Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Microstructure and texture evolution of friction stir lap welded dissimilar multi-aluminum stack

Here this work investigates the microstructural evolution of a dissimilar multiple-aluminum alloy stack (AA7055, AA7055, AA6022) produced by friction stir lap welding (FSLW). A through-thickness analyses of grain orientation map, grain size and distribution, strain distribution, and texture evolution by electron backscattered diffraction-based characterization technique were performed. Two different welding parameters (combination of tool rotation and traverse speed) were used to study the effects of the welding parameters on these microstructural characteristics. The study shows that higher welding speed and higher rotation speed of the FSLW tool yield finer grains. FSLW resulted in shear texture formation in the weld regions due to high welding speeds. This texture development in the nugget zone is consistent with shear deformation, and (111) pole figures show ideal shear texture components. The Stir Zone (SZ) exhibits shear texture (A/A ̅ and B/B ̅ components), consistent with other shear-assisted processes. Recrystallization mechanisms observed are CDRX in SZ and DDRX in TMAZ (Thermo-Mechanically Affected Zone). Interface analysis reveals the presence of oxide layers between different aluminum sheets, affecting joint mechanical performance. The mechanical property of the lap welded joints was presented in terms of microhardness distribution across the weld cross section. Slightly higher hardness in higher speed welding setup was observed throughout the SZ and AA6022 layer, indicating greater grain refinement and uniform grain structure distribution.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elucidating microstructural evolution and hardness variation across friction self-piercing riveted Al-7055 using synchrotron X-ray scattering and advanced microscopy techniques

Friction self-piercing riveting (FSPR) is a unique hybrid joining technique that combines the advantages of mechanical interlocking, frictional heat, and solid-state joining (if metallurgically compatible) to produce crack free joints in high strength and/or low-ductility alloys at room temperature. Here, in the current study, Al-7055 sheets were joined using FSPR for lightweight automotive applications and significant microhardness variations were observed across the joint cross-section. A detailed microstructural characterization at multiple length scales was carried out using advanced electron microscopy and X-ray scattering techniques to provide a fundamental understanding of the process-structure-property relationships. The relative contributions of microstructural characteristics at various length scales (i.e., grain size, dislocation density, solute concentration, precipitate nature) to strengthening were estimated using existent formulations (i.e., Hall-Petch, Taylor, precipitate bypass/shear equations) and correlated to the observed microhardness values across different regions. Small-angle X-ray scattering and scanning transmission electron microscopy revealed significant changes in the size and volume fraction of precipitate species, i.e., GP-I Zones, η′, and Mg/Zn solute co-clusters, depending on the process region. It was observed that the dissolution of the small η′/GP-I zones (T ∼ 150–200 °C) in the heat-affected zone were the key reason for the hardness drop. Further, it was shown that solid-solution, dislocation, grain size and solute co-cluster strengthening played a key role in the thermo-mechanically affected zone and grain-refined zone (GRZ). Finally, these observations were leveraged along with the Zener-Holloman relationship and grain size in the GRZ to estimate the peak joining temperature of the GRZ (∼ 350 °C) near the steel rivet.

aluminum 7xxx alloy↗
DOE OSTI2022

Microstructural and physicochemical origins of electroless copper deposition on graphite enhanced by acid pretreatment

We report Acid treatment is the most widely used surface modification method for enhancing the electroless metal deposition (EMD) on carbon reinforcement materials (CRMs) for metal matrix nanocomposites. However, specific microstructural and physicochemical origins of the enhanced EMD on carbon surfaces by acid treatments have been rarely studied. Here, we investigated the effects of the nitric acid treatment on graphite, a prototypical combination of acid treatment and CRM, on the fidelity of Cu EMD and their structural and chemical origins. Complementary materials characterizations and density functional theory calculations revealed the acid-induced formation of broken C–C/C=C graphitic bonds and resulting surface micropores on graphite; this enabled a uniform dispersion of catalytic Sn/Pd nanoparticles during pre-EMD sensitization/activation processes via spontaneous binding of Sn and Pd ions and, consequently, a much more uniform Cu layer EMD compared to the untreated graphite. We proposed a general mechanism illustrating how the acid-induced microstructural and chemical modifications of carbon surface affected the spatial uniformity of catalytic metal reduction during EMD and, finally, the quality of deposited metal layer. The results clearly reveal the origins of the enhanced EMD on carbon materials by acid treatments, providing guidelines for optimizing EMD on general CRMs for high-performance metal matrix nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of laser power on defect, texture, and microstructure of a laser powder bed fusion processed 316L stainless steel

