Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials simulations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Equation of Motion for a Grain Boundary

Grain boundary (GB) migration controls many forms of microstructural evolution in polycrystalline materials. Recent theory, simulations, and experiments demonstrate that GB migration is controlled by the motion of discrete line defects or disconnections. We present a continuum equation of motion for grain boundary derived from the underlying discrete disconnection mechanism. We also present an equation of motion for the junctions where multiple grain boundaries meet—as is always the case in a polycrystal. The resulting equation of motion naturally exhibits junction drag—a widely observed phenomena in junction dynamics in solids and liquids.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Stability and conductivity of cation- and anion-substituted LiBH 4 -based solid-state electrolytes

The high-temperature phase of LiBH 4 (HT-LiBH 4 ) exhibits a promisingly high lithium ion conductivity but is unstable at room temperature. We use density functional theory (DFT) calculations to investigate the stabilization effect of halogen and alkali cation/anion substitutions on HT-LiBH 4 as well the underlying mechanism for the high lithium ion conductivity. We find that increasing the substituent concentration enhances the stabilization of HT-LiBH 4 (i.e., the DFT energy difference between the low- and high-temperature forms of substituted LiBH 4 is reduced). Cation/anion substitution also leads to a higher Li defect (vacancy, interstitial, and Frenkel) formation energy, thereby reducing the Li defect (vacancy, interstitial, and Frenkel) concentrations. Using DFT migration barriers input into kinetic Monte Carlo simulations and the Materials INTerface (MINT) framework, here we calculate the room-temperature lithium ion conductivities for Li(BH 4 ) 1-x I x (x = 0.25 and 0.5) and Li 1-y K y BH 4 (y = 0.25). Our calculations suggest that the lower I concentration leads to a higher lithium ion conductivity of 5.7 x10 -3 S/cm compared with that of Li(BH 4 ) 0.5 I 0.5 (4.2 ×10 -5 S/cm) because of the formation of more Li-related defects. Based on our findings, we suggest that the stabilization of HT-LiBH 4 -based lithium ion conductors can be controlled by carefully tuning the cation/anion substituent concentrations to maximize the lithium ionic conductivities of the specific system.

36 MATERIALS SCIENCE↗

Advancements in Constitutive Model Calibration: Leveraging the Power of Full‐Field DIC Measurements and In Situ Load Path Selection for Reliable Parameter Inference

Accurate material characterization and model calibration are essential for computationally supported high-consequence engineering decisions. Historically, characterization and calibration methods (1) use simplified test specimen geometries and global data, (2) cannot guarantee that sufficient characterization data are collected for a specific model of interest, (3) use deterministic methods that provide best-fit parameter values with no uncertainty quantification, and (4) are sequential, inflexible, and time-consuming. This work brings together several recent advancements into an improved workflow called interlaced characterization and calibration (ICC) that advances the state-of-the-art in constitutive model calibration. The ICC paradigm (1) employs tools to efficiently use full-field data to calibrate high-fidelity material models, (2) aligns the data needed with the data collected by adopting an optimal experimental design protocol, (3) quantifies parameter uncertainty through Bayesian inference and (4) incorporates these advancements into a quasi real-time feedback loop. The ICC framework is demonstrated here on the calibration of a material model using simulated full-field data for an aluminium cruciform specimen being deformed biaxially. The cruciform is actively driven through the myopically preferred load path using Bayesian optimal experimental design, which selects load steps that yield the maximum expected information gain (EIG). Principal component analysis (PCA) is performed on the model predictions of full-field displacements, and fast surrogate models are built to approximate the input-output relationships of the expensive finite element model. Furthermore, the tools developed and demonstrated here show that high-fidelity constitutive models can be efficiently and reliably calibrated with quantified uncertainty, thus supporting credible decision-making and potentially increasing the agility of solid mechanics modelling by enabling utilization of computational simulations at earlier stages of the design cycle.

