Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

SEASAT-A synthetic aperture radar performance

The SEASAT-A satellite synthetic aperture radar (SAR) is presented, and its performance since it began operation in July 1978, is examined. The imaging radar system, the first to be designed as an orbital scientific instrument, was intended to generate continuous imagery over a 100-km swath at 25-m resolution from an altitude of 800 km. SAR image quality is measured in terms of resolution, the range of detectable radar backscatter, and the contrast ratio, each of which is affected by antenna, sensor, data link, and recording/processor subsystem parameters. Microdensitometer scans of output image film of actual SEASAT-A SAR data reveal a range resolution of less than 25 m, an azimuth resolution of approximately 40 m, a noise equivalent dynamic range of from 9.6 to -21 + or - 5 dB, and an image contrast ratio of 7.5 dB. SEASAT-A SAR performance is concluded to have confirmed the utility of spaceborne radar sensing.

Jordan, R. L.↗

Experimental and Numerical Analysis of Additively Manufactured Coupons With Parallel Channels and Inline Wall Jets

Present paper developed a series of additively manufactured parallel cooling channels with streamwise wall jets inside, which could be suitable for double-wall and near-wall cooling configurations in gas turbine hot section components. The tested coupons consisted of parallel channels, each channel further divided into small chambers using several spanwise separation walls. Height of these walls was kept less than channel height, thus forming a slot with one of the end walls. Coolant entered from one side of channel and formed streamwise wall jet while crossing through the slot over to the downstream chamber. The test coupons were additively manufactured by selective laser sintering (SLS) technique using Inconel 718 alloy. Steady-state heat transfer experiments with constant wall temperature boundary condition were performed to analyze effect of pitch between subsequent slots and blockage ratio (ratio of separation wall height to channel height) on heat transfer. The channel Reynolds number ranged from 1800 to 5000. Numerical simulations were performed using ANSYS cfx solver with SST k–ω turbulence model to obtain detailed understanding of existing flow field. Experimental results showed heat transfer enhancement of up to 6.5 times that of a smooth channel for the highest blockage ratio of 0.75. Numerical results revealed complex flow field which consisted of wall jets along with impingement, separation, and recirculation zones in each chamber. For all configurations, gain in heat transfer was accompanied with high pressure drops. However, coupled with the high heat transfer, this design could lead to potential coolant savings.

Engineering↗

Range Performance of Bombers Powered by Turbine-Propeller Power Plants

Calculations have been made to find range? attainable by bombers of gross weights from l40,000 to 300,000 pounds powered by turbine-propeller power plants. Only conventional configurations were considered and emphasis was placed upon using data for structural and aerodynamic characteristics which are typical of modern military airplanes. An effort was made to limit the various parameters invoked in the airplane configuration to practical values. Therefore, extremely high wing loadings, large amounts of sweepback, and very high aspect ratios have not been considered. Power-plant performance was based upon the performance of a typical turbine-propeller engine equipped with propellers designed to maintain high efficiencies at high-subsonic speeds. Results indicated, in general, that the greatest range, for a given gross weight, is obtained by airplanes of high wing loading, unless the higher cruising speeds associated with the high-wing-loading airplanes require-the use of thinner wing sections. Further results showed the effect of cruising at-high speeds, of operation at very high altitudes, and of carrying large bomb loads.

Cline, Charles W.↗

Temperature effect on zinc oxysulfide-Zn(O,S) films synthesized by atomic layer deposition for Cu(In,Ga)Se{sub 2} solar cells

