Results for “response surface” — Page 93

NASA NTRS2009

Compact Reconnaissance Imaging Spectrometer Observations of Water Vapor and Carbon Monoxide

The Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) onboard the Mars Reconnaissance Orbiter (MRO) spacecraft began taking observations in September 2006 and has now collected more than a full Martian year of data. Retrievals performed using the near-infrared spectra obtained by CRISM are used to characterize the seasonal and spatial variation of the column abundance of water vapor and the column-averaged mixing ratio of carbon monoxide. CRISM retrievals show nominal behavior in water vapor during northern hemisphere spring and summer with maximum abundance reaching 50 precipitable micrometers. Water vapor abundance during the southern hemisphere spring and summer appears significantly reduced compared to observations by other instruments taken during previous years. The CRISM retrievals show the seasonally and globally averaged carbon monoxide mixing ratio to be 700 ppm, but with strong seasonal variations at high latitudes. The summertime near-polar carbon monoxide mixing ratio falls to 200 ppm in the south and 400 ppm in the north as carbon dioxide sublimates from the seasonal polar ice caps and dilutes noncondensable species including carbon monoxide. At low latitudes, the carbon monoxide mixing ratio varies in response to the mean seasonal cycle of surface pressure.

Smith, Michael D.↗

NASA NTRS2012

Real-Time Frequency Response Estimation Using Joined-Wing SensorCraft Aeroelastic Wind-Tunnel Data

A new method is presented for estimating frequency responses and their uncertainties from wind-tunnel data in real time. The method uses orthogonal phase-optimized multi- sine excitation inputs and a recursive Fourier transform with a least-squares estimator. The method was first demonstrated with an F-16 nonlinear flight simulation and results showed that accurate short period frequency responses were obtained within 10 seconds. The method was then applied to wind-tunnel data from a previous aeroelastic test of the Joined- Wing SensorCraft. Frequency responses describing bending strains from simultaneous control surface excitations were estimated in a time-efficient manner.

Grauer, Jared A↗

NASA NTRS2012

Creation of an Upper Stage Trajectory Capability Boundary to Enable Booster System Trade Space Exploration

The problem of trajectory optimization is important in all space missions. The solution of this problem enables one to specify the optimum thrust steering program which should be followed to achieve a specified mission objective, simultaneously satisfying the constraints.1 It is well known that whether or not the ascent trajectory is optimal can have a significant impact on propellant usage for a given payload, or on payload weight for the same gross vehicle weight.2 Consequently, ascent guidance commands are usually optimized in some fashion. Multi-stage vehicles add complexity to this analysis process as changes in vehicle properties in one stage propagate to the other stages through gear ratios and changes in the optimal trajectory. These effects can cause an increase in analysis time as more variables are added and convergence of the optimizer to system closure requires more analysis iterations. In this paper, an approach to simplifying this multi-stage problem through the creation of an upper stage capability boundary is presented. This work was completed as part of a larger study focused on trade space exploration for the advanced booster system that will eventually form a part of NASA s new Space Launch System.3 The approach developed leverages Design of Experiments and Surrogate Modeling4 techniques to create a predictive model of the SLS upper stage performance. The design of the SLS core stages is considered fixed for the purposes of this study, which results in trajectory parameters such as staging conditions being the only variables relevant to the upper stage. Through the creation of a surrogate model, which takes staging conditions as inputs and predicts the payload mass delivered by the SLS upper stage to a reference orbit as the response, it is possible to identify a "surface" of staging conditions which all satisfy the SLS requirement of placing 130 metric tons into low-Earth orbit (LEO).3 This identified surface represents the 130 metric ton capability boundary for the upper stage, such that if the combined first stage and boosters can achieve any one staging point on that surface, then the design is identified as feasible. With the surrogate model created, design and analysis of advanced booster concepts is streamlined, as optimization of the upper stage trajectory is no longer required in every design loop.

