Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Internship Presentation: Integrating Safety and Cybersecurity: Security-by-Design with SOWT Analysis for Reactor Testing

This study covers leveraging reactor testing facilities that are primarily designed with a focus on safety to enhance cybersecurity testing. By incorporating reactor security-by-design with reactor safety-by-design principles and adopting defense-in-depth strategies that emphasize both safety and security, the research evaluates applicable cyber tools, models, and solutions. This includes simulating specific cyber-attack scenarios using reactor simulators and performing SWOT (Strengths, Weaknesses, Opportunities, Threats) analysis to improve the cybersecurity of reactor systems.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗
DOE OSTI2026

Combined-Accelerated Stress Testing of Photovoltaic Materials

By applying multiple environmental stresses in fieldrepresentative combinations and sequences, combined-accelerated stress testing (CAST) identifies degradation modes and failure mechanisms of photovoltaic (PV) modules and components that are missed by single stress factor accelerated testing.

14 SOLAR ENERGY↗
DOE OSTI2022

Chapter 8: Life-Cycle Testing and Analysis

Prior to a spacecraft launch, program mission assurance standards dictate that the flight battery power system should comply with mission requirements under the intended operating conditions. Ground life cycle testing (LCT) combined with an analysis on the electrical power system (EPS) battery is an empirical method used to demonstrate compliance to satellite service life requirements. The LCT compliance method adopted by the aerospace industry is based on demonstrating a space battery's life expectancy as a part of battery qualification. Real-time cell and lithium-ion battery (LIB) LCT data are commonly used for model inputs to EPS power and energy balance analyses, in LIB reliability analysis estimates, and to support on-orbit spacecraft mission life extension opportunities. This chapter describes the LCT planning steps, process approach, and analysis techniques commonly used to qualify space LIB power systems.

accelerated aging↗
DOE OSTI2022

Utah FORGE: Well 16A(78)-32 Stimulation Tracer Test Results

This archive contains data from the tracer test performed during the Utah FORGE well 16A(78)-32 stimulation. This includes: 1. the raw data file from Pason in the csv format; 2. a one-page Word document from Pason that explains the headers and units used in their data file; 3. an Excel spreadsheet with concentration data and relevant Pason flow data; 4. a Word document with jpg versions of concentration charts (Figs. 1-3) and a tracer mass recovery chart (Fig. 4).

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

Lithium-Ion Battery Testing Capable of Simulating “Ultralow” Lunar Temperatures

The first-ever lithium-ion battery cycler capable of testing the coin and pouch cells under ultralow (≤40 °C) temperatures down to -175 °C to simulate extreme climates found in the lunar and space missions, high-altitude air vehicles, polar regions of Earth, and military expeditionary missions is enthusiastically reported. The extremely cold temperatures are achieved through a tailored extreme low-temperature system (ELTS) with liquid nitrogen flow and the ability to reach temperatures between -175 and 25 °C, using 1 kΩ and 1 MΩ resistors at varying currents of 1–4 mA and 1–4 μA, respectively, is validated. Employing the ELTS, Li 4 Ti 5 O 12 (LTO)||Li cells with 1 m lithium bis(fluorosulfonyl)imide in cyclopentyl methyl ether as an electrolyte developed in this research group are charged and discharged at room temperature (cycling rate C/5), -20 (C/10), -40 (C/40), and -60 °C (C/50), which exhibited discharge capacities of 159.04, 119.12, 101.79, and 33.06 mAh g -1 , respectively. Moreover, the LTO||Li cell produced a reversible capacity of 7.12 mAh g -1 tested at -100 °C for the first time.

25 ENERGY STORAGE↗
DOE OSTI2024

Comparative Analyses of Bioequivalence Assessment Methods for In Vitro Permeation Test Data

ABSTRACT For topical, dermatological drug products, an in vitro option to determine bioequivalence (BE) between test and reference products is recommended. In particular, in vitro permeation test (IVPT) data analysis uses a reference‐scaled approach for two primary endpoints, cumulative penetration amount (AMT) and maximum flux ( J max ), which takes the within donor variability into consideration. In 2022, the Food and Drug Administration (FDA) published a draft IVPT guidance that includes statistical analysis methods for both balanced and unbalanced cases of IVPT study data. This work presents a comprehensive evaluation of various methodologies used to estimate critical parameters essential in assessing BE. Specifically, we investigate the performance of the FDA draft IVPT guidance approach alongside alternative empirical and model‐based methods utilizing mixed‐effects models. Our analyses include both simulated scenarios and real‐world studies. In simulated scenarios, empirical formulas consistently demonstrate robustness in approximating the true model, particularly in effectively addressing treatment–donor interactions. Conversely, the effectiveness of model‐based approaches heavily relies on precise model selection, which significantly influences their results. The research emphasizes the importance of accurate model selection in model‐based BE assessment methodologies. It sheds light on the advantages of empirical formulas, highlighting their reliability compared to model‐based approaches and offers valuable implications for BE assessments. Our findings underscore the significance of robust methodologies and provide essential insights to advance their understanding and application in the assessment of BE, employed in IVPT data analysis.

