Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REFRACTORIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Uranium carbide properties for advanced fuel modeling – A review

Uranium carbides are receiving renewed interest as a preferred nuclear fuel composition for advanced reactors due to their numerous favorable properties. Like many other refractory and transition metal carbides these compounds exist in both hypo- and hyper-stoichiometric compositions which results in significant variations in physical, thermal, and mechanical properties. This manuscript surveys both historic and recent literature to compile important properties data mainly as a function of temperature and carbon content to support fuel performance modeling. Expressions and fits for such properties are also suggested when allowed by complete data sets. Finally, the manuscript also attempts to highlight gaps and discrepancies in the reported data to assist the nuclear fuels community identify key areas that may require further attention in terms of future research and development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Mobility assessment of the BCC and carbide phases in the C-Nb, C-U and Nb-U systems

Uranium carbides with refractory metal additions are considered for Gen IV nuclear reactors and nuclear thermal propulsion as fuels for their high-temperature and corrosion resistant properties. Understanding kinetic effects that dictate microstructural evolution during fabrication and operating conditions is essential to advance technological development of these fuels. This work presents the development of an atomic mobility database for C-Nb-U systems based off available experimental data supported with ab-initio methods. The mobility assessments and uncertainty quantification (using Markov chain Monte Carlo) were conducted in the Kawin software. Carbon diffusion is considered dominant, as metal diffusion is much slower, with niobium diffusion being even slower and rate limiting than uranium metal. We provide a comprehensive and self-consistent thermo-kinetic database that is validated by diffusion couple simulations through Kawin. In conclusion, this enables prediction of microstructural and phase evolution critical for the development and lifetime assessment of next generation nuclear fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Hot Hydrogen Exposure of U x Zr 1-x C y Nuclear Fuel: The Influence of Composition and Density

Refractory carbide nuclear fuel has been one of the most promising fuel candidates for space nuclear propulsion due to its high melting point, temperature stability, and compatibility in a hot hydrogen environment. In this study, U x Zr 1-x C y fuel was produced by means of a carbothermic reduction process in different UC compositions including 5,10, 20, and 30 at.% UC in the fuel compound. The powder feedstock was consolidated via direct current sintering with densities up to 97% of the theoretical density. The samples with different U x Zr 1-x C y compositions were exposed to hot hydrogen at 2600 K for a cumulative time of 300 min. The samples were characterized by SEM, XRD, density, and measured for mass losses. The high-density samples displayed improved performance in hot hydrogen by minimizing porous sites and reducing areas of direct contact with hydrogen gas, leading to reduced mass losses. Variations in sample density proved to induce large changes in mass loss rates, increasing them up to 90%. The compositions with higher UC content reported the largest mass losses in the study. The loss of uranium occurred primarily at the surfaces exposed to the hot hydrogen where changes in the lattice constant confirmed losses exceeding 50% of the initial UC content in higher compositions, specifically to U 0.3 Zr 0.7 C y . XRD analyses revealed the presence of UH 3 in U 0.3 Zr 0.7 C y suggesting that metallic uranium formed inside the sample as a product of carbon losses. High-density U x Zr x-1 C y fuel with UC concentrations at or below 20 at.% UC exhibited stability and negligible density changes in a high temperature hydrogen environment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2011

Phase equilibrium and intermediate phases in the Eu-Sb system

Rapid heating rate thermal analysis, X-ray diffraction, fluorescence spectrometry, and differential dissolution method were used to study the high-temperature phase equilibrium in the Eu-Sb system within the composition range between 37 and 96 at% Sb. The techniques were effective in determination of the vapor-solid-liquid equilibrium since intermediate phases except Eu{sub 4}Sb{sub 3} evaporated incongruently after melting. A thermal procedure was developed to determine the liquidus and solidus lines of the T-x diagram. Six stable phases were identified: two phases, EuSb{sub 2} and Eu{sub 4}Sb{sub 3}, melt congruently at 1045{+-}10 deg. C and 1600{+-}15 deg. C, the Eu{sub 2}Sb{sub 3}, Eu{sub 11}Sb{sub 10}, Eu{sub 5}Sb{sub 4}, and Eu{sub 5}Sb{sub 3} phases melt incongruently at 850{+-}8 deg. C, 950{+-}10 deg. C, 1350{+-}15 deg. C, and 1445{+-}15 deg. C, respectively. The exact composition shifting of Sb-rich decomposable phases towards Eu{sub 4}Sb{sub 3}, the most refractory compound, was determined. The topology of the Eu-Sb phase diagram was considered together with that of the Yb-Sb system. - Graphical abstract: The high-temperature range of the T-x phase diagram for the Eu-Sb system. Highlights: > The phase relations in the Eu-Sb system were studied over a large composition and temperature scale. > The liquidus and solidus lines of the T-x diagram were well established using effective techniques. > In the system, six binary phases are stable and they melt incongruently except EuSb{sub 2} and Eu{sub 4}Sb{sub 3}. > Incongruent evaporation was found to be typical of all the phases besides Eu{sub 4}Sb{sub 3}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

