Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sensor data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Earth surface sensing in the '90's

Advances in Earth sensor technology and data handling techniques are reviewed. These will allow the acquisition of high resolution images over a wide range of the electromagnetic spectrum (from microwave to optical) with sufficient spectral resolution to permit detailed analysis of the surface chemical, thermal, and physical properties. When combined with the topography, this will allow the user to analyze the full data set in a perspective view that enhances interpretation capability.

Elachi, Charles↗

Hot ions observed by the Giotto ion mass spectrometer inside the Comet Halley contact surface

Just inside the contact surface (approx. 4700 km) the High Energy Range Spectrometer (HERS) sensor of the Giotto ion mass spectrometer detected a sudden, intense burst of ions that lasted until the HERS sensor ceased transmitting data at a distance 3000 km from comet Halley. During this interval ions with M/Q=1, 2, 12, 14, 16, 19, 24 and 28 were observed. The heavier ions appear in two populations (in the S/C frame): a very low energy, almost omnidirectional distribution, and a more energetic (approx. < ram speed) population coming from the ram direction. The low energy ions may belong to the natural Halley environment or be generated at the spacecraft by dust and gas bombardment. The ions may also be related to spacecraft charging processes on Giotto.

Goldstein, R.↗

Spacecraft on-board SAR processing technology

This paper provides an assessment of the on-board SAR processing technology for Eos-type missions. The proposed Eos SAR sensor and flight data system are introduced, and the SAR processing requirements are described. The SAR on-board SAR processor architecture selection is discussed, and a baseline processor architecture using a frequency-domain processor for range correlation and a modular fault-tolerant VLSI time-domain parallel array for azimuth correlation are described. The mass storage and VLSI technologies needed for implementing the proposed SAR processing are assessed. It is shown that acceptable processor power and mass characteristics should be feasible for Eos-type applications. A proposed development strategy for the on-board SAR processor is presented.

Liu, K. Y.↗

Ada and knowledge-based systems: A prototype combining the best of both worlds

A software architecture is described which facilitates the construction of distributed expert systems using Ada and selected knowledge based systems. This architecture was utilized in the development of a Knowledge-based Maintenance Expert System (KNOMES) prototype for the Space Station Mobile Service Center (MSC). The KNOMES prototype monitors a simulated data stream from MSC sensors and built-in test equipment. It detects anomalies in the data and performs diagnosis to determine the cause. The software architecture which supports the KNOMES prototype allows for the monitoring and diagnosis tasks to be performed concurrently. The basic concept of this software architecture is named ACTOR (Ada Cognitive Task ORganization Scheme). An individual ACTOR is a modular software unit which contains both standard data processing and artificial intelligence components. A generic ACTOR module contains Ada packages for communicating with other ACTORs and accessing various data sources. The knowledge based component of an ACTOR determines the role it will play in a system. In this prototype, an ACTOR will monitor the MSC data stream.

Brauer, David C.↗

Dynamic perspective displays and the control of tilt-rotor aircraft in simulated flight

Two simulations were conducted to study the effect of dynamic perspective displays on performance measures collected during simulated flight. The first study was a pure altitude regulation task with simple first order plant dynamics. In the second simulation, pilots performed two basic rotary-wing flight tasks with dynamic perspective displays projected out-the-window (panoramic head up display) or on a panel mounted simulation of a sensor display. The data from the two studies, taken together, show that when such displays are used during flight, they will not degrade performance; and, under certain display configurations, they will minimize flight control errors.

Bennett, C. T.↗

Independent Orbiter Assessment (IOA): Analysis of the guidance, navigation, and control subsystem

The results of the Independent Orbiter Assessment (IOA) of the Failure Modes and Effects Analysis (FMEA) and Critical Items List (CIL) is presented. The IOA approach features a top-down analysis of the hardware to determine failure modes, criticality, and potential critical items. To preserve independence, this analysis was accomplished without reliance upon the results contained within the NASA FMEA/CIL documentation. The independent analysis results corresponding to the Orbiter Guidance, Navigation, and Control (GNC) Subsystem hardware are documented. The function of the GNC hardware is to respond to guidance, navigation, and control software commands to effect vehicle control and to provide sensor and controller data to GNC software. Some of the GNC hardware for which failure modes analysis was performed includes: hand controllers; Rudder Pedal Transducer Assembly (RPTA); Speed Brake Thrust Controller (SBTC); Inertial Measurement Unit (IMU); Star Tracker (ST); Crew Optical Alignment Site (COAS); Air Data Transducer Assembly (ADTA); Rate Gyro Assemblies; Accelerometer Assembly (AA); Aerosurface Servo Amplifier (ASA); and Ascent Thrust Vector Control (ATVC). The IOA analysis process utilized available GNC hardware drawings, workbooks, specifications, schematics, and systems briefs for defining hardware assemblies, components, and circuits. Each hardware item was evaluated and analyzed for possible failure modes and effects. Criticality was assigned based upon the severity of the effect for each failure mode.

