Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “liquid crystals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Air Data Probe Anomalies in Flight through Measured High Ice Water Content Conditions

High concentrations of ice crystals in convective storms have caused anomalous air temperature and airspeed readings during commercial and research flight operations. These anomalies occur when ice crystals are ingested in the heated probe inlet, melt or partially melt to liquid water, and then refreeze or remain in a liquid state depending on the probe heat and cloud conditions. In pitot probes, the refreezing may cause complete blockage of the total pressure, which causes airspeed anomalies. In total air temperature probes, the melted ice water may flow near the temperature sensing element and cause the total air temperature reading to approach 0 degree Celsius. During the High Ice Water Content (HIWC) RADAR and HIWC-2022 flight campaigns and the Convective Process Experiment (CPEX-CV) flight campaign, a total of 71 anomalies were recorded on the NASA DC-8 pitot probes when subjected to specific flight and cloud conditions. Similarly, a research TAT probe mounted near the pitot probes had 19 anomalies. This paper presents analyses of the measured natural conditions that led to these TAT and pitot anomalies, identifies two types of pitot probe anomalies, applies a concentration factor to estimate local TWC conditions near the TAT and pitot probes, and identifies the static air temperature and pressure altitude where the anomalies occurred on the Part 33 Appendix D envelope.

Aircraft Icing↗
NASA NTRS1990

1300 K compressive properties of a reaction milled NiAl-AlN composites

When B2 crystal-structure nickel aluminide is subjected to high-intensity mechanical ball milling in a liquid nitrogen bath, or 'cryomilling', an NiAl composite is obtained which contains about 10 vol pct AlN particles. This composition arises from the incorporation of N during cryomilling; during subsequent thermomechanical processing, the N reacts with Al. While compressive testing of extruded or isostatically pressed specimens at 1300 K indicated that strength at relatively fast strain rates is slightly dependent on consolidation method, slower strain rates indicate no clear dependency on densification technique: four different consolidation methods were found to yield similar creep strengths. The creep properties of NiAl-AlN are similar to those of the single-crystal Ni-base superalloy NASAIR 100.

Whittenberger, J. Daniel↗
NASA NTRS2007

Sample mounts for microcrystal crystallography

Sample mounts (10) for mounting microcrystals of biological macromolecules for X-ray crystallography are prepared by using patterned thin polyimide films (12) that have curvature imparted thereto, for example, by being attached to a curved outer surface of a small metal rod (16). The patterned film (12) preferably includes a tapered tip end (24) for holding a crystal. Preferably, a small sample aperture is disposed in the film for reception of the crystal. A second, larger aperture can also be provided that is connected to the sample aperture by a drainage channel, allowing removal of excess liquid and easier manipulation in viscous solutions. The curvature imparted to the film (12) increases the film's rigidity and allows a convenient scoop-like action for retrieving crystals. The polyimide contributes minimally to background and absorption, and can be treated to obtain desired hydrophobicity or hydrophilicity.

Thorne, Robert E.↗
NASA NTRS2009

Sample mounts for microcrystal crystallography

Sample mounts (10) for mounting microcrystals of biological macromolecules for X-ray crystallography are prepared by using patterned thin polyimide films (12) that have curvature imparted thereto, for example, by being attached to a curved outer surface of a small metal rod (16). The patterned film (12) preferably includes a tip end (24) for holding a crystal. Preferably, a small sample aperture is disposed in the film for reception of the crystal. A second, larger aperture can also be provided that is connected to the sample aperture by a drainage channel, allowing removal of excess liquid and easier manipulation in viscous solutions. The curvature imparted to the film (12) increases the film's rigidity and allows a convenient scoop-like action for retrieving crystals. The polyimide contributes minimally to background and absorption, and can be treated to obtain desired hydrophobicity or hydrophilicity.