The effect of laser power on defect characteristics, microstructure development, constituent phases, and crystallographic texture was studied on a laser powder bed fusion (L-PBF) processed 316L stainless steel. A series of cylindrical specimens were additively manufactured as a function of laser power ranging from 380 to 200W with a fixed scan speed of 300 mm/s using a selective laser melting system. The density (in terms of count, surface area, and porosity), size (mean values of major axis length, surface area, and volume), shape (aspect ratio and sphericity), and orientation (in terms of the angle between the major axis and build direction) of macroscopic defects in as-printed L-PBF cylinders were characterized using high-resolution synchrotron x-ray computed microtomography with a 0.65μm resolution. Moreover, the changes in the preferred crystallographic orientations and constituent phases were investigated using high-energy synchrotron x-ray diffraction. Finally, the melt pool shape and grain size/orientation were analyzed using metallography. The results show that the porosity increases linearly from 0.13 to 0.88% with the decrease in laser power. However, even with the decrease in laser power by about half and corresponding seven-fold increase in porosity, the 200W case can still be considered as nearly fully dense. On the other hand, with the same decrease in the laser power, the melt pool size/shape, grain size, and texture changed significantly. In conclusion, the role of energy input in the simultaneous changes in defect properties and microstructure development will be discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of laser scanning speed on the microstructure, phase transformation and mechanical property of NiTi alloys fabricated by $\mathrm{LPBF}$

This study investigated the effects of laser scanning speed on the microstructure, phase transformation and properties of NiTi alloys fabricated by laser powder bed fusion (LPBF). In this study, the contributions of metallurgical factors under different scanning speeds, such as Ni evaporation, Ni4Ti3 precipitation, dislocations and internal stress, to the transformation temperature and transformation latent heat were clarified through specially designed experiments. Ni evaporation is found to have the most profound effect, followed by precipitation. Increasing scanning speed is found to reduce Ni loss, thus cause less increase in the transformation temperature and transformation heat of the LPBF-NiTi alloys. Increasing scanning speed also increases the microstructure non-uniformity and thus widens the transformation temperature interval. The orientations of residual stress exhibit strong crystallographic stiffness dependence. The LPBF-NiTi alloys with different scanning speeds all exhibited high strains (>13.4%) and excellent shape memory effect. A LPBF-NiTi honeycomb structure exhibited 96% shape recovery rate after a 60% pre-compressive deformation. Besides, there is an optimum scanning speed for minimum porosity and smallest average pore size. However, the pore structure is found to have weak influence on the tensile behaviour of the LPBF-NiTi alloys, possibly due to the high defect tolerance of the martensitic transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Quantification of solution annealing effects on microstructure and property in a laser powder bed fusion 316H stainless steel

Solution annealing (SA) is an effective way to mitigate microstructural heterogeneity and to optimize mechanical performance of alloys manufactured by laser powder bed fusion (LPBF). In this study, a comprehensive and quantitative understanding of the recovery and recrystallization processes in the SA temperature range of LPBF 316H stainless steel is provided using results from analytical electron microscopy and in-situ high-energy synchrotron x-ray scattering. The profound effect of dislocation structures and secondary phase particles on mechanical performance, particularly under tension and creep conditions, is rationalized using deformation models that incorporate microstructural inputs. This study, for the first time, quantifies the broad effect of nano oxide inclusions on dislocation recovery kinetics, on grain growth and recrystallization kinetics, and on tension strength and creep resistance. The fundamental differences between the LPBF and the conventional wrought materials are revealed. The findings address critical questions in post-build processing of AM materials and pave the way for their rapid qualification for high temperature applications.

