Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “single layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

The transmission or scattering of elastic waves by an inhomogeneity of simple geometry: A comparison of theories

The extended method of equivalent inclusion developed is applied to study the specific wave problems of the transmission of elastic waves in an infinite medium containing a layer of inhomogeneity, and of the scattering of elastic waves in an infinite medium containing a perfect spherical inhomogeneity. The eigenstrains are expanded as a geometric series and the method of integration for the inhomogeneous Helmholtz operator given by Fu and Mura is adopted. The results obtained by using a limited number of terms in the eigenstrain expansion are compared with exact solutions for the layer problem and for a perfect sphere. Two parameters are singled out for this comparison: the ratio of elastic moduli, and the ratio of the mass densities. General trends for three different situations are shown.

Sheu, Y. C.↗
NASA NTRS1986

Temperature retrievals by Rayleigh backscatter lidar signals

Differences between retrieved temperatures from lidar and atmospheric model temperatures are calculated for four problems: (1) the effect of a transient thin aerosol layer at any altitude on temperature retrieved by a single-wavelength lidar; (2) the effect of residual aerosols on temperature retrieved by a two-wavelength lidar; (3) the errors due to splicing two backscatter signals which are obtained separately; and (4) the effect of multiple scattering. The results show that temperatures can be retrieved for + or - 3 K if Rayleigh backscatter can be measured for + or - 1.5 percent. The LITE lidar in a 240 km orbit aboard the Shuttle should be able to make a + or -3 K measurements from 10-40 km with vertical resolutions of 1 km and horizontal resolutions of 300 km.

Uchino, O.↗
NASA NTRS2005

An Inventory of Impact Craters on the Martian South Polar Layered Deposits

The polar layered deposits (PLD) of Mars continue to be a focus of study due to the possibility that these finely layered, volatile-rich deposits hold a record of recent eras in Martian climate history. Recently, the visible sensor on 2001 Mars Odyssey s Thermal Emission Imaging System (THEMIS) has acquired 36 meter/pixel contiguous single-band visible image data sets of both the north and the south polar layered deposits, during the local spring and summer seasons. In addition, significant coverage has been obtained at the THEMIS visible sensor s full resolution of 18 meters/pixel. This paper reports on the use of these data sets to further characterize the population of impact craters on the south polar layered deposits (SPLD), and the implications of the observed population for the age and evolution of the SPLD.

Plaut, J. J.↗
NASA NTRS1979

Heterojunction semiconductor device

A layer of germanium on a body of P type conductivity single crystal indium phosphide provides a blocking heterojunction. This device will emit light when a suitable voltage is placed thereacross or the device can be used as a photoconductor to generate electrons when light is directed thereon.

Harwylo, Frank Z.↗
NASA NTRS2012

Shape and Color Features for Object Recognition Search

A bio-inspired shape feature of an object of interest emulates the integration of the saccadic eye movement and horizontal layer in vertebrate retina for object recognition search where a single object can be used one at a time. The optimal computational model for shape-extraction-based principal component analysis (PCA) was also developed to reduce processing time and enable the real-time adaptive system capability. A color feature of the object is employed as color segmentation to empower the shape feature recognition to solve the object recognition in the heterogeneous environment where a single technique - shape or color - may expose its difficulties. To enable the effective system, an adaptive architecture and autonomous mechanism were developed to recognize and adapt the shape and color feature of the moving object. The bio-inspired object recognition based on bio-inspired shape and color can be effective to recognize a person of interest in the heterogeneous environment where the single technique exposed its difficulties to perform effective recognition. Moreover, this work also demonstrates the mechanism and architecture of the autonomous adaptive system to enable the realistic system for the practical use in the future.

