SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

All sources NASA NTRS DOE OSTI

NASA NTRS1960

Transonic Performance Characteristics of Several Jet Noise Suppressors

An investigation of the transonic performance characteristics of several noise-suppressor configurations has been conducted in the Langley 16-foot transonic tunnel. The models were tested statically and over a Mach number range from 0.70 to 1.05 at an angle of attack of 0 deg. The primary jet total-pressure ratio was varied from 1.0 (jet off) to about 4.5. The effect of secondary air flow on the performance of two of the configurations was investigated. A hydrogen peroxide turbojet-engine simulator was used to supply the hot-jet exhaust. An 8-lobe afterbody with centerbody, short shroud, and secondary air had the highest thrust-minus-drag coefficients of the six noise-suppressor configurations tested. The 12-tube and 12-lobe afterbodies had the lowest internal losses. The presence of an ejector shroud partially shields the external pressure distribution of the 8-lobe after-body from the influence of the primary jet. A ring-airfoil shroud increased the static thrust of the annular nozzle but generally decreased the thrust minus drag at transonic Mach numbers.

Schmeer, James W.↗

NASA NTRS1961

Experimental Investigation of a High-Speed Hydrofoil with Parabolic Thickness Distribution and an Aspect Ratio of 3

An experimental investigation has been made to determine the hydro-dynamic characteristics of a 10-percent-thick hydrofoil with an aspect ratio of 3 designed to operate with acceptable efficiency at speeds in the neighborhood of 100 knots (169 fps). A cambered hydrofoil model with parabolic thickness distribution was investigated at a depth of chord over a range of angles of attack from -0.5 deg to 4.0 deg and at speeds from 120 to 210 fps. substantially wider range of operation at acceptable lift-drag ratios as well as higher maximum lift-drag-ratio values than did a hydrofoil of similar design with an aspect ratio of 1.

Christopher, Kenneth W.↗

NASA NTRS2006

Analysis of Flow Angularity Repeatability Tests in the NTF

An extensive data base of flow angularity repeatability measurements from four NTF check standard model tests is analyzed for statistical consistency and to characterize the results for prediction of angle-of-attack uncertainty for customer tests. A procedure for quality assurance for flow angularity measurements during customer tests is also presented. The efficacy of the procedure is tested using results from a customer test.

Hemsch, Michael J.↗

NASA NTRS2011

USM3D Simulations of Saturn V Plume Induced Flow Separation

The NASA Constellation Program included the Ares V heavy lift cargo vehicle. During the design stage, engineers questioned if the Plume Induced Flow Separation (PIFS) that occurred along Saturn V rocket during moon missions at some flight conditions, would also plague the newly proposed rocket. Computational fluid dynamics (CFD) was offered as a tool for initiating the investigation of PIFS along the Ares V rocket. However, CFD best practice guidelines were not available for such an investigation. In an effort to establish a CFD process and define guidelines for Ares V powered simulations, the Saturn V vehicle was used because PIFS flight data existed. The ideal gas, computational flow solver USM3D was evaluated for its viability in computing PIFS along the Saturn V vehicle with F-1 engines firing. Solutions were computed at supersonic freestream conditions, zero degree angle of attack, zero degree sideslip, and at flight Reynolds numbers. The effects of solution sensitivity to grid refinement, turbulence models, and the engine boundary conditions on the predicted PIFS distance along the Saturn V were discussed and compared to flight data from the Apollo 11 mission AS-506.

Deere, Karen↗

NASA NTRS2015

Assessment of Slat Noise Predictions for 30P30N High-Lift Configuration From BANC-III Workshop

This paper presents a summary of the computational predictions and measurement data contributed to Category 7 of the 3rd AIAA Workshop on Benchmark Problems for Airframe Noise Computations (BANC-III), which was held in Atlanta, GA, on June 14-15, 2014. Category 7 represents the first slat-noise configuration to be investigated under the BANC series of workshops, namely, the 30P30N two-dimensional high-lift model (with a slat contour that was slightly modified to enable unsteady pressure measurements) at an angle of attack that is relevant to approach conditions. Originally developed for a CFD challenge workshop to assess computational fluid dynamics techniques for steady high-lift predictions, the 30P30N configurations has provided a valuable opportunity for the airframe noise community to collectively assess and advance the computational and experimental techniques for slat noise. The contributed solutions are compared with each other as well as with the initial measurements that became available just prior to the BANC-III Workshop. Specific features of a number of computational solutions on the finer grids compare reasonably well with the initial measurements from FSU and JAXA facilities and/or with each other. However, no single solution (or a subset of solutions) could be identified as clearly superior to the remaining solutions. Grid sensitivity studies presented by multiple BANC-III participants demonstrated a relatively consistent trend of reduced surface pressure fluctuations, higher levels of turbulent kinetic energy in the flow, and lower levels of both narrow band peaks and the broadband component of unsteady pressure spectra in the nearfield and farfield. The lessons learned from the BANC-III contributions have been used to identify improvements to the problem statement for future Category-7 investigations.