In-situ X-ray diffraction↗
DOE OSTI2018

Investigation on microstructures and phase transition characteristics of titanium/yttrium co-doped vanadium oxide thin films

Highlights: • Conjugated interaction between Ti{sup 4+} and Y{sup 3+} ions has been observed in Ti/Y codoped VO{sub 2} films. • The conjugated interaction causes the appearance of VO{sub 2} (B), even complete amorphization in Ti/Y co-doped VO{sub 2} thin film. • Ti/Y co-doping restrains the SMT feature of VO{sub 2} films. - Abstract: Co-doping with two elements has recently attracted attention as a novel approach for tailoring the semiconductor-metal transition (SMT) characteristics of vanadium dioxide (VO{sub 2}). Here, we investigate the influence of titanium/yttrium (Ti/Y) co-doping on the microstructure and SMT characteristics of VO{sub 2} thin films. At low Y concentration, Ti/Y co-doped VO{sub 2} thin films exhibit a monoclinic structure similar to VO{sub 2} but characterized by a smaller grain size, whereas, the VO{sub 2}(B) phase appears as the Y concentration is increased. Interestingly, even a complete amorphization of the film is obtained for co-doped VO{sub 2} thin films. The strong dependence of the microstructure upon the co-doping level is ascribed to the conjugated influence from the simultaneous adjustment of VV chains and VO bonds due to the existence of Ti{sup 4+} and Y{sup 3+} ions in VO{sub 2} lattice, respectively. As a result, the SMT feature of VO{sub 2} thin films is strongly limited or even fully disappears.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Theoretical and experimental demonstration of the relationship between microstructure and the DC-bias-superposition characteristic of ferrite materials

Highlights: • We proved how to improve DC-bias-superposition characteristic of ferrites. • We confirmed the correctness of the theoretical result by experiment. • This research provides a good guide for developing more stable ferrites. - Abstract: DC-bias superposition is important for ferrite materials used in power components. However, methods of improving this characteristic of ferrites have not yet been clearly established. In this study, we theoretically prove that a ferrite with high intrinsic permeability composition and thick grain-boundary microstructure provides better DC-bias superposition than a ferrite with low intrinsic-permeability composition and thin grain-boundary microstructure given the same permeability. We then validate the theoretical results by experiments. Results can guide the development of ferrite materials while considering permeability and stability for the improvement of DC-bias superposition.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Effects of Cold Rolling on Microstructure and Mechanical Properties of Fe-30Mn-3Si-4Al-0.093C TWIP Steel

The effects of cold rolling on microstructure evolution and the associated mechanical properties of Fe-30Mn-3Si-4Al-0.093C twinning-induced plasticity (TWIP) steel are examined in this work with reduction rates of 10%, 20%, 30%, 40%, 50%, 60%, and 70%. Through texture analysis and transmission electron microscopy (TEM) observations, it is suggested that slip, mechanical twinning, the interaction between dislocation/twin boundaries (TB), and shear band have influenced the observed mechanical behavior and development of texture. Special components of weak initial textures are preferential for mechanical twinning, resulting in an increase in strain hardening rate. By mechanical twinning, the {111}<112> orientation is rotated into a position at the vicinity of the {110}<001> Goss orientation, and the {552}<115> (Cu-twin) texture is transformed to the {110}<001> orientation. The evolution of texture is closely related to the onset of shear banding resulting from deformation twinning. The sample with 10% cold reduction exhibits a favorable combination of yield strength and ductility, indicating a considerable capacity for energy absorption. With increasing rolling reductions, the deformation of the samples becomes inhomogeneous due to the high anisotropy of the microstructure. The localized shear bands resulting from the excessive cold rolling are detrimental to the ductility of the present TWIP steel.

