Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “co2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Conjugate Heat Transfer Analysis of the Supercritical CO2 Based Counter Flow Compact 3D Heat Exchangers

Compact heat exchangers using supercritical fluids such as CO2 are preferred due to their high heat transfer capacity and smaller footprint. Three-dimensional conjugate forced convection heat transfer analysis was performed on several shell-and-tube counter-flow microchannel heat exchangers. Numerical simulations were conducted to test effect of change in mass flow rate, hydraulic diameter and various cross sections on the heat transfer. Increasing mass flow rate improved heat transfer up to a maximum value and then decreased downstream with increasing turbulence. Maximum heat transfer was obtained for the micro channel with the smallest hydraulic diameter. Amongst the cross sections analyzed (circular, square, circular with radial ribs, and square with radial ribs), the most uniform distribution of temperature and maximum heat transfer were obtained for circular cross section with radial ribs. An optimally efficient operation of such a heat exchanger can be attained by considering these factors during multi-objective constrained optimization of geometric parameters and requirements for additive manufacturing of such compact heat exchangers.

Chitale, Janhavi↗
DOE OSTI2021

Compatibility of Steels in Supercritical CO2 at 450°-650°C

Supercritical CO2 (sCO2) power cycles, particularly direct-fired cycles, have the possibility of revolutionizing clean fossil energy. However, in the lower temperature sections of the cycle, lower cost steels are needed in order to lower the cost of the sCO2 technology. Representative 9 and 12%Cr steels and conventional and advanced austenitic steels are being evaluated at 450-650°C using mass change, bulk carbon (C) content and room temperature tensile properties to determine the maximum use temperatures for both direct- and indirect-fired sCO2 cycles. After 1000 h exposures in research grade (RG) sCO2 at 300 bar and RG sCO2 with 1% O2 and 0.1% H2O additions, the results suggest that increasing the Cr content from 9 to 12% yielded no signficant benefit under these conditions but the higher Cr and Ni contents in S31025 provided better compatibility in RG sCO2 at 650°C but limited benefit at 550°C with impurities. For S31609, the formation of Fe-rich oxide after exposure to RG sCO2 at 650°C resulted in both an increase in the bulk C content and a large drop in room temperature ductility. The evidence suggests thin, protective oxides prevented C ingress in these conditions.

Pint, Bruce↗
DOE OSTI2021

A Comparative Techno-Economic Analysis of Renewable Methanol Synthesis Pathways from Biomass and CO2: Preprint

Global demand for methanol as both a chemical precursor and a fuel additive is rising. At the same time, numerous sustainable methanol production pathways are under development which, if commercialized, could present significant environmental benefits over traditional methanol synthesis pathways. There is a need to harmonize the analyses of sustainable pathways using a consistent techno-economic approach to evaluate the potential for commercialization of various pathways. This analysis considers economic and environmental factors critical to market acceptance of three sustainable pathways versus a commercial baseline. We suggest that biomass gasification to methanol represents a near-term viable pathway with high technology readiness level and commercially competitive market price. However, long-term solutions should consider CO2 electrolysis pathways which offer further improvements in sustainability metrics to support global decarbonization efforts.

biomass↗
DOE OSTI2022

Compatibility Of Steels At 450°-650°C In Supercritical CO2 With O2 And H2O Additions

Direct-fired supercritical CO2 (sCO2) power cycles are being commercialized to revolutionize fossil energy as a low-emission power source. However, the cycle will increase O2 and H2O in the sCO2 and the implications of these additions have not been fully studied, particularly for lower cost steels that are needed in the lower temperature segments of the plant. Representative 9 and 12%Cr ferritic-martensitic (FM) steels and conventional and advanced austenitic steels were evaluated at 450-650°C to determine the maximum use temperatures in sCO2 with 1%O2 and 0.1%H2O at 300 bar. Compared to research grade (low impurity) sCO2 in indirect-fired cycles, the mass gains and scale thickness were not significantly changed for FM steels: both formed thick duplex Fe-rich scales. For stainless steels, higher mass gains were observed in all cases with increased Fe-rich oxide nodule formation. After 1000h at 650°C, the measured bulk C content was high for all of the steels with the addition of impurities suggesting a lower maximum operating temperature for steels. The post-exposure impact of the environment on room temperature tensile properties also will be discussed.