Thin films of Zn(O,S) were deposited by atomic layer deposition from diethylzinc, water (H{sub 2}O), and hydrogen sulfide (H{sub 2}S). First, a study on the influence of the H{sub 2}S/(H{sub 2}O+H{sub 2}S) pulse ratio from pure ZnO to pure ZnS was performed at deposition temperature T{sub dep}=120 and 200 °C. Zn(O,S) films had higher S content than expected, and this effect was stronger at T{sub dep}=200 °C. Then, Zn(O,S) films have been synthesized over the range of temperature 120–220 °C at the constant H{sub 2}S/(H{sub 2}O+H{sub 2}S) pulse ratio of 9%. For T{sub dep}<180 °C, high and almost constant S content has been measured in the films. The significant increase of the S/(O+S) atomic ratio for T{sub dep}>180 °C confirmed that exchange reactions occurred between the Zn(O,S) growing films and H{sub 2}S. The grazing incidence x-ray diffraction patterns showed Zn(O,S) films with hexagonal wurtzite structures and with an optimum crystallization for temperatures T{sub dep}=160–180 °C. Indeed, in this temperature range, well crystallized and large grains were obtained which was in good correlation with the film morphology determined by scanning electron microscope; and Hall effect measurements revealed low resistivities, high carrier concentrations (>10{sup 19} cm{sup −3}), and low mobilities. From these results, the authors propose the existence of a temperature range where the properties undergo significant changes while the atomic composition remains constant.

36 MATERIALS SCIENCE↗

Performance of two-stage fan with larger dampers on first-stage rotor

The performance of a two stage, high pressure-ratio fan, having large, part-span vibration dampers on the first stage rotor is presented and compared with an identical aerodynamically designed fan having smaller dampers. Comparisons of the data for the two damper configurations show that with increased damper size: (1) very high losses in the damper region reduced overall efficiency of first stage rotor by approximately 3 points, (2) the overall performance of each blade row, downstream of the damper was not significantly altered, although appreciable differences in the radial distributions of various performance parameters were noted, and (3) the lower performance of the first stage rotor decreased the overall fan efficiency more than 1 percentage point.

Urasek, D. C.↗

Development of a Ground-Based Analog to the Advanced Resistive Exercise Device Aboard the International Space Station

NASA and Wyle engineers constructed a Horizontal Exercise Fixture (HEF) that was patented in 2006. Recently modifications were made to HEF with the goal of creating a device that mimics squat exercise on the Advanced Resistive Exercise Device (ARED) and can be used by bed rest subjects who must remain supine during exercise. This project posed several engineering challenges, such as how best to reproduce the hip motions (we used a sled that allowed hip motion in the sagittal plane), how to counterweight the pelvis against gravity (we used a pulley and free-weight mechanism), and how to apply large loads (body weight plus squat load) to the shoulders while simultaneously supporting the back against gravity (we tested a standard and a safety bar that allowed movement in the subject s z-axis, both of which used a retractable plate for back support). METHODS An evaluation of the HEF was conducted with human subjects (3F, 3M), who performed sets of squat exercises of increasing load from 10-repetition maximum (RM) up to 1-RM. Three pelvic counterweight loads were tested along with each of the two back-support squat bars. Data collection included 3-dimensional ground reaction forces (GRF), muscle activation (EMG), body motion (video-based motion capture), and subjective comments. These data were compared with previous ground-based ARED study data. RESULTS All subjects in the evaluation were able to perform low- to high-loading squats on the HEF. Four of the 6 subjects preferred a pelvic counterweight equivalent to 60 percent of their body weight. Four subjects preferred the standard squat bar, whereas 2 female subjects preferred the safety bar. EMG data showed muscle activation in the legs and low back typical of squat motion. GRF trajectories and eccentric-concentric loading ratios were similar to ARED. CONCLUSION: Squat exercise performed on HEF approximated squat exercise on ARED.

