Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROLLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Progress in Navier-Stokes Simulation of Delta Wing Maneuver Aerodynamics

This paper will summarize recent progress in the numerical simulation of high incidence vortical flow about a generic 65 degree sweep delta wing using the three dimensional, time-dependent, Reynolds averaged, Navier-Stokes (RANS) equations. Computations have been carried out at 15 and 30 degrees angle of attack under subsonic turbulent flow conditions, and compared with experimental data provided by Hanff, Jenkins, and their colleagues. This work has already been published elsewhere and widely disseminated. Computations carried out at 15 degrees angle of attack included static roll angles ranging up to 65 degrees, and a large-amplitude (40 degree), high rate (7 Hz), forced roll motion. There was very good agreement between computed and experimental forces and moments, and static surface pressures. There was a significant hysteresis of the dynamic rolling moment due to the high rate of roll motion. At this angle of attack, no vortex breakdown was observed in the computations or experiment. Computations were also carried out at 30 degrees angle of attack, where vortex breakdown was present in both the computations and experiment. There was overall good agreement in the computed and experimental forces and moments. The static rolling moment varied with roll angle in a highly nonlinear manner, and exhibited three stable trim points and two unstable trim points. This behavior was attributed to the presence of vortex breakdown. Two large-amplitude (30 degrees), high-rate (10 Hz) forced roll motions were computed. The dynamics of the vortex breakdown motion was dramatically visualized by tracking the time-dependent motion of particles released near the delta wing apex. This numerical visualization is analogous to experimental smoke flow techniques. In one of the dynamic cases the breakdown was found to move off the wing, convected downwind of the trailing edge, and later reformed near the trailing edge through an instability of the vortex core. A damped free-to-roll motion was also computed by releasing the wing from rest at 40 degrees of roll. The wing went to the same trim point as in the experiment.

Chaderjian, Neal M.↗

Flight Test of the F/A-18 Active Aeroelastic Wing Airplane

A viewgraph presentation of flight tests performed on the F/A active aeroelastic wing airplane is shown. The topics include: 1) F/A-18 AAW Airplane; 2) F/A-18 AAW Control Surfaces; 3) Flight Test Background; 4) Roll Control Effectiveness Regions; 5) AAW Design Test Points; 6) AAW Phase I Test Maneuvers; 7) OBES Pitch Doublets; 8) OBES Roll Doublets; 9) AAW Aileron Flexibility; 10) Phase I - Lessons Learned; 11) Control Law Development and Verification & Validation Testing; 12) AAW Phase II RFCS Envelopes; 13) AAW 1-g Phase II Flight Test; 14) Region I - Subsonic 1-g Rolls; 15) Region I - Subsonic 1-g 360 Roll; 16) Region II - Supersonic 1-g Rolls; 17) Region II - Supersonic 1-g 360 Roll; 18) Region III - Subsonic 1-g Rolls; 19) Roll Axis HOS/LOS Comparison Region II - Supersonic (open-loop); 20) Roll Axis HOS/LOS Comparison Region II - Supersonic (closed-loop); 21) AAW Phase II Elevated-g Flight Test; 22) Region I - Subsonic 4-g RPO; and 23) Phase II - Lessons Learned

Voracek, David↗

Control system and method for tapered structure construction

A control system for forming a tapered structure includes a sensor providing feedback for a machine for forming a tapered structure including at least three rolls having at least one bend roll and at least two guide rolls. The guide rolls may include rollette banks having a plurality of rollettes. The machine may also include an adjustment mechanism to position at least one of the rolls, where a diameter of the tapered structure being formed is controlled by relative positions of the rolls. The machine may also include a joining element to join edges of a stock of material together as it is rolled through the rolls to form the tapered structure. The control system may also include a controller to receive feedback from the sensor and to send a control signal based on the feedback to the adjustment mechanism for positioning at least one of the rolls.

Takata, Rosalind K.↗

Control system and method for tapered structure construction

A control system for forming a tapered structure includes a sensor providing feedback for a machine for forming a tapered structure including at least three rolls having at least one bend roll and at least two guide rolls. The guide rolls may include rollette banks having a plurality of rollettes. The machine may also include an adjustment mechanism to position at least one of the rolls, where a diameter of the tapered structure being formed is controlled by relative positions of the rolls. The machine may also include a joining element to join edges of a stock of material together as it is rolled through the rolls to form the tapered structure. The control system may also include a controller to receive feedback from the sensor and to send a control signal based on the feedback to the adjustment mechanism for positioning at least one of the rolls.