Pint, Bruce↗
DOE OSTI2022

Multiphysics Simulation of Supercritical CO2 Gasification for Hydrogen Production

A bench-scale supercritical CO2 gasifier is being considered by the U.S. Department of Energy’s National Energy Technology Laboratory (NETL). A reacting computational fluid dynamics (CFD) model was developed using ANSYS/Fluent in order to investigate the impact of various operating parameters on syngas composition. The model was validated using available data in the literature. Simulations were conducted over a range of coal-slurry loadings, reaction temperatures, system pressures, and oxygen mass flowrates with the goal of optimizing hydrogen production for the considered reactor. The results from the simulations identified a positive correlation between slurry loading and hydrogen production, while reactor temperature and pressure had a limited impact on H2 production at the conditions of interest. Additionally, the simulations indicated that oxygen mass flowrate has less of an impact on hydrogen production at higher slurry loadings.

Prlina, Alexander↗
DOE OSTI2022

CO2U Example Report: NETL CO2 to Renewable Diesel and Co-products via Algal Production

This report represents an example of a completed project for the CO2 Utilization program. The LCA for this example corresponds to the example product systems in the NETL openLCA Life Cycle Inventory (LCI) database. This example LCA represents a fictional microalgae-to-biofuel, hereafter called algae-to-biofuel, technology pathway.

Krynock, Michelle↗
DOE OSTI2021

Radial Compressor Design and Off-Design for Trans-critical CO2 Operating Conditions

Presentation for the The 7th International Supercritical CO2 Power Cycles Symposium, February 21 – 24, 2022, San Antonio, Texas. A multi-staged intercooled centrifugal compressor design is performed for an indirect-fired sCO2 cycle and the design point data are used to generate the performance maps using a 2D mean-line analysis code. Fluid and turbomachinery similarity laws are applied to find an appropriate surrogate ideal gas fluid to be used in the design and performance map generation codes. The performance maps are then scaled back for the sCO2 fluid case using the affinity laws.

Uysal, Selcuk Can↗
DOE OSTI2022

Site Selection and Cost Estimation of Pilot-Scale CO2 Saline Storage Study in the Gulf of Mexico

Presentation at NETL Carbon Management Project Review Meeting held in Pittsburgh, Pennsylvania, August 15–19, 2022. The presentation provides a high-level overview of initial conceptual analysis evaluating site selection, geologic assessment, infrastructure, and project cost considerations associated with the development of pilot-scale CO2 storage projects in the offshore Gulf of Mexico.

Wijaya, Nur↗
DOE OSTI2022

Pathways to CO2 Utilization and Storage for the Intermountain West Region

The presentation, delivered at the 2022 Carbon Management Project Review Meeting held in Pittsburgh, PA (August 15 – 19, 2022), provides a detailed perspective on CO2 utilization and storage as a deep decarbonization pathway as it relates to states that make up the Intermountain West (I-WEST) region of the U.S. Content within shows findings from evaluation of the opportunity and potential value delivery that exists for CCUS to deploy at significant scale in the I-WEST region considering the region’s prominent enabling factors. This work is part of a larger initiative involving the development of a regional, stakeholder-informed technology “roadmap” for a sustainable and equitable transition to carbon neutral in the I-WEST.

Vikara, Derek↗
DOE OSTI2022

User Guide for the Public Industrial CO2 Capture Retrofit Database Models

OBSOLETE CCRD – SUPERSEDED<p>The National Energy Technology Laboratory (NETL) user manual accompanies the carbon capture retrofit database (CCRD) model that allows users to evaluate the cost of carbon capture on industrial sources (ammonia, cement, ethanol, hydrogen, and natural gas processing). The model was created by the National Energy Technology Laboratory (NETL) based on the technical report titled &quot;Cost of Capturing CO2 from Industrial Sources&quot; (NETL/DOE-2022/3319). Revised 12/21/22.</p>

Hughes, Sydney↗
DOE OSTI2022

Industrial CO2 Capture Retrofit Database (IND CCRD)

OBSOLETE CCRD - SUPERSEDED<p>This carbon capture retrofit database (CCRD) model allows users to evaluate the cost of carbon capture on industrial sources (ammonia, cement, ethanol, hydrogen, and natural gas processing). The model was created by the National Energy Technology Laboratory (NETL) based on the technical report titled Cost of Capturing CO2 from Industrial Sources (NETL/DOE-2022/3319). Revised 12/21/22.</p>

Hughes, Sydney↗