Newby, Nathaniel J.↗

Simulation of image detectors in radiology for determination of scatter-to-primary ratios using Monte Carlo radiation transport code MCNP/MCNPX

Purpose: The purpose of this study was to compare and validate three methods to simulate radiographic image detectors with the Monte Carlo software MCNP/MCNPX in a time efficient way. Methods: The first detector model was the standard semideterministic radiography tally, which has been used in previous image simulation studies. Next to the radiography tally two alternative stochastic detector models were developed: A perfect energy integrating detector and a detector based on the energy absorbed in the detector material. Validation of three image detector models was performed by comparing calculated scatter-to-primary ratios (SPRs) with the published and experimentally acquired SPR values. Results: For mammographic applications, SPRs computed with the radiography tally were up to 44% larger than the published results, while the SPRs computed with the perfect energy integrating detectors and the blur-free absorbed energy detector model were, on the average, 0.3% (ranging from -3% to 3%) and 0.4% (ranging from -5% to 5%) lower, respectively. For general radiography applications, the radiography tally overestimated the measured SPR by as much as 46%. The SPRs calculated with the perfect energy integrating detectors were, on the average, 4.7% (ranging from -5.3% to -4%) lower than the measured SPRs, whereas for the blur-free absorbed energy detector model, the calculated SPRs were, on the average, 1.3% (ranging from -0.1% to 2.4%) larger than the measured SPRs. Conclusions: For mammographic applications, both the perfect energy integrating detector model and the blur-free energy absorbing detector model can be used to simulate image detectors, whereas for conventional x-ray imaging using higher energies, the blur-free energy absorbing detector model is the most appropriate image detector model. The radiography tally overestimates the scattered part and should therefore not be used to simulate radiographic image detectors.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

ZnO Nanorod Thermoplastic Polyurethane Nanocomposites: Morphology and Shape Memory Performance

The impact of dispersed alkylthiol-modified ZnO nanorods, as a function of rod aspect ratio and concentration, on the shape memory character of a thermoplastic polyurethane with low hard-segment density (LHS-TPU) is examined relative to the enhanced performance occurring for carbon nanofiber (CNF) dispersion. Solution blending resulted in uniform dispersion within the LHS-TPU of the ZnO nanorods at low volume (weight) fractions (<2.9% v/v (17.75% w/w)). Tensile modulus enhancements were modest though, comparable to values observed for spherical nanofillers. Shape memory characteristics, which in this LHS-TPU result when strain-induced crystallites retard the entropic recovery of the deformed chains, were unchanged for these low volume fraction ZnO nanocomposites. Higher ZnO loadings (12% v/v (50% w/w)) exhibited clustering of ZnO nanorods into a mesh-like structure. Here, tensile modulus and shape recovery characteristics were improved, although not as great as seen for comparable CNF addition. Wide angle X-ray diffraction and NMR revealed that the addition of ZnO nanorods did not impact the inherent strain induced crystallization of the LHS-TPU, which is in contrast to the impact of CNFs and emphasizes the impact of interactions at the polymer-nanoparticle interface. Overall, these findings reinforce the hypothesis that the shape memory properties of polymer nanocomposites are governed by the extent to which nanoparticle addition, via nanoparticle aspect ratio, hierarchical morphology, and interfacial interactions, impacts the molecular mechanism responsible for trapping elastic strain.

36 MATERIALS SCIENCE↗

An Investigation of a Mixer-Ejector Nozzle for Jet Noise Reduction

An experimental study is conducted assessing the performance of an ejector together with an 8:1 aspect ratio rectangular nozzle with the eventual goal of noise reduction for jet engines. Wall static pressure and Pitot probe surveys are conducted to evaluate the performance of the ejector, and sound pressure level measurements are made to assess the impact on noise radiation. It is found that addition of vortex generating tabs at the lip of the nozzle causes large increases in secondary flow entrainment. The baseline ejector (without tabs) often encounters flow resonance with accompanying tones. The tabs have the additional benefit of eliminating those tones. In most cases tried so far, pockets of high-speed fluid remain unmixed. Since jet noise scales as velocity to the eighth power, such ‘hot spots’ defeat the noise reduction goal. In some cases, there is a reduction in noise amplitudes in the mid-frequency range (5-30 kHz), however, an increase occurs on the low frequency end apparently due to flow unsteadiness. This together with a high frequency noise increase caused by the tabs results in minimal reductions in the overall sound pressure level. The focus of ongoing and future efforts is to achieve sufficient mixing and desirable noise reduction while keeping the hard-ware short and lightweight.