Thorne, Robert E.↗
DOE OSTI2026

Impact of Molten Gallium on the Microstructure and Corrosion Behavior of Aluminum and Uranium-Aluminum Alloys for Used Nuclear Fuel Reprocessing

Test reactors around the world utilize highly enriched uranium fuel to achieve high neutron fluxes for materials testing. Once spent, the remaining uranium is a valuable resource for subsequent fuel fabrication. However, some of these test reactor cores consist of curved plate-type fuel elements, fabricated using aluminum alloy 6061 (AA6061) cladding to encapsulate a uranium-aluminum alloy (UAlx) fuel matrix. These assemblies require non-standard reprocessing approaches for uranium recovery, as aluminum dissolves readily in acidic solutions, generating large volumes of waste and complicating downstream chemical separations. In this work, we investigate a novel chemical decladding strategy based on the interaction between AA6061/UAlx and molten gallium (Ga). Ga is known to induce severe degradation of aluminum metal through liquid metal embrittlement (LME), even at relatively low Ga concentrations. By penetrating the aluminum crystal lattice, Ga disrupts grain cohesion and facilitates fracture or dissolution of the aluminum matrix. Thermodynamic analysis of the Al–Ga binary phase diagram suggests that Ga may offer a viable pathway to selectively weaken or dissolve the AA6061 cladding, and potentially the aluminum component of the UAlx fuel matrix within. To this end, parametric experiments were performed at 50 °C and 100 °C across a range of Al–Ga atomic fractions. At lower Al fractions, the AA6061 was completely molten after 2 hours of exposure to the Ga metal. In contrast, samples with higher Al fractions (0.9 Al, 0.1 Ga) contained residual solids after 2 hours, which were characterized by microstructural examination using electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). These Al-Ga compositions were also evaluated using FactSage thermodynamic modeling to further elucidate the relationship between phase diagram behavior and LME.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2001

Use of Capillaries for Macromolecular Crystallization in a Cryogenic Dewar

The Enhanced Gaseous Nitrogen (EGN) Dewar is a cryogenic dry shipper with a sealed cylinder inserted inside along with a temperature-monitoring device, and is intended for macromolecular crystallization experiments on the International Space Station. Within the Dewar, each crystallization experiment is contained as a solution within a plastic capillary. The standard procedure for loading samples in these tubes has involved rapid freezing of the precipitant and biomolecule solution directly in liquid nitrogen; this method, however, often results in uncontrolled formation of air voids. These air pockets, or bubbles, then can lead to irreproducible crystallization results. A novel protocol has been developed to prevent formation of bubbles, and this has been tested in the laboratory as well as aboard the International Space Station during a 42-day long mission of July/August of 2001. Furthermore, gain or loss of mass from solutions within the capillaries revealed that mass transport amongst separated tubes occurred, and that this mass transport was determined by the hygroscopic character of a solution contained in any given tube. The sample volume and the surface area of the plastic capillary tube also related to the observed mass transport.

Ciszak, Ewa↗
DOE OSTI2022

Ionic Liquid Gating of SrTiO 3 Lamellas Fabricated with a Focused Ion Beam

Here, in this work, we combine two previously incompatible techniques for defining electronic devices: shaping three-dimensional crystals by focused ion beam (FIB), and two-dimensional electrostatic accumulation of charge carriers. The principal challenge for this integration is nanometer-scale surface damage inherent to any FIB-based fabrication. We address this by using a sacrificial protective layer to preserve a selected pristine surface. The test case presented here is accumulation of 2D carriers by ionic liquid gating at the surface of a micron-scale SrTiO 3 lamella. Preservation of surface quality is reflected in superconductivity of the accumulated carriers. This technique opens new avenues for realizing electrostatic charge tuning in materials that are not available as large or exfoliatable single crystals, and for patterning the geometry of the accumulated carriers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS2004

Semiconductor Crystal Growth in Static and Rotating Magnetic fields

Magnetic fields have been applied during the growth of bulk semiconductor crystals to control the convective flow behavior of the melt. A static magnetic field established Lorentz forces which tend to reduce the convective intensity in the melt. At sufficiently high magnetic field strengths, a boundary layer is established ahead of the solid-liquid interface where mass transport is dominated by diffusion. This can have a significant effect on segregation behavior and can eliminate striations in grown crystals resulting from convective instabilities. Experiments on dilute (Ge:Ga) and solid solution (Ge-Si) semiconductor systems show a transition from a completely mixed convective state to a diffusion-controlled state between 0 and 5 Tesla. In HgCdTe, radial segregation approached the diffusion limited regime and the curvature of the solid-liquid interface was reduced by a factor of 3 during growth in magnetic fields in excess of 0.5 Tesla. Convection can also be controlled during growth at reduced gravitational levels. However, the direction of the residual steady-state acceleration vector can compromise this effect if it cannot be controlled. A magnetic field in reduced gravity can suppress disturbances caused by residual transverse accelerations and by random non-steady accelerations. Indeed, a joint program between NASA and the NHMFL resulted in the construction of a prototype spaceflight magnet for crystal growth applications. An alternative to the suppression of convection by static magnetic fields and reduced gravity is the imposition of controlled steady flow generated by rotating magnetic fields (RMF)'s. The potential benefits of an RMF include homogenization of the melt temperature and concentration distribution, and control of the solid-liquid interface shape. Adjusting the strength and frequency of the applied magnetic field allows tailoring of the resultant flow field. A limitation of RMF's is that they introduce deleterious instabilities above a critical magnetic field value. Growth conditions in which static magnetic fields rotational magnetic fields, and reduced gravitational levels can have a beneficial role will be described.

