Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JOINT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,675 records · Page 93
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Nuclear Thermal Propulsion: A Joint NASA/DOE/DOD Workshop

Papers presented at the joint NASA/DOE/DOD workshop on nuclear thermal propulsion are compiled. The following subject areas are covered: nuclear thermal propulsion programs; Rover/NERVA and NERVA systems; Low Pressure Nuclear Thermal Rocket (LPNTR); particle bed reactor nuclear rocket; hybrid propulsion systems; wire core reactor; pellet bed reactor; foil reactor; Droplet Core Nuclear Rocket (DCNR); open cycle gas core nuclear rockets; vapor core propulsion reactors; nuclear light bulb; Nuclear rocket using Indigenous Martian Fuel (NIMF); mission analysis; propulsion and reactor technology; development plans; and safety issues.

Clark, John S.↗
NASA NTRS1991

High-frequency data observations from space shuttle main engine low pressure fuel turbopump discharge duct flex joint tripod failure investigation

Observations made by Marshall Space Flight Center (MSFC) engineers during their participation in the Space Shuttle Main Engine (SSME) low pressure fuel turbopump discharge duct flex joint tripod failure investigation are summarized. New signal processing techniques used by the Component Assessment Branch and the Induced Environments Branch during the failure investigation are described in detail. Moreover, nonlinear correlations between frequently encountered anomalous frequencies found in SSME dynamic data are discussed. A recommendation is made to continue low pressure fuel (LPF) duct testing through laboratory flow simulations and MSFC-managed technology test bed SSME testing.

Zoladz, T. F.↗
NASA NTRS1991

Development of a rotary joint fluid coupling for Space Station Freedom

The design and development is described of a rotary joint fluid coupling for Space Station Freedom. The function of this fluid coupling is to transfer a heat rejection fluid between stationary and rotating interfaces with the Space Station thermal bus system. The design of this coupling incorporates a modular type design to allow maximum flexibility, two types of seals (mechanical face seals and shaft lip seals) for redundancy, materials with excellent ammonia compatibility, and coatings that enhance seal wear resistance and increased protection against corrosion. This design was thoroughly tested and met all design requirements. Potential applications of this hardware include uses in gun turrets, coal slurries, farming equipment, and any other applications that require the low leakage transfer of fluids between stationary and rotating interfaces.

Costulis, John A.↗
NASA NTRS1992

Invacuo tribological evaluation of coarse-pitch gears for use on the Space Station alpha joint

Existing invacuo or ambient test data of slow-speed (less than 30 meters/minute pitch line velocity), coarse-pitch gears could not be found suitable for use in evaluating gear materials and surface treatments for the gear-driven bearing race of the Solar Alpha Rotary Joint (SARJ) for Space Station Freedom (SSF). Gear testing was conducted by AEC-Able Engineering Company, Inc. to obtain design data for this critical SSF component. Some bull gear/pinion/lubrication combinations endured over 600,000 cycles (100 SSF years) without measurable wear, while other combinations experienced surface treatment degradation after only 40,000 cycles (seven SSF years). No catastrophic failures, such as seizing or tooth breakage, occurred during any test, all of which were run at least 201,000 cycles (34.5 SSF years). Specific results such as debris characteristics, mechanical efficiencies, effectiveness and degradation of lubrication, and wear data for the various gear combinations tested are described.

Allen, Scotty R.↗
NASA NTRS1992

Development of a truss joint for robotic assembly of space structures

This report presents the results of a detailed study of mechanical fasteners which were designed to facilitate robotic assembly of structures. Design requirements for robotic structural assembly were developed, taking into account structural properties and overall system design, and four candidate fasteners were designed to meet them. These fasteners were built and evaluated in the laboratory, and the Hammer-Head joint was chosen as superior overall. It had a high reliability of fastening under misalignments of 2.54 mm (0.1 in) and 3 deg, the highest end fixity (2.18), the simplest end effector, an integral capture guide, good visual verification, and the lightest weight (782 g, 1.72 lb). The study found that a good design should incorporate chamfers sliding on chamfers, cylinders sliding on chamfers, and hard surface finishes on sliding surfaces. The study also comments on robot flexibility, sag, hysteresis, thermal expansion, and friction which were observed during the testing.