Takata, Rosalind K.↗

Engineered pinning landscapes for enhanced 2G coil wire

We demonstrate a twofold increase in the in-field critical current of AMSC's standard 2G coil wire by irradiation with 18-MeV Au ions. The optimum pinning enhancement is achieved with a dose of 6 × 10 11 Au ions/cm 2 . Although the 77 K, self-field critical current is reduced by about 35%, the in-field critical current (H//c) shows a significant enhancement between 4 and 50 K in fields > 1 T. The process was used for the roll-to-roll irradiation of AMSC's standard 46-mm-wide production coated conductor strips, which were further processed into standard copper laminated coil wire. The long-length wires show the same enhancement as attained with short static irradiated samples. The roll-to-roll irradiation process can be incorporated in the standard 2G wire manufacturing, with no modifications to the current process. In conclusion, the enhanced performance of the wire will benefit rotating machine and magnet applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of cold deformation on the recrystallization behavior of FePd alloy at the ordering temperature using electron backscatter diffraction

In this study, the evolution of the recrystallization texture and microstructure was investigated after annealing of 50% and 90% cold-rolled FePd alloy at 530 °C. The FePd alloy was produced by vacuum arc melting in an atmosphere of 97% Ar and 3% H{sub 2}. The specimens were cold rolled to achieve 50% and 90% reduction in thickness. Electron backscatter diffraction measurements were performed on the rolling direction–normal direction section. With increased deformation from 50% to 90%, recrystallized texture transition occurs. For the 50% cold-rolled alloy, the preferred orientation is (0 1 0) [11 0 1], which is close to the cubic orientation after 400 h of annealing. For the 90% cold-rolled alloy, the orientation changes to (0 5 4) [22–4 5] after 16 h of annealing. - Highlights: • Texture and microstructure in cold-rolled FePd alloy was investigated during annealing using EBSD. • The recrystallized texture of 50% cold-rolled FePd is (0 1 0) [11 0 1] at 530 °C for 400 hours. • The recrystallized texture of 90% cold-rolled FePd is changed to (0 5 4) [22–4 5] at 530 °C after 16 hours.

36 MATERIALS SCIENCE↗

Effect of pre-annealing deformation on the recrystallized texture and grain boundary misorientation in commercial pure titanium

Highlights: • Tailoring the misorientation angle distribution by pre-annealing rolling in CP-Titanium. • Enhancing the inheritance of basal scatter texture by medium pre-annealing rolling. • Moderate pre-annealing rolling produces refined recrystallized grains. - Abstract: The effects of rolling reduction followed by annealing (at 650 °C) on commercial pure titanium sheet are investigated. The microstructure, texture and misorientation angle distributions after rolling and annealing are observed by electron back scatter diffraction (EBSD). It is found that, when the rolling deformation was low (20%) or medium (40%), a fraction of non-TD-split basal texture is inherited from the deformed state and remains even after long time (60 min) annealing. However, heavy rolling deformation (85%) causes a strong and typical TD-split basal texture in the deformed and annealed states. In addition, the misorentation angle distributions are relatively homogeneous for the recrystallized samples with a low or medium pre-annealing deformation. But with heavy pre-annealing deformation, the misorientation angle distributions exhibits two peaks, around 15–30° and 70–80°. The texture and misorientation angle evolution mechanisms are discussed in this work. The study shows the possibility to tailor the texture and the misorientation angle distribution of commercial pure titanium sheet by ordinary rolling process.

36 MATERIALS SCIENCE↗

A high-performance β-solidifying TiAl alloy sheet: Multi-type lamellar microstructure and phase transformation