Volz, Martin↗
NASA NTRS2015

Determination of the Contact Angle Based on the Casimir Effect

On a macroscopic scale, a nonreactive liquid partially covering a homogeneous solid surface will intersect the solid at an angle called the contact angle. For molten metals and semiconductors, the contact angle is materially dependent upon both the solid and liquid and typical values fall in the range 80-170 deg, depending on the crucible material. On a microscopic scale, there does not exist a precise and sharp contact angle but rather the liquid and solid surfaces merge smoothly and continuously. Consider the example of the so called detached Bridgman crystal growth process. In this technique, a small gap is formed between the growing crystal and the crucible. At the crystal/melt interface, a meniscus ring is formed. Its width can be in the range of a few micrometers, approaching a microscopic scale. It then becomes questionable to describe the shape of this meniscus by the contact angle. A more advanced treatment of the interface is needed and here we propose such a refined model. The interaction of the liquid surface with the solid can be calculated by considering two forces: a short-range repulsive force and a longer range (up to a few micrometers) Casimir or van der Waals force.

Mazuruk, Konstantin↗
NASA NTRSDate not supplied

A Study of Ice-Crystal Icing Erosion Using the NASA Icing Research Tunnel and Propulsion Systems Laboratory

In ice-crystal icing, ice erosion can occur simultaneously with ice accretion. This paper presents a proof-of-concept experimental study that attempts to isolate and quantify ice erosion. The experiments took place at the NASA Icing Research Tunnel and Propulsion Systems Laboratory in 2017 and 2018. The test procedure involved first generating an ice accretion on various NACA 0012 airfoil models using a supercooled liquid water or mixed-phase icing cloud and, subsequently, exposing that ice accretion to an ice crystal cloud. The resulting ice mass decay rates were analyzed in terms of an erosion term, defined as the ratio of the eroded mass flux to impinging mass flux. The erosion term generally increased with airspeed with a value of 1.8% at air velocities of 270 knots and increasing to just over 6% at 360 knots. A preliminary correlation for ice erosion is developed for use in ice accretion models subject to the conditions tested. The study revealed several challenges, both experimental and analytical, including spray bar nozzle freeze-out as well as measurement of the cloud melt ratio to ensure freeze-out.

Icing↗
DOE OSTI2024

Functionalization of Cathode–Electrolyte Interface with Ionic Liquids for High-Performance Quasi-Solid-State Lithium–Sulfur Batteries: A Low-Sulfur Loading Study

We introduce a quasi-solid-state electrolyte lithium-sulfur (Li–S) battery (QSSEB) based on a novel Li-argyrodite solid-state electrolyte (SSE), Super P–Sulfur cathode, and Li-anode. The cathode was prepared using a water-based carboxymethyl cellulose (CMC) solution and styrene butadiene rubber (SBR) as the binder while Li6PS5F0.5Cl0.5 SSE was synthesized using a solvent-based process, via the introduction of LiF into the argyrodite crystal structure, which enhances both the ionic conductivity and interface-stabilizing properties of the SSE. Ionic liquids (IL) were prepared using lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as the salt, with pre-mixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent, and they were used to wet the SSE–electrode interfaces. The effect of IL dilution, the co-solvent amount, the LiTFSI concentration, the C rate at which the batteries are tested and the effect of the introduction of SSE in the cathode, were systematically studied and optimized to develop a QSSEB with higher capacity retention and cyclability. Interfacial reactions occurring at the cathode–SSE interface during cycling were also investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and X-ray photoelectron spectroscopy supported by ab initio molecular dynamics simulations. This work offers a new insight into the intimate interfacial contacts between the SSE and carbon–sulfur cathodes, which are critical for improving the electrochemical performance of quasi-solid-state lithium–sulfur batteries.