Duong, Tuan A.↗
DOE OSTI2026

MnRhBi3: A Cleavable Antiferromagnetic Metal

This dataset contains DFT input and output files supporting the theoretical modeling in the associated publication (Chem. Mater. 2024, 36, 11306-11316). The calculations characterize MnRhBi3, an orthorhombic (Cmmm) van der Waals-layered intermetallic compound that cleaves easily between neighboring Bi layers. The dataset is organized into three calculation types: (i) Bulk: Structural relaxations of the periodic MnRhBi3 crystal in antiferromagnetic (AFM) and ferromagnetic (FM) configurations, using the vdW-DF-optB86b functional. These provide the equilibrium lattice constants, magnetic energy differences (AFM is 0.5 meV/f.u. lower than FM), and magnetic moments (4.4 µB/Mn, 0.17 µB/Rh, 0.18 µB/Bi) reported in Table 1 of the main text. (ii) Slab: Same magnetic configurations computed with an 18 Ang vacuum layer introduced between Bi layers, used to calculate the cleavage energy Ec = 0.56 J/m2 (AFM) and 0.57 J/m2 (FM), establishing MnRhBi3 as a van der Waals-layered material comparable to graphite, MoS2, and CrI3. (iii) ELF: Single-point calculation on the relaxed bulk AFM geometry with LELF=.TRUE., producing the ELFCAR file used to generate electron localization function isosurfaces and contour maps (Fig. 2, main text) showing Bi lone pairs directed into the van der Waals gaps. All folders contain CONTCAR, INCAR, KPOINTS, OUTCAR, and POSCAR. The ELF/ folder additionally contains ELFCAR. Calculations were performed using VASP 6.3.2 with PBE + vdW-DF-optB86b, PAW potentials, and an energy cutoff of 800 eV.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Optical image analysis for graphene layer detection: Enhanced green channel methodology

Graphene, a material of increasing research interest, requires accurate layer identification due to its sensitivity to layer count. Existing methods for graphene layer number identification are either time-consuming or of low accuracy, with high-accuracy methods often requiring expensive processes. This paper aims to address this challenge by proposing a cost-effective and efficient approach. Specifically, the current work highlights only the green channel—one of the three primary color channels (red, green, blue) that make up an optical image—from images of exfoliated graphene flakes for layer count identification. A linear regression is performed between pixel position and substrate green channel value, and this effect is subtracted from the entire optical image to mitigate background effects. By storing the range of green channel values for each type of flake (monolayer, bilayer, or tri-layer) based on a few images, we establish thresholds for identifying different types of layers in a particular setup. Additionally, our methodology allows for flexible threshold tuning using a single reference image, enabling adjustment to changes in detection setup such as illumination level, magnification, or microscope used. Finally, demonstrating high accuracy and flexibility, this methodology presents a suitable technique for graphene layer number identification without the need for large datasets or expensive instruments.

2D materials↗
DOE OSTI2024

One-Pot Self-Assembly of Sequence-Controlled Mesoporous Heterostructures via Structure-Directing Agents

Multimaterial heterostructures have led to characteristics surpassing the individual components. Nature controls the architecture and placement of multiple materials through biomineralization of nanoparticles (NPs); however, synthetic heterostructure formation remains limited and generally departs from the elegance of self-assembly. Here, in this study, a class of block polymer structure-directing agents (SDAs) are developed containing repeat units capable of persistent (covalent) NP interactions that enable the direct fabrication of nanoscale porous heterostructures, where a single material is localized at the pore surface as a continuous layer. This SDA binding motif (design rule 1) enables sequence-controlled heterostructures, where the composition profile and interfaces correspond to the synthetic addition order. This approach is generalized with 5 material sequences using an SDA with only persistent SDA-NP interactions (“P-NP 1 –NP 2 ”; NP i = TiO 2 , Nb 2 O 5 , ZrO 2 ). Expanding these polymer SDA design guidelines, it is shown that the combination of both persistent and dynamic (noncovalent) SDA-NP interactions (“PD-NP 1 –NP 2 ”) improves the production of uniform interconnected porosity (design rule 2). The resulting competitive binding between two segments of the SDA (P- vs D-) requires additional time for the first NP type (NP 1 ) to reach and covalently attach to the SDA (design rule 3). The combination of these three design rules enables the direct self-assembly of heterostructures that localize a single material at the pore surface while preserving continuous porosity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1990