Zaman, K. B. M. Q.↗

Designing Ground Antennas for Maximum G/T: Cassegrain or Gregorian?

For optimum performance, a ground antenna system must maximize the ratio of received signal to the receiving system noise power, defined as the ratio of antenna gain to system-noise temperature (G/T). The total system noise temperature is the linear combination of the receiver noise temperature (including the feed system losses) and the antenna noise contribution. Hence, for very low noise cryogenic receiver systems, antenna noise-temperature properties are very significant contributors to G/T.It is well known that, for dual reflector systems designed for maximum gain, the gain performance of the antenna system is the same for both Cassegrain and Gregorian configurations. For a12-meter antenna designed to be part of the large array based Deep Space Network, a Cassegrain configuration designed for maximum G/T at X-band was 0.7 dB higher than the equivalent Gregorian configuration. This study demonstrates that, for maximum GIT, the dual shaped Cassegrain design is always better than the Gregorian.

ground antennas↗

Experimental Investigation of Sweeping Jet Film Cooling in a Transonic Turbine Cascade

Abstract The sweeping jet (SJ) film cooling hole has shown promising cooling performance compared to the standard shaped hole in low-speed conditions. The present work demonstrates the first attempt of SJ film cooling at an engine relevant Mach number. An experimental investigation was conducted to study the SJ film cooling on a nozzle guide vane suction surface. A well-established additive manufacturing technique commonly known as stereolithography (SLA) was utilized to design a transonic, engine representative vane geometry in which a row of SJ holes was used on the vane suction surface. Experiments were performed in a linear transonic cascade at an exit Mach number of 0.8 and blowing ratios of BR = 0.25–2.23. The measurement of heat transfer was conducted with the transient IR method, and the convective heat transfer coefficient (HTC) and adiabatic film cooling effectiveness were estimated using a dual linear regression technique (DLRT). Aerodynamic loss measurements were also performed with a total pressure Kiel probe at 0.25Cax downstream of the exit plane of the vane cascade. Experiments were also conducted for a baseline-shaped hole (777-hole) for a direct comparison. Results showed that the SJ hole has a wider coolant spreading in the lateral direction near the hole exit due to its sweeping motion that improves the overall cooling performance particularly at high blowing ratios (BR > 1). Aerodynamic loss measurement suggested that the SJ hole has a comparable total pressure loss to the 777-shaped hole.

Engineering↗

Investigation of High-Subsonic Performance Characteristics of a 12 Degree 21-Inch Conical Diffuser, Including the Effects of Change in Inlet-Boundary-Layer Thickness

Investigations were conducted of a 12 degree 21-inch conical diffuser of 2:l area ratio to determine the interrelation of boundary layer growth and performance characteristics. surveys were made of inlet and exit from, longitudinal static pressures were recorded, and velocity profiles were obtained through an inlet Reynolds number range, determined From mass flows and based on inlet diameter of 1.45 x 10(exp 6) to 7.45 x 10(exp 6) and a Mach number range of 0.11 to approximately choking. These investigations were made to two thicknesses of inlet boundary layer. The mean value, over the entire range of inlet velocities, of the displacement thickness of the thinner inlet boundary layer was approximately 0.035 inch and that of the thicker inlet boundary layer was approximately six times this value. The loss coefficient in the case of the thinner inlet boundary layer had a value between 2 to 3 percent of the inlet impact pressure over most of the air-flow range. The loss coefficient with the thicker inlet boundary layer was of the order of twice that of the thinner inlet boundary layer at low speeds and approximately three times at high speeds. In both cases the values were substantially less than those given in the literature for fully developed pipe flow. The static-pressure rise for the thinner inlet boundary layer was of the order of 95 percent of that theoretically possible over the entire speed range. For the thicker inlet boundary layer the static pressure rise, as a percentage of that theoretically possible, ranged from 82 percent at low speeds to 68 percent at high speeds.