Bayesian optimal experimental design↗

Phonon Thermal Conductivity and Phase Equilibria of Fractal Bi–Sb Nanoparticles

The thermal conductivity component associated with lattice vibrations is one of the quantities determining the thermoelectric activity of a material. We have simulated the dependences of phase composition and the phonon component of the thermal conductivity associated with it on the shape of nanoparticles of a Bi–Sb alloy with an equiatomic composition and with core–shell configuration. The shape of a particle is simulated by a coefficient corresponding to the extent of deviation of the particle shape from spherical or by its fractal dimension. It is shown that mutual solubilities of components depend on the nanoparticle shape and on the mutual arrangement of coexisting phases, and the thermodynamic equilibrium position for particles with complex morphology corresponds to the homogeneous state. Homogenization of a nanoparticle reduces the phonon component of its thermal conductivity by 70–80%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

lanl/nubhlight

nubhlight is a code for simulating disks of materials around black holes formed after the in-spiral and merger of two-black holes. It is based on the open-source code bhlight. nubhlight models all relevant physics required to solve the post-merger disk problem. This includes: general relativity in a static spacetime, neutrino and weak physics, relativistic magnetohydrodynamics, and the ability to use open-sourced tabulated equations of state provided by stellarcollapse.org.

Miller, Jonah↗

COYOTE

COYOTE is designed for the analysis of steady and transient, multi-dimensional, nonlinear heat conduction problems. The spatial discretization technique is based on the Galerkin finite element method. The code contains a library of linear and quadratic elements and incudes bars and shells. COYOTE Implicit and explicit time integration methods, with adaptive time step control, are available for transient problems and fixed-point methods are used for Conjugate gradient iterative methods are used for the matrix solution. Coupled enclosure radiation with efficient view factor computation is included. Simulation capabilities include material motion, dynamic radiation enclosures, contact boundary conditions, multipoint constraints, material (element) addition, and deletion, bulk nodes, chemically reactive materials, and coupling with other mechanics codes. The code is designed for single or multi-processor computing

Gartling, DavidK.↗

ComDMFT

ComDMFT is an ab initio code for simulating correlated quantum materials with crystalline symmetry. It combines DFT or qsGW calculations with impurity problems describing strong on-atom correlations. The impurity problem is set up using Wannier90 and cRPA, and can be solved with DMFT and CTQMC.

Choi, Sangkook↗

Tardigrade-examples V0.1.0

Tardigrade-examples is a repository of computational workflows that exercise the Tardigrade software package. The Tardigrade software package is an implementation of Eringen’s micromorphic continuum theory with capabilities to support multiscale material modeling. These capabilities include homogenization through the Micromorphic Filter, calibration of micromorphic material models, and macroscale simulation in Tardigrade-MOOSE. This repository investigates continuum upscaling of various direct numerical simulations (DNS) conducted in Abaqus finite element (FE), Ratel FE, and GEOS material point method (MPM) software. Verification of the upscaling workflow is first investigated by considering DNS of trivial stress states for homogeneous materials, results of which indicate that classical continuum behavior is recovered as expected. DNS of heterogeneous materials are then considered.

Allard, Thomas↗

Simulation of emergent compaction banding fronts caused by frictional boundaries

This study examines the role of boundary friction in promoting heterogeneous compaction in soft rock specimens loaded at high confining pressure outside the domain of compaction localisation. An elastoplastic constitutive model characterised by tunable hardening/softening behaviour is used to conduct the analyses. Finite-element simulations suggest that material instability is a non-necessary condition for the emergence of compaction fronts. Such fronts propagated as a result of a severe deviation in the local responses induced by frictional constraints. Overall, these findings suggest that boundary effects can bias the assessment of the extent of the compaction localisation domain. Experimental countermeasures and informed model calibration procedures are therefore necessary to minimise such bias and enable more accurate predictions of soft rock compaction.

