Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RESINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Study on the Properties of Novel Soft Magnetic Composites of FeSiAl

In this paper, we compounded the FeSiAl powder with a novel amorphous inorganic insulation agent (AIIA). Silicone resin (3 wt.%) was used as organic insulating agent, and the inorganic insulating agent was Fe{sub 83.5}Si{sub 7.5}B{sub 5}Cr{sub 4} amorphous powder (0, 1, 2, 3, and 4 wt.%). Amorphous powder was prepared by passivation pretreatment before compounding. The results showed that the addition of amorphous inorganic insulating agent will significantly affect the soft magnetic properties of FeSiAl powders. Compared with the pure FeSiAl powder having only silicone resin the saturation magnetization of composite powders slightly increased (by 0.1–4.9%). When AIIA content was 2 wt.%, the sample had the highest initial permeability, which increased by 14.6%. At the same time, the core loss was also reduced by 15.7% (B{sub m} = 5 mT, f = 1000 kHz) when AIIA content was also 2 wt.%.

36 MATERIALS SCIENCE↗

Californium purification and electrodeposition

The staff at the Radiochemical Engineering Development Center, located at Oak Ridge National Laboratory, produced a 6.3 ± 0.4 GBq (1.7 ± 0.1 Ci) 252 Cf source for the Californium Rare Isotope Breeder Upgrade (CARIBU) project at Argonne National Laboratory’s Argonne Tandem Linac Accelerator System. The source was produced by electrodeposition of a 252 Cf sample onto a stainless steel substrate, which required material free from excess mass for efficient deposition. The resulting deposition was the largest reported 252 Cf electrodeposition source ever produced. Several different chromatographic purification methods were investigated to determine which would be most effective for final purification of the feed material used for the CARIBU source. The separation of lanthanides from the Cf was of special concern. Furthermore, the separation, using 145 Sm, 153 Gd, and 249 Cf as tracers, was investigated using BioRad AG 50X8 in α-hydroxyisobutyric acid, Eichrom LN resin in both HNO 3 and HCl, and Eichrom TEVA resin in NH 4 SCN. The TEVA NH 4 SCN system was found to completely separate 145 Sm and 153 Gd from 249 Cf and was adopted into the purification process used in purifying the 252 Cf.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Development of field-based separations for the rapid identification of uranium and plutonium

The development of rapid, radioanalytical techniques to separate uranium and plutonium from complex, field samples are needed for the timely and accurate determination of nuclear material origin, and processing activities. Widespread use of nuclear power and technology in the world has increased demands on analytical laboratories from the monitoring of numerous low-level, environmental samples with variable compositions. Environmental sampling has proven to be one of the strongest technical measures for detecting nuclear material and activities. With the increase in sampling demands, new technologies must offer improvements such as automation, high throughput, reproducible chemical separations, short analysis times, and reduced costs to be effective. We have been developing a portable, separations system for uranium (U) and plutonium (Pu) separations based upon selective extraction of target elements using an extraction chromatographic resin which would allow for simple and fast identifcation when coupled with the appropriate sample digestor and detection systems. The microfluidic design minimizes elution volumes and concentrates the elements of interest in a purified stream. Flowsheet development and testing was demonstrated on a single, micro-column system with an acidified, iron, uranium, and plutonium nitrate stream. The recovery of Pu was optimized by examining various reducing agents at different concentrations for rapid, quantitative recovery from the flow-through design. Quantitative recovery and high selectivity of U and Pu was achieved in the appropriate stripping stages and provided purified and concentrated U and Pu streams. The microfluidic system suggests automation in a small, footprint unit while exploiting the in-line processing of extraction chromatographic resins as the primary means of concentrating the radionuclides from the raw acidic feed and separating the elements into purified streams.

