean cap surrogate mixes (Saltstone premix plus water) were designed to simulate slurry with the reference Saltstone rheology and a Saltstone with extra water from the process flushing operation. Long-radius flow tests were run using approximately 4.6 cubic meters of each of these mixes. In both tests the pump rate was 0.063 liters/second (1 gpm). A higher pump rate, 0.19 liters/second (3 gpm), was used in a third long-radius flow test. The angle of repose of the grout wedges increased as a function of time in all three tests. The final angles of repose were measured at 3.0 deg., 2.4 deg., and 0.72 deg.. The pump rate had the largest effect on the radial flow distance and slope of the grout surface. The slope on the pour placed at 0.19 liters/second (3 gpm) was most representative of the slope on the grout currently being pumped into SDU 2 which is estimated to be 0.7 deg. to 0.9 deg. The final grout heights at 1/3 of a meter from the discharge point were 115, 105, and 38 cm. Entrapped air (≥ 0.25 cm bubbles) was also observed in all of the mixes. The entrapped air appeared to be released from the flows within about 3.1 meters (10 feet) of the discharge point. The bleed water was clear but had a thin layer of floating particulates. The bleed water should be retrievable by a drain water collection system in SDU 6 assuming the system does not get clogged. Layering was observed and was attributed to intervals when the hopper was being cleaned. Heat from the hydration reactions was noticeable to the touch. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Walk the Line: The Development of Route Selection Standards for Spent Nuclear Fuel and High-level Radioactive Waste in the United States - 13519

Although storage facilities for spent nuclear fuel (SNF) and high-level radioactive waste (HLRW) are widely dispersed throughout the United States, these materials are also relatively concentrated in terms of geographic area. That is, the impacts of storage occur in a very small geographic space. Once shipments begin to a national repository or centralized interim storage facility, the impacts of SNF and HLRW will become more geographically distributed, more publicly visible, and almost certainly more contentious. The selection of shipping routes will likely be a major source of controversy. This paper describes the development of procedures, regulations, and standards for the selection of routes used to ship spent nuclear fuel and high-level radioactive waste in the United States. The paper begins by reviewing the circumstances around the development of HM-164 routing guidelines. The paper discusses the significance of New York City versus the Department of Transportation and application of HM-164. The paper describes the methods used to implement those regulations. The paper will also describe the current HM-164 designated routes and will provide a summary data analysis of their characteristics. This analysis will reveal the relatively small spatial scale of the effects of HM 164. The paper will then describe subsequent developments that have affected route selection for these materials. These developments include the use of 'representative routes' found in the Department of Energy (DOE) 2008 Supplemental Environmental Impact Statement for the formerly proposed Yucca Mountain geologic repository. The paper will describe recommendations related to route selection found in the National Academy of Sciences 2006 report Going the Distance, as well as recommendations found in the 2012 Final Report of the Blue Ribbon Commission on America's Nuclear Future. The paper will examine recently promulgated federal regulations (HM-232) for selection of rail routes for hazardous materials transport. The paper concludes that while the HM 164 regime is sufficient for certain applications, it does not provide an adequate basis for a national plan to ship spent nuclear fuel and high-level radioactive waste to centralized storage and disposal facilities over a period of 30 to 50 years. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Post-Closure Challenges of U.S. Department of Energy Sites in Desert Environments of the Southwestern United States - 12095

U.S. Department of Energy (DOE) sites located in harsh desert environments of the Four Corners region of the southwestern United States require diligence and continual maintenance to ensure the remediation systems function as designed to protect human health and the environment. The geology and climate of this area create issues that are unique to these sites. Geologic formations contain naturally occurring constituents that are often the same as the residual contaminants remaining from historical milling activities at the sites. Although annual precipitation is low, when precipitation events occur they can be of extreme intensity, resulting in erosion and flooding that can quickly destroy infrastructure and rapidly change site conditions. Winds can cause sand storms and sand mounding that effect site features. These challenging environmental conditions, along with the remote locations of the sites, require active management beyond what was originally envisioned for uranium disposal sites to address concerns in a safe and cost-effective manner. The unique environment of the Four Corners region creates many challenges to the LTSM of LM sites in southwestern United States. The remediation efforts and approaches to infrastructure have to be specifically structured to work in this environment. Often, the systems and structures have to be modified based on lessons learned on how to best adapt to these difficult conditions and remote locations. These sites require continual maintenance and additional efforts compared to many other LM sites. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Radioactive Water Treatment at a United States Environmental Protection Agency Superfund Site - 12322