Highlights: • A high-performance β-solidifying TiAl alloy sheet is fabricated via hot rolling. • Fine multi-type β/γ and α{sub 2}/γ lamellar structures are formed during hot-rolling. • These lamellar structures are induced by the β → γ and α + γ → α{sub 2} + γ/γ{sub T} transformations. • The nano-scaled antiphase domain is induced by α → α{sub 2} disorder-order transformation. • The fine multi-type lamellar structures contribute to the strength enhancement. - Abstract: TiAl alloys are widely used in the aerospace industry and, hence, a thorough understanding of the corresponding microstructural evolution is crucial for providing insight into the fabrication of high-performance TiAl alloy sheets. In this study, a high-performance β-solidifying Ti-43Al-9V-0.2Y alloy sheet with multi-type lamellar structures was obtained via hot-rolling at an initial rolling temperature of 1260 °C. Owing to the temperature drop and reheat associated with multi-pass rolling, relatively fine irregular β/γ and regular α{sub 2}/γ lamellar microstructures (average size: ~25 μm) with nano-scaled antiphase domains (APDs) were generated by the β → γ and α + γ → α{sub 2} + γ/γ{sub T} phase transformations. These two lamellar structures have different formation mechanisms. The results of electron backscatter diffraction and transmission electron microscopy revealed that the nucleation and growth of (i) β/γ and (ii) α{sub 2}/γ lamellar structures are induced mainly by (i) stress and (ii) a combination of the stress and temperature drop during hot-rolling, respectively. Thin γ{sub T} precipitates from the α/α{sub 2} or γ phases. This precipitation is induced by the higher stress and lower temperature associated with the later stage (compared with those occurring in the initial stages) of hot-rolling. Moreover, compared with the corresponding as-forged alloy, the as-rolled TiAl alloy sheet exhibits better performance at both room and elevated temperatures. The improvement in the tensile properties is attributed to the duplex microstructure consisting of fine multi-type lamellar structures with nano-scaled APDs. The interface boundaries of β/γ, α{sub 2}/γ and APDs, which are effective in retarding dislocation motion, contribute mainly to strengthening of the alloy sheet.

36 MATERIALS SCIENCE↗

The significant impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels

Highlights: • Parts of metastable austenite transformed into strain-induced martensite in 18Cr-8Ni stainless steel during cold-rolled process. • The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. • The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination. - Abstract: The present study aims to investigate the impact of cold deformation on structure-property relationship in phase reversion-induced stainless steels. The commercial 18Cr-8Ni stainless steel was cold rolled at room temperature to 30%, 60% and 90% thickness reduction, respectively and subsequently annealed at 900 °C for 1–100 min. Evolution of phases in selected samples was identified and quantified by X-ray diffraction together with the corresponding microstructural characterization through optical, scanning and transmission electron microscopy, and electron backscatter diffraction. Mechanical properties of selected samples were determined by the tensile test. The results indicated that parts of metastable austenite transformed into strain-induced martensite during cold rolling process, and the volume fraction of martensite increased with increase in cold rolling reduction. The kinetics of reversion transformation from martensite to austenite was fastest in 90% cold-rolled sample during annealing treatment. The austenite grain size for the 90% cold-rolled sample after annealing was smallest and most uniform, which induced highest yield strength and elongation combination.

36 MATERIALS SCIENCE↗

The influence of thermomechanical treatment pathways on texture and mechanical properties in ARB Cu/Nb nanolaminates

Accumulative roll-bonded Cu/Nb nanolaminates (ARB Cu/Nb) possess high strength, thermal stability, and radiation tolerance arising from a high content of heterophase interfaces at fine layer thicknesses. These properties can be tailored by processing parameters used in the ARB Cu/Nb fabrication process, in which layer thickness, thermal history, and strain pathway determine the interface types and resultant properties found in the material. In this work, we subject ARB Cu/Nb to annealing, and then two different rolling pathways – one where rolling direction is held constant (longitudinal rolling, or LR), and one where rolling direction is rotated by 90º and held constant thereafter (cross rolling, or CR). Rolling is performed on ARB Cu/Nb over a targeted range of layer thicknesses from 193 to 25 nm and resultant bulk textures measured by neutron diffraction are correlated with mechanical properties measured by miniaturized tensile tests. The annealing procedure sharpens texture in both phases. We find that Cu mostly develops the same texture in LR and CR. In contrast, Nb develops a distinct texture along the CR pathway that is distinct from the LR texture. The composite texture of Cu/Nb is thus distinct between LR and CR pathways. This difference in texture development between Cu and Nb as a function of strain after change in rolling direction demonstrates the viability for deliberate pairing of Cu LR and Nb CR textures at a desired layer thickness. For mechanical properties, we find that differences in texture do not result in yield or flow stress differences above a layer thickness of 25 nm. Below a layer thickness of 25 nm, despite similar Taylor factors, yield and flow stress and are significantly different. In conclusion, this indicates texture only influences mechanical behavior at low layer thickness, where interface structure dominates mechanical properties.