Trahan, W. H.↗

Cockpit display of hazardous wind shear information

Information on cockpit display of wind shear information is given in viewgraph form. Based on the current status of windshear sensors and candidate data dissemination systems, the near-term capabilities for windshear avoidance will most likely include: (1) Ground-based detection: TDWR (Terminal Doppler Weather Radar), LLWAS (Low-Level Windshear Alert System), Automated PIREPS; (2) Ground-Air datalinks: Air traffic control voice channels, Mode-S digital datalink, ACARS alphanumeric datalink. The possible datapaths for integration of these systems are illustrated in a diagram. In the future, airborne windshear detection systems such as lidars, passive IR detectors, or airborne Doppler radars may also become available. Possible future datalinks include satellite downlink and specialized en route weather channels.

Wanke, Craig↗

The procedure safety system

Telerobotic operations, whether under autonomous or teleoperated control, require a much more sophisticated safety system than that needed for most industrial applications. Industrial robots generally perform very repetitive tasks in a controlled, static environment. The safety system in that case can be as simple as shutting down the robot if a human enters the work area, or even simply building a cage around the work space. Telerobotic operations, however, will take place in a dynamic, sometimes unpredictable environment, and will involve complicated and perhaps unrehearsed manipulations. This creates a much greater potential for damage to the robot or objects in its vicinity. The Procedural Safety System (PSS) collects data from external sensors and the robot, then processes it through an expert system shell to determine whether an unsafe condition or potential unsafe condition exists. Unsafe conditions could include exceeding velocity, acceleration, torque, or joint limits, imminent collision, exceeding temperature limits, and robot or sensor component failure. If a threat to safety exists, the operator is warned. If the threat is serious enough, the robot is halted. The PSS, therefore, uses expert system technology to enhance safety thus reducing operator work load, allowing him/her to focus on performing the task at hand without the distraction of worrying about violating safety criteria.

Obrien, Maureen E.↗

A numerical algorithm to propagate navigation error covariance matrices associated with generalized strapdown inertial measurement units

The design and operation of a Strapdown Navigation Analysis Program (SNAP) developed to perform covariance analysis on spacecraft inertial-measurement-unit (IMU) navigation errors are described and demonstrated. Consideration is given to the IMU modeling subroutine (with user-specified sensor characteristics), the data input procedures, state updates and the simulation of instrument failures, the determination of the nominal trajectory, the mapping-matrix and Monte Carlo covariance-matrix propagation methods, and aided-navigation simulation. Numerical results are presented in tables for sample applications involving (1) the Galileo/IUS spacecraft from its deployment from the Space Shuttle to a point 10 to the 8th ft from the center of the earth and (2) the TDRS-C/IUS spacecraft from Space Shuttle liftoff to a point about 2 h before IUS deployment. SNAP is shown to give reliable results for both cases, with good general agreement between the mapping-matrix and Monte Carlo predictions.

Weir, Kent A.↗

Ames Research Center C-130

The C130 Earth Resources Aircraft provides a platform for a variety of sensors that collect data in support of terrestrial and atmospheric projects sponsored by NASA in coordination with Federal, state, university, and industry investigators. This data is applied to research in the areas of forestry, agriculture, land use and land cover analysis, hydrology, geology, photogrammetry, oceanography, meteorology, and other earth science disciplines. The C130 is a platform aircraft flying up to 25,000 feet above sea level at speeds between 150 and 330 knots True Air Speed. The aircraft is capable of precise flight line navigation by means of an optical borescope from which line guidance is provided to the pilots.

Koozer, Mark A.↗

C-130 Automated Digital Data System (CADDS)

Real time airborne data acquisition, archiving and distribution on the NASA/Ames Research Center (ARC) C-130 has been improved over the past three years due to the implementation of the C-130 Automated Digital Data System (CADDS). CADDS is a real time, multitasking, multiprocessing ROM-based system. CADDS acquires data from both avionics and environmental sensors inflight for all C-130 data lines. The system also displays the data on video monitors throughout the aircraft.

Scofield, C. P.↗

The role of the Remotely Augmented Vehicle (RAV) laboratory in flight research

An overview is presented of the unique capabilities and historical significance of the Remotely Augmented Vehicle (RAV) Lab at NASA-Dryden. The role is reviewed of the RAV Lab in enhancing flight test programs and efficient testing of new aircraft control laws. The history of the RAV Lab is discussed with a sample of its application using the X-29 aircraft. The RAV Lab allows for closed or open loop augmentation of the research aircraft while in flight using ground based, high performance real time computers. Telemetry systems transfer sensor and control data between the ground and the aircraft. The RAV capability provides for enhanced computational power, improved flight data quality, and alternate methods for the testing of control system concepts. The Lab is easily reconfigured to reflect changes within a flight program and can be adapted to new flight programs.