Shen, Yongfeng↗
DOE OSTI2015

Effect of cold rolling on the microstructure and mechanical properties of Al 0.25 CoCrFe 1.25 Ni 1.25 high-entropy alloy

Cold rolling can break down the as-cast dendrite microstructure and thus may have pronounced impact on the mechanical behavior of the alloy. In the present study, the effect of cold rolling on the microstructure and mechanical properties of Al 0.25 CoCrFe 1.25 Ni 1.25 high-entropy alloy in the face-centered cubic structure was investigated. With increasing the thickness reduction from cold rolling, the hardness, the yield strength, and the fracture strength increased at the cost of reducing ductility. At the thickness reduction of 80%, the tensile strength (hardness) was 702 MPa (406 MPa), 1.62 (2.43) times that in the as-cast condition. Compared to traditional alloys, Al 0.25 CoCrFe 1.25 Ni 1.25 has the highest hardening rate with respect to CR thickness reduction. Lastly, the phase relation and the mixing properties of Gibbs free energy, enthalpy and entropy of Al x CoCrFe 1.25 Ni 1.25 were predicted using the CALPHAD method.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment

Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesis, microstructure and micro-mechanical characterization of metal (Nb, Ti) – MAX phase (Ti 2 AlC) nanolaminates

We utilize elevated temperature physical vapor deposition (PVD) techniques to design metal/MAX multilayered nanocomposite thin films with alternating nanoscale metallic (Nb, Ti) and MAX phase (Ti 2 AlC) layer thicknesses. These metal/MAX nanolaminate architectures attempt to exploit a unique hierarchical topology – as interfaces between the layers are expected to be in direct competition with the internal interfaces within the MAX layers, to drive their tunable macroscopic mechanical behavior. Two metal/MAX nanolaminates – Nb/Ti 2 AlC and Ti/Ti 2 AlC – were deposited. The Nb/Ti 2 AlC metal/MAX system showed highly diffused layer interfaces with distinct Ti – rich and Nb–Al – rich layers, with the presence of MAX phase alongside TiC and other Ti–Al and Nb–Al intermetallic phases. The Nb/Ti 2 AlC system possessed a layered architecture, though the MAX phases were not found to be continuously present in each alternating layer. The second Ti/Ti 2 AlC system showed a non-lamellar nanocomposite microstructure and the formation of mixed Ti n+1 AlC n phases (a mix of n = 1, 2), and no indication of layering. Diffusion occurring between the metal/MAX layers in both cases, likely due to the elevated temperatures during the deposition process, is speculated as the likely cause of these resultant microstructures. The mechanical properties of both systems were evaluated using micromechanical (nanoindentation and micro-pillar compression) techniques, which demonstrated high strengths for both systems (Nb system: yield and instability strengths of 4.88 ± 0.1 GPa and 5.57 ± 0.03 GPa, Ti system: yield and instability strength of 5.61 ± 0.28 GPa and 6.21 ± 0.25 GPa). In conclusion, this work highlights the promising mechanical properties of metal/MAX multilayered depositions and summarizes the challenges in PVD synthesis of metal/MAX multilayered nanolaminates.

MAX phase↗
DOE OSTI2024

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2020

Influence of scan strategy on porosity and microstructure of Ti-6Al-4V fabricated by electron beam powder bed fusion

Ti-6Al-4V is of high value in biomedical, aerospace, and industrial sectors and is ideal for additive manufacturing (AM) because of its poor machinability. In electron beam powder bed fusion of Ti-6Al-4V, a raster scan is commonly used and often results in porosity that is detrimental to the fatigue strength. In this paper, we demonstrate that spot melting can significantly minimize porosity but produces a coarser microstructure compared to raster melting. Process parameters can be optimized to achieve minimal porosity with tailored microstructures. A finite element method was used to rationalize these observations.

36 MATERIALS SCIENCE↗