A water treatment system at a United States Environmental Protection Agency (USEPA) Superfund site impacted by radiological contaminants is used to treat water entering the site. The United States Army Corps of Engineers (USACE) is actively managing the remedial action for the USEPA using contracts to support the multiple activities on site. The site is where former gas mantle production facilities operated around the turn of the century. The manufacturing facilities used thorium ores to develop the mantles and disposed of off-specification mantles and ore residuals in the surrounding areas. During Site remedial actions, both groundwater and surface water comes into contact with contaminated soils and must be collected and treated at an on-site treatment facility. The radionuclides thorium and radium with associated progeny are the main concern for treatment. Suspended solids, volatile organic compounds, and select metals are also monitored during water treatment. The water treatment process begins were water is pumped to a collection tank where debris and grit settle out. Stored water is pumped to a coagulant tank containing poly-aluminum chloride to collect dissolved solids. The water passes into a reaction tube where aspirated air is added or reagent added to remove Volatile Organic Compounds (VOC'S) by mass transfer and convert dissolved iron to a solid. The water enters the flocculent polymer tank to drop solids out. The flocculated water overflows to a fluidized bed contact chamber to increase precipitation. Flocculation is where colloids of material drop out of suspension and settle. The settled solids are periodically removed and disposed of as radioactive waste. The water is passed through filters and an ion exchange process to extract the radionuclides. Several million liters of water are processed each year from two water treatment plants servicing different areas of the remediation site. Ion exchange resin and filter material are periodically replaced and disposed of as radioactive waste. A total of 0.85 m{sup 3} of waste sludge per year requires disposal on average, in addition to another 6.6 m{sup 3} of waste cartridge filters. All water discharges are regulated by a state of New Jersey Pollutant Discharge Elimination System Permit implemented by the Federal Water Pollution Control Act (Clean Water Act). Laboratory analyses are required to satisfy requirements of the state NPDES permit. Specific monitoring parameters and discharge rates will be provided. Use of the water treatment systems drastically reduces the amount of contaminated water requiring solidification and water disposal to near zero. Millions of liters of potentially contaminated water from excavation activities is treated and released within permit limits. A small volume of solid radioactive waste (21 cubic meters) is generated annually from water treatment process operations. Management of ground and surface water is effectively controlled in remediation areas by the use of sumps, erosion control measures and pumping of water to storage vessels. Continued excavations can be made as water impacting the site is effectively controlled. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Application of European Large Component Technology in the United States - 12561

The European nuclear community currently has safer, more environmentally-friendly disposal options for large component disposal than the United States. The technology and innovation that makes these options viable will soon be available stateside. The removal and replacement of steam generators is a large and complicated task making volume reduction a vital service for the nuclear power industry. As plants age, the replacement of certain components is required in order to maintain plant efficiency and public safety. Currently in the United States, there are 3 options for the disposal of these items including: on-site storage, direct-disposal at a licensed (low-level radioactive waste) LLWR site, and volume reduction prior to disposal. If today's nuclear plants are to be used by future generations, waste stored on-site will eventually have to be disposed of to make room for newer, more advanced technology. Also, the space at LLWR disposal sites is finite, so all waste sent for disposal should be minimized whenever possible. Reducing the volume of decommissioned steam generators prior to final disposal shows the public that the nuclear industry is doing everything that it can to minimize its waste and conserve the environment. Additionally, many steam generators are massive and are not easily transported to a disposal site. When there is no practical transportation route, the size and weight of the component must be reduced. For various reasons including public safety, cost, and technical expertise, size reduction cannot be practically performed at the site of generation. However, since most facilities have some kind of access to a waterway, the components can be safely transported to another facility with barge access for size reduction. The size reduction process for steam generators has evolved over the past 5 years. Because of reductions to the amount of final waste, the dose to personnel, and the processing time, it is now an environmentally and economically friendly alternative to on-site storage and direct disposal. The major operations of this process include: - removal of the carbon steel steam generator dome; - removal of the channel head and majority of tube sheet to free the tubes from the tube sheet and gain access to all of the tubes for grit blasting; - grit blast decontamination of the steam generator tubes to allow disassembly; - removal of the U-Bend Section of the tubes to allow for tube pulling - tube pulling operations; - disassembly of the remainder of the steam generator shell and tube support assemblies; - size reduction of the steam generator resultant materials. All of the equipment for the American market is based on previous designs but has been adapted to meet the size requirements for processing of larger steam generators. This includes a large horizontal band saw, a tube pulling machine, tube blasting equipment, and a diamond wire saw frame. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Grouse and Land-Based Wind Energy Development in the United States