Walsh, Ptrick↗

NASA NTRS2013

Spatial and Temporal Dust Source Variability in Northern China Identified Using Advanced Remote Sensing Analysis

The aim of this research is to provide a detailed characterization of spatial patterns and temporal trends in the regional and local dust source areas within the desert of the Alashan Prefecture (Inner Mongolia, China). This problem was approached through multi-scale remote sensing analysis of vegetation changes. The primary requirements for this regional analysis are high spatial and spectral resolution data, accurate spectral calibration and good temporal resolution with a suitable temporal baseline. Landsat analysis and field validation along with the low spatial resolution classifications from MODIS and AVHRR are combined to provide a reliable characterization of the different potential dust-producing sources. The representation of intra-annual and inter-annual Normalized Difference Vegetation Index (NDVI) trend to assess land cover discrimination for mapping potential dust source using MODIS and AVHRR at larger scale is enhanced by Landsat Spectral Mixing Analysis (SMA). The combined methodology is to determine the extent to which Landsat can distinguish important soils types in order to better understand how soil reflectance behaves at seasonal and inter-annual timescales. As a final result mapping soil surface properties using SMA is representative of responses of different land and soil cover previously identified by NDVI trend. The results could be used in dust emission models even if they are not reflecting aggregate formation, soil stability or particle coatings showing to be critical for accurately represent dust source over different regional and local emitting areas.

spectral mixing analysis↗

NASA NTRS2015

The Influence of Sea Ice on Arctic Low Cloud Properties and Radiative Effects

The Arctic is one of the most climatically sensitive regions of the Earth. Climate models robustly project the Arctic to warm 2-3 times faster than the global mean surface temperature, termed polar warming amplification (PWA), but also display the widest range of surface temperature projections in this region. The response of the Arctic to increased CO2 modulates the response in tropical and extra-tropical regions through teleconnections in the atmospheric circulation. An increased frequency of extreme precipitation events in the northern mid-latitudes, for example, has been linked to the change in the background equator-to-pole temperature gradient implied by PWA. Understanding the Arctic climate system is therefore important for predicting global climate change. The ice albedo feedback is the primary mechanism driving PWA, however cloud and dynamical feedbacks significantly contribute. These feedback mechanisms, however, do not operate independently. How do clouds respond to variations in sea ice? This critical question is addressed by combining sea ice, cloud, and radiation observations from satellites, including CERES, CloudSAT, CALIPSO, MODIS, and microwave radiometers, to investigate sea ice-cloud interactions at the interannual timescale in the Arctic. Cloud characteristics are strongly tied to the atmospheric dynamic and thermodynamic state. Therefore, the sensitivity of Arctic cloud characteristics, vertical distribution and optical properties, to sea ice anomalies is computed within atmospheric dynamic and thermodynamic regimes. Results indicate that the cloud response to changes in sea ice concentration differs significantly between atmospheric state regimes. This suggests that (1) the atmospheric dynamic and thermodynamic characteristics and (2) the characteristics of the marginal ice zone are important for determining the seasonal forcing by cloud on sea ice variability.