Choudhari, Meelan↗

NASA NTRS2017

CFD Study of NACA 0018 Airfoil with Flow Control

The abilities of two different Reynolds-Averaged Navier-Stokes codes to predict the effects of an active flow control device are evaluated. The flow control device consists of a blowing slot located on the upper surface of an NACA 0018 airfoil, near the leading edge. A second blowing slot present on the airfoil near mid-chord is not evaluated here. Experimental results from a wind tunnel test show that a slot blowing with high momentum coefficient will increase the lift of the airfoil (compared to no blowing) and delay flow separation. A slot with low momentum coefficient will decrease the lift and induce separation even at low angles of attack. Two codes, CFL3D and FUN3D, are used in two-dimensional computations along with several different turbulence models. Two of these produced reasonable results for this flow, when run fully turbulent. A more advanced transition model failed to predict reasonable results, but warrants further study using different inputs. Including inviscid upper and lower tunnel walls in the simulations was found to be important in obtaining pressure distributions and lift coefficients that best matched experimental data. A limited number of three-dimensional computations were also performed.

Eggert, Christopher A.↗

NASA NTRS2017

Simulation Propulsion System and Trajectory Optimization

A number of new aircraft concepts have recently been proposed which tightly couple the propulsion system design and operation with the overall vehicle design and performance characteristics. These concepts include propulsion technology such as boundary layer ingestion, hybrid electric propulsion systems, distributed propulsion systems and variable cycle engines. Initial studies examining these concepts have typically used a traditional decoupled approach to aircraft design where the aerodynamics and propulsion designs are done a-priori and tabular data is used to provide inexpensive look ups to the trajectory ana-ysis. However the cost of generating the tabular data begins to grow exponentially when newer aircraft concepts require consideration of additional operational parameters such as multiple throttle settings, angle-of-attack effects on the propulsion system, or propulsion throttle setting effects on aerodynamics. This paper proposes a new modeling approach that eliminated the need to generate tabular data, instead allowing an expensive propulsion or aerodynamic analysis to be directly integrated into the trajectory analysis model and the entire design problem optimized in a fully coupled manner. The new method is demonstrated by implementing a canonical optimal control problem, the F-4 minimum time-to-climb trajectory optimization using three relatively new analysis tools: Open M-DAO, PyCycle and Pointer. Pycycle and Pointer both provide analytic derivatives and Open MDAO enables the two tools to be combined into a coupled model that can be run in an efficient parallel manner that helps to cost the increased cost of the more expensive propulsion analysis. Results generated with this model serve as a validation of the tightly coupled design method and guide future studies to examine aircraft concepts with more complex operational dependencies for the aerodynamic and propulsion models.

Optimization↗

NASA NTRS2019

Computational Analysis of the External Aerodynamics of the Unpowered X-57 Mod-III Aircraft

Investigations of the external aerodynamics of the unpowered X-57 Mod-III configuration using computational fluid dynamics are presented. Two different Reynolds-averaged Navier-Stokes flow solvers were used in the analysis: the STAR-CCM+ unstructured solver using polyhedral grid topology, and the Launch Ascent Vehicle Aerodynamics (LAVA) structured curvilinear flow solver using structured overset grid topology. A grid refinement study was conducted and suitable grid resolution was determined by examining the forces and moments of the aircraft. Code-to-code comparison shows that STAR-CCM+ and LAVA are in good agreement both in quantitative values and trends. The angle-of-attack sweep and sideslip-angle sweep were performed. Results indicate that lift coefficients have a sharp drop at stall. At high angle of attack, STAR-CCM+ and LAVA show different flow separation behavior possibly due to differences in the turbulence model. The sideslip-angle sweep results show constant pitching moment from 0° to 15°, then a sharp increase between 15° and 20° sideslip angle.