Parma, George F.↗
NASA NTRS1992

Noncircular rolling joints for vibrational reduction in slewing maneuvers

A rolling joint is provided for obtaining slewing maneuvers for various apparatus including space structures, space vehicles, robotic manipulators, and simulators. Two noncircular cylinders, namely a drive and a driven cylinder, are provided in driving contact with one another. This contact is maintained by two pairs of generally S-shaped bands, each pair forming a generally 8-shaped coupling tightly about the circumferential periphery of the noncircular drive and driven cylinders. A stationarily fixed arm extends between and is rotatably journalled with a drive axle and a spindle axle respectively extending through selected rotational points of the drive cylinder and of the driven cylinder. The noncircular cylinders are profiled to obtain the desired varying gear ratio. The novelty of the present invention resides in using specifically profiled noncircular cylinders to obtain a desired varying gear ratio.

Chew, Meng-Sang↗
NASA NTRS1992

Lubricant evaluation of the alpha and beta joints, phase 2

A research study was conducted to evaluate dry film lubrication of long life space components such as the alpha and beta joints of the Space Station. The problem addressed in the report pertains to the longevity of sputtered MoS2 or ion plated lead films in a rolling contact environment. A special technique was devised for the experiments, which incorporated a coated ball cyclically loaded against a flat plate. At fixed intervals the surface of the coating was photographed at 100X magnification. By computer scanning the photographs, the rate of coating loss was determined. Experimental variables include load and surface finish of the plate. A theory was developed to analyze the state of stress between ball and flat. The stress condition in the ball apparatus was related to the state of stress under rolling contact conditions. Based on the experiments life appeared to decrease with increasing load and increasing surface roughness. An ion plated lead film gave better life than a sputtered MoS2 film. However, by keeping the interfacial shear stress at a low level, adequate coating life was achieved for either coating. For the lead film, the critical stress was about 0.19 GPa (28 ksi). The study dealt only with mechanical wear. Before a coating is selected for a critical space application, other factors such as reaction with atomic oxygen must also be considered.

Kannel, J. W.↗
NASA NTRS1991

Joint inversion of shear wave travel time residuals and geoid and depth anomalies for long-wavelength variations in upper mantle temperature and composition along the Mid-Atlantic Ridge

Measurements were carried out for SS-S differential travel time residuals for nearly 500 paths crossing the northern Mid-Atlantic Ridge, assuming that the residuals are dominated by contributions from the upper mantle near the surface bounce point of the reflected phase SS. Results indicate that the SS-S travel time residuals decrease linearly with square root of age, to an age of 80-100 Ma, in general agreement with the plate cooling model. A joint inversion was formulated of travel time residuals and geoid and bathymetric anomalies for lateral variation in the upper mantle temperature and composition. The preferred inversion solutions were found to have variations in upper mantle temperature along the Mid-Atlantic Ridge of about 100 K. It was calculated that, for a constant bulk composition, such a temperature variation would produce about a 7-km variation in crustal thickness, larger than is generally observed.

Sheehan, Anne F.↗
NASA NTRS1991

Numerical simulations of thermal detection of disbonds in lap joints

A 2D time-dependent FEM heat-transfer algorithm that is unconditionally stable and implicit is presently used to solve for the time-dependence of a structure's temperature. By examining data-reduction techniques in the framework of simulation data, the contrast enhancement afforded by a given technique can be evaluated without regard to experimental error. The present computational simulations demonstrate that the time-derivative technique can clearly delineate the substructure of lap-joint geometries; in addition, histograms of the front surface images are able to quantitatively measure contrast-enhancements for various inspection and data-reduction techniques.

Howell, P. A.↗
NASA NTRS1992

A criterion for joint optimization of identification and robust control

A criterion for system identification is developed that is consistent with the intended used of the fitted model for modern robust control synthesis. Specifically, a joint optimization problem is posed which simultaneously solves the plant model estimate and control design, so as to optimize robust performance over the set of plants consistent with a specified experimental data set.