Leon, Sami↗
DOE OSTI2024

The use of idealised experiments in testing a new convective parametrization: Performance of CoMorph-A

CoMorph is a new mass-flux convection parametrization under development at the Met Office designed for use within the Unified Model and its successor model, LFRic. Use of a three-dimensional idealised model enables controlled tests of the performance of the scheme across different regimes. This includes the interaction between the physical parametrizations and the resolved dynamics, allowing study of the emergent organisation of convection on the resolved scale. A selection of well-known cases is revisited here, with the purpose of documenting the extent to which CoMorph captures a range of important, but challenging, behaviour such as the diurnal cycle and sensitivity to tropospheric moisture. Simulations using CoMorph-A, a new physics package, that has been demonstrated to perform well at numerical weather prediction (NWP) and climate scales, are compared against the current global atmosphere configuration and high-resolution results. In addition to an entirely new convection scheme, the package of changes includes significant changes to the cloud, microphysics, and boundary-layer parametrizations. Recognising that CoMorph-A is the first version of a scheme that will continue to be substantially developed and to obtain good performance, compromises in tuning have had to be made. These idealised tests therefore show what works well in this configuration, and what areas will require further work. As such, it is quite a demanding testbed and could be viewed as some of the equipment required for a “convective playground”.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Squeeze Film Damper Experimental and Numerical Correlation: Test Setup Description and Parameter Identification of Dry System

The process of characterizing a damper involves both experimental techniques and model simulation. Experiments characterize dynamic behavior of a system through empirical modal analysis using impact and shaker testing. The layout of the test setup is crucial for a low-mass, nonlinear system. Physical arrangement, orientation of the system, and instrumentation affect the results that are discussed in this paper. These results can be used to validate a numerical simulation of the same system. With a validated model, important physical input parameters and modeling techniques can be determined and implemented in future designs. In other words, this modeling can be used with confidence to design alternative dampers that may be difficult, costly, and time-consuming to characterize experimentally.

Cook, Jason↗
DOE OSTI2025

Testing the lepton content of the proton at HERA and EIC

Although protons are baryons with an overall vanishing lepton number, they possess a non-trivial leptonic content arising from quantum fluctuations which can be described by lepton parton distribution functions (PDFs) of the proton. These PDFs have been recently computed and can be used to define lepton-induced processes at high-energy colliders. In this article, we propose a novel way to test the computation of lepton PDFs of the proton by analyzing both non-resonant di-lepton and resonant Z gauge boson production processes induced by leptons within the proton at proton-electron colliders like HERA and EIC. Despite the fact that lepton PDFs of the proton are known to be small, this work demonstrates that both processes imply a measurable yield of events at HERA and EIC, which could be used to test these PDFs.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

A precision test of averaging in AdS/CFT

We reconsider the role of wormholes in the AdS/CFT correspondence. We focus on Euclidean wormholes that connect two asymptotically AdS or hyperbolic regions with $\mathbb{S}$ 1 × $\mathbb{S}$ d-1 boundary. There is no solution to Einstein’s equations of this sort, as the wormholes possess a modulus that runs to infinity. To find on-shell wormholes we must stabilize this modulus, which we can do by fixing the total energy on the two boundaries. Such a wormhole gives the saddle point approximation to a non-standard problem in quantum gravity, where we fix two asymptotic boundaries and constrain the common energy. Crucially the dual quantity does not factorize even when the bulk is dual to a single CFT, on account of the fixed energy constraint. From this quantity we extract a smeared version of the microcanonical spectral form factor. For a chaotic theory this quantity is self-averaging, i.e. well-approximated by averaging over energy windows, or over coupling constants. We go on to give a precision test involving the microcanonical spectral form factor where the two replicas have slightly different coupling constants. In chaotic theories this form factor is known to smoothly decay at a rate universally predicted in terms of one replica physics, provided that there is an average either over a window or over couplings. We compute the expected decay rate for holographic theories, and the form factor from a wormhole, and the two exactly agree for a wide range of two-derivative effective field theories in AdS. This gives a precision test of averaging in AdS/CFT. Our results interpret a number of confusing facts about wormholes and factorization in AdS and suggest that we should regard gravitational effective field theory as a mesoscopic description, analogous to semiclassical mesoscopic descriptions of quantum chaotic systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Thermo-Hydro-Mechanical Modeling of Brine Migration in a Heated Borehole Test in Bedded Salt