High-pressure densified solid solutions of alkaline earth hexaborides (Ca/Sr, Ca/Ba, Sr/Ba) and their high-temperature thermoelectric properties

Solid solutions of alkaline earth hexaborides were synthesized and densified by spark plasma sintering at 100 MPa. The high-temperature thermoelectric properties (Seebeck coefficients, electrical and thermal diffusivities, heat capacities) were measured between room temperature and 1073 K. CaB{sub 6}, SrB{sub 6}, BaB{sub 6} and the ternary hexaborides Ca{sub x}Sr{sub 1−x}B{sub 6}, Ca{sub x}Ba{sub 1−x}B{sub 6}, Sr{sub x}Ba{sub 1−x}B{sub 6} (x = 0.25, 0.5, 0.75) are n-type conducting compounds over the whole compositional and thermal ranges. The values of the figure of merit ZT for CaB{sub 6} (ca. 0.3 at 1073 K) were found to be significantly increased compared to earlier investigations which is attributed to the densification process. - Highlights: • Solid solutions of alkaline earth hexaborides were synthesized. • High-temperature thermoelectric properties of mixed calcium borides are excellent. • Spark plasma source densification results in high ZT values. • Borides are rare-earth free and refractory materials.

36 MATERIALS SCIENCE↗
DOE OSTI2017

An isotopic perspective on growth and differentiation of Proterozoic orogenic crust: From subduction magmatism to cratonization

The in situ chemical differentiation of continental crust ultimately leads to the long-term stability of the continents. This process, more commonly known as ‘cratonization’, is driven by deep crustal melting with the transfer of those melts to shallower regions resulting in a strongly chemically stratified crust, with a refractory, dehydrated lower portion overlain by a complementary enriched upper portion. Since the lower to mid portions of continental crust are rarely exposed, investigation of the cratonization process must be through indirect methods. In this study we use in situ Hf and O isotope compositions of both magmatic and inherited zircons from several felsic magmatic suites in the Capricorn Orogen of Western Australia to highlight the differentiation history (i.e. cratonization) of this portion of late Archean to Proterozoic orogenic crust. The Capricorn Orogen shows a distinct tectonomagmatic history that evolves from an active continental margin through to intracratonic reworking, ultimately leading to thermally stable crust that responds similarly to the bounding Archean Pilbara and Yilgarn Cratons.

Johnson, Simon P.↗
DOE OSTI2014

Atom probe study of grain boundary segregation in technically pure molybdenum

Molybdenum, a metal with excellent physical, chemical and high-temperature properties, is an interesting material for applications in lighting-technology, high performance electronics, high temperature furnace construction and coating technology. However, its applicability as a structural material is limited because of the poor oxidation resistance at high temperatures and a brittle-to-ductile transition around room temperature, which is influenced by the grain size and the content of interstitial impurities at the grain boundaries. Due to the progress of the powder metallurgical production during the last decades, the amount of impurities in the current quality of molybdenum has become so small that surface sensitive techniques are not applicable anymore. Therefore, the atom probe, which allows the detection of small amounts of impurities as well as their location, seems to be a more suitable technique. However, a site-specific specimen preparation procedure for grain boundaries in refractory metals with a dual focused ion beam/scanning electron microscope is still required. The present investigation describes the development and successful application of such a site-specific preparation technique for grain boundaries in molybdenum, which is significantly improved by a combination with transmission electron microscopy. This complimentary technique helps to improve the visibility of grain boundaries during the last preparation steps and to evidence the presence of grain and subgrain boundaries without segregants in atom probe specimens. Furthermore, in industrially processed and recrystallized molybdenum sheets grain boundary segregation of oxygen, nitrogen and potassium is successfully detected close to segregated regions which are believed to be former sinter pores. - Highlights: • First study of grain boundary segregation in molybdenum by atom probe • Site-specific preparation technique by FIB and TEM successfully developed • Grain boundary segregation of oxygen, nitrogen and potassium found • Segregation in former sinter-pores detected • Presence of grain boundaries without segregation evidenced.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Controlling homogenization length scales and microstructure in additively manufactured Ti-Ta functionally graded materials