Bayard, D. S.↗
NASA NTRS1993

Adjustable-Torque Truss-Joint Mechanism

Threaded pin tightened or loosened; tedious trial-and-error procedure shortened. Mechanism joining strut and node in truss structure preloaded to desired stress to ensure tight, compressive fit preventing motion of strut during loading or vibration. Preload stress on stack of Belleville spring washers adjusted by tightening or loosening threaded Belleville-washer-alignment pin. Pin turned, by use of allen wrench, to adjust compression preload on Belleville washers and adjusts joint-operating torque.

Bush, Harold G.↗
NASA NTRS1992

Boom and chassis articulation joints

The primary goal of our design project was to develop articulation joints for the chassis and boom of the proof-of-concept lunar vehicle. This is an ongoing project and the work of previous student groups was extensively reviewed. Some of the ideas generated are variations of past proposals. Although the project is funded by NASA/USRA, it is totally a student design effort.

Murphy, Joel T., Jr.↗
NASA NTRS1992

TOPEX/POSEIDON joint verification plan

TOPEX/POSEIDON is a satellite mission that will use altimetry to make precise measurements of sea level with the primary goal of studying global ocean circulation. The mission is jointly conducted by the United States' National Aeronautics and Space Administration (NASA) and the French space agency, Centre National d'Etudes Spatiales (CNES). The current plans call for a launch of the satellite in August 1992. The primary mission will last 3 years, and provisions were made to extend the mission for an additional 2 years. The mission was coordinated with a number of international oceanographic and meteorological programs, including the World Ocean Circulation Experiment and the Tropical Ocean and Global Atmosphere Program, both of which are sponsored by the World Climate Research Program. The observations of TOPEX/POSEIDON are timed to provide a global perspective for interpreting the in situ measurements collected by these programs and in turn will be combined with observations of other satellites to achieve a global, four-dimensional description of the circulation of the world's oceans. In the autumn of 1987, an international team of 38 Principal Investigators was selected to participate in the mission. These scientists have been working closely with the TOPEX/POSEIDON Project to refine the mission design and science plans. During the first 6 months after launch, a number of these investigators will join with the project to conduct a wide range of oceanographic and geophysical investigations using the TOPEX/POSEIDON data. The purpose of these investigations is to demonstrate the scientific utility of the mission to the international scientific community.

Source record↗
NASA NTRS1992

Description of the Joint Damping Experiment (JDX)

The overall objective is to develop a small-scale shuttle flight experiment which allows researchers to: (1) characterize the influence of gravity and joint gaps on a small-scale truss model, and (2) evaluate the applicability of low-g aircraft test results for predicting on-orbit behavior. The experiment consists of a three-bay truss and associated hardware for truss excitation and measurement of oscillations. Other aspects of the investigation are presented in viewgraph form.

Folkman, Steven L.↗
NASA NTRS1992

A research experiment on facilitation and formation of joint research and development programs between government, industry, and universities: Overview, preliminary findings, and observations

Presented is an overview of an experiment to explore the free-market approach to public-private collaboration through the development and implementation of a joint venture mechanism to enable formation of R&D projects between government, industry and academia. Some preliminary results related to time-to-commercialization and economic competitiveness are discussed.

Shariq, Syed Z.↗
NASA NTRS1992

Joint NASA/USAF Airborne Field Mill Program - Operation and safety considerations during flights of a Lear 28 airplane in adverse weather

A NASA Langley Research Center Learjet 28 research airplane was flown in various adverse weather conditions in the vicinity of the NASA Kennedy Space Center from 1990-1992 to measure airborne electric fields during the Joint NASA/USAF Airborne Field Mill Program. The objective of this program was to characterize the electrical activity in various weather phenomena common to the NASA-Kennedy area in order to refine Launch Commit Criteria for natural and triggered lightning. The purpose of the program was to safely relax the existing launch commit criteria, thereby increasing launch availability and reducing the chance for weather holds and delays. This paper discusses the operational conduct of the flight test, including environmental/safety considerations, aircraft instrumentation and modification, test limitations, flight procedures, and the procedures and responsibilities of the personnel in the ground station. Airborne field mill data were collected for all the Launch Commit Criteria during two summer and two winter deployments. These data are now being analyzed.

Fisher, Bruce D.↗