Yoo, Seung Y.↗

NASA NTRS2022

An Analysis of the Impact of Extreme Attitude Operation on a Turbofan Engine in a Regional Jet Aircraft

The objective of this work is to characterize the variability in engine performance at extreme attitudes, resulting from the use of different standard control variables, evaluated at different points in the engine’s lifecycle. This paper describes the procedure used to create a dynamic model of an aft-mounted jet engine on a T-tail regional jet aircraft. This model enables simulation of engine operation at extreme attitudes. The model was subsequently evaluated at various altitudes, Mach numbers, and power settings over a range of angles of attack and sideslip, and deterioration levels. Each case was simulated using both fan speed and engine pressure ratio as the engine control variable. The results show that the wing has a very large impact on the engine operation, overwhelming other sources of variation.

loss of control - inflight↗

NASA NTRSDate not supplied

Transonic Limit Cycle Oscillations of the Benchmark Supercritical Wing

This paper considers transonic flutter mechanisms of the Benchmark Supercritical Wing, a model under study in the Aeroelastic Prediction Workshop series. Flutter boundaries are mapped out across an angle of attack sweep at Mach 0.8, utilizing both time-domain and linearized frequency-domain solvers, manual meshes and adapted meshes, and various governing equations. With increased angle of attack, linearized and finite amplitude flutter predictions exhibit differences above 3◦ as the flow begins to separate; the latter predictions are found to be driven by subcritical limit cycle oscillations whose strength increases with angle of attack. Moderate perturbation values provide a stability boundary at 5◦ which matches the experimental data, but it is not clear how the experimental perturbation, from one test condition to the next, can be reasonably characterized.

Bret Stanford↗

NASA NTRSDate not supplied

Evaluation of Wall-Modeled Les for Flow Over A Multi-Element Airfoil

We perform wall-modeled large-eddy simulations (WMLES) of turbulent flow over a 30P30N multielement airfoil at various angles of attack to assess its ability to accurately predict lift using an unstructured node-based finite-volume methodology. The flow conditions are based on the experiments reported in Klausmeyer & Lin [NASA /TM-112858]. The oncoming flow Mach number is 0.2, and the stowed chord-based Reynolds number (𝑅𝑒𝑐) is 9 million. The angle of attack (𝛼) is varied between 8◦ and 23◦ with the expected stall angle of around 21◦. The simulated geometry is periodic in the span, thus any three-dimensional effects present in the experiment are ignored. We first analyze the predictions with baseline isotropic and anisotropic grids containing over 16 grid points per boundary-layer thickness. The near-wall streamwise/nominal spacing ratio is 0.4 at the leading/trailing edges of the slat, main element and flap, and 1 elsewhere, and the first wall-normal/nominal spacing ratio is 0.375 over most of the airfoil for the anisotropic grid, while these are unity for the isotropic grid. It is found that the predicted lift and wall pressures, near-wall velocity profiles, and the location of onset of resolved turbulence are sensitive to the near-wall grid anisotropy. Further sensitivities were explored at lower angles of attack by independently varying the streamwise and wall-normal grid anisotropies. The effects of both off-wall and near-wall grid refinement were also quantified. For the grid resolutions used here, our results suggest that the first wall-normal spacing, which coincides with the WMLES exchange location, has a dominant effect on the predictions for this flow configuration.

Computational Fluid Dynamics↗

NASA NTRSDate not supplied

Application of PSP on the SWiFT Model in the National Transonic Facility

This report details the results from a Pressure Sensitive Paint test on a blended/hybrid wing body model conducted at the National Transonic Facility. This test investigated potential instabilities that can occur at high Reynolds number and low Mach number testing conditions. The upper surface of the model was coated with pressure sensitive paint, and data was collected at various Mach numbers and angles of attack. For this test, typical pitch-pause testing was completed as well as a novel continuous sweep functionality that provided much greater angle of attack resolution. Results from this test will be presented, including indications of potential instability points in the testing envelope.

NTF↗

DOE OSTI2024

Security of quantum position-verification limits Hamiltonian simulation via holography

We investigate the link between quantum position-verification (QPV) and holography established in [1] using holographic quantum error correcting codes as toy models. By inserting the “temporal” scaling of the AdS metric by hand via the bulk Hamiltonian interaction strength, we recover a toy model with consistent causality structure. This leads to an interesting implication between two topics in quantum information: if position-based verification is secure against attacks with small entanglement then there are new fundamental lower bounds for resources required for one Hamiltonian to simulate another.

