Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SEA LEVEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

GOASEX observations of Seasat SAR cross-section modulation from surface winds

L-band data from the Seasat SAR and scatterometer are compared with three SAR data sets from the Gulf of Alaska Seasat Experiment to determine the effectiveness of the L-band for determining surface wind speeds. The SAR scans a 100 km swath several hundred km long. Cross sections from the SAR data were measured at the center, and were found to rise and fall with the observed sea level wind speeds. The L-band backscatter was found to be proportional to the square root of the surface winds, with upwind/crosswind differences as large as 10%. Concerted use of the SAR imagery and the scatterometer data are concluded to offer a capability of accurately describing windspeeds in a 25 x 25 km cell down to a 25 x 25 sq m cell. Implementation is noted to depend on further studies for comparisons of upper and lower air wind data.

Thompson, T. W.↗

Experimental study of external fuel vaporization

The fuel properties used in the design of a flash vaporization system for aircraft gas turbine engines were evaluated in experiments using a flowing system to determine critical temperature and pressure, boiling points, dew points, heat transfer coefficients, deposit formation rates, and deposit removal. Three fuels were included in the experiments: Jet-A, an experimental referree broad specification fuel, and a premium No. 2 diesel fuel. Engine conditions representing a NASA Energy Efficient Engine at sea-level take-off, cruise, and idle were simulated in the vaporization system and it was found that single phase flow was maintained in the heat exchanger and downstream of the throttle. Deposits encountered in the heat exchanger represented a thermal resistance as high as 1300 sq M K/watt and a deposit formation rate over 1000 gC/sq cm hr.

Szetela, E. J.↗

A diurnal resonance in the ocean tide and in the earth's load response due to the resonant free 'core nutation'

The effects of the oceans, which are subject to a resonance due to a free rotational eigenmode of an elliptical, rotating earth with a fluid outer core having an eigenfrequency of (1 + 1/460) cycle/day, on the body tide and nutational response of the earth to the diurnal luni-tidal force are computed. The response of an elastic, rotating, elliptical, oceanless earth with a fluid outer core to a given load distribution on its surface is first considered, and the tidal sea level height for equilibrium and nonequilibrium oceans is examined. Computations of the effects of equilibrium and nonequilibrium oceans on the nutational and deformational responses of the earth are then presented which show small but significant perturbations to the retrograde 18.6-year and prograde six-month nutations, and more important effects on the earth body tide, which is also resonant at the free core notation eigenfrequency.

Wahr, J. M.↗

Effect of broad properties fuel on injector performance in a reverse flow combustor

The effect of fuel type on the performance of various fuel injectors was investigated in a reverse flow combustor. Combustor performance and emissions are documented for simplex pressure atomizing, spill flow, and airblast fuel injectors using a broad properties fuel and compared with performance using Jet A fuel. Test conditions simulated a range of flight conditions including sea level take off, low and high altitude cruise, as well as a parametric evaluation of the effect of increased combustor loading. The baseline simplex injector produced higher emission levels with corresponding lower combustion efficiency with the broad properties fuel. There was little or not loss in performance by the two advanced concept injectors with the broad properties fuel. The airblast injector proved to be especially insensitive to fuel type.

Raddlebaugh, S. M.↗

Feasibility of water injection into the turbine coolant to permit gas turbine contingency power for helicopter application

A system which would allow a substantially increased output from a turboshaft engine for brief periods in emergency situations with little or no loss of turbine stress rupture life is proposed and studied analytically. The increased engine output is obtained by overtemperaturing the turbine; however, the temperature of the compressor bleed air used for hot section cooling is lowered by injecting and evaporating water. This decrease in cooling air temperature can offset the effect of increased gas temperature and increased shaft speed and thus keep turbine blade stress rupture life constant. The analysis utilized the NASA-Navy-Engine-Program or NNEP computer code to model the turboshaft engine in both design and off-design modes. This report is concerned with the effect of the proposed method of power augmentation on the engine cycle and turbine components. A simple cycle turboshaft engine with a 16:1 pressure ratio and a 1533 K (2760 R) turbine inlet temperature operating at sea level static conditions was studied to determine the possible power increase and the effect on turbine stress rupture life that could be expected using the proposed emergency cooling scheme. The analysis showed a 54 percent increse in output power can be achieved with no loss in gas generator turbine stress rupture life. A 231 K (415 F) rise in turbine inlet temperature is required for this level of augmentation. The required water flow rate was found to be .0109 kg water per kg of engine air flow.

Vanfossen, G. J.↗

Flight evaluation of an engine static pressure noseprobe in an F-15 airplane

The flight testing of an inlet static pressure probe and instrumented inlet case produced results consistent with sea-level and altitude stand testing. The F-15 flight test verified the basic relationship of total to static pressure ratio versus corrected airflow and automatic distortion downmatch with the engine pressure ratio control mode. Additionally, the backup control inlet case statics demonstrated sufficient accuracy for backup control fuel flow scheduling, and the station 6 manifolded production probe was in agreement with the flight test station 6 tota pressure probes.

