Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93

Electronic states at the interface between indium tin oxide and silicon

Electronic properties and thermal stability of interfacial states between indium tin oxide (ITO) and monocrystalline silicon (Si) have been investigated. ITO films with thicknesses of about 300 nm were deposited by dc magnetron sputtering on n- and p-type (100) Si at room temperature. The samples were then annealed for 30 min at different temperatures in the range 100-600 deg. C, and the ITO-Si junction was found to exhibit rectifying behavior. Current-voltage (IV), capacitance-voltage (CV), and deep-level transient spectroscopy (DLTS) measurements have been used to electrically characterize the ITO-Si interface. DLTS measurements on p-type Si samples reveal a dominant hole trap at around 0.37 eV above the valence band edge. In the n-type samples, a broad band of electron traps occur in the range 0.1-0.2 eV below the conduction band edge. These electron traps display wide DLTS peaks, indicating a band of electronic energy levels rather than well-defined states originating from isolated point defects. All the traps in both the p- and n-type samples are found to be located near the ITO-Si interface. Investigations of the thermal stability of the observed electronic states show that the dominant hole trap anneal out after 30 min at 250 deg. C, while the dominant electron traps can be stable up to 500 deg. C. IV and DLTS measurements demonstrate a clear correlation between the annealing of the dominant electronic states and increase in the junction rectification.

36 MATERIALS SCIENCE↗

Enhanced stability against bias-stress of metal-oxide thin film transistors deposited at elevated temperatures

Transparent zinc-tin-oxide (ZTO) thin film transistors (TFTs) have been prepared by DC magnetron sputtering. Compared to reference devices with a channel deposited at room temperature and subsequently annealing at 400 deg. C, a substantially enhanced stability against bias stress is evidenced for devices with in-situ substrate heating during deposition (400 deg. C). A reduced density of sub-gap defect states in TFT channels prepared with in-situ substrate heating is found. Concomitantly, a reduced sensitivity to the adsorption of ambient gases is evidenced for the in-situ heated devices. This finding is of particular importance for an application as driver electronics for organic light emitting diode displays.

36 MATERIALS SCIENCE↗

Structural, Morphological and Optical properties of Sputtered Nickel oxide Thin Films

Nickel oxide (NiO) thin films have been deposited by dc reactive magnetron sputtering technique on glass substrates at various substrate temperatures in the range of 303 to 723 K. The influence of substrate temperature on structural, morphological, compositional and optical properties was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and spectrophotometer studies. The structural properties of the films were strongly influenced by the substrate temperature. From the microstructural studies, fine and uniform grains were grown with RMS roughness of 9.4 nm at substrate temperature of 523 K. The optical results indicated that the optical transmittance of the films increases with increasing substrate temperature up to 523 K, thereafter decreases. The optical band of the films increases with substrate temperature initially, thereafter decreased at higher temperatures. The Highest optical transmittance of 60 % and optical band gap of 3.82 eV was observed in the present study.

36 MATERIALS SCIENCE↗

The electronic structure of co-sputtered zinc indium tin oxide thin films

Zinc indium tin oxide (ZITO) transparent conductive oxide layers were deposited via radio frequency (RF) magnetron co-sputtering at room temperature. A series of samples with gradually varying zinc content was investigated. The samples were characterized with x-ray and ultraviolet photoemission spectroscopy (XPS, UPS) to determine the electronic structure of the surface. Valence and conduction bands maxima (VBM, CBM), and work function were determined. The experiments indicate that increasing Zn content results in films with a higher defect rate at the surface leading to the formation of a degenerately doped surface layer if the Zn content surpasses {approx}50%. Furthermore, the experiments demonstrate that ZITO is susceptible to ultraviolet light induced work function reduction, similar to what was earlier observed on ITO and TiO{sub 2} films.

36 MATERIALS SCIENCE↗

Nanoindentation Studies Of Hard Nanocomposite Ti-B-N Thin Films

Titanium boron nitride (Ti-B-N) films were deposited by reactive magnetron sputtering using single Titanium diboride (TiB{sub 2}) target in different Ar-N{sub 2} gas mixtures. The influence of N{sub 2}:Ar ratio on the microstructure and mechanical properties of the deposited films have been investigated. Atomic force microscopy analysis indicated the grain size decreases with incorporation of nitrogen in the films. Nanoindentation studies have shown the hardness decreases with nitrogen incorporation.