36 MATERIALS SCIENCE↗

The influence of bi-metal interfaces on deformation mechanisms in bulk nanolaminar composites

In this presentation, we report on the plastic deformation mechanisms in Ag-Cu and Cu-Nb nanocomposites rolled to large reductions. Starting with an Ag-Cu alloy with eutectic lamellar bilayer thickness of 200 nm, we roll the as-cast rods from 9.5 mm diameter to sheets of final thickness varying from 2.4 mm to 500 {micro}m, corresponding to 75% to 95% nominal reduction in thickness. Cu(111) X-ray pole figures of the rolled nanocomposites indicate a measured texture similar to that of Ag but different from that expected during rolling of pure bulk Cu involving dislocation slip alone. Visco-Plastic Self Consistent (VPSC) polycrystal modeling indicate that both silver and copper deformed by slip and twinning and the twin fraction reached over 30%, depending on rolling reduction. Because pure Cu is not expected to twin under these processing conditions, we hypothesize that twinning in Cu is induced by twinning in Ag, aided by the presence of high Ag-Cu interfacial content. Molecular Dynamics (MD) simulations are then carried out on perfect and defective Ag-Cu interfaces and the results support this hypothesis. In the Cu-Nb system, it has been found that at individual layer thicknesses of 40 nm and above, physical vapor deposited foils can be rolled to large strains. However, when the layer thickness decreases to {approx}5nm, shear instability during rolling limits ductility. In this work, we show the effects of cladding 5nm CuINb multilayers with 40 nm CuINb multilayers to limit the onset of geometric instability, thereby facilitating the deformation of 5nm Cu/Nb multi layers to large rolling strains. Results will be discussed in terms of the effects of the interface on deformation processes at diminishing length scales.

36 MATERIALS SCIENCE↗

The characterization of shape memory effect for low elastic modulus biomedical {beta}-type titanium alloy

This work investigates the textures of biomedical TiNbTaZr alloy rolled by 99% cold reduction ratios in thickness. The relationship between textures and superelasticity of the specimens treated at 873 K and 1223 K for 1.2 ks is studied. The microstructure of tensile specimen is investigated by transmission electron microscopy. Textures of cold-rolled and heat-treated specimens are studied. During unloading, the anisotropy of superelastic strain and pure elastic strain in the heat-treated specimens is observed. Superelastic strain along rolling direction and transverse direction is larger than those along 45 deg. from rolling direction while pure elastic strain shows the highest value along 45 deg. from rolling direction in the specimen treated at 873 K. For the specimen treated at 1223 K, higher pure elastic strain is obtained along rolling direction. The maximum recovered strain around 2.11% is obtained along rolling direction.

36 MATERIALS SCIENCE↗

Imaging Complex Subsurface Structures for Geothermal Exploration at Pirouette Mountain and Eleven-Mile Canyon in Nevada

Accurate imaging of subsurface complex structures with faults is crucial for geothermal exploration because faults are generally the primary conduit of hydrothermal flow. It is very challenging to image geothermal exploration areas because of complex geologic structures with various faults and noisy surface seismic data with strong and coherent ground-roll noise. In addition, fracture zones and most geologic formations behave as anisotropic media for seismic-wave propagation. Properly suppressing ground-roll noise and accounting for subsurface anisotropic properties are essential for high-resolution imaging of subsurface structures and faults for geothermal exploration. We develop a novel wavenumber-adaptive bandpass filter to suppress the ground-roll noise without affecting useful seismic signals. This filter adaptively exploits both characteristics of the lower frequency and the smaller velocity of the ground-roll noise than those of the signals. Consequently, this filter can effectively differentiate the ground-roll noise from the signal. We use our novel filter to attenuate the ground-roll noise in seismic data along five survey lines acquired by the U.S. Navy Geothermal Program Office at Pirouette Mountain and Eleven-Mile Canyon in Nevada, United States. We then apply our novel anisotropic least-squares reverse-time migration algorithm to the resulting data for imaging subsurface structures at the Pirouette Mountain and Eleven-Mile Canyon geothermal exploration areas. The migration method employs an efficient implicit wavefield-separation scheme to reduce image artifacts and improve the image quality. Our results demonstrate that our wavenumber-adaptive bandpass filtering method successfully suppresses the strong and coherent ground-roll noise in the land seismic data, and our anisotropic least-squares reverse-time migration produces high-resolution subsurface images of Pirouette Mountain and Eleven-Mile Canyon, facilitating accurate fault interpretation for geothermal exploration.