Taylor, Patrick C.↗

NASA NTRS2017

FOREWORD: Satellite Remote Sensing Beyond 2015

Satellite remote sensing has progressed tremendously since the first Landsat was launched on June 23, 1972. Since the 1970s, satellite remote sensing and associated airborne and in situ measurements have resulted in vital and indispensable observations for understanding our planet through time. These observations have also led to dramatic improvements in numerical simulation models of the coupled atmosphere-land-ocean systems at increasing accuracies and predictive capability. The same observations document the Earth's climate and are driving the consensus that Homo sapiens is changing our climate through greenhouse gas emissions. These accomplishments are the combined work of many scientists from many countries and a dedicated cadre of engineers who build the instruments and satellites that collect Earth observation data from satellites, all working toward the goal of improving our understanding of the Earth. This edition of the Remote Sensing Handbook (Vol. I, II, and III) is a compendium of information for many research areas of our Planet that have contributed to our substantial progress since the 1970s. Remote sensing community is now using multiple sources of satellite and in situ data to advance our studies, what ever they might be. In the following paragraphs, I will illustrate how valuable and pivotal role satellite remote sensing has played in climate system study over last five decades, The Chapters in the Remote Sensing Handbook (Vol. I, II, and III) provides many other specific studies on land, water, and other applications using EO data of last five decades, The Landsat system of Earth-observing satellites has led the way in pioneering sustained observations of our planet. From 1972 to the present, at least one and sometimes two Landsat satellites have been in operation. Starting with the launch of the first NOAA-NASA Polar Orbiting Environmental Satellites NOAA-6 in 1978, improved imaging of land, clouds, and oceans and atmospheric soundings of temperature were accomplished. The NOAA system of polar-orbiting meteorological satellites has continued uninterrupted since that time, providing vital observations for numerical weather prediction. These same satellites are also responsible for the remarkable records of sea surface temperature and land vegetation index from the Advanced Very High Resolution Radiometers (AVHRR) that now span more than 33 years, although no one anticipated these valuable climate records from this instrument before the launch of NOAA-7 in 1981. The success of data from the AVHRR led to the design of the MODIS instruments on NASA's Earth Observing System of satellite platforms that improved substantially upon the AVHRR. The first of the EOS platforms, Terra, was launched in 2000 and the second of these platforms, Aqua, was launched in 2002.

Tucker, Compton J.↗

NASA NTRS2017

The Climatology of Carbon Monoxide and Water Vapor on Mars as Observed by CRISM and Modeled by the GEM-Mars General Circulation Model

Radiative transfer modeling of near-infrared spectra taken by the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) instrument onboard Mars Reconnaissance Orbiter (MRO) enables the column-integrated abundance of carbon monoxide (CO) and water vapor (H 2 O) to be retrieved. These results provide a detailed global description of the seasonal and spatial distribution of CO in the Mars atmosphere and new information about the interannual variability of H2O. The CRISM retrievals show the seasonally and globally averaged carbon monoxide mixing ratio to be near 800 parts per million, but with strong seasonal variations, especially at high latitudes. At low latitudes, the carbon monoxide mixing ratio varies in response to the mean seasonal cycle of surface pressure and shows little variation with topography. At high latitudes, carbon monoxide is depleted in the summer hemisphere by a factor of two or more, while in the winter hemisphere there is relatively higher mixing ratio in regions with low-lying topography. Water vapor shows only modest interannual variations, with the largest observed difference being unusually dry conditions in the wake of the Mars Year 28 global dust storm. Modeling results from the GEM (Global Environmental Multiscale) - Mars general circulation model generally reproduce the observed seasonal and spatial trends and provide insight into the underlying physical processes.

Smith, Michael D.↗

NASA NTRS2018

The Three-Dimensional Bow Shock of Mars as Observed by MAVEN

The Martian magnetosphere is a product of the interaction of Mars with the interplanetary magnetic field and the supersonic solar wind. The location of the bow shock has been previously modeled as conic sections using data from spacecraft such as Phobos 2, Mars Global Surveyor, and Mars Express. The Mars Atmosphere and Volatile EvolutioN (MAVEN) mission spacecraft arrived in orbit about Mars in November 2014 resulting in thousands of crossings to date. We identify over 1,000 bow shock crossings. We model the bow shock as a three-dimensional surface accommodating asymmetry caused by crustal magnetic fields. By separating MAVEN's bow shock encounters based on solar condition, we also investigate the variability of the surface. We find that the shock surface varies in shape and location in response to changes in the solar radiation, the solar wind Mach number, dynamic pressure of the solar wind, and the relative local time location of the strong crustal magnetic fields (i.e., whether they are on the dayside or on the nightside).