25 ENERGY STORAGE↗
NASA NTRS2002

Use of Capillaries for Macromolecular Crystallization in a Cryogenic Dewar

The enhanced gaseous nitrogen (EGN) dewar is a cryogenic dry shipper with a sealed cylinder inserted inside along with a temperature monitoring device, and is intended for macromolecular crystallization experiments on the International Space Station. Within the dewar, each crystallization experiment is contained as a solution within a plastic capillary tube. The standard procedure for loading samples in these tubes has involved rapid freezing of the precipitant and biomolecular solution, e.g., protein, directly in liquid nitrogen; this method, however, often resulted in uncontrolled formation of air voids, These air pockets, or bubbles, can lead to irreproducible crystallization results. A novel protocol has been developed to prevent formation of bubbles, and this has been tested in the laboratory as well as aboard the International Space Station during a 42-day long mission of July/August 2001. The gain or loss of mass from solutions within the plastic capillaries revealed that mass transport occurred among separated tubes, and that this mass transport was dependent upon the hygroscopic character of the solution contained in any given tube. The surface area of the plastic capillary tube also related to the observed mass transport. Furthermore, the decreased mass of solutions of-protein correlated to observed formation of protein crystals.

Ciszak, Ewa↗
NASA NTRS1995

Dynamic Instability of Solidification Fronts and Formation of Transverse Layered Structures

A plane front of crystallization in a unidirectional process of solidification of a binary melt or a solution is shown to be unstable with respect to virtual perturbations of the front velocity within some region of physical and operating parameters. This dynamic instability has nothing in common with morphological instability of the front also possible under certain conditions. It gives rise to the origination of a self-oscillating regime of solidification. The oscillations of the front velocity are accompanied by oscillations of other relevant variables, such as the melt concentration and temperature at the front. What is most important is that this provides for a natural explanation of phenomena of the formation of ordered striations commonly observed when producing alloys and withdrawing crystals. A theory of nonlinear instability of the solidification front is developed which also allows for properties of both self-oscillating regimes of solidification and transverse layered structures it allows to be described in an explicit form, without introducing any additional hypotheses and empirical parameters. Apart from other things, the properties are strongly dependent on convective transport originated in consequence of a difference between the densities of the liquid melt and solid alloy. The theory results in a remarkably good agreement with experimental evidence on crystal withdrawal obtained in normal gravity and under space flight conditions. The problem of interplay between modes of the dynamic and morphological types of instability is also discussed. There are parametric regions in which either only one of these types occurs or both of them arise simultaneously.

Buyevich, Yu A.↗
DOE OSTI2019

Spin-liquid-like state in pure and Mn-doped TbInO 3 with a nearly triangular lattice

Inelastic neutron scattering studies in single crystals of TbInO 3 and TbIn 0.95 Mn 0.05 O 3 with nearly-triangular antiferromagnetic lattice are reported. At low energies, a broad and apparently gapless continuum of magnetic excitations, located at the triangular lattice (TL) Brillouin zone boundary, is observed. The data are well described by the uncorrelated nearest-neighbor valence bonds model. At higher energies, a broad excitation branch dispersing from the TL zone boundary is observed. No signs of static magnetic order are found down to the temperatures two orders of magnitude smaller than the effective interaction energy. The fluctuating magnetic moment exceeds two thirds of the Tb 3+ free-ion value and is confined to the TL plane. These observations are consistent with a TL-based spin liquid state in TbInO 3 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1992

Numerical study of low-current steady arcs

The development of a high-efficiency CW YLF laser doped with Er,Tm,Ho: and featuring a strongly focusing resonator that collects a high density of pump power on the active crystal is described. The emission is investigated at 2.06 microns and a tuning range both at liquid-nitrogen (77 K) and at dry-ice (210 K) temperature. The noise characteristics and the long-term power stability of the laser is studied with an eye to employing this source for high-resolution spectroscopy in the 2-micron wavelength region. The detection of several absorption lines of NH3 at low pressure is described. The output power of the laser as a function of the power impinging on the crystal for different transmission of the output mirror is illustrated. The best result obtained is 1.46 W output for 3.2 W of argon pump. The minimum threshold achieved is 3.5 mW with a 1-percent transmission mirror. It is concluded that it is possible to develop a highly efficient Ho:YLF laser featuring low noise and sufficient tunability for high-resolution spectroscopy in the 2-micron region.

