Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Three-step labyrinth seal for high-performance turbomachines

A three-step labyrinth seal with 12, 11, and 10 labyrinth teeth per step, respectively, was tested under static (nonrotating) conditions. The configuration represented the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump). The test data included critical mass flux and pressure profiles over a wide range of fluid conditions at concentric, partially eccentric, and fully eccentric seal positions. The seal mass fluxes (leakage rates) were lower over the entire range of fluid conditions tested than those for data collected for similar straight and three-step cylindrical seals, and this conformed somewhat to expectations. However, the pressure profiles for the eccentric positions indicated little, if any, direct stiffness for this configuration in contrast to significant direct stiffness reported for the straight and three-step cylindrical seals over the range of test conditions. Seal dynamics depend on geometric configuration, inlet and exit parameters, fluid phase, and rotation. The method of corresponding states was applied to the mass flux data, which were found to have a pressure dependency for helium.

Hendricks, Robert C.↗
NASA NTRS1986

Solar concentrator materials development

Materials with potential applications in reflective and refractive solar dynamic concentrators are tested for resistance to atomic oxygen degradation. It is found that inorganic coatings such as MgF2, SiO(x), and ITO provide excellent protection for reflective surfaces while organic materials are much more susceptible to erosion and mass loss. Of the organic polymers tested, the silicones have the highest intrinsic resistance to atomic oxygen degradation.

Morel, D. E.↗
NASA NTRS1987

Sensitivity studies and a simple ozone perturbation experiment with a truncated two-dimensional model of the stratosphere

The 1-1/2-D model of Holton (1986), which is actually a highly truncated two-dimensional model, describes latitudinal variations of tracer mixing ratios in terms of their projections onto second-order Legendre polynomials. The present study extends the work of Holton by including tracers with photochemical production in the stratosphere (O3 and NOy). It also includes latitudinal variations in the photochemical sources and sinks, improving slightly the calculated global mean profiles for the long-lived tracers studied by Holton and improving substantially the latitudinal behavior of ozone. Sensitivity tests of the dynamical parameters in the model are performed, showing that the response of the model to changes in vertical residual meridional winds and horizontal diffusion coefficients is similar to that of a full two-dimensional model. A simple ozone perturbation experiment shows the model's ability to reproduce large-scale latitudinal variations in total ozone column depletions as well as ozone changes in the chemically controlled upper stratosphere.

Stordal, Frode↗
NASA NTRS1988

Observations of intense trapped electron fluxes at synchronous altitudes

The concept of flux limiting in the outer radiation belt proposed by Kennel and Petschek (1966) has been tested in a dynamic situation by using data acquired with instruments aboard the SCATHA satellite. A case-by-case analysis of 12 events for evidence of flux limiting under various magnetospheric conditions is made. The reuslts indicate qualitative agreement with the flux limiting theory for all the events studied. Even the quiescent events and hard-spectrum events are consistent with flux limiting. The limiting flux level at any instant appears to depend strongly on the recent history of the trapped electrons and plasma in the outer magnetosphere.

Davidson, G. T.↗
NASA NTRS1988

Pyro shock simulation: Experience with the MIPS simulator

The Mechanical Impulse Pyro Shock (MIPS) Simulator at GE Astro Space Division is one version of a design that is in limited use throughout the aerospace industry, and is typically used for component shock testing at levels up to 10,000 response g's. Modifications to the force imput, table and component boundary conditions have allowed a range of test conditions to be achieved. Twelve different designs of components with weights up to 23 Kg are in the process or have completed qualification testing in the Dynamic Simulation Lab at GE in Valley Forge, Pa. A summary of the experience gained through the use of this simulator is presented as well as examples of shock experiments that can be readily simulated at the GE Astro MIPS facility.

Dwyer, Thomas J.↗
NASA NTRS1989

Space Shuttle Main Engine structural analysis and data reduction/evaluation. Volume 6: Primary nozzle diffuser analysis

The primary nozzle diffuser routes fuel from the main fuel valve on the Space Shuttle Main Engine (SSME) to the nozzle coolant inlet mainfold, main combustion chamber coolant inlet mainfold, chamber coolant valve, and the augmented spark igniters. The diffuser also includes the fuel system purge check valve connection. A static stress analysis was performed on the diffuser because no detailed analysis was done on this part in the past. Structural concerns were in the area of the welds because approximately 10 percent are in areas inaccessible by X-ray testing devices. Flow dynamics and thermodynamics were not included in the analysis load case. Constant internal pressure at maximum SSME power was used instead. A three-dimensional, finite element method was generated using ANSYS version 4.3A on the Lockheed VAX 11/785 computer to perform the stress computations. IDEAS Supertab on a Sun 3/60 computer was used to create the finite element model. Rocketdyne drawing number RS009156 was used for the model interpretation. The flight diffuser is denoted as -101. A description of the model, boundary conditions/load case, material properties, structural analysis/results, and a summary are included for documentation.