Foote, C. H.↗

Energy efficient engine sector combustor rig test program

Under the NASA-sponsored Energy Efficient Engine program, Pratt & Whitney Aircraft has successfully completed a comprehensive combustor rig test using a 90-degree sector of an advanced two-stage combustor with a segmented liner. Initial testing utilized a combustor with a conventional louvered liner and demonstrated that the Energy Efficient Engine two-stage combustor configuration is a viable system for controlling exhaust emissions, with the capability to meet all aerothermal performance goals. Goals for both carbon monoxide and unburned hydrocarbons were surpassed and the goal for oxides of nitrogen was closely approached. In another series of tests, an advanced segmented liner configuration with a unique counter-parallel FINWALL cooling system was evaluated at engine sea level takeoff pressure and temperature levels. These tests verified the structural integrity of this liner design. Overall, the results from the program have provided a high level of confidence to proceed with the scheduled Combustor Component Rig Test Program.

Dubiel, D. J.↗

Liquid fluorine/hydrazine rhenium thruster update

The status of a fluorine/hydrazine thruster development program is discussed. A solid rhenium metal sea-level thrust chamber was successfully fabricated and tested for a total run duration of 1075 s with 17 starts. Rhenium fabrication methods are discussed. A test program was conducted to evaluate performance and chamber cooling. Acceptable performance was reached and cooling was adequate. A flight-type injector was fabricated that achieved an average extrapolated performance value of 3608 N-s/kg (368 lbf-s/lbm). Altitude thrust chambers were fabricated. One chamber incorporates a rhenium combustor and nozzle with an area ratio of 15:1, and a columbium nozzle extension with area ratios from 15:1 to 60:1. The other chamber was fabricated completely with a carbon/carbon composite. Because of the attributes of rhenium for use in high-temperature applications, a program to provide the materials and processes technology needed to reliably fabricate and/or repair vapor-deposited rhenium parts of relatively large size and complex shape is recommended.

Appel, M. A.↗

Atmospheric Effects

The Earth's atmosphere consists mostly of the dry components oxygen (about 21% by volume), nitrogen (about 78% by volume) argon (about 1% by volume), and wet components (water vapor, clouds and rain). Water vapor at 100% relative humidity is approximately 1.7% by volume assuming the U.S. Standard Atmosphere, 15 C, at sea level. A communications link through the atmosphere suffers attenuation from both the dry and wet components. This results in a decreased signal to noise ratio (SNR) of the communications link due to both the signal attenuation and the increased noise temperature resulting from thermal emission.

Stelzried, C. T.↗

A time-dependent ice sheet model - Preliminary results

A numerical model of ice sheet flow is developed, and preliminary results are described. This model includes vertical resolution of temperature, stress, and strain rate which represents a considerable improvement over previous vertically averaged ice sheet models. The model follows the flow of ice along a flow line within an ice sheet drainage basin. Longitudinal stresses and basal sliding are included. Basal sliding is dependent on the base shear stress and a specified distribution of basal water pressure. The numerical methods used to solve the coupled set of stress and velocity equations for the static and time-evolutionary cases are discussed. A steady state profile simulating an ice stream is calculated for a particular set of input parameters, and changes in the profile are examined for different choices of parameters. Preliminary studies of response behavior are completed using a simplified ice sheet geometry with a fixed terminus or grounding line. The results of these studies illustrate ice sheet thinning in response to a lowered sea level or to a reduction in the extent of ice rises (or pinning points) within ice shelves.

Bindschadler, R. A.↗

Forced, stationary waves in a linear, stratified, quasi-geostrophic atmosphere

A finite difference model and an approximate WKB analysis were employed to test the validity of three of the Smagorinsky conclusions (1953) regarding the influence of diabatic heating upon the resultant stationary eddies. The conclusions comprised a necessity of including surface friction to avoid resonance, to account for stratospheric influence to accurately estimate the magnitude of the disturbances in the upper third of the troposphere, and the adequacy of the linear model for describing the gross features of sea-level normals at middle and high latitudes. Results of the WKB analysis of the effects of orography and diabatic heating demonstrate that streamfunctions are produced when orography forces a stationary solution. The surface friction is concluded to have a negligible effect on the solutions when the wind speeds are low. The solutions, however, require the presence of a lid for the middle troposphere to eliminate resonance responses.