Abstract This research paper focuses on the thermo-hydro-mechanical (THM) modeling of brine migration in a heated borehole test conducted as part of the ongoing Brine Availability Test in Salt (BATS) at the Waste Isolation Pilot Plant (WIPP) in New Mexico. It is a component of the international collaboration project DECOVALEX-2023 (DEvelopment of COupled models and their VALidation against EXperiments), which aims to understand the THM processes governing brine flow in heated rock salt repositories through collaborative analysis by multiple research teams. Using the TOUGH–FLAC simulator, THM simulations were performed and compared with data from the BATS phase 1a. This experiment involved two identical horizontal-borehole arrays, one heated and one serving as a control, both equipped with sensor arrays. Analysis of measurements revealed water flow rate surges during heater power transitions, with the highest jump observed during cooling. Acoustic emission activity exhibited distinct patterns in response to heater power changes, suggesting that damage to rock salt is particularly pronounced during the cooling phase. The THM simulations successfully captured these phenomena, highlighting the significance of thermal effects, brine migration, and mechanical behavior in predicting brine availability in heated and damaged rock salt. Our modeling also revealed the critical interplay between heating and cooling-induced damage and its influence on flow properties, particularly affecting brine inflow estimation. Notably, we found that cooling-induced brine inflow spikes result from increased permeability due to tensile dilatancy. These findings have important implications for the development of robust containment strategies and enhance our understanding of the complex processes involved in repository performance.

58 GEOSCIENCES↗
DOE OSTI2020

An Overview of the Hybrid Illinois Device for Research and Applications Material Analysis Test-stand (HIDRA-MAT)

The Hybrid Illinois Device for Research and Applications (HIDRA) at the University of Illinois at Urbana-Champaign is a toroidal plasma device that enables fusion plasma-material interaction testing with both stellarator and tokamak plasmas. HIDRA’s long-pulse steady state stellarator plasmas provide a testbed for plasma facing component (PFC) plasma exposures. The HIDRA Material Analysis Test-stand (HIDRA-MAT) is a material characterization module attached to HIDRA that is being designed and fabricated to include thermal desorption spectroscopy and laser induced breakdown spectroscopy systems for in-vacuo PFC characterization. A specialized rotatable sample holder positions the sample for liquid metal droplet application from a liquid metal droplet injector on HIDRA-MAT. Early experiments look to investigate the effect liquid lithium has on porous tungsten samples’ retention of H, D, and He after plasma exposure. Preliminary results from a dual residual gas analyzer system show the ability to differentiate D2 and He in HIDRA-MAT. Finally, this work aims to advance the understanding of liquid metal PFCs and further the design and development of new fusion PFCs and technologies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Irradiation Tests of Superconducting Detectors and Comparison with Simulations

For the future satellite mission at the second sun–earth Lagrangian point (L2), we need to mitigate phonon propagation created by cosmic rays to superconducting detectors. We simulate phonon propagation in silicon substrate and show that putting a metal layer on the substrate or making hole in the substrate reduces the propagation. We also show a function which shows the response of a TES bolometer on a substrate. To validate these theoretical expectations, we make irradiation tests using two types of superconducting detectors: transition edge sensor bolometers and kinetic inductance detectors. From the tests, we show that putting metal can reduce correlations between detectors and number of hit events from charged particles.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

The SuperCam Instrument Suite on the NASA Mars 2020 Rover: Body Unit and Combined System Tests

The SuperCam instrument suite provides the Mars 2020 rover, Perseverance, with a number of versatile remote-sensing techniques that can be used at long distance as well as within the robotic-arm workspace. These include laser-induced breakdown spectroscopy (LIBS), remote time-resolved Raman and luminescence spectroscopies, and visible and infrared (VISIR; separately referred to as VIS and IR) reflectance spectroscopy. A remote micro-imager (RMI) provides high-resolution color context imaging, and a microphone can be used as a stand-alone tool for environmental studies or to determine physical properties of rocks and soils from shock waves of laser-produced plasmas. SuperCam is built in three parts: The mast unit (MU), consisting of the laser, telescope, RMI, IR spectrometer, and associated electronics, is described in a companion paper. The on-board calibration targets are described in another companion paper. Here we describe SuperCam’s body unit (BU) and testing of the integrated instrument. The BU, mounted inside the rover body, receives light from the MU via a 5.8 m optical fiber. The light is split into three wavelength bands by a demultiplexer, and is routed via fiber bundles to three optical spectrometers, two of which (UV and violet; 245–340 and 385–465 nm) are crossed Czerny-Turner reflection spectrometers, nearly identical to their counterparts on ChemCam. The third is a high-efficiency transmission spectrometer containing an optical intensifier capable of gating exposures to 100 ns or longer, with variable delay times relative to the laser pulse. This spectrometer covers 535–853 nm ( $105\text{--}7070~\text{cm}^{-1}$ Raman shift relative to the 532 nm green laser beam) with $12~\text{cm}^{-1}$ full-width at half-maximum peak resolution in the Raman fingerprint region. The BU electronics boards interface with the rover and control the instrument, returning data to the rover. Thermal systems maintain a warm temperature during cruise to Mars to avoid contamination on the optics, and cool the detectors during operations on Mars.Results obtained with the integrated instrument demonstrate its capabilities for LIBS, for which a library of 332 standards was developed. Examples of Raman and VISIR spectroscopy are shown, demonstrating clear mineral identification with both techniques. Luminescence spectra demonstrate the utility of having both spectral and temporal dimensions. Finally, RMI and microphone tests on the rover demonstrate the capabilities of these subsystems as well.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