Materials with smooth compositional gradients or functionally grade materials (FGMs) produced via additive manufacturing (AM), enables joining dissimilar materials and optimizing multiple properties in advanced engineering applications. However, as-printed AM microstructures exhibit micro-segregation and solidification defects which, when combined with controlling macroscale gradient properties, complicates necessary post-processing. Here, we use CALPHAD-informed diffusion modelling to design post-processing heat treatments for lightweight to refractory FGMs. Ti-Ta (0 to 85 at. % Ta) FGMs were fabricated using laser-based directed energy deposition AM. Post-processing heat treatments at 1000° C and 1500° C were designed to promote homogenization across specific length scales and experimentally validated. Investigation of chemical segregation and microstructures demonstrated that the length scale of homogenization is controlled as a function of time, temperature, and local composition. Ta-rich regions exhibited incomplete homogenization compared to Ti-rich layers. Unmelted Ta particles were found to completely dissolve at 1500 °C. By controlling cooling rate (200 °C/min), martensitic structures were produced between 14–36 at. % Ta, consistent with martensite-start temperatures calculations, while furnace cooling (2 °C/min) produced α+β morphologies. This work establishes a validated predictive framework for designing post-processing to tailor microstructure and chemical architecture in AM FGMs, facilitating their deployment in demanding environments.

Materials science↗
DOE OSTI2022

Plasmon mediated deposition of Ni on titanium nitride nanoparticles: Applications in enhanced photoreduction of bicarbonate

A suitably designed plasmonic catalyst can provide versatile and energy-efficient strategies to utilize visible light to drive different catalytic reactions. Here we have successfully developed composite plasmonic catalysts by visible-light-induced deposition of popular transition metal nanocatalysts such as Ni and Pt on refractory plasmonic titanium nitride (TiN) nanoparticles. Here, the catalytic properties of the TiN composite nanoparticles were evaluated using the visible light-mediated bicarbonate to formate reduction reaction in the presence of glycerol as the hole-scavenger. Deposition of Ni and Pt nanocatalysts on TiN significantly improves its catalytic efficiency towards the reaction. However, Ni deposited on TiN nanoparticles exhibited better catalytic properties in comparison to that of TiN_Pt composites. The findings of this study can be used to develop stable and efficient visible light-responsive plasmonic composite catalysts which can accelerate different energy extensive reactions.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Viscosity of transient glass-forming melt and its relation to foaming during batch-to-glass conversion

Primary foam, which affects the heat transfer into the glass batch and the final glass quality, occurs when a sufficient quantity of transient glass-forming melt evolves with viscosity low enough to close the open porosity of the reacting glass batch. To better understand how the fraction of transient melt and its viscosity affect the primary foam temperature range, we determined, with x-ray diffraction, the fraction and composition of the transient glass-forming melt in a heated waste glass melter feed as a function of temperature. Then we prepared a set of transient melts that occurred within the foaming temperature interval and measured their viscosities with spindle and falling sphere viscometers. Further, the results agree with the Adam-Gibbs and VFT viscosity-composition models, even for transient melt compositions outside of the models compositional validity range. As silica and other refractory particles dissolved in the predominantly borate transient melt while temperature increased, viscosity increased from the initial value of ~500 Pa s at the onset of foaming (~650°C) to a maximum of ~770 Pa s when silica dissolution was almost complete (~700°C). As temperature increased further, transient melt viscosity decreased to ~220 Pa s (~850°C) when the primary foam collapsed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Zr addition on lattice strains and electronic structures of NbTaTiV high-entropy alloy

We report the room-temperature (RT) deformation behavior for two single-phase body-centered-cubic (BCC) refractory high-entropy alloys (RHEAs), NbTaTiV and NbTaTiVZr, has been comprehensively investigated via in-situ neutron-diffraction experiments. Our work shows that the addition of Zr leads to the transition of mechanical response from ductile to brittle behavior. The results of lattice-strain evolutions obtained from in-situ neutron diffraction for the ductile NbTaTiV RHEA exhibit atypical plastic-deformation behavior, i.e., the reduced plasticanisotropic deformation, leading to an even distribution of the applied stress amongst the grains with different orientations rather than forming stress concentrations in {200}-oriented grains during plastic-deformation. Density functional theory (DFT) analysis shows that NbTaTiVZr has a lower electron density at the Fermi level, larger lattice distortion, and stronger charge transfer, as compared to NbTaTiV, suggesting higher strength and lower ductility in NbTaTiVZr, which are consistent with the current experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mg vacancy and impurity-limited MgO single crystal thermal conductivity