42 ENGINEERING↗

PROBABILITY BASED CORROSION CONTROL FOR WASTE TANKS - PART II

As part of an ongoing study to evaluate the discontinuity in the corrosion controls at the SRS tank farm, a study was conducted this year to assess the minimum concentrations below 1 molar nitrate, see Figure 1. Current controls on the tank farm solution chemistry are in place to prevent the initiation and propagation of pitting and stress corrosion cracking in the primary steel waste tanks. The controls are based upon a series of experiments performed with simulated solutions on materials used for construction of the tanks, namely ASTM A537 carbon steel (A537). During FY09, an experimental program was undertaken to investigate the risk associated with reducing the minimum molar nitrite concentration required to confidently inhibit pitting in dilute solutions (i.e., less than 1 molar nitrate). The experimental results and conclusions herein provide a statistical basis to quantify the probability of pitting for the tank wall exposed to various solutions with dilute concentrations of nitrate and nitrite. Understanding the probability for pitting will allow the facility to make tank-specific risk-based decisions for chemistry control. Based on previous electrochemical testing, a statistical test matrix was developed to refine and solidify the application of the statistical mixture/amount model to corrosion of A537 steel. A mixture/amount model was identified based on statistical analysis of recent and historically collected electrochemical data. This model provides a more complex relationship between the nitrate and nitrite concentrations and the probability of pitting than is represented by the model underlying the current chemistry control program, and its use may provide a technical basis for the utilization of less nitrite to inhibit pitting at concentrations below 1 molar nitrate. FY09 results fit within the mixture/amount model, and further refine the nitrate regime in which the model is applicable. The combination of visual observations and cyclic potentiodynamic polarization scans indicates a potential for significant inhibitor reductions at nitrate concentrations near 1.0 M without a significant increase in corrosion risk. The complete data sets from FY08 and FY09 testing have determined the statistical basis to confidently inhibit against pitting using nitrite inhibition with the current pH controls. Future testing will complete the spectrum of nitrate concentrations around 1 molar. These results will be combined to provide a complete spectrum for corrosion controls with a risk based component.

36 MATERIALS SCIENCE↗

Radionuclide Retention in Concrete Wasteforms

Assessing long-term performance of Category 3 waste cement grouts for radionuclide encasement requires knowledge of the radionuclide-cement interactions and mechanisms of retention (i.e., sorption or precipitation); the mechanism of contaminant release; the significance of contaminant release pathways; how wasteform performance is affected by the full range of environmental conditions within the disposal facility; the process of wasteform aging under conditions that are representative of processes occurring in response to changing environmental conditions within the disposal facility; the effect of wasteform aging on chemical, physical, and radiological properties; and the associated impact on contaminant release. This knowledge will enable accurate prediction of radionuclide fate when the wasteforms come in contact with groundwater. The information present in the report provides data that (1) measures the effect of concrete wasteform properties likely to influence radionuclide migration; and (2) quantifies the rate of carbonation of concrete materials in a simulated vadose zone repository.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Spreader Bar Radiation Detection Project Data Collection Report

A feasibility assessment of spreader-bar radiation detection (SBRD) systems was commissioned by NA-22 in the summer of 2009. To validate modeling results and allow performance to be based on actual measurements, a full-scale mockup of a SBRD system was built. The full-scale mockup consists of an actual spreader instrumented with 32 sodium iodide gamma detectors. Two sets of data collections were performed using the SBRD mockup. The first set measured the uniformity of radiation detection throughout the Inter-Modal Cargo Container (IMCC). The second set of data collections measured the response of the system to shielded sources. Plywood was used as the simulated cargo (shielding) material and sources were placed at varying depths within it. Both sets of data collections were performed using a forty-foot and a twenty-foot IMCC. In all, over 8700 spectra were collected during the October 2011 through December 2011 time period. This effort is a partnership between Sandia National Laboratories (SNL) and Pacific Northwest National Laboratory (PNNL). Sandia was responsible for design and construction of the SBRD mockup and collection of the data. PNNL was responsible for design of the data collection plan and analysis of the collected data.