High Speed Impact Testing of UHMWPE Composite Using Orthogonal Arrays

Abstract Background Ultra high molecular weight polyethylene composites are fiber based composites used in armor applications. While some characterization has been conducted experimentally, this study varies multiple parameters simultaneously to investigate material response under a wide range of conditions. Objective This work focuses on characterizing the response of Dyneema ® HB26 hard laminate composites under high-speed impacts to examine the influence of plate diameter, clamping pressure, and plate spacing on target performance. Additionally, micro Computer Tomography scans are used to nondestructively evaluate the damage evolution in the targets. Methods These scan results are used in concert with more traditional armor performance metrics to evaluate the effect of various parameters using the method of orthogonal array analysis. This technique allows for multiple variables to be investigated in the same test series, saving time and budget while still providing quality results across a range of variables and variable values. Results We conclude that of the parameters investigated, the plate spacing parameter has the largest effect on performance, followed by the plate diameter. Bolt torque was found to not have a significant impact on results, indicating that an edge clamping pressure is not critical to material response. Additionally, by examining the high resolution scans, we can quantify the damage with an effective damage angle and that this angle is a good predictor of performance. Conclusion Finally a damage theory involving the effective bending strength of the plates is discussed as an explanation for all of the results observed in this test series.

Hannah, T. (ORCID:0000000230261362)↗
DOE OSTI2024

Theory, analysis, and testing of an angular resonator for wave energy generation

This article describes the theory, analysis, and initial bench-top testing of a minimally invasive, rotational resonator designed to produce small amounts of electrical energy for use in oceanic observation buoys. Here, this work details the systems of equations that govern such a resonator, its potential power production, and its predicted effects on the modified motion of the buoy. Finally, a bench-top test apparatus is designed and experimented upon to identify the system and verify the system of equations empirically.

16 TIDAL AND WAVE POWER↗
DOE OSTI2024

Effects of size, geometry, and testing temperature on additively manufactured Ti-6Al-4V titanium alloy

This article presents a comprehensive study concerning size and geometry effect on the ambient and high-temperature mechanical behavior of additively manufactured laser powder bed fusion Ti-6Al-4V alloy. Key mechanical property metrics are presented, including strain hardening rate, yield strength, and Young’s modulus as a function of thickness and testing temperature (ambient, 250 °C, and 450 °C). Here, the effect of specimen size on manufacturing-induced microstructural feature formation is demonstrated and discussed. A detailed analysis regarding Young’s modulus, yield strength, and strain hardening rate variation at elevated temperatures is also presented. Size effect and temperature-sensitive deformation mechanisms are linked to the underlying microstructural deformation mechanisms activated at respective temperatures. Counter-intuitively, this study determined that irrespective of the geometry, strain hardening rates increased as temperature increased. An in-depth microstructural examination is presented to explain the stated observation. The texture of Interrupted tensile test samples examined for ambient, 250 °C, and 450 °C post-yield was observed to be unchanged, indicating the strain hardening behavior was not texture dependent. Schmid factor analysis, coupled with experimental findings from previous work, was implemented to generate a hypothesis. This hypothesis suggests that the drop in critical resolved shear stress for basal and pyramidal slip systems, as temperature increases, paired with the high dislocation density of laser powder bed fusion Ti-6Al-4V, leads to dislocation entanglement and results in increased strain hardening at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Testing of fiber optic based sensors for advanced reactors in the Texas A&M University TRIGA reactor

An Optical Fiber Based Gamma Thermometer has been developed and tested at the Texas A&M University reactor as well as the Ohio State Research Reactor. This sensor technology provides temperature measurement of a thermal mass undergoing gamma heating, from which the gamma flux along the length of the sensor may be calculated. The gamma flux data from an array of OFBGTs could allow the determination of local power density within a nuclear reactor core in three dimensions. The design of the sensor makes use of optical fiber as a truly distributed temperature sensor with a spatial resolution less than 1mm and temperature accuracy of ±1°C. The testing program showed that the system provided the expected temperature data for each location. Overall, this sensor technology shows promise for current Light Water Reactors as well as advanced nuclear reactors by providing an unparalleled level of precision in reactor power measurement.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