Magnesium oxide (MgO) exhibits one of the highest thermal conductivities among oxides and is widely used as a dielectric material and substrate in semiconductor devices, in refractory applications, and as a promising filler in thermal interface materials for electronics. Its high thermal conductivity may be sensitive to impurity and defects, yet this influence is still uncertain. Here, in this study, the impact of the common impurities, i.e., Al, Ca, Ti, V, Fe, Si, B, Nb, Zr, Na, and K, as well as Mg and O vacancies on phonon scattering and thermal conductivity of MgO is studied using a fully first-principles T-matrix framework. It is found that B, Nb, and Zr impurities, along with Mg vacancies, lead to exceptionally strong reductions in thermal conductivity. By contrast, O vacancies and other impurities have modest to minimal impacts. Leveraging the T-matrix results, we reassess the perturbative, mass-only formalism whose use is pervasive in the literature and show that neglecting bond disorder does not necessarily lead to underestimation: for all transition-metal impurities studied, bond perturbations partially cancel mass disorder, causing the traditional perturbative model to overestimate scattering. We propose a simple modified perturbative expression that incorporates both mass and bond disorder and closely reproduces the T-matrix trends. Our predicted low-temperature trends by including phonon-impurity and phonon-boundary scattering match reasonably well with experiments. This work provides an in-depth study of impurity- and vacancy-limited thermal conductivity of MgO and suggests that reported “high-purity” MgO values have likely not yet reached the intrinsic upper limit, which may be substantially higher.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

Irradiation of ultrasonic sensors and adhesive couplants for application in light water reactor primary loop piping and components

The Electric Power Research Institute (EPRI) Nuclear Sector and US Department of Energy Light Water Reactor Sustainability Program are committed to engaging in research and development endeavors to address materials aging issues specific to long term operation of light water power reactors. To this effect, EPRI launched an industry initiative to develop nondestructive evaluation systems for online monitoring of existing cracks in light water reactor primary coolant loop piping and components. One of the goals of this initiative is to develop a sensor system (or systems) that can determine nondestructively if cracks are growing or arrested and, in the case of the former, to characterize their growth rates. A missing component of this initiative is an experimental assessment of how sensors and adhesive couplants will perform in service when exposed to chronic energetic neutron radiation, particularly at the primary coolant loop hot and cold leg dissimilar metal welds, which join the primary loop piping to the reactor pressure vessel and reside in the vicinity of the reactor core. The objective of this experimental study was to determine how ultrasonic transducers and adhesive couplants perform when exposed to irradiation in a test reactor to simulate and accelerate in-service exposure. Further, to achieve this objective, the signal stability of piezoelectric transducers and performance of adhesive couplants as a function of accumulated fast neutron fluence were characterized by collecting ultrasonic data in-situ during irradiation. Of particular interest were the ultrasonic signal quality and time decay of the amplitude of acoustic reflections as a function of fast neutron fluence. The results of the study showed that, of the 8 transducer/substrate sample assemblies tested, only 3 generated usable ultrasonic signals through the conclusion of the irradiation campaign. It was found that high temperature epoxy tends to ultrasonically couple the sensors to the substrates better than three types of refractory ceramic cements studied, as is supported by post irradiation examination. The results obtained through this experimental study will be utilized in the achievement of the overall goal of development of a sensor system to perform online monitoring of primary loop components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Debonding-on-demand reversible adhesives via heat or light with competitive adhesion strength to conventional epoxy adhesives

Stimuli responsive debonding-on-demand (DoD) reversible adhesives are of great interest for the circular economy. However, the reversible adhesives developed so far often lack competitive adhesion strength in a bonding state. In this work, reversible epoxy adhesives based on Diels–Alder (DA) chemistry were developed and exhibited a competitive adhesion strength (e.g., 12 – 16 MPa of a lap shear strength) to commercial non-reversible epoxy adhesives. The reversible epoxy formulation showed superior thermal stability up to 110°C, and transition to a debonding state in the order of 0.1 MPa at 140°C, consequently, an on/off-type debonding behavior. The transition to a debonding state was attributed to crosslinking density control (e.g., decrease by 33% – 49%) through the reversible DA chemistry and the proximity to the glass transition. Next, for debonding by light stimulus, photothermal refractory plasmonic titanium nitride (TiN) nanoparticles were incorporated in the reversible epoxy, which can generate the required heat for debonding upon exposure to visible light. Photothermal debonding allows for precise debonding at target areas and tunable adhesion strength by controlling the exposure area and light intensity. The DA adhesive formulations containing 0.5 wt.% TiN nanoparticles presented a debonding state with zero adhesion under light exposure with intensity of 1670 mW/cm 2 (inducing 140°C). Even after three cycles of reattachment, the DA adhesive formulations retained 96% of the pristine sample’s adhesion strength measured at 110°C. Therefore, the DA adhesives are attractive candidates as reversible DoD systems applicable in higher temperatures.