36 MATERIALS SCIENCE↗

Modifications in structural and electronic properties of TiO{sub 2} thin films using swift heavy ion irradiation

We report on the structural and electronic properties of swift heavy ion (SHI) irradiated pristine TiO{sub 2} thin films, deposited by radio frequency magnetron sputtering on sapphire substrates. The high resolution x-ray diffraction and Raman measurements show a structural phase transition from anatase to admixture of brookite and rutile phases of TiO{sub 2} with increasing SHI fluence followed by a significant distortion in the TiO{sub 6} octahedra. The modification in the electronic structure stimulated by SHI irradiation has been investigated using x-ray absorption (XAS) experiments at the O K and Ti L{sub 3,2} absorption edges. The O K edge spectra clearly indicate the splitting of the pre-edge spectral features having t{sub 2g} and e{sub g} symmetry bands due to structural disorder/distortion induced by irradiation. The intensity of the SHI generated components at the O K edge increases monotonically, which can be correlated to the modification in unoccupancies associated with O 2 p orbitals hybridized with Ti 3 d states. The XAS spectra at the Ti L{sub 3,2} edge further authenticate that SHI creates a controlled structural disorder/distortion in the TiO{sub 6} octahedra.

36 MATERIALS SCIENCE↗

Influence of Al/CuO reactive multilayer films additives on exploding foil initiator

An investigation on the influence of Al/CuO reactive multilayer films (RMFs) additives on exploding foil initiator was performed in this paper. Cu film and Cu/Al/CuO RMFs were produced by using standard microsystem technology and RF magnetron sputtering technology, respectively. Scanning electron microscopy characterization revealed the distinct layer structure of the as-deposited Al/CuO RMFs. Differential scanning calorimetry was employed to ascertain the amount of heat released in the thermite reaction between Al films and CuO films, which was found to be 2024 J/g. Electrical explosion tests showed that 600 V was the most matching voltage for our set of apparatus. The explosion process of two types of films was observed by high speed camera and revealed that compared with Cu film, an extra distinct combustion phenomenon was detected with large numbers of product particles fiercely ejected to a distance of about six millimeters for Cu/Al/CuO RMFs. By using the atomic emission spectroscopy double line technique, the reaction temperature was determined to be about 6000-7000 K and 8000-9000 K for Cu film and Cu/Al/CuO RMFs, respectively. The piezoelectricity of polyvinylidene fluoride film was employed to measure the average velocity of the slapper accelerated by the explosion of the films. The average velocities of the slappers were calculated to be 381 m/s and 326 m/s for Cu film and Cu/Al/CuO RMFs, respectively, and some probable reasons were discussed with a few suggestions put forward for further work.

36 MATERIALS SCIENCE↗

Unexpected short- and medium-range atomic structure of sputtered amorphous silicon upon thermal annealing

We investigate the structure of magnetron-sputtered (MS) amorphous silicon (a-Si) prepared under standard deposition conditions and compare this to pure ion-implanted (II) a-Si. The structure of both films is characterized in their as-prepared and thermally annealed states. Significant differences are observed in short- and medium-range order following thermal annealing. Whereas II a-Si undergoes structural relaxation toward a continuous random network, MS a-Si exhibits little change. Cross-sectional transmission electron microscopy reveals the presence of nanopores in the MS film consistent with reduced mass-density. Therefore, the short- and medium-range order of annealed, MS a-Si is tentatively attributed to these pores.

36 MATERIALS SCIENCE↗

X-ray diffraction and surface acoustic wave analysis of BST/Pt/TiO{sub 2}/SiO{sub 2}/Si thin films

High dielectric constant and electrostriction property of (Ba, Sr)Ti0{sub 3} (BST) thin films result in an increasing interest for dielectric devices and microwave acoustic resonator. Barium strontium titanate (Ba{sub 0.645}Sr{sub 0.355}TiO{sub 3}) films of about 300 nm thickness are grown on Pt(111)/TiO{sub 2}/SiO{sub 2}/Si(001) substrates by rf magnetron sputtering deposition techniques. X-ray diffraction is applied for the microstructural characterization. The BST films exhibit a cubic perovskite structure with a dense and smooth surface. A laser acoustic waves (LA-waves) technique is used to generate surface acoustic waves (SAW) propagating in the BST films. Young's modulus E and the Poisson ratio {nu} of TiO{sub 2,} Pt and BST films in different propagation directions are derived from the measured dispersion curves. Estimation of BST elastics constants are served in SAW studies. Impact of stratification process on SAW, propagating along [100] and [110] directions of silicon substrate, has been interpreted on the basis of ordinary differential equation (ODE) and stiffness matrix method (SMM). A good agreement is observed between experimental and calculated dispersion curves. The performed calculations are strongly related to the implemented crystallographic data of each layer. Dispersion curves are found to be sensitive to the SAW propagation direction and the stratification process for the explored frequency ranges 50-250 MHz, even though it corresponds to a wave length clearly higher than the whole films thickness.