Kallenbach, Gene Anthony↗

Evaluation of DUSTRAN Software System for Modeling Chloride Deposition on Steel Canisters

The degradation of steel by stress corrosion cracking (SCC) when exposed to atmospheric conditions for decades is a significant challenge in the fossil fuel and nuclear industries. SCC can occur when corrosive contaminants such as chlorides are deposited on a susceptible material in a tensile stress state. The Nuclear Regulatory Commission has identified chloride-induced SCC as a potential cause for concern in stainless steel used nuclear fuel (UNF) canisters in dry storage. The modeling of contaminant deposition is the first step in predictive multiscale modeling of SCC that is essential to develop mitigation strategies, prioritize inspection, and ensure the integrity and performance of canisters, pipelines, and structural materials. A multiscale simulation approach can be developed to determine the likelihood that a canister would undergo SCC in a certain period of time. This study investigates the potential of DUSTRAN, a dust dispersion modeling system developed by Pacific Northwest National Laboratory, to model the deposition of chloride contaminants from sea salt aerosols on a steel canister. Results from DUSTRAN simulations run with historical meteorological data were compared against measured chloride data at a coastal site in Maine. DUSTRAN’s CALPUFF model tended to simulate concentrations higher than those measured; however, the closest estimations were within the same order of magnitude as the measured values. The decrease in discrepancies between measured and simulated values as the level of abstraction in wind speed decreased suggest that the model is very sensitive to wind speed. However, the influence of other parameters such as the distinction between open-ocean and surf-zone sources needs to be explored further. Deposition values predicted by the DUSTRAN system were not in agreement with concentration values and suggest that the deposition calculations may not fully represent physical processes. Overall, results indicate that with parameter refinement, DUSTRAN has the potential to simulate atmospheric chloride dispersion on steel canisters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Creating physically-based three-dimensional microstructures: Bridging phase-field and crystal plasticity models.

In order to better incorporate microstructures in continuum scale models, we use a novel finite element (FE) meshing technique to generate three-dimensional polycrystalline aggregates from a phase field grain growth model of grain microstructures. The proposed meshing technique creates hexahedral FE meshes that capture smooth interfaces between adjacent grains. Three dimensional realizations of grain microstructures from the phase field model are used in crystal plasticity-finite element (CP-FE) simulations of polycrystalline a -iron. We show that the interface conformal meshes significantly reduce artificial stress localizations in voxelated meshes that exhibit the so-called "wedding cake" interfaces. This framework provides a direct link between two mesoscale models - phase field and crystal plasticity - and for the first time allows mechanics simulations of polycrystalline materials using three-dimensional hexahedral finite element meshes with realistic topological features.

36 MATERIALS SCIENCE↗

Advanced Acid Gas Separation Technology for Clean Power and Syngas Applications

Air Products has developed an acid gas removal technology based on adsorption (Sour PSA) that favorably compares with incumbent AGR technologies. During this DOE-sponsored study, Air Products has been able to increase the Sour PSA technology readiness level by successfully operating a two-bed test system on coal-derived sour syngas at the NCCC, validating the lifetime and performance of the adsorbent material. Both proprietary simulation and data obtained during the testing at NCCC were used to further refine the estimate of the performance of the Sour PSA technology when expanded to a commercial scale. In-house experiments on sweet syngas combined with simulation work allowed Air Products to develop new PSA cycles that allowed for further reduction in capital expenditure. Finally our techno economic analysis of the use the Sour PSA technology for both IGCC and coal-to-methanol applications suggests significant improvement of the unit cost of electricity and methanol compared to incumbent AGR technologies.

08 HYDROGEN↗

HPC4Mfg with Samsung: Making semiconductor devices cool through HPC ab initio simulations