Extraction Chromatography↗

A new method for separating first row transition metals and actinides from synthetic melt glass

A new method was developed for separating Co, Fe, and Sc from complex debris matrices using the extraction chromatography resin DGA. The activation products Co-58, Mn-54, and Sc-46 were used to characterize the separation of the synthetic melt glass solutions. In the separation scheme that was developed, Au, Co, Cu, Fe, Sc, and Ti were separated from the rest of the sample constituents. In this paper, the synthetic melt glass separation method, efficiency, recoveries, and the length of procedure will be discussed. In conclusion, batch contact adsorption studies for Na and Sc for DGA resin are discussed as well.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Chromatographic separation of americium from europium using bis-2,6-(5,6,7,8-tetrahydro-5,9,9-trimethyl-5,8-methano-1,2,4-benzotriazin-3-yl) pyridine

The separation of americium(III) from europium(III) was achieved utilizing a bis-2,6-(5,6,7,8-tetrahydro-5,9,9-trimethyl-5,8-methano-1,2,4-benzotriazin-3-yl) pyridine (CA-BTP) chromatographic resin. The extraction chromatographic materials were prepared using various concentrations of CA-BTP. This new, hydrolytically stable extractant was impregnated on an inert polymeric support at 40% loading. The uptake of Am(III) and Eu(III) by this material from 0.1 to 4.0 M aqueous HNO 3 solutions was measured. The resulting dry weight distribution ratios, D w , indicated a strong preference for Am(III) with little affinity for Eu(III). These results are similar to recently reported solvent extraction studies indicating a maximum uptake of Am(III) in the 0.5–1.0 M HNO 3 range. The resin preparation, performance, and characterization of the Am/Eu separation are reported herein.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluation of SR/ TEVA/ TRU triple stack for separation of activation products

A rapid method to separate Ta, Po, Au, Pt, and W from a sample containing mixed fission and activation products was developed using three commercially available extraction chromatography resins stacked in series. When the separation was tested using all the target activation products, even those with short half-lives were measurable. Finally, combining multiple extraction chromatography resin cartridges in tandem allows for multiple short-lived activation products to be separated from one sample addition without the complication of multiple steps.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Actinium purification from elemental components of stainless steel and aluminum

Radioisotopes of actinium are valuable because of their potential use in the medical industry. Actinium-225 shows promise for treating disease—like cancer—via targeted alpha therapy (TAT), and the longer-lived actinium-227 is the parent of two radionuclides with potential application in TAT radiopharmaceuticals, thorium-227 and radium-223. Continuing progress in the development of these medical applications requires robust and diverse methods for extracting and purifying actinium from a wide range of matrices. Further, to define the strengths and limitations of separation methods commonly employed in actinium processing, we characterized the performance of ion exchange and extraction chromatographic steps for removing contaminants found in stainless steel (chromium, iron, nickel, and silicon) and aluminum from actinium-227. While AG-MP1 anion exchange resin with HCl (aq) successfully removed iron, cation exchanger AG 50W-X8 removed most other contaminants. The most persistent contaminant was aluminum, which was removed using a DGA Normal extraction resin. These results are presented within the context of applying that methodology toward actinium purification strategies.

36 MATERIALS SCIENCE↗

Root exudates induced coupled carbon and phosphorus cycling in a soil with low phosphorus availability

The amount and type of root exudates can influence P availability in the rhizosphere directly by desorption or dissolution of soil minerals, or indirectly by decomposition of soil organic matter (SOM). Here this study aimed to determine the mechanisms by which specific root exudates influence the distribution and availability of P in soils with low P availability. Water, glucose, alanine, and oxalate were delivered through a simulated root into soils for 15 days. Zymography and planar optodes were used to image potential phosphatase activity, and O2 and pH distribution, respectively. Soils were analyzed for resin extractable inorganic P (Pi), dissolved organic C (DOC), water soluble Fe, and Al, and microbial community structure. Characterization of SOM and P were conducted using ultra-high resolution mass spectrometry and 31P solution nuclear magnetic resonance (NMR), respectively. The addition of oxalate resulted in the greatest resin extractable Pi, DOC, and water-soluble Fe, and Al compared to the other exudates suggesting destabilization of mineral associated organic matter (MAOM) and release of organic P (Po). Both 31P solution NMR and ultra-high resolution mass spectrometry analysis provided evidence of mineralization of Po released from the destabilization of MAOM. The study demonstrates the important role microbial and plant-derived metal chelating ligands play in destabilizing MAOM, releasing SOM and importantly Po, that when mineralized may contribute to increasing Pi availability in soils with low P availability.