36 MATERIALS SCIENCE↗

Reduction of leakage currents with nanocrystals embedded in an amorphous matrix in metal-insulator-metal capacitor stacks

CaTiO{sub 3} layers with varying thicknesses in metal-insulator-metal capacitor stacks were deposited at 550 deg. C using radio-frequency magnetron sputtering. The combination of electrical and transmission electron microscopy measurements allows a correlation of k-value and leakage current to the degree of crystallinity. Experiments show that higher crystallinity and, therefore, higher k-values lead to increasing leakage currents and change of conduction mechanisms. However, leakage currents are significantly reduced when crystallites are embedded in an amorphous matrix. Selective growth of these crystallites is owed to cube-on-cube nucleation of CaTiO{sub 3} on {l_brace}011{r_brace} Pt.

36 MATERIALS SCIENCE↗

Sublattice-specific ordering of ZnO layers during the heteroepitaxial growth at different temperatures

The effect of the substrate temperature on the sublattice ordering in ZnO layers grown by reactive pulsed magnetron sputtering on sapphire has been investigated by different techniques. The improvement of the crystal quality and heteroepitaxial growth at relatively low temperatures (550 deg. C) is verified by x-ray diffraction, high-resolution transmission electron microscopy, Rutherford backscattering spectrometry in channeling mode (RBS/C), and Raman spectroscopy. Sublattice-resolved analysis by resonant RBS/C and Raman spectroscopy reveals that the progressive transition to the single crystal phase is accomplished in a faster way for Zn- than for O-sublattice. This behavior is attributed to the preferential annealing of defects in the Zn sublattice at low temperatures when compared to those of the O sublattice.

36 MATERIALS SCIENCE↗

Thickness effect on laser-induced-damage threshold of indium-tin oxide films at 1064 nm

Laser-induced-damage characteristics of commercial indium-tin oxide (ITO) films deposited by DC magnetron sputtering deposition on K9 glass substrates as a function of the film thickness have been studied at 1064 nm with a 10 ns laser pulse in the 1-on-1 mode, and the various mechanisms for thickness effect on laser-induced-damage threshold (LIDT) of the film have been discussed in detail. It is observed that laser-damage-resistance of ITO film shows dramatic thickness effect with the LIDT of the 50-nm ITO film 7.6 times as large as the value of 300 nm film, and the effect of depressed carrier density by decreasing the film thickness is demonstrated to be the primary reason. Our experiment findings indicate that searching transparent conductive oxide (TCO) film with low carrier density and high carrier mobility is an efficient technique to improve the laser-damage-resistance of TCO films based on maintaining their well electric conductivity.

36 MATERIALS SCIENCE↗

Anomalously high thermoelectric power factor in epitaxial ScN thin films

Thermoelectric properties of ScN thin films grown by reactive magnetron sputtering on Al{sub 2}O{sub 3}(0001) wafers are reported. X-ray diffraction and elastic recoil detection analyses show that the composition of the films is close to stoichiometry with trace amounts ({approx}1 at. % in total) of C, O, and F. We found that the ScN thin-film exhibits a rather low electrical resistivity of {approx}2.94 {mu}{Omega}m, while its Seebeck coefficient is approximately {approx}-86 {mu}V/K at 800 K, yielding a power factor of {approx}2.5 x 10{sup -3} W/mK{sup 2}. This value is anomalously high for common transition-metal nitrides.

36 MATERIALS SCIENCE↗

Faraday effect in ZnO:Mn thin films

Undoped and Mn-doped ZnO transparent thin films were grown by RF magnetron co-sputtering. The films are nanocrystalline, with wurtzite-structure grains of a typical size of 20 nm, with a preferential orientation of the c-axis perpendicular to the surface. Although, according to the Raman spectroscopy data, Mn mostly substitutes Zn in the lattice sites, factor that is considered favorable for ferromagnetism in this material, the ZnO:Mn films are paramagnetic at room temperature as it follows from our Faraday effect (FE) measurements. The FE spectra show a significant influence of the Mn ions for photon energies sufficiently below the ZnO:Mn band gap but not in its vicinity.