Roads, J. O.↗

Numerical simulation of the development of mean monsoon circulation in July

Eight different experiments are carried out, ranging from 8 to 20 days, with a primitive equation model consisting of five atmospheric layers and one oceanic layer. The purpose is to investigate the relative importance of radiative heating and deep cumulus condensation, orography, and initial conditions for the development of the mean monsoon circulation from June to July in the 0-180 deg E, 25 deg S - 55 deg N region. Two alternative initial states are used, one based on the observed monthly mean June pressure distribution, the other on the mean June zonal average pressure distribution. Whereas large-scale condensation and actual land and sea distributions are included in every experiment, deep cumulus cone condensation and radiative heating are always taken together. It is found that the means sea level pressure distribution and low-level flow pattern produced by these simulations are in the main determined by the diabatic heating distribution and are influenced somewhat by orography; they are, however, almost independent of the initial state. The low pressure systems are found to develop faster when diurnal variation of solar radiation is allowed for; this is thought to be due mainly to the more vigorous cumulus activity during the day.

Kuo, H. L.↗

On the nonlinear versus linearized lower boundary conditions for topographically forced stationary long waves

For quasi-geostraphic stationary long waves forced by topography, the nonlinear lower boundary condition is derived in terms of the geopotential height and compared with the linearized version. The common practice of replacing terms describing the flow over and around a mountain by upstream zonal flow over the mountain and evaluating the resulting condition at sea level is found to be a good approximation for the cases considered and does not need to be modified as sometimes suggested. Specifically, it is found that this approximation does not affect, for most cases, the lower boundary condition expressed in terms of the geopotential height provided that the stationary wave is not near resonance. At resonance, the eddy advection terms may become important for large-amplitude waves when dissipation and surface diabatic heating are taken into account.

Tung, K. K.↗

Marine biological controls on atmospheric CO2 and climate

It is argued that the ocean is losing N gas faster than N is being returned to the ocean, and that replenishment of the N supply in the ocean usually occurs during ice ages. Available N from river and estruarine transport and from rainfall after formation by lightning are shown to be at a rate too low to compensate for the 10,000 yr oceanic lifetime of N. Ice sheets advance and transfer moraine N to the ocean, lower the sea levels, erode the ocean beds, promote greater biological productivity, and reduce CO2. Ice core samples have indicated a variability in the atmospheric N content that could be attributed to the ice age scenario.

Mcelroy, M. B.↗

Interannual variability of the equatorial Pacific - Revisited

Wind-driven modeling results are presented which indicate that a significant portion of the observed interannual sea level variability of the eastern, central equatorial, and western Pacific may be accounted for by linear theory when reasonable estimates of the wind field are provided. It is noted that drastic shoaling of the pycnocline in the western Pacific during El Nino may be induced by Rossby waves that are excited by changes in strength and position of the northeast trades. In the eastern tropical Pacific, remotely forced Kelvin waves generated in the central and western Pacific are responsible for the El Nino pycnocline displacements.

Busalacchi, A. J.↗

Preliminary flight test results of the F100 EMD engine in an F-15 airplane

A flight evaluation of the F100 Engine Model Derivative (EMD) is conducted. The F100 EMD is an advanced version of the F100 engine that powers the F15 and F16 airplanes. The F100 EMD features a bigger fan, higher temperature turbine, a Digital Electronic Engine Control system (DEEC), and a newly designed 16 segment afterburner, all of which results in a 15 to 20 percent increase in sea level thrust. The flight evaluations consist of investigation of performance (thrust, fuel flow, and airflow) and operability (transient response and airstart) in the F-15 airplane. The performance of the F100 EMD is excellent. Aircraft acceleration time to Mach 2.0 is reduced by 23 percent with two F100 EMD engines. Several anomalies are discovered in the operability evaluations. A software change to the DEEC improved the throttle, and subsequent Cooper Harper ratings of 3 to 4 are obtained. In the extreme upper left hand corner of the flight enveloped, compressor stalls occurr when the throttle is retarded to idle power. These stalls are not predicted by altitude facility tests or stability for the compressor.

Myers, L. P.↗

Capabilities and limitations of the Jicamarca radar as an MST radar

The Jicamarca radar (Long. 76.52W, Lat. 11.56S), located at 20 km from Lima at approximately 500 meters over sea level, is surrounded by mountains which provide a good shield from man-made interference. The radio horizon goes from a few hundred meters, across the dry valley where it is located, to 15 km, along the valley in the direction of the continental divide. This limits the clutter to 15 km, except for one high peak at 21 km. It is the most equatorial of all existing MST radars. Its proximity to the Andes, makes its location unique for the study of lee waves and orographic-induced turbulence. Vertical as well as horizontal projections of MST velocities are obtained by simultaneously pointing with different sections of the antenna into three or four different directions. The transmitters, receivers, and systems for data acquisition, processing, and control are included.

Woodman, R. F.↗

Diffuser/ejector system for a very high vacuum environment

Turbo jet engines are used to furnish the necessary high temperature, high volume, medium pressure gas to provide a high vacuum test environment at comparatively low cost for space engines at sea level. Moreover, the invention provides a unique way by use of the variable area ratio ejectors with a pair of meshing cones are used. The outer cone is arranged to translate fore and aft, and the inner cone is interchangeable with other cones having varying angles of taper.

Riggs, K. E.↗