Foley, Michael J.↗
NASA NTRS1989

Review and analysis of the DNW/Model 360 rotor acoustic data base

A comprehensive model rotor aeroacoustic data base was collected in a large anechoic wind tunnel in 1986. Twenty-six microphones were positioned around the azimuth to collect acoustic data for approximately 150 different test conditions. A dynamically scaled, blade-pressure-instrumented model of the forward rotor of the BH360 helicopter simultaneously provided blade pressures for correlation with the acoustic data. High-speed impulsive noise, blade-vortex interaction noise, low-frequency noise, and broadband noise were all captured in this extensive data base. Trends are presentes for each noise source, with important parametric variations. The purpose of this paper is to introduce this data base and illustrate its potential for predictive code validation.

Zinner, R. A.↗
NASA NTRS1990

Continuous assimilation of Geosat altimetric sea level observations into a numerical synoptic ocean model of the California Current

The Geosat altimetric sea level observations for the period from January to December 1987 were continuously assimilated into a realistic wind-driven numerical synoptic ocean model of the California Current in order to evaluate the effectiveness of using a realistic synoptic ocean model for interpolating (dynamically) real altimetric sea level observations onto a regular grid. The accuracy of dynamical interpolation was tested by comparing the gridded sea level residuals to ones estimated from in situ observations (by expendable bathythermographs) collected in the California Current region during the same period. The comparison yielded nearly exact agreement at low frequency (i.e., semiannual cycle), but less agreement on month-to-month time scales of variability, possibly due to the unfiltered nature of the in situ estimates.

White, Warren B.↗
NASA NTRS1990

Aerodynamic Effect of Strakes on Two-Dimensional Tail Boom Models of the OH-58A and the OH-58D Helicopters

During hover and low speed flight, helicopters experience significant aerodynamic forces on the tail boom caused by the wake from the main and tail rotors and by crosswinds. These effects were simulated during a study conducted in the Langley 14 by 22 Foot Subsonic Tunnel on a 136 percent scaled 2-D tail boom model with cross sections representative of those on the U.S. Army OH-58A and the OH-58D helicopters. The effects of longitudinal strakes attached to the cross sections were studied. To obtain the aerodynamic forces acting on the cross sections, the flow incidence range on the scaled models was varied from -45 to 90 degrees and the models were tested through a dynamic pressure range of 5 to 15 psf. The results of the OH-58A and the OH-58D configurations show a significant improvement at conditions which represent right sideward flight by reducing the adverse aerodynamic side force when the strakes are installed. These data were used to calculate a change in tail rotor power for the full scale flight vehicle and indicated approx. a 5 to 6 percent average savings in right sideward flight for the critical velocity range of 0 to 30 knots. Increases in the tail boom normal force were noted due to the strakes. The results indicate a potential for reducing the directional control and tail rotor thrust required in the critical hover and right sideward flight speed range with a calculated minimum increase to main rotor power required and an overall net improvement in power of 0.5 percent for both the OH-58A and OH-58D.

Crowell, Cynthia A.↗
NASA NTRS1991

Static strain and vibration characteristics of a metal semimonocoque helicopter tail cone of moderate size

The results are presented of an analytic and experimental research program involving a Sikorsky S-55 helicopter tail cone directed ultimately to the improved structural analysis of airframe substructures typical of moderate sized helicopters of metal semimonocoque construction. Experimental static strain and dynamic shake-testing measurements are presented. Correlation studies of each of these tests with a PC-based finite element analysis (COSMOS/M) are described. The tests included static loadings at the end of the tail cone supported in the cantilever configuration as well as vibrational shake-testing in both the cantilever and free-free configurations.

Bielawa, Richard L.↗
NASA NTRS1991

Aerothermodynamics for United States advanced programs

A series of graphics relating to aerothermodynamics is presented. They following topics are shown: space transportation architecture options and systems, vehicle shapes and design goals, aerothermodynamics (including hypersonic entry), computational fluid dynamics, ground based testing, aeroassist environment, and airbreathing propulsion.

Piland, William M.↗
NASA NTRS1991

Nuclear electric propulsion development and qualification facilities

This paper summarizes the findings of a Tri-Agency panel consisting of members from the National Aeronautics and Space Administration (NASA), U.S. Department of Energy (DOE), and U.S. Department of Defense (DOD) that were charged with reviewing the status and availability of facilities to test components and subsystems for megawatt-class nuclear electric propulsion (NEP) systems. The facilities required to support development of NEP are available in NASA centers, DOE laboratories, and industry. However, several key facilities require significant and near-term modification in order to perform the testing required to meet a 2014 launch date. For the higher powered Mars cargo and piloted missions, the priority established for facility preparation is: (1) a thruster developmental testing facility, (2) a thruster lifetime testing facility, (3) a dynamic energy conversion development and demonstration facility, and (4) an advanced reactor testing facility (if required to demonstrate an advanced multiwatt power system). Facilities to support development of the power conditioning and heat rejection subsystems are available in industry, federal laboratories, and universities. In addition to the development facilities, a new preflight qualifications and acceptance testing facility will be required to support the deployment of NEP systems for precursor, cargo, or piloted Mars missions. Because the deployment strategy for NEP involves early demonstration missions, the demonstration of the SP-100 power system is needed by the early 2000's.