Copp, Martin R.↗

Enhanced Performance of Dual Inverter with a Floating Capacitor for Motor Drive Applications

This paper studies a dual inverter supplied by a DC-link and a floating capacitor (FC), emerged as a promising inverter topology for motor drive applications. For this type of inverter, the voltage ratio between the DC-link and the FC can be actively controlled. This ratio design is crucial as it essentially defines both the DC-link voltage utilization and the inverter output quality. Several voltage ratios have previously been discussed to enhance the dual inverter performance, but only one aspect, either the voltage utilization or the output quality, is investigated. As a result, although one performance aspect can be improved, the other aspect has been adversely affected. In this work, a comparative study considering both aspects is carried out for all the possible voltage ratios. Based on this analysis, the optimal ratios for different inverter modulation indices are identified. This is followed by proposing a ratio selection strategy to double the voltage utilization without degrading the output quality. Furthermore, this strategy enables an electric drive to work at a higher maximum speed without flux weakening for a given DC-link voltage. The claimed advantages have been proved by experimental tests on an open-end windings induction motor drive.

42 ENGINEERING↗

Electron-density-sensitive Line Ratios of Fe XIII--XVI from Laboratory Sources Compared to CHIANTI

We present electron-density-sensitive line ratios for Fe XIII–XVI measured in the spectral wavelength range of 200–440 Å and an electron density range of (1–4)×10 13 cm -3 . The results provide a test at the high-density limit of density-sensitive line ratios useful for astrophysical studies. The measurements were performed on the National Spherical Torus Experiment-Upgrade, where electron densities were measured independently by the laser Thomson scattering diagnostic. Spectra were collected with a flat-field grazing-incidence spectrometer, which provided a spectral resolution of up to 0.3 Å, i.e., high resolution across the broad wavelength range. The response of the instrument was relatively calibrated using spectroscopic techniques in order to improve accuracy. The line ratios are compared to other laboratory sources and the latest version of CHIANTI (8.0.2), and an agreement within 30% is found.

Spectroscopic techniques↗

High speed demodulation systems for fiber optic grating sensors

Fiber optic grating sensor demodulation systems are described that offer high speed and multiplexing options for both single and multiple parameter fiber optic grating sensors. To attain very high speeds for single parameter fiber grating sensors ratio techniques are used that allow a series of sensors to be placed in a single fiber while retaining high speed capability. These methods can be extended to multiparameter fiber grating sensors. Optimization of speeds can be obtained by minimizing the number of spectral peaks that must be processed and it is shown that two or three spectral peak measurements may in specific multiparameter applications offer comparable or better performance than processing four spectral peaks. Combining the ratio methods with minimization of peak measurements allows very high speed measurement of such important environmental effects as transverse strain and pressure.

Udd, Eric↗

Performance comparison of a lobed-daisy mixer nozzle with a convergent nozzle at subsonic speeds

An investigation to determine the performance, in terms of thrust minus nozzle axial force, of a lobed-daisy mixer nozzle has been conducted in a 16-foot transonic tunnel at static conditions and at Mach numbers from 0.40 to 0.90 at angles of attack from 4 minus to 8. Jet-total-pressure ratio was varied from about 1.2 to 2.0. The performance of a reference convergent nozzle with a similar nozzle throat area and length was used as a base line to evaluate the performance of the lobed-daisy mixer nozzle. The results of this investigation indicate that with no external airflow (Mach number M of 0), and at values of jet-total-pressure ratio between 1.2 and 2.0, the static thrust exerted by the lobed-daisy mixer nozzle is less than that of the convergent nozzle by about 10 percent of ideal gross thrust. About 3.4 percent of the thrust loss was attributed to an unintentional internal area expansion in the fan passage.