15 GEOTHERMAL ENERGY↗

Radioguided localisation of impalpable breast lesions using 99m-Technetium macroaggregated albumin: Lessons learnt during introduction of a new technique to guide preoperative localisation

Preoperative wire-guided localisation (WGL) of impalpable breast lesions is widely used but can be technically difficult. Risks include wire migration, inaccurate placement, and inadequate surgical margins. Research shows that radioguided occult lesion localisation (ROLL) is quicker, easier, and can improve surgical and cosmetic outcomes. An audited introduction of ROLL was conducted to validate the technique as a feasible alternative to WGL. Fifty patients with single impalpable lesions and biopsy proven malignancy or indeterminate histology underwent WGL followed by intralesional radiopharmaceutical injection of 99m-Technetium macroaggregated albumin. Postprocedural mammography was performed to demonstrate wire position, and scintigraphy to evaluate radiopharmaceutical migration. Lymphoscintigraphy and intraoperative sentinel node biopsy were performed if indicated, followed by lesion localisation and excision using a gamma probe. Specimen imaging was performed, with immediate reexcision for visibly inadequate margins. Accurate localisation was achieved in 86% of patients with ROLL compared to 72% with WGL. All lesions were successfully removed, with clear margins in 71.8% of malignant lesions. Reexcision and intraoperative sentinel node localisation rates were equivalent to preaudit figures for WGL. ROLL was easy to perform and problems were infrequent. Inaccurate radiopharmaceutical placement necessitating WGL occurred in four patients. Minor radiopharmaceutical migration was common, but precluded using ROLL in only two cases. ROLL is effective, simple, inexpensive, and easily learnt; however, preoperative confirmation of correct radiopharmaceutical placement using mammography and the gamma probe is important to help ensure successful lesion removal. Insertion of a backup hookwire is recommended during the initial introduction of ROLL.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Complete Status Report Documenting the Development of Friction Stir Welding for Producing a Butt Joint in Thin Wall Tubing of ODS Alloys

A challenging attempt using friction stir welding to produce a butt joint between two 1.0 mm thick plates of 14YWT was nearly successful. The modified tool pin mostly penetrated the thickness of the adjoined thin plate samples resulting in a small blunt notch on the bottom surface of the butt joint. A bend occurred in the thin plate sample due to formation of stresses from clamping the thin plate sample during FSW. The peak displacement of the bend occurred along the center line of the butt joint. The weld zone showed good microstructure mixing with some flashing mostly on the retreating side that suggested excess heat input by friction between the traveling and spinning tool pin and thin plates of 14YWT. Neutron diffraction experiments were performed on the bent sample of 14YWT to measure the residual stresses in the butt joint on the HB-2B beam line at the Neutron Residual Stress Facility at HFIR. However, the neutron scattering to background noise ratio was very low during data acquisition. Measurements of lattice strains were obtained in the rolling (RD) and normal (ND) directions but not in the extrusion direction (ED) of the thin plate sample. Unfortunately, the quality of the data was not sufficient for determining the residual stresses in the butt joint. From the previous neutron scattering experiments conducted on four hot rolled plates (R1, R2, R3 and R4) of 14YWT, the residual stresses were calculated from lattice strain data and plotted in 2-D color contour maps for ED, RD and ND. The results showed variations in the magnitude and spatial position of residual stresses in the microstructure of the four plates. The magnitude in residual stresses in ED and RD increased gradually with increasing rolling deformation for R1 (50%) to R2 (76%), followed by larger increases in R3 (89%) and R4 (95%). The maximum peaks in residual stresses for R4 was ~710-730 MPa in ED and RD. The residual stresses in ND were below ~300 MPa for each of the 4 rolled plates, with a maximum residual stress in R4 (95%) of ~400 MPa. These results indicated that significant residual stresses representing ~57% of the yield stress of 14YWT (SM13) had accumulated in the 14YWT plate after hot rolling to the 1 mm thickness, which was used in the FSW experiments. The microstructure analysis of the 1.0 mm thick plate of 14YWT containing the butt joint produced by FSW revealed significant changes in the grain structure and texture between the unaffected zone (UZ) of the rolled plate and the butt joint weld. In the UZ, the grains were severely elongated after 95% deformation and mainly possessed the {101} texture component in the ED. Two predominant grain misorientation angles were observed: one consisting of small misorientations of <5º between highly elongated grains and the other consisting of large misorientations of >15º in pockets of small grains that might have formed by dynamic recrystallization processes during rolling of the plate at 1000ºC. The morphology and texture of grains in the heat affected zone (HAZ) were similar to those in UZ, except the grains had coarsened due to excess heat input during FSZ. A population of pores formed and the grains both coarsened and changed to isotropic morphology in the microstructure of the butt joint on both the advancing and retreating sides. The texture of grains in both regions were randomly orientated between the 3 poles {001}, {101} and {111}. The main difference in texture of grains between the advancing side and retreating side was with the misorientation angles of neighboring grains. Most of the grains in the advancing side had misorientation angles of >5º indicating that these grains experienced recrystallization. On the retreating side, areas containing larger grains showed high misorientation angles of >15º compared to areas appearing as bands of grains with misorientation angles of <5º and between 5º-15º. Numerous small pockets of grains with low misorientation angles of <5º were distributed in the microstructure among the grains showing high misorientation angles of >15º. It was determined that the grains associated with low misorientation angles contained sub-grain structures, which was consistent with both recrystallization and recovery mechanisms for grains located on the retreating side of the butt joint. These results demonstrate the complex microstructure that evolves in the microstructure of 14YWT resulting from the input of high temperatures and severe deformations during FSW.