AdS-CFT Correspondence↗

NASA NTRS2012

Acoustic Surveys of a Scaled-Model CESTOL Transport Aircraft in Static and Forward Speed Conditions

An 11% scale-model of a Cruise-Efficient Short Take-off and Landing (CESTOL) scalemodel test was recently completed. The test was conducted in the AEDC National Full-Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. The model included two over-wing pod-mounted turbine propulsion simulators (TPS). The hybrid blended wing-body used a circulation control wing (CCW) with leadingand trailing-edge blowing. The bulk of the test matrix included three forward velocities (40 kts, 60 kts, and 100kts), angle-of-attack variation between -5 and 25 , and CCW mass flow variation. Seven strut-mounted microphones outboard of the left wing provided source directivity. A phased microphone array was mounted outboard of the right wing for source location. The goal of this paper is to provide a preliminary look at the acoustic data acquired during the Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) test for 0 angle-of-attack and 0 sideslip conditions. Data presented provides a good overview of the test conditions and the signal-to-noise quality of the data. TPS height variation showed a difference of 2 dB to 3 dB due to wing shielding. Variation of slot mass flow showed increases of 12 dB to 26 dB above the airframe noise and the TPS increased the overall levels an additional 5 dB to 10 dB.

Burnside, Nathan↗

NASA NTRS1989

Unsteady blade pressure measurements on a model counterrotation propeller

In an exploratory effort an advanced counterrotation propeller instrumented with blade-mounted pressure transducers was tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel at a simulated takeoff and landing speed of Mach 0.20. The propeller's aft diameter was reduced to investigate possible noise reductions resulting from reduced blade row interaction with the tip vortex. The propeller was tested at three blade row spacings at fixed blade setting angles, at the maximum blade row spacing at higher blade setting angles and at propeller axis angles attack to the flow up to + or - 16 deg. A limited number of unsteady blade surface pressure measurements were made on both rotors of the model counterrotation propeller. Emphasis was placed on determining the effects of rotor-rotor interactions on the blade surface pressures. A unique method of processing the pressure signals was developed that enables even weak interaction waveforms and spectra to be separated from the total signal. The interaction on the aft rotor was many times stronger than that on the forward rotor. The fundamental rotor interaction tone exhibited complicated behavior but generally increased with rotational speed and blade setting angle and decreased with rotor spacing. With the propeller axis at an angle to the flow, the phase response of the aft rotor appeared to be significantly affected by the presence of the forward rotor.

Heidelberg, Laurence J.↗

NASA NTRS1989

Unsteady blade pressure measurements on a model counterrotation propeller

Heidelberg, Laurence J.↗

NASA NTRS1981

Viscous-inviscid interaction method including wake effects for three-dimensional wing-body configurations

A viscous-inviscid interaction method has been developed by using a three-dimensional integral boundary-layer method which produces results in good agreement with a finite-difference method in a fraction of the computer time. The integral method is stable and robust and incorporates a model for computation in a small region of streamwise separation. A locally two-dimensional wake model, accounting for thickness and curvature effects, is also included in the interaction procedure. Computation time spent in converging an interacted result is, many times, only slightly greater than that required to converge an inviscid calculation. Results are shown from the interaction method, run at experimental angle of attack, Reynolds number, and Mach number, on a wing-body test case for which viscous effects are large. Agreement with experiment is good; in particular, the present wake model improves prediction of the spanwise lift distribution and lower surface cove pressure.

Streett, C. L.↗

DOE OSTI2022

Broken-Symmetry Density Functional Theory Analysis of the Ω Intermediate in Radical S -Adenosyl- l -methionine Enzymes: Evidence for a Near-Attack Conformer over an Organometallic Species

Radical S-adenosyl-L-methionine (SAM) enzymes are found in all domains of life and catalyze a wide range of biochemical reactions. Recently, an organometallic intermediate, Ω, has been experimentally implicated in the 5'-deoxyadenosyl radical generation mechanism of the radical SAM superfamily. In this work, we employ broken-symmetry density functional theory to evaluate several structural models of Ω. The results show that the calculated hyperfine coupling constants (HFCCs) for the proposed organometallic structure of Ω are inconsistent with the experiment. In contrast, a near-attack conformer of SAM bound to the catalytic [4Fe–4S] cluster, in which the distance between the unique iron and SAM sulfur is ~3 Å, yields HFCCs that are all within 1 MHz of the experimental values. Furthermore, these results clarify the structure of the ubiquitous Ω intermediate and suggest a paradigm shift reversal regarding the mechanism of SAM cleavage by members of the radical SAM superfamily.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