36 MATERIALS SCIENCE↗

Nano-structural Characteristics of N-doped ZnO Thin Films and Fabrication of Film Bulk Acoustic Resonator Devices

N-doped ZnO thin films (ZnO:N) with c-axis preferred orientation were prepared on p-Si(100) wafers, using an RF magnetron sputter deposition. For ZnO deposition, N{sub 2}O gas was employed as a dopant source and various deposition conditions such as N{sub 2}O gas fraction and RF power were applied. In addition, the film bulk acoustic resonator (FBAR) devices with three kinds of top electrodes patterns were fabricated by using the N-doped ZnO thin films as the piezoelectric layers. The depth profiles of the nitrogen [N] atoms incorporated into the ZnO thin films were investigated by an Auger Electron Spectroscopy (AES) and the nano-scale structural characteristics of the N-doped ZnO (ZnO:N) thin films were also investigated by a scanning electron microscope (SEM) technique. The fabricated resonators were evaluated by measuring the return loss (S{sub 11}) characteristics using a probe station and E8361A PNA Network Analyzer.

36 MATERIALS SCIENCE↗

Intrinsic Ferromagnetism Observed in ZnO Thin Film

A ZnO film was deposited on a silicon wafer by magnetron sputtering, and the magnetic and the electronic properties have been studied The magnetic property measurements show that the ZnO film is ferromagnetic at room temperature. Through the magnetoresistance (MR) measurement, it is found that ZnO reveals a negative MR at 80, 50, 20, 10 and 6 K, which is induced by the weak-localization effect. However, a positive MR as large as 19.8% was observed, when temperature was reduced to 2 K. As far as the mechanism of the huge positive MR is concerned, it is suggested to be due to the spin splitting induced by the s-d-like interaction. Through the discussion on the huge positive MR, we demonstrate that the observed ferromagnetism in ZnO is intrinsic, not from external impurities.

36 MATERIALS SCIENCE↗

Control of the optical and crystalline properties of TiO{sub 2} in visible-light active TiO{sub 2}/TiN bi-layer thin-film stacks

Multi-layered thin films of TiO{sub 2} and TiN were created by rf reactive magnetron sputtering, and their crystalline, optical, and photoelectrochemical properties were measured. The overall composition of the films (TiO{sub 2}-to-TiN ratio) was kept constant with the height of each film. The number of layers and thickness of each layer was controlled to create bi-layer thin films that were composed of: 9 bi-layers, 18 bi-layers, 27 bi-layers, 36 bi-layers, and 45 bi-layers. XRD patterns were observed for each film after annealing to measure the grain size and composition of anatase and rutile as a function of temperature. It was found that the phase-transition temperature is able to be substantially controlled (between 550 deg. C and 850 deg. C) for the anatase to rutile transition by varying the number of layers/thickness of each layer. In addition, bi-layer stacking significantly affected the film's optical properties by lowering the bandgap into the visible-light region, and also showed up to three times the improvement in photoelectrochemical performance under uv and visible irradiation. Overall, bi-layer stacking of TiO{sub 2}/TiN films has shown a unique and highly desirable control over several important physical characteristics that can be beneficial for many applications, such as high-temperature sensors and optoelectronic devices.

36 MATERIALS SCIENCE↗

Iron and nitrogen self-diffusion in non-magnetic iron nitrides

The self-diffusion of iron and nitrogen is measured in nm range non-magnetic iron nitride thin films. Two non-magnetic iron nitrides, Fe{sub 2.23}N and FeN, were studied using neutron reflectivity. Neutron reflectivity with a depth resolution in the sub-nm range has a different scattering cross section for isotopes, providing a unique opportunity to measure very small diffusivities. The isotope heterostructure in thin film multilayers [Fe-N/{sup 57}Fe-N]{sub 10} and [Fe-N/Fe-{sup 15}N]{sub 10} were prepared using magnetron sputtering. It was observed that nitrogen diffuses slower than iron although the atomic size of iron is larger than that of nitrogen. It was found that a significantly larger group of N atoms participates in the diffusion process than of Fe, making N diffusion slower than that of Fe.

36 MATERIALS SCIENCE↗