59 BASIC BIOLOGICAL SCIENCES↗

Static and Dynamic Mechanical Properties of Graphene Oxide-Incorporated Woven Carbon Fiber/Epoxy Composite

This study investigates the synergistic effects of graphene oxide (GO) on the woven carbon fiber (CF)-reinforced epoxy composites. The GO nanofiller was incorporated into the epoxy resin with variations in the content, and the CF/epoxy composites were manufactured using a vacuum-assisted resin transfer molding process and then cured at 70 and 120 °C. An analysis of the mechanical properties of the GO (0.2 wt.%)/CF/epoxy composites showed an improvement in the tensile strength, Young’s modulus, toughness, flexural strength and flexural modulus by ~ 34, 20, 83, 55 and 31%, respectively, when compared to the CF/epoxy composite. The dynamic mechanical analysis of the composites exhibited an enhancement of ~ 56, 114 and 22% in the storage modulus, loss modulus and damping capacity (tanδ), respectively, at its glass transition temperature. The fiber–matrix interaction was studied using a Cole–Cole plot analysis.

36 MATERIALS SCIENCE↗

Study on Microstructures and Mechanical Properties of Foam Titanium Carbide Ceramics Fabricated by Reaction Sintering Process

Foam titanium carbide (TiC) ceramics with a three-dimensional network structure were fabricated by the reaction sintering process, in which polyurethane foam was taken as the template, and TiO{sub 2} and phenolic resin were used as the reactants. Phase, microstructures and fracture morphologies of foam TiC ceramics were characterized by x-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results show that when the mass ratios of phenolic resin and TiO{sub 2} (F/T) are (0.8-1.2): 1, foam TiC ceramics with pure TiC phase can be formed. As the F/T ratios increase, crystal lattice parameters of fabricated foam TiC ceramics become bigger. When the value of F/T decreases from 1.2 to 0.8, grain size of TiC grows larger and microstructures get denser; meanwhile, the compressive strength increases from 0.10 to 1.05 MPa. Additionally, either raising the sintering temperatures or extending holding time can facilitate the completion of the reaction process and increase the compressive strength.

36 MATERIALS SCIENCE↗

Environmentally Friendly Foundry Molding and Core Sands

The paper describes the current state of knowledge in a field where change has been driven in foundry molding sand practice due to the increasing requirements regarding environmental protection. These trends must take into account not only the technological quality and economics of their production process, but also the increasingly stringent requirements related to environmental protection. As part of this study, tests were performed in relation to reducing the toxicity of current molding sands with organic binders, so as to develop new organic binders for foundry practice. Molding sands with binders having various contents of furfuryl alcohol were tested. It was shown that reducing the total furfuryl alcohol content in the binder results in lower strength properties of the molding sands in practice. It was also suggested to replace the use of a furfuryl binder with one based on alkyd resin. The final stage of the study was to demonstrate the desirability of using biomaterials as a component of organic binders for foundry molding sands. Compositions: typical synthetic resins and biodegradable materials were designed as binders to improve the quality of the organic binders used with molding sands.