36 MATERIALS SCIENCE↗

A preliminary look at the effects of coupled lateral modes on aircraft handling qualities

Analytic and six-degree-of-freedom motion base simulator studies have been conducted to better understand how the coupled roll-spiral and coupled roll-aileron actuator modes affect aircraft handling qualities. The results reported herein are preliminary and are subject to change until other aircraft and several more data points can be examined. The results obtained thus far indicate that when the roll-spiral coupled mode is brought about by unusual values of an aircraft's stability and control derivatives, the lateral-directional handling qualities will invariably be degraded. However, when the roll spiral coupling is brought about by a roll-rate command/roll-attitude hold stability and control augmentation system (SCAS), the requirements for satisfactory handling qualities can be correlated to the natural frequency and the damping of the coupled mode. Satisfactory handling qualities were also achieved when the lateral SCAS brought about a coupling of the roll mode with the aileron actuator mode. In this case, the pilot ratings indicate that the handling qualities may be correlated to the natural frequency of the coupled roll-aileron mode.

Ruflin, S. J.↗

Unsteady surface pressure measurements on a slender delta wing undergoing limit cycle wing rock

An experimental investigation of slender wing limit cycle motion known as wing rock was investigated using two unique experimental systems. Dynamic roll moment measurements and visualization data on the leading edge vortices were obtained using a free to roll apparatus that incorporates an airbearing spindle. In addition, both static and unsteady surface pressure data was measured on the top and bottom surfaces of the model. To obtain the unsteady surface pressure data a new computer controller drive system was developed to accurately reproduce the free to roll time history motions. The data from these experiments include, roll angle time histories, vortex trajectory data on the position of the vortices relative to the model's surface, and surface pressure measurements as a function of roll angle when the model is stationary or undergoing a wing rock motion. The roll time history data was numerically differentiated to determine the dynamic roll moment coefficient. An analysis of these data revealed that the primary mechanism for the limit cycle behavior was a time lag in the position of the vortices normal to the wing surface.

Arena, Andrew S., Jr.↗

Aerodynamic control of NASP-type vehicles through vortex manipulation. Volume 3: Wing rock experiments

Free-to-roll tests were conducted in water and wind tunnels in an effort to investigate the mechanisms of wing rock on a NASP-type vehicle. The configuration tested consisted of a highly-slender forebody and a 78 deg swept delta wing. In the water tunnel test, extensive flow visualization was performed and roll angle histories were obtained. In the wind tunnel test, the roll angle, forces and moments, and limited forebody and wing surface pressures were measured during the wing rock motion. A limit cycle oscillation was observed for angles of attack between 22 deg and 30 deg. In general, the experiments confirmed that the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. The variation of roll acceleration (determined from the second derivative of the roll angle time history) with roll angle clearly slowed the energy balance necessary to sustain the limit cycle oscillation. Different means of suppressing wing rock by controlling the forebody vortices using small blowing jets were also explored. Steady blowing was found to be capable of suppressing wing rock, but significant vortex asymmetrices are created, causing the model to stop at a non-zero roll angle. On the other hand, alternating pulsed blowing on the left and right sides of the fore body was demonstrated to be a potentially effective means of suppressing wing rock and eliminating large asymmetric moments at high angles of attack.

Suarez, Carlos J.↗