Cohen, Dorothea↗

Sea ice concentrations in the Canada Basin during 1988 - Comparisons with other years and evidence of multiple forcing mechanisms

Results from a study of special sensor microwave imager data and visible band DMSP-OLS imagery show a large area of reduced ice concentration in the Canada Basin during summer 1988. Drifting buoys, surface pressure fields, output from the Polar Ice Prediction System sea ice model, and other meteorological data used to examine processes responsible for development of the reduced ice concentrations are discussed. It is noted that, while ice divergence in the summer offers a partial explanation, the model indicates that there are other factors which play contributing roles. Among these factors are the anomalously warm atmospheric conditions, generally clear skies in June and July, extensive fracturing of the pack ice in spring and anomalous advection of oceanic heat. It is found that the second and third of these effects may occur in most years. It is concluded that, although the extent and magnitude of the concentration reductions during 1988 are unusual, these recurring factors tend to predispose the pack ice in the Canada Basin to decay.

Serreze, Mark C.↗

Monitoring the health of control system components

One characteristic of intelligent behavior is recognition of impaired capability. So an intelligent system should be able to monitor its own performance and determine when one of its components has failed - causing it to lose some degree of capability. This is especially important in autonomous operation which is one of the primary motivations for intelligent systems. This paper briefly reviews the principal approaches that have been suggested for monitoring control systems for failures of its sensors and actuators. The important characteristics of these methods are noted and two are selected for further consideration. These two methods, the failure detection filter and generalized parity relations, are described. Results of experiments are then given of detection and isolation of sensor failures using data taken on the Mini-Mast facility at the NASA Langley Research Center. The effects of certain design options are illustrated. The paper concludes with some observations about the general problem of monitoring the health of control systems.

Vander Velde, W. E.↗

Scientific grade CCDs from EG & G Reticon

The design and performance of three scientific grade CCDs are summarized: a 1200 x 400 astronomical array of 27 x 27 sq micron pixels, a 512 x 512 scientific array of 27 x 27 sq micron pixels and a 404 x 64 VNIR array of 52 x 52 sq micron pixels. Each of the arrays is fabricated using a four phase, double poly, buried n-channel, multi-pinned phase CCD process. Performance data for each sensor is presented.

Cizdziel, Philip J.↗

The role of the remotely augmented vehicle (RAV) laboratory in flight research

This paper presents on overview of the unique capabilities and historical significance of the Remotely Augmented Vehicle (RAV) Laboratory at the NASA Dryden Flight Research Facility. The report reviews the role of the RAV Laboratory in enhancing flight test programs and efficient testing of new aircraft control laws. The history of the RAV Laboratory is discussed with a sample of its application using the X-29 aircraft. The RAV Laboratory allows for closed- or open-loop augmentation of the research aircraft while in flight using ground-based, high performance real-time computers. Telemetry systems transfer sensor and control data between the ground and the aircraft. The RAV capability provides for enhanced computational power, improved flight data quality, and alternate methods for the testing of control system concepts. The Laboratory is easily reconfigured to reflect changes within a flight program and can be adapted to new flight programs.

Cohen, Dorothea↗

Mission and sampling analyses for atmospheric satellite experiments

Orbital analyses, instrument-viewing geometry studies, and sampling simulations are performed to define mission concepts for advanced atmospheric research satellite experiments. These analyses are conducted in collaboration with NASA Headquarters and working groups consisting of atmospheric scientists and experiment developers. Analytical techniques are developed and used to optimize geographical coverage, sensor-viewing geometries, data gathering strategies, sampling schemes, orbital characteristics, satellite launch times, and operational modes of the various experiments and mission concepts. Short-term (7 day) Shuttle Missions, the Upper Atmosphere Research Satellite (UARS), and multisatellite missions such as the Earth Observing System (EOS) are being studied. Atmospheric experiments which are being analyzed include nadir-viewing sounders, limb-emission scanners, laser systems, and solar-occultation techniques.

Harrison, Edwin F.↗

Global analyses of water vapor, cloud and precipitation derived from a diagnostic assimilation of SSM/I geophysical retrievals

An analytical approach is described for diagnostically assimilating moisture data from Special Sensor Microwave Imager (SSM/I) into a global analysis of water vapor, cloud content, and precipitation. In this method, 3D fields of wind and temperature values taken from ECMWF gridded analysis are used to drive moisture conservation equations with parameterized microphysical treatment of vapor, liquid, and ice; the evolving field of water vapor is periodically updated or constrained by SSM/I retrievals of precipitable water. Initial results indicate that this diagnostic model can produce realistic large-scale fields of cloud and precipitation. The resulting water vapor analyses agree well with SSM/I and have an additional advantage of being synoptic.

Robertson, Franklin R.↗