36 MATERIALS SCIENCE↗

Surface characterization of carbon fiber polymer composites and aluminum alloys after laser interference structuring

Here, the increasing use of Carbon Fiber-reinforced Polymer matrix Composites (CFPC) and aluminum alloys as lightweight materials in the automotive and aerospace industries demands enhanced surface preparation and control of surface morphology prior to joining. In this study, surfaces of both composite and aluminum were prepared for joining using an Nd:YAG laser in a two-beam interference setup, enabling the (a) structuring of the AL 5182 surface, (b) removal of the resin layer on top of carbon fibers, and (c) structuring of the carbon fibers. CFPC specimens of T700S carbon fiber, Prepreg - T8 3 epoxy, 5 ply thick, 0/90o plaques were used. The effect of laser fluence, scanning speed, and number of shots-per-spot was investigated on the removal rate of the resin without an excessive damage of the fibers. Optical micrographs, 3D imaging, and scanning electron microscope (SEM) imaging were used to study the effect of the laser processing on surface morphology.

36 MATERIALS SCIENCE↗

A Techno-economic Analysis for Integrating an Electrochemical Reactor into a Lignocellulosic Biorefinery for Production of Industrial Chemicals and Hydrogen

In this study, we present a techno-economic analysis for integrating an electrochemical reactor into a lignocellulosic biorefinery for the purpose of converting biorefinery lignin to higher-value industrial chemicals with co-generation of hydrogen. We consider how the electrochemical reactor impacts the manufacturing costs for producing biofuel and determine a break-even value for the lignin oxidation product stream, which is the minimum lignin conversion product stream value that renders the cost to produce biofuel the same as in the typical biorefinery concept. We conclude that at low extents of lignin conversion, the break-even product stream value is likely too high for the process to be feasible. However, at higher extents of lignin conversion, the break-even product stream value may be between 1.00 and 2.00/kg, depending on capital cost and other manufacturing costs like depreciation. Here the potential markets for the biomass conversion products include resin manufacturing, where the products would compete with petroleum-derived resin precursors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The dentin organic matrix - limitations of restorative dentistry hidden on the nanometer scale

The prevention and treatment of dental caries are major challenges occurring in dentistry. The foundations for modern management of this dental disease, estimated to affect 90% of adults in Western countries, rest upon the dependence of ultrafine interactions between synthetic polymeric biomaterials and nanostructured supramolecular assemblies that compose the tooth organic substrate. Research has shown, however, that this interaction imposes less than desirable long-term prospects for current resin-based dental restorations. Here we review progress in the identification of the nanostructural organization of the organic matrix of dentin, the largest component of the tooth structure, and highlight aspects relevant to understating the interaction of restorative biomaterials with the dentin substrate. We offer novel insights into the influence of the hierarchically assembled supramolecular structure of dentin collagen fibrils and their structural dependence on water molecules. Secondly, we review recent evidence for the participation of proteoglycans in composing the dentin organic network. Finally, we discuss the relation of these complexly assembled nanostructures with the protease degradative processes driving the low durability of current resin-based dental restorations. We argue in favour of the structural limitations that these complexly organized and inherently hydrated organic structures may impose on the clinical prospects of current hydrophobic and hydrolyzable dental polymers that establish ultrafine contact with the tooth substrate.

60 APPLIED LIFE SCIENCES↗

Nozzle clogging factors during fused filament fabrication of spherical particle filled polymers

Fused filament fabrication with reinforced or filled polymers provides improved material properties compared to ordinary feedstock. A current limitation of these materials is the occurrence of nozzle clogging at higher filler contents. In this paper, an experiment is designed to identify the factors causing nozzle clogging. Glass sphere-filled polycarbonate is investigated by varying nozzle and filler diameters, the resin viscosity, the filler content, and the extrusion pressure. Equations identifying nozzle clogging and intermittent clogging conditions are provided. Based on these results, a model for the clogging of sphere-filled polymers is proposed. Last, a mathematical model is derived, which approximates the printability of filled polymers without the preparation of composites. Finally, this model is based on the nozzle geometry, the filler type and content, the resin viscosity, and the printer’s maximum extrusion force.