Several species of grouse occupy prairie and sagebrush habitat across the western United States. Sharp-tailed grouse (Tympanuchus phasianellus), greater prairie chicken (Tympanuchus cupido), and lesser prairie-chicken (Tympanuchus pallidicinctus) reside in the grassland prairies of the Great Plains. In the Intermountain West, greater sage-grouse (Centrocercus urophasianus) and Gunnison sage-grouse (Centrocercus minimus) inhabit the expansive sagebrush plains. The continued deployment of wind energy across the United States, particularly in prairie and sagebrush habitats, may result in a myriad of impacts to grouse species, although there is a high degree of uncertainty regarding the extent of the impact.

avoidance↗

Characterization and Remediation of the Hanford 618-10 Burial Ground Vertical Pipe Units - 17121

The 618-10 Burial Ground is approximately 148 m by 143 m (485 feet by 470 feet) and consists of 12 trenches and 94 Vertical Pipe Units (VPU's). It is located approximately 8.1 km (5 miles) north of Richland, Washington in the 600 Area of the Hanford Site. The 618-10 Burial Ground received low- to high-activity waste (e.g., fission products and some plutonium-contaminated waste). Most of the waste originated at the 300 Area laboratory facilities. Lower activity radioactive material and shielded drums were disposed in trenches, while laboratory wastes with higher levels of radiation were disposed in Vertical Pipe Units (VPUs). There are different variants of VPUs. Some VPUs are simply corrugated culverts or standard pipes, 36 cm (14 in.) diameter and 3.1 m to 4.6 m (10- to 15-ft) long, buried vertically. Some VPUs are carbon steel pipes 25 to 61 cm (10 to 24 in.) in diameter and up to 4.6 m (15 ft) in length. The final design of the VPUs is 56 cm (22-in) diameter, 4.4 m (14.4 ft) long waste receptacles constructed by welding five 208 L (55-gallon) bottomless drums together end-to-end and burying them vertically, separated by approximately 3.1 m (10 feet) on center in rows approximately 7.6 m (25 feet) apart. The 618-10 Burial Ground contains approximately 94 VPUs. Historical documents indicate that shielding materials (e.g., concrete or soil) may have been added to the VPUs to reduce dose rates over the openings, and that each VPU was backfilled with sand and capped with concrete at the end of its service life. Historical documents also indicate that the VPUs were covered with approximately 0.6 m (2-ft) of soil when they were closed, and an additional 0.6 m (2-ft) of topsoil was later added for surface stabilization. In general, the process for VPU remediation was as follows: - Installed four cone penetrometers (CPTs) around the exterior of each individual VPU and sent radiation detection probes down the interior of the CPTs to get initial radiation data in order to calculate the overall curie content and create maps showing the dose rate distribution throughout the VPU. - Removed the CPTs and installed a 122 cm (48-in) diameter, 1.3 cm (0.5-in) thick steel over-casing using a vibrating hammer suspended from a crane that encompassed the VPU with some surrounding soil. - Using a Bauer BG-30 drill rig with a specifically designed augur bit and a specially designed confinement system the auger process was used to stabilize and size reduce the contents. - Once the auger reached a depth of 8.5 m (28 feet) the BG-30 drill stem was separated and additional characterization was completed by sending a radiation probe down the center of the drill stem to gather radiological data. - Once auguring and characterization was completed the waste was removed using a specially designed extended clamshell retrieval bucket and placed into individual 2.7 m x 1.5 m x 1.2 m (9-ft x 5-ft x 4-ft) metal boxes. - After the waste was placed into the metal waste boxes a low strength grout was added and the grout and waste material was mixed using a large rake device attached to an excavator. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