Critical-layer nonlinearity in the resonance growth of three-dimensional waves in boundary layers

The nonlinear interactions of a triad of initially linear stability waves are addressed. The triad consisted of a single two-dimensional mode at a given frequency and two oblique modes with equal and opposite spanwise wave numbers. The oblique waves were at half the frequency and streamwise wave number of the two-dimensional mode. Attention was focused on the boundary-layer transition at low frequencies and high Reynolds numbers. A five-zoned structure and low-frequency scaling were used to derive the nonlinear-interaction equations. The initial nonlinear development of the waves was analyzed; the results indicated that the two-dimensional wave behaves according to linear theory. Nonlinear interactions caused exponential-of-an-exponential growth of the oblique modes. This resonant amplification of the subharmonic depended on the initial amplitude of the two-dimensional wave and on the initial phase angle between the two-dimensional wave and the oblique waves. The resonant growth of the oblique modes was more pronounced at lower frequencies than at higher frequencies. The results are in good agreement with experimental results and offer explanations of the observed process.

Mankbadi, Reda R.↗
NASA NTRS1994

Parabolized stability equations

The parabolized stability equations (PSE) are a new approach to analyze the streamwise evolution of single or interacting Fourier modes in weakly nonparallel flows such as boundary layers. The concept rests on the decomposition of every mode into a slowly varying amplitude function and a wave function with slowly varying wave number. The neglect of the small second derivatives of the slowly varying functions with respect to the streamwise variable leads to an initial boundary-value problem that can be solved by numerical marching procedures. The PSE approach is valid in convectively unstable flows. The equations for a single mode are closely related to those of the traditional eigenvalue problems for linear stability analysis. However, the PSE approach does not exploit the homogeneity of the problem and, therefore, can be utilized to analyze forced modes and the nonlinear growth and interaction of an initial disturbance field. In contrast to the traditional patching of local solutions, the PSE provide the spatial evolution of modes with proper account for their history. The PSE approach allows studies of secondary instabilities without the constraints of the Floquet analysis and reproduces the established experimental, theoretical, and computational benchmark results on transition up to the breakdown stage. The method matches or exceeds the demonstrated capabilities of current spatial Navier-Stokes solvers at a small fraction of their computational cost. Recent applications include studies on localized or distributed receptivity and prediction of transition in model environments for realistic engineering problems. This report describes the basis, intricacies, and some applications of the PSE methodology.

Herbert, Thorwald↗
DOE OSTI2021

Mono- and bilayer smectic liquid crystal ordering in dense solutions of “gapped” DNA duplexes

Significance Liquid crystalline behavior of DNA has been studied for decades, yet only recently has one of the most fundamental liquid crystal phases—the smectic phase in which rod-like objects assemble into stacks of fluid layers—been demonstrated in this system. Here, we describe distinct bilayer and monolayer smectic phases in solutions of “gapped” DNA (GDNA), consisting of two DNA duplexes connected by a single strand. The smectic order is amphotropic (sensitive to temperature as well as concentration), and the layer structure is stable against significant perturbations of the GDNA construct (e.g., “gap” length variation and asymmetry in duplex lengths). The temperature sensitivity may provide a means to compare end-to-end interaction strengths between DNA duplexes at biologically relevant concentrations.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Numerical methods for hypersonic boundary layer stability

Four different schemes for solving compressible boundary layer stability equations are developed and compared, considering both the temporal and spatial stability for a global eigenvalue spectrum and a local eigenvalue search. The discretizations considered encompass: (1) a second-order-staggered finite-difference scheme; (2) a fourth-order accurate, two-point compact scheme; (3) a single-domain Chebychev spectral collocation scheme; and (4) a multidomain spectral collocation scheme. As Mach number increases, the performance of the single-domain collocation scheme deteriorates due to the outward movement of the critical layer; a multidomain spectral method is accordingly designed to furnish superior resolution of the critical layer.