36 MATERIALS SCIENCE↗

In situ characterization of material extrusion printing by near-infrared spectroscopy

Material extrusion printing of reactive resins and inks present a unique challenge due to the time-dependent nature of the rheological and chemical properties they possess. As a result, careful print optimization or process control is important to obtain consistent, high quality prints via additive manufacturing. Here, we present the design and use of a near-infrared (NIR) flow through cell for in situ chemical monitoring of reactive resins during printing. Differences between in situ and off-line benchtop measurements are presented and highlight the need for in-line monitoring capability. Additionally, in-line extrusion force monitoring and off-line post inspection using machine vision is demonstrated. By combining NIR and extrusion force monitoring, it is possible to follow cure reaction kinetics and viscosity changes during printing. When combined with machine vision, the ability to automatically identify and quantify print artifacts can be incorporated on the printing line to enable real-time, artificial intelligence-assisted quality control of both process and product. Together, these techniques form the building blocks of an optimized closed-loop process control strategy when complex reactive inks must be used to produce printed hardware.

36 MATERIALS SCIENCE↗

Results of an interlaboratory study on the working curve in vat photopolymerization

The working curve informs resin properties and print parameters for stereolithography, digital light processing, and other photopolymer additive manufacturing (PAM) technologies. First demonstrated in 1992, the working curve measurement of cure depth vs radiant exposure of light is now a foundational measurement in the field of PAM. Despite its widespread use in industry and academia, there is no formal method or procedure for performing the working curve measurement, raising questions about the utility of reported working curve parameters. Here, an interlaboratory study (ILS) is described in which 24 individual laboratories performed a working curve measurement on an aliquot from a single batch of PAM resin. The ILS reveals that there is enormous scatter in the working curve data and the key fit parameters derived from it. Further, the measured depth of light penetration D p varied by as much as 7x between participants, while the critical radiant exposure for gelation E c varied by as much as 70x. This significant scatter is attributed to a lack of common procedure, variation in light engines, epistemic uncertainties from the Jacobs equation, and the use of measurement tools with insufficient precision. The ILS findings highlight an urgent need for procedural standardization and better hardware characterization in this rapidly growing field.

36 MATERIALS SCIENCE↗

Reactor production of promethium-147

In this paper, we describe the 147 Pm production yields and level of impurities from several targets that consisted of milligram quantities of highly enriched 146 Nd oxide irradiated at the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory for durations ranging from 24 to180 h. A comparison between theoretical and experimental data are also presented, and attempts were made to empirically evaluate the neutron capture cross-sections of 41.3-d 148m Pm and 5.4-d 148g Pm. For a one-cycle irradiation (~24 days), 147 Pm yield reaches a maximum value of 101.8 MBq/mg (2.75 mCi/mg) at 60 days after the end of bombardment. Because of large neutron capture cross-sections of 147 Pm, the yield of 147 Pm does not significantly increase with longer irradiation. Our estimates of the thermal neutron capture cross-section and resonance integral for 146 Nd at 1.48 ± 0.05 b and 2.56 ± 0.25 b, respectively, were consistent with the reported values. The effective neutron capture cross-section of 147 Pm to 148m Pm was 53.3 ± 2.7 b - a factor of 2 lower than the 98.7 ± 6.5 b calculated from reported cross-sections. The measured σ eff to the ground state (5.37-d 148g Pm) was 82.0 ± 4.1 b; ~34 % lower than the value of 139 ± 0 b calculated from reported cross-sections. In this work, we also describe the development of a chemical process based on extraction and ion-exchange chromatography for separation of 147 Pm from milligram quantities of 146 Nd and other impurities. Sequential separation of Pm from the Nd target and from other radioisotopic impurities ( 153 Gd and 154&155 Eu, 192 Ir, and 60 Co) was achieved using a LN extraction resin in HCl media followed by further purification of Pm from 60 Co and 192 Ir using a low cross-linking cation exchange resin. Based on these data, we estimated that two rounds of purification under our experimental conditions can provide a mass separation factor of > 104 between Pm and Nd. Our data indicate that curie quantities of 147 Pm with suitable chemical and radioisotopic purity for applications in beta voltaic batteries can be produced by irradiating gram quantities of highly enriched 146 Nd in the flux trap of HFIR for one cycle.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