Supersonic↗

NASA NTRS2018

Significance of DSMC Computed Aerothermal Environments in the Rarefied Regime for Atmospheric Entry Material Response

During Mars atmospheric entry, the Mars Science Laboratory (MSL) was protected by a 4.5 meters diameter ablative heatshield assembled in 113 tiles. The heatshield was made of NASA's flagship ablative material, the Phenolic Impregnated Carbon Ablator (PICA). Prior work compared the traditional one-dimensional and three-dimensional material response models at different locations in the heatshield. It was observed that the flow was basically one-dimensional in the nose and flank regions, but three-dimensional flow effects were observed in the outer flank. The objective of this work is to study the effects of the aerothermal environment on the material response. We extend prior work by computing aerothermal environments using the direct simulation Monte Carlo (DSMC) code SPARTA and the CFD code Data Parallel Line Relaxation (DPLR). SPARTA is used to compute environment in the rarefied regime prior to 48.4s of entry where the Knudsen number is such that the Navier-Stokes equations can be inaccurate. Similarly to previous work, the DPLR software is used to compute the hypersonic environment for laminar then turbulent boundary layer assumptions from 48.4 s up to 100 s after Entry Interface (EI) along the MSL 08-TPS-02/01a trajectory. We observe that extending the aerothermal environments to times prior to 48.4 s modifies the thermal response of the heat shield at the surface and in-depth; however the effects on the recession are minimal. Additionally, using the assumption of a turbulent boundary layer versus a laminar one leads to higher surface and in-depth temperatures, larger recession, and a displacement of the peak heating and peak recession location.

Aerothermal↗

NASA NTRSDate not supplied

Process Drivers, Inter-model Spread, and a Path Forward: What Do We Know About Arctic Amplification?

Over the recent decades, rapid changes have been observed in the Arctic resulting from enhanced surface warming in the Arctic relative to the rest of the globe, a phenomenon called Arctic Amplification. While surface-based amplification of Arctic warming in response to increased CO2 has been established. The driving mechanisms, relevant processes, and the relative roles of local and remote mechanisms to Arctic Amplification remain unclear. Research over the last decade has made it clear that coupling between the atmosphere, sea ice, and ocean play a key role in Arctic Amplification. This presentation summarizes recent research on the fundamental role that atmosphere-sea ice-ocean interactions and energy exchanges play in driving Arctic Amplification, how these interactions manifest as radiative climate feedbacks, and how these processes influence the differences in the projected Arctic climate change across CMIP5 and 6. We hypothesize that models that simulate larger warming do so by generating a larger local atmospheric circulation response that more effectively redistributes energy drawn from the ocean in sea ice retreat regions Arctic-wide and contributing to a larger increase in downwelling long wave radiation. This process is also fundamentally tied to the Arctic lapse rate feedback.

Patrick Charles Taylor↗

NASA NTRSDate not supplied

Process drivers, inter-model spread, and a path forward: What do we know about Arctic Amplification?

Over the recent decades, rapid changes have been observed in the Arctic resulting from enhanced surface warming in the Arctic relative to the rest of the globe, a phenomenon called Arctic Amplification. While surface-based amplification of Arctic warming in response to increased CO2 has been established. The driving mechanisms, relevant processes, and the relative roles of local and remote mechanisms to Arctic Amplification remain unclear. Research over the last decade has made it clear that coupling between the atmosphere, sea ice, and ocean play a key role in Arctic Amplification. This presentation summarizes recent research on the fundamental role that atmosphere-sea ice-ocean interactions and energy exchanges play in driving Arctic Amplification, how these interactions manifest as radiative climate feedbacks, and how these processes influence the differences in the projected Arctic climate change across CMIP5 and 6. We hypothesize that models that simulate larger warming do so by generating a larger local atmospheric circulation response that more effectively redistributes energy drawn from the ocean in sea ice retreat regions Arctic-wide and contributing to a larger increase in downwelling long wave radiation. This process is also fundamentally tied to the Arctic lapse rate feedback.