Malik, M. R.↗
DOE OSTI2025

A structural analysis of ordered Cs3Sb films grown on single crystal graphene and silicon carbide substrates

Alkali antimonides are well established as high efficiency, low intrinsic emittance photocathodes for accelerators and photon detectors. However, conventionally grown alkali antimonide films are polycrystalline with surface disorder and roughness that can limit achievable beam brightness. Ordering the crystalline structure of alkali antimonides has the potential to deliver higher brightness electron beams by reducing surface disorder and enabling the engineering of material properties at the level of atomic layers. In this report, we demonstrate the growth of ordered Cs3Sb films on single crystal substrates 3C-SiC and graphene-coated 4H-SiC using pulsed laser deposition and conventional thermal evaporation growth techniques. The crystalline structures of the Cs3Sb films were examined using reflection high energy electron diffraction and x-ray diffraction diagnostics, while film thickness and roughness estimates were made using x-ray reflectivity. With these tools, we observed ordered domains in less than 10 nm thick films with quantum efficiencies greater than 1% at 530 nm. Moreover, we identify structural features such as Laue oscillations indicative of highly ordered films. We found that Cs3Sb films grew with flat, fiber-textured surfaces on 3C-SiC and with multiple ordered domains and sub-nanometer surface roughness on graphene-coated 4H-SiC under our growth conditions. We identify the crystallographic orientations of Cs3Sb grown on graphene-coated 4H-SiC substrates and discuss the significance of examining the crystal structure of these films for growing epitaxial heterostructures in future experiments.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Entrainment-Zone Restratification and Flow Structures in Stratified Shear Turbulence

Late-time dynamics and morphology of a stratified turbulent shear layer are examined using 1) Reynolds-stress and heat-flux budgets, 2) the single-point structure tensors introduced by Kassinos et al. (2001), and 3) flow visualization via 3D volume rendering. Flux reversal is observed during restratification in the edges of the turbulent layer. We present a first attempt to quantify the turbulence-mean-flow interaction and to characterize the predominant flow structures. Future work will extend this analysis to earlier times and different values of the Reynolds and Richardson numbers.

Reif, B. Anders Pettersson↗
NASA NTRS2001

A Radiation-Tolerant, Low-Power Non-Volatile Memory Based on Silicon Nanocrystal Quantum Dots

Nanocrystal nonvolatile floating-gate memories are a good candidate for space applications - initial results suggest they are fast, more reliable and consume less power than conventional floating gate memories. In the nanocrystal based NVM device, charge is not stored on a continuous polysilicon layer (so-called floating gate), but instead on a layer of discrete nanocrystals. Charge injection and storage in dense arrays of silicon nanocrystals in SiO2 is a critical aspect of the performance of potential nanocrystal flash memory structures. The ultimate goal for this class of devices is few- or single-electron storage in a small number of nanocrystal elements. In addition, the nanocrystal layer fabrication technique should be simple, 8-inch wafer compatible and well controlled in program/erase threshold voltage swing was seen during 100,000 program and erase cycles. Additional near-term goals for this project include extensive testing for radiation hardness and the development of artificial layered tunnel barrier heterostructures which have the potential for large speed enhancements for read/write of nanocrystal memory elements, compared with conventional flash devices. Additional information is contained in the original extended abstract.

Bell, L. D.↗
NASA NTRS2001

A radiation - tolerant, low - power non - volatile memory based on silicon nanocrystal quantum dots.

Nanocrystal nonvolatile floating-gate memories are a good candidate for space applications - initial results suggest they are fast, more reliable and consume less power than conventional floating gate memories. In the nanocrystal based NVM device, charge is not stored on a continuous polysilicon layer (so-called floating gate), but instead on a layer of discrete nanocrystals. Charge injection and storage in dense arrays of silicon nanocrystals in Si02 is a critical aspect of the performance of potential nanocrystal flash memory structures. The ultimate goal for this class of devices is few- or single-electron storage in a small number of nanocrystal elements. In addition, the nanocrystal layer fabrication technique should be simple, 8-inch wafer compatible and well controlled.

Green, M. L.↗