Maiden, D. L.↗

Using geochemical indicators to distinguish high biogeochemical activity in floodplain soils and sediments, Science of the Total Environment: Dataset

Data associated with analysis of sediment samples collected in the East River watershed and Rifle floodplain sites, CO. Samples were collected and analyzed as part of two student MS theses at Colorado School of Mines (Kenwell and Prugue) over a time period ranging from 2012 to 2015. Analyses include total organic carbon, leachable Fe and Mn, and total microbial DNA; all analyses performed at Colorado School of Mines. Methods: Samples were collected from core during a drilling campaign at the Rifle Site. Samples were collected every 1.5 m. At the East River site soil and sediment samples were collected using hand-augered bulk density sampler. Collected samples were stored at -20C until analysis. Samples were thawed in an anaerobic chamber and subsampled for extractions and DNA analysis. Samples for DNA analysis were freeze-dried, the remaining sample was oven dried and ground to 0.991 cm for TOC and leaching analysis. TOC analysis was performed on duplicate samples using a CM 5014 Coulometer (UIC, Joliet, IL, USA). Two chemical extractions were performed: hydroxylamine (HA) extraction of Fe and Mn adapted from Lovley et al., 1987 and synthetic precipitation (ppt) leaching adapted from EPA method 1312 (EPA, 1994) . For theHA extraction 3g of wet sediment was mixed with 150 mL of 0.5 N HCl in one bottle and another 3 g of sediment was mixed with 150 mL of 0.25 N hydroxylamine hydrochloride in 0.5 N HCl. Extraction were performed for 24 hours at room temperature after which samples of the liquid were removed and filtered to 0.45 micron and analyzed by ICP-AES. HA-reducible iron and manganese concentrations were determined by difference between the two extractions. For ppt leaches, a 60:40 sulfuric:nitric acid mixture was added to Milliq water to a pH of 4.2 and combined with sediment in a 20:1 mass ratio of acid to sediment. The extraction was performed for 18 hours at room temperature after which the samples of the liquid were removed and filtered to 0.45 micron and analyzed by ICP-AES. DNA was sampled from sediment using a PowerSoil DNA Isolation Kit and extractions were performed according to manufactured instuctions with one adjustment, a 1 minute bead beating replaced the 10 minute vortexing step. Extracted DNA was stored at -20C. Quantitative PCR was performed in triplicate on a Roche LightCycler 480 system and working curves were created by amplifying environmental samples with primers and bead purifying them with Agencourt AMPure XP. Analysis was performed with a Qubit 2.0 Fluorometer and Qubit dsDNA High Sensitivity Assay Kit with results converted to copies using the URI Genomics and Sequencing Center converter (Staroscik, 2004). Additional method details can be found in Kenwell et al., 2016. Lovley, D.R., Phillips, E.J.P. (1987). Rapid assay for microbially reducible ferric iron in aquatic sediments. Applied and Environmental Microbiology, 53(7), 1536-1540. Staroscik, A. (2004). Calculator for determining the number of copies of a template. URI Genomics & Sequencing Center. <http://cels.uri.edu/gsc/cndna.html>. EPA. (1994). Method 1312: Synthetic precipitation leaching procedure.

54 ENVIRONMENTAL SCIENCES↗

Electron-density-sensitive Line Ratios of Fe xiii– xvi from Laboratory Sources Compared to CHIANTI

We present electron-density-sensitive line ratios for Fe xiii– xvi measured in the spectral wavelength range of 200–440 Å and an electron density range of (1-4) × 10 13 cm -3 . The results provide a test at the high-density limit of density-sensitive line ratios useful for astrophysical studies. The measurements were performed on the National Spherical Torus Experiment-Upgrade, where electron densities were measured independently by the laser Thomson scattering diagnostic. Spectra were collected with a flat-field grazing-incidence spectrometer, which provided a spectral resolution of up to 0.3 Å, i.e., high resolution across the broad wavelength range. The response of the instrument was relatively calibrated using spectroscopic techniques in order to improve accuracy. Lastly, the line ratios are compared to other laboratory sources and the latest version of CHIANTI (8.0.2), and an agreement within 30% is found.

79 ASTRONOMY AND ASTROPHYSICS↗