Patrick C. Taylor↗

NASA NTRS2018

Technology Development for a Potential Hybrid Mars Ascent Vehicle

With Mars Sample Return mission concepts being considered for launch as early as 2026, technology development to enable this potential campaign is currently underway. One of the critical items in the campaign would be a Mars Ascent Vehicle, which would be responsible for getting the samples from the surface of Mars to orbit around Mars. This would be the first rocket launch from another planet. Therefore, several challenges arise due to the Martian atmosphere and remote location. A technology development program to determine the feasibility of a hybrid rocket for a Mars Ascent Vehicle is entering its fourth year. Highlights and successes of this program will be discussed.

Oglesby, Britt↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

NASA NTRSDate not supplied

Enhancements to Linear Stability-Based, CFD-integrated Transition Prediction for High-Speed Flows

Combining linear stability calculations with computational fluid dynamics (CFD) simulations has great potential for the automated modeling of high-speed flows, especially when adequate information about the configuration and the disturbance environment is available. However, a significant impediment to the applicability of this technique is the lack of an efficient method to calculate the crucial amplification ratio corresponding to the onset of transition in hypersonic flows. This ratio, also known as the "transition N-factor," is dependent upon the freestream disturbance environment as well as the surface properties of the test article. In response to the need for an engineering solution to predict the transition N-factor within conventional hypersonic wind tunnels, this paper presents a data-driven correlation that expands the existing correlations from straight circular cones with a narrow range of half angles to a broader array of axisymmetric configurations. Furthermore, when tested against a chosen dataset that was not used in its calibration, the suggested correlation shows good predictive accuracy with an RMS error of only 6.9%. Although similar accuracy may also be achieved via existing correlations based on similar datasets, predictions based on the proposed correlation have the advantage of not requiring an extensive amount of configuration-specific data. Practical applications often have access to the input parameters needed for this correlation, such as the freestream disturbance intensity, Mach number, and body-based slenderness Reynolds number. Additionally, this correlation outperforms the traditional assumption of a constant N-factor, particularly for configurations with blunted nose geometries. The development of this correlation is grounded in an extensive dataset encompassing conical models with body half-angles varying between 5 degrees and 16 degrees, Mach numbers ranging from 5 to 14, and nosetip-based Reynolds numbers approaching the transition reversal limit for blunt-nosed cones.

CFD↗

DOE OSTI2023

Three-dimensional broadband nonlinear phased array imaging

System include an ultrasonic transducer configured to couple to a nondestructive testing (NDT) sample and configured to produce and direct an ultrasonic probe wave at a selected frequency into a subsurface region of the NDT sample, a 3D laser scanning vibrometer configured to direct a detection beam in a scan area on a surface of the NDT sample and to receive a return beam from the scan area, and to detect, based on the return beam, a 3D motion of the surface across a wideband frequency range, and a processor, and a memory configured with instructions that, when executed by the processor, cause the processor to produce sub-surface image data of the NDT sample at multiple harmonics of the selected frequency in the wideband frequency range based on the detected 3D surface motion, wherein the sub-surface image data describes a nonlinear defect response produced in the NDT sample by interaction of the ultrasonic probe wave with the subsurface region.

Remillieux, Marcel↗

NASA NTRS2012

Reply to ''Comments on 'Why Hasn't Earth Warmed as much as Expected?'''