Dutt, D. S.↗
NASA NTRS1991

The Personnel Launch System - A lifting body approach

A lifting-body approach to the sign of a Personnel Launch System spacecraft for Space Station crew missions is defined. This paper reviews the characteristics and capabilities of this spacecraft the HL-20. Launch vehicle options are examined and recent findings from wind tunnel tests, tests of landing dynamics and handling qualities, and human factors research using a full-scale research model are reviewed.

Talay, Theodore A.↗
NASA NTRS1993

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: McDonnell-Douglas Helicopter Company achievements

This paper presents a summary of some of the work performed by McDonnell Douglas Helicopter Company under NASA Langley-sponsored rotorcraft structural dynamics program known as DAMVIBS (Design Analysis Methods for VIBrationS). A set of guidelines which is applicable to dynamic modeling, analysis, testing, and correlation of both helicopter airframes and a large variety of structural finite element models is presented. Utilization of these guidelines and the key features of their applications to vibration modeling of helicopter airframes are discussed. Correlation studies with the test data, together with the development and applications of a set of efficient finite element model checkout procedures, are demonstrated on a large helicopter airframe finite element model. Finally, the lessons learned and the benefits resulting from this program are summarized.

Toossi, Mostafa↗
NASA NTRS1991

U.S. perspective on technology demonstration experiments for adaptive structures

Evaluation of design concepts for adaptive structures is being performed in support of several focused research programs. These include programs such as Precision Segmented Reflector (PSR), Control Structure Interaction (CSI), and the Advanced Space Structures Technology Research Experiment (ASTREX). Although not specifically designed for adaptive structure technology validation, relevant experiments can be performed using the Passive and Active Control of Space Structures (PACOSS) testbed, the Space Integrated Controls Experiment (SPICE), the CSI Evolutionary Model (CEM), and the Dynamic Scale Model Test (DSMT) Hybrid Scale. In addition to the ground test experiments, several space flight experiments have been planned, including a reduced gravity experiment aboard the KC-135 aircraft, shuttle middeck experiments, and the Inexpensive Flight Experiment (INFLEX).

Aswani, Mohan↗
NASA NTRS1988

On-orbit parametric identification methodology

On-orbit system identification (ID) of large space systems is essential for various reasons. For example, the complex composite structure of such systems cannot be ground-tested; their structural dynamic characteristics must be known accurately in order to accomplish active control. Furthermore, such capability can be used to characterize/identify various disturbances. The identification process is consisted of four principal elements: (1) modeling, (2) the estimation algorithm, (3) input system, and (4) measurement system. These elements are highly correlated and all togerher determine the success of the identification problem. Accurate modeling of large space systems is the most important element of the identification process. Large flexible structures are non-linear and infinite dimensional systems with highly coupled parameters and low frequency packed modes. In addition, these systems are subject to stochastic and time-varying disturbances, they have structural parameters which can vary due to on-orbit assembly deployment, and operations. These systems are generally; however, represented by constant coefficient, finite order differential equations. The non-linearities, coupling and noise effects are also often neglected. Moreover, identification experiment designs which lead to highly complex optimization problems usually require the simultaneous choice of ID algorithm, sensor, and actuator type and placement. On-orbit bandwidth and power restrictions on excitation, limited data window, and restrictions on sensor/actuator type, placement and number, has led to practical questions of implementations.

Hadaegh, Fred Y.↗
NASA NTRS1990

Sensitivity analysis of the optimal solution obtained from the structural damage indentification process

An identification procedure proposed by Shen and Taylor to determine the crack characteristics (location and size of the crack) from dynamic measurements is tested. This procedure was based on minimization of either the 'mean-square' measure of difference between measurement data (natural frequencies and mode shapes) and the corresponding predictions obtained from the computational model. The procedure is tested for simulated damage in the form of symmetric cracks in a simply-supported Bernoulli-Euler beam. The sensitivity of the solution of damage identification problems to the values of parameters that characterize damage is discussed. A sensitivity formula is derived.

Shen, Mo-How H.↗
NASA NTRS1995

Parallel volume ray-casting for unstructured-grid data on distributed-memory architectures

As computing technology continues to advance, computational modeling of scientific and engineering problems produces data of increasing complexity: large in size and unstructured in shape. Volume visualization of such data is a challenging problem. This paper proposes a distributed parallel solution that makes ray-casting volume rendering of unstructured-grid data practical. Both the data and the rendering process are distributed among processors. At each processor, ray-casting of local data is performed independent of the other processors. The global image composing processes, which require inter-processor communication, are overlapped with the local ray-casting processes to achieve maximum parallel efficiency. This algorithm differs from previous ones in four ways: it is completely distributed, less view-dependent, reasonably scalable, and flexible. Without using dynamic load balancing, test results on the Intel Paragon using from two to 128 processors show, on average, about 60% parallel efficiency.

Ma, Kwan-Liu↗