42 ENGINEERING↗
DOE OSTI2018

Phase transformations of HfNbTaTiZr high-entropy alloy at intermediate temperatures

The strong and ductile single-phase body-centered-cubic (BCC) HfNbTaTiZr refractory high-entropy alloy (RHEA) is a potential structural material for high-temperature applications. However, the BCC phase stability in the intermediate temperature range (500-900 degrees C) needs to be better understood to make this alloy applicable to industry. Here, the phase decomposition of the HfNbTaTiZr RHEA is examined at different temperatures (500-1000 degrees C). Additionally, the formation of BCC Ta-Nb-rich and hexagonal-close-packed (HCP) Hf-Zr-rich precipitates are studied as a function of annealing time at 700 degrees C using a combination of atom probe tomography, transmission electron microscopy, and X-ray diffraction. In conclusion, we found that these BCC and HCP precipitates have preferred orientations with the BCC matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2020

On the quantitative characterization of weld microstructures

Here, a new technique to quantify grain shape and grain boundary curvature in the fusion zone (FZ) and the heat-effected zone (HAZ) of refractory metals and alloys has been developed. The application of this technique to quantify the effect of welding speed on these microstructural characteristics in simulated molybdenum welds is highlighted in this study. A 50% increase in weld speed more than doubles the fraction of grain segments in the fusion zone with orientations between 00 to 300 to the normal to the welding direction, with a corresponding 50% decrease in the fraction of grain segments oriented along the welding direction. This increase in weld speed also results in a reduction in grain size from approximately 120 µm to 84 µm along the WD at the FZ centerline. Grain boundary curvature is negative near the weld centerline and the edge of the fusion zone, indicating that with increasing distance from the weld centerline, the grain segments progressively rotate towards a direction normal to the welding direction at both locations. Presence of regions with relatively straight grain segments indicated by curvatures close to zero were identified in between the weld centerline and the edge of the FZ at all weld speeds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A predictive analytical model of electrical transport in multi-principal-element alloys

A predictive analytical model is presented for the electrical conductivity of multi-principal-element alloys (MPEAs), including those containing aluminum, transition metals, and refractory metals. Given that the lattice parameter of the Wigner-Seitz cell of an MPEA is similarly variable to a bulk metallic glass, it is postulated that electron scattering can be approximated by a series of two-level systems. Here, the resulting reduced-order model enabled an accurate determination of electrical resistivity and electron thermal conductivity based on the scattering of electrons in a two-level system across a Bloch-potential-based virtual crystal approximation. Model results are compared to experimental four-point probe electrical resistivity measurements between 300 K and 700 K for Al 0.3 CoCrCuFeNi, CoCrFeMnNi, (CoCrFeMnNi) 0.98 W 0.02 , (CoCrFeMnNi) 0.95 W 0.05 , and Nb 4 Ta 4 V 3 Ti, for model validation.

Analytical model↗
DOE OSTI2021

Effect of temperature on abrasion erosion in particle based concentrating solar powerplants

The use of solid particles as a heat transfer medium is being explored for concentrated solar power plants (CSP) to increase their efficiency by achieving operating temperature >700 °C. During operation, these hot particles are expected to move along the various components within the collector system, resulting in material degradation from a combination of high-temperature oxidation and erosion. In the present study, the performance of candidate materials was evaluated through a series of abrasion erosion experiments at room temperature as well as at 800 °C. Wear in metallic and refractory type materials was investigated using CarboBead® HSP 40/70 particles inside a resistance heated kiln. Furthermore, cross-sectional scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) analysis on the specimens tested at 800 °C determined that the specific wear rate in Inconel 740H and stainless steel 316 metallic specimens was influenced by the thermally grown oxide morphology. High chromium Inconel 740H specimens exhibited greater resistance to wear with a steady state specific wear rate of 1.92E-4 mm 3 N -1 m –1 compared to 5.7E-3 mm 3 N -1 m –1 for Stainless Steel 316.

14 SOLAR ENERGY↗