In response to our article, Why Hasnt Earth Warmed as Much as Expected? (2010), Knutti and Plattner (2012) wrote a rebuttal. The term climate sensitivity is usually defined as the change in global mean surface temperature that is produced by a specified change in forcing, such as a change in solar heating or greenhouse gas concentrations. We had argued in the 2010 paper that although climate models can reproduce the global mean surface temperature history over the past century, the uncertainties in these models, due primarily to the uncertainty in climate forcing by airborne particles, mean that the models lack the confidence to actually constrain the climate sensitivity within useful limits for climate prediction. Knutti and Plattner are climate modelers, and they argued essentially that because the models could reproduce the surface temperature history, the issue we raised was moot. Our response amounts to straightening out this confusion; for the models to be constraining, they must be able to reproduce the surface temperature history with sufficient confidence, not just to match the measurements, but to exclude alternative histories. As before, we concluded that if we can actually make the aerosol measurements using currently available, state-of-the-art techniques, we can determine the aerosol climate forcing to the degree required to constrain that aspect of model climate sensitivity. A technical issue relating to the timescale over which a change in CO2 emissions would be equilibrated in the environmental energy balance was also discussed, again, a matter of differences in terminology.

Schwartz, Stephen E.↗

DOE OSTI2025

Surface Trap Dynamics and Gamma‐Ray Detection Enhancement in Passivated FAPbBr 3 Perovskite Crystals

Perovskite‐based direct radiation detectors offer a compelling platform for room‐temperature gamma spectroscopy due to their high sensitivity, tunable optoelectronic properties, and compatibility with solution processing. While prior studies on formamidinium lead tribromide (FAPbBr 3 ) have shown that surface passivation mitigates deep trap state impact on the charge collection efficiency (CCE), the influence of surface‐based shallow traps on time‐resolved detector response remains largely unexplored. In this article, a digital signal processing (DSP) method is applied to analyze waveform rising edge dynamics in FAPbBr 3 single‐crystal detectors, identifying prompt and delayed charge collection components. Using the second derivative of the collected charge signal, the onset of shallow trap reemission is isolated, occurring 1.1 µs after carrier generation. Surface passivation suppressed deep trap states, shifting carrier occupancy toward shallower traps and extending the temporal window of delayed charge collection. This delayed contribution correlates with measurable changes in the temporal and amplitude distributions of detector events. By leveraging time‐domain filtering informed by these dynamics, a selective enhancement in signal quality and gamma peak‐to‐Compton ratio (PCR) is achieved, while preserving over 90% of photoelectric events. An improvement in the PCR to 1.80, from the original 1.09, is enabled by focusing on high collection efficiency events corresponding to reemitted carriers in the 1.1 to 3 µs range after the generation event. These results demonstrate a pathway for leveraging shallow trap dynamics to enhance spectral fidelity in time‐resolved perovskite detectors.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Plasticity of the Arabidopsis leaf lipidome and proteome in response to pathogen infection and heat stress

Abstract Plants must cope with a variety of stressors during their life cycle, and the adaptive responses to these environmental cues involve all cellular organelles. Among them, comparatively little is known about the contribution of cytosolic lipid droplets (LDs) and their core set of neutral lipids and associated surface proteins to the rewiring of cellular processes in response to stress. Here, we analyzed the changes that occur in the lipidome and proteome of Arabidopsis (Arabidopsis thaliana) leaves after pathogen infection with Botrytis cinerea or Pseudomonas syringae, or after heat stress. Analyses were carried out in wild-type plants and the oil-rich double mutant trigalactosyldiacylglycerol1-1 sugar dependent 1-4 (tgd1-1 sdp1-4) that allowed for an allied study of the LD proteome in stressed leaves. Using liquid chromatography-tandem mass spectrometry-based methods, we showed that a hyperaccumulation of the primary LD core lipid TAG is a general response to stress and that acyl chain and sterol composition are remodeled during cellular adaptation. Likewise, comparative analysis of the LD protein composition in stress-treated leaves highlighted the plasticity of the LD proteome as part of the general stress response. We further identified at least two additional LD-associated proteins, whose localization to LDs in leaves was confirmed by confocal microscopy of fluorescent protein fusions. Taken together, these results highlight LDs as dynamic contributors to the cellular adaptation processes that underlie how plants respond to environmental stress.

Plant Sciences↗