For decades, the semiconductor technology has followed the Moore’s law, making newer devices more powerful and energy efficient. Recently, however, it has reached a point where the performance and the energy efficiency of the device do not improve with the shrinking device size. One of the fundamental reasons of this deviation from the past trend is the interconnect resistance, which becomes larger with the shrinking size. The devices size is so small that the quantum mechanical effects can no longer be ignored and the traditional continuum simulation tools such as TCAD become inadequate. In this project, Samsung Semiconductor Inc. and Lawrence Berkeley National Laboratory has collaborated to perform first of kind device-scale ab initio simulations to optimize materials and interconnect morphology to minimize interconnect resistance. We have tested the use of LS3DF method and the PEtot_trans approach on top of the folded spectrum method (FSM) Escan code to calculate the scattering state, and to study various effects influence the interconnect conductivity. We found that, the LS3DF can be used to calculate such metallic system. On the other hand, the use of Escan code to solve the linear equation is not practical due to the slow convergence. We have implemented a Chebyshev filter technique to calculate a few hundred eigen states near the scattering state energy E, then use these eigen states as preconditioner to solve the linear equation. We have used this approach to study the different factors which affect the interconnect conductivity, including the shape, the point defect, the temperature, and the grain boundary.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Coordinated Multiscale Modeling and Synthesis of Novel Nanostructured Composite Membranes for Solar Fuels Generation (Final Report)

Generation of carbon-based liquid fuels from reduction of CO 2 using solar energy requires the development of improved membranes that provide good ionic conductivity and mechanical properties while minimizing the crossover of gases and reduction products. Using closely coordinated multiscale modeling, synthesis and characterization studies we propose to investigate and develop novel nanostructured composite membranes with applications to conversion of carbon dioxide to storable chemical fuels. The envisioned proton exchange membranes (PEMs) will be based on a support of self- assembling polymer-modified nanoparticles with controllable porosity and tortuosity. The use of a nanoparticle support will provide control of transport and mechanical properties of the membranes. Tuning the copolymer modification of nanoparticles (polymer architectures, brush grafting density) will allow to optimize the ion (proton) transport via the Grotthuss mechanism through narrow hydrated channels while minimizing crossover of gases and reaction products due to the high density of the grafted brush and use of a non-ionic conducting glassy polymers to fill spaces between polymer-grafted nanoparticles. In Phase I synthesis of the copolymers and their attachment to the nanoparticle support will be guided by multiscale simulations that include atomistic molecular dynamics and continuum-level transport simulations. The former will include reactive and non-reactive atomistic simulations that will provide key insight into nanoscale polymer morphology and ion/molecular transport mechanisms need to optimize the copolymer structure. The latter will provide insight into the role of nanoparticle self-assembly on the global transport of ionic and molecular species. The proton conduction and CO 2 /methanol permeability of the membranes will be experimentally characterized as well as simulated and will be correlated with morphology and polymer structure. Prototypes of optimal membranes will be fabricated and characterized at the end of the project. Successful development of improved nanostructured composite PEMs and demonstration of the simulation-guided materials-by-design paradigm will result in our ability to design and synthesize membranes for a wide variety of solar fuels generation and related electrochemical applications.

14 SOLAR ENERGY↗

Large-Scale, GPU-Enhanced DFTB Approaches for Probing Multi-Component Alloys

The major goals of the project are to develop and apply GPU-enhanced density functional theory tight binding (DFTB) calculations for efficient simulations of structural materials of alloy systems. The figure below depicts the GPU algorithmic developments on the left that will be carried out, and the solid-state structures on the right are representative of the complex alloys that can be computed with the GPU-enhanced DFTB approach. The methodology and tools developed in this project encompass accurate intermolecular potentials and GPU enhancements to the density functional tight binding (DFTB) approach for high-throughput ab initio molecular dynamics calculations of multi-component alloys at elevated temperatures. While classical molecular dynamics can handle hundreds of thousands of atoms, it cannot provide a first-principles based description of large, multi-component alloys at the predictive quantum level. At the other extreme, conventional Kohn-Sham DFT methods can probe the true quantum nature of chemical systems; however, these methods cannot tackle the large sizes relevant to these multi-component systems. The DFTB-based ab initio molecular dynamics approach (coupled with our in-house GPU capabilities for enhanced speed) used in this project provides a viable approach for probing these large systems at a quantum level of detail that is significantly faster than current first-principle methods Collectively, the capabilities developed in this project directly respond to DOE HBCU-OMI, AOI 2-1 initiatives by (1) enabling accurate and efficient predictions and (2) bringing a fundamental understanding of structural interactions in these complex systems at elevated temperatures.

20 FOSSIL-FUELED POWER PLANTS↗