Kim, S. C.↗
NASA NTRS1999

Thermophysical Property Measurements of Molten Semiconductors in 1-g and Reduced-g Condition

Understanding and controlling the formation kinetics of varieties of crystal imperfections such as point defects, non uniform distribution of doping atoms, and impurity atoms in growing crystals are very important. Theoretical (numerical) modeling of the crystal growth process is an essential step to achieving these objectives. In order to obtain reliable modeling results, input parameters, i.e. various thermophysical parameters, must be accurate. The importance of accurate thermophysical properties of semiconductors in crystal growth cannot be overly emphasized. The total hemispherical emissivity, for instance, has a dramatic impact on the thermal environment. It determines the radiative emission from the surface of the melt which determines to a large extent the profile of the solidified crystal. In order to understand the convection and the turbulence in a melt, viscosity becomes an important parameter. The liquid surface tension determines the shape of the liquid-atmosphere interface near the solid-liquid-atmosphere triple point. Currently used values for these parameters are rather inaccurate, and this program intends to provide more reliable measurements of these thermophysical properties. Thus, the objective of this program is in the accurate measurements of various thermophysical properties which can be reliably used in the modeling of various crystal growth processes. In this program, thermophysical properties of molten semiconductors, such as Si, Ge, Si-Ge, and InSb will be measured as a function of temperature using the High Temperature Electrostatic Levitator at JPL. Each material will be doped by different kinds of impurities at various doping levels. Thermophysical properties which will be measured include: density, thermal expansion coefficient, surface tension, viscosity, specific heat, hemispherical total emissivity, and perhaps electrical and thermal conductivities. Many molten semiconductors are chemically reactive with crucibles. As a result, these dispersed impurities in the melts tend to substantially modify the properties of pure semiconductors. Sample levitation done in a vacuum clearly helps maintain the sample purity. However, in the 1-g environment, all gravity caused effects such as convection, sedimentation and buoyancy are still present in the sample. In addition, large forces needed to levitate a sample in the presence of the gravity can cause additional flows in the melt. The use of the High Temperature Electrostatic Levitator (HTESL) for the present research is a recent development and little is known about the flows induced by the electrostatic forces. In this ground base program, we will define the limits of HTESL technology as various thermophysical properties of molten semiconductors are measured.

Rhim, Won-Kyu↗
DOE OSTI2021

Low-energy magneto-optics of Tb 2 Ti 2 O 7 in a [111] magnetic field

The pyrochlore magnet Tb 2 Ti 2 O 7 shows a lack of magnetic order to low temperatures and is considered to be a quantum spin liquid candidate. Here we perform time-domain THz spectroscopy on high-quality Tb 2 Ti 2 O 7 crystals and study the low-energy excitations as a function of [111] magnetic field with high energy resolution. The low-energy crystal-field excitations change their energies anomalously under magnetic field. Despite several sharp field-dependent changes, we show that the material's spectrum can be described not by phase transitions but by field-dependent hybridization between the low-energy crystal-field levels. We highlight the strong coupling between spin and lattice degrees of freedom in Tb 2 Ti 2 O 7 as evidenced by the magnetic-field tunable crystal-field environment. Calculations based on single ion physics with field-induced symmetry reduction of the crystal-field environment can reproduce our data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Communication—Electrodeposition of Indium Directly on Silicon

Direct electrodeposition of indium onto silicon paves the way for advances in microelectronics, photovoltaics, and optoelectronics. Indium is generally electrodeposited onto silicon utilizing a physically or thermally deposited metallic seed layer. Eliminating this layer poses benefits in microelectronics by reducing resistive interfaces and in vapor-liquid-solid conversion to III-V material by allowing direct contact to the single-crystal silicon substrate for epitaxial conversion. We investigated conditions to directly electrodeposit indium onto n-type Si(100). We illustrate that a two-step galvanostatic plating at low temperatures can consistently produce smooth, continuous films of indium over large areas, in bump morphologies, and